Lutron Electronics QSN-4S16-S-347, QSN-4T16-S, QSN-4T20-S, QSN-4T16-S-347, QSN-4S20-S Programming Manual

...

BUTTON AND LED LOCATIONS

TROUBLESHOOTING

WIRED INPUTS

USING THIS GUIDE

OTHER QS LINK DEVICES

QS SENSOR MODULE (QSM) WITH WIRED OR WIRELESS INPUT DEVICES

Lutron Electronics Co., Inc. | 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.

Help 1.800.523.9466 U.S.A., Canada and the Caribbean +1.888.235.2910 México +1.610.282.3800 Others

This guide is divided into sections. Each section deals with a particular feature or set of features of the Energi Savr NodeTM unit and the equipment connected to it. Depending on the connected equipment and the intended use of your Energi Savr NodeTM unit, some sections may not apply. See below to determine which sections should be read.

0-10 V Outputs l Salidas l Sorties

4 X 50 mA

(Sinking O

y l Rece

pcion

solam

te l Réc

epteur de

urant seulem

nt)

QSN-4T16-S-347

120-277 V~ 50/60 Hz 500 mA

0-10 V / Softswitch

Coopersburg, PA 18036, U.S.A.

500-14444 Rev. A

saving energy since 1961

Energi Savr Node

Type 1

Enclosure

243C

LISTED

Ind. Cont. Eq.

4 Softswit

Circuits l Circuitos

Capacity l Capacidad l Capacité :

C PELV / NEC

lass 2

Input Groups | Grupos de

entrada

Groupes d’entreés :

X 65 mA

QS Link | Elance | L

iaison :

62 mA

WARNING

Risk of Electric Shock. May Result in serious injury or death. More than one disconnect may be required to de-energize this device. Disconnect all power sources before servicing unit.

ADVERTENCIA

Riesgo choque eléctrico. Puede resultar en lesiones graves o muerte. Puede necesitarse más de una desconexión para desenergizar este dispositivo. Desconecte todas las fuentes de alimentación antes de prestar servicio a la unidad.

AVERTISSEMENT

Risque d'électrocution. Peut causer le décès de la personne ou de graves lésions. Plus d’un débranchement peut être Débrancher toutes les sources d’énergie avant de procéder à l’entretien de cette unité.

4 x 16 A 120-277 V~ 4 x 0,5 HP 120 V~ 4 x 1,5 HP 277 V~

4 x 16 A 347 V~

All Energi Savr NodeTM units

Read:

Load Setup

Energi Savr NodeTM with Softswitch® unit

(QSN-4S16-S, QSN-4S16-S-347, QSN-4S20-S)

Energi Savr NodeTM for 0-10 V unit

(QSN-4T16-S, QSN-4T16-S-347, QSN-4T20-S)

Type 1 Enclosure

4 Softswitch

Circuits l C

irc

uit

Capacity l Capacidad l Capacité :

QSN-4S16-S-347

120-277 V 50/60 Hz 500 mA

Softswitch

Coopersburg, PA 18036, U.S.A.

500-14445 Rev. A

saving energy since 1961

Energi Savr Node

WARNING

Risk of Electric Shock. May Result in serious injury or death. More than one disconnect may be required to de-energize this device. Disconnect all power sources before servicing unit.

ADVERTENCIA

AVERTISSEMENT

243C

LISTED

Ind. Cont. Eq.

C PE

V / NEC

Class 2

Input Groups | Gru

pos de entrada

Groupes d’entreés :

X 65 mA

QS Link | Elance | Liaison

V -

462 mA

4 x 16 A 120-277 V~ 4 x 0,5 HP 120 V~ 4 x 1,5 HP 277 V~

4 x 16 A 347 V~

LED Feedback

LED LED Behavior Description

Occ

(Occupancy Sensor)

Continuous On

Sensor detects Vacancy

1 ﬂash per second

Sensor detects Occupancy

Off

Sensor never detected

Daylight

(Daylight Sensor )

Continuous On

Sensor is detected

Flashing

Sensor information transmitting on the QS link

Off

Sensor never detected/sensor not seeing light

(Infrared Receiver)

Continuous On Receiver is detected

Flashing

IR button press detected

Off

Receiver never detected

Switch

(NEC

® Class2 Switch)

Continuous On

Switch detected/open

Flashing

Switch button press detected

Off

Switch never detected

CCI

(Contact Closure Input)

Continuous On

Contact detected/open

Flashing

Contact closed

Off

Contact never detected

Emerg

(Emergency Contact Closure Input)

Continuous On

Normal operation/Contact Closed/ Jumpered

Rapid ﬂash

Emergency Mode/Contact Open/ Jumper missing

QS Link

On/Flashing

Device transmitting/receiving on the QS link

3 quick ﬂashes every 4 seconds

Communication error

Off

Device not transmitting/receiving on the QS link

Wired Continuous On

Wired sensor

Zone

Continuous On

Load is on

Off

Load is off

Troubleshooting using Symptoms

Symptom Cause Solution

Unable to add daylight sensor to a zone

Existing daylight sensor already assigned to the zone

Unassign the existing daylight sensor and try again.

Unable to add an occupancy sensor to a zone

16 sensors have already been assigned

No more than 16 sensors can be assigned to one ESN unit. Unassign sensors until below 16 sensor limit.

Daylight sensor fails to turn on a zone

Occupancy sensor is overriding the zone

Daylight sensors will not turn a zone on if an occupancy sensor assigned to that zone detects that the room is vacant.

Switched zone daylighting: incorrect light level set during Daylighting Setup

Reset the daylighting set point. See

Daylighting Setup.

When associating a QSM to the Energi Savr NodeTM unit, the ‘QSM’ LED ﬂutters for 1 second, then turns off

A QSM has already been associated to the Energi Savr NodeTM unit.

To clear the QSM association and any Energi Savr Node

TM unit zone assignments

to any QSM inputs, press and hold the Input button on the Energi Savr NodeTM unit for 10 seconds. The ‘Input’ LED will ﬂutter for 1 second, then turn off.

When associating a wireless input device to a QSM, the QSM responds with 10 short beeps

Maximum number of associations to the QSM has been exceeded for that wireless input device type.

Unassign any unnecessary wireless inputs of that device type and try again.

When associating a wireless input device to a QSM, the QSM responds with 5 short beeps

Input device is already associated to another QSM on the QS link.

If you choose to ignore the warning and try to associate the same input device to the QSM a second time, the input device will be removed from association with the previous QSM and will now be associated with the new QSM. Note: This will also remove any Energi Savr Node

programming that the wireless device may have had through the previous QSM.

QS Link LED quickly ﬂashes 3 times every 4 seconds

QS Link communication error.

Check QS Link wiring

Technical Assistance

U.S.A. / Canada: 1.800.523.9466 Mexico: +1.888.235.2910 Other Countries: +1.610.282.3800

IMPORTANT NOTES

Energi Savr NodeTM with Softswitch® unit

(QSN-4S16-S, QSN-4S16-S-347, QSN-4S20-S)

Energi Savr NodeTM for 0-10 V unit

(QSN-4T16-S, QSN-4T16-S-347, QSN-4T20-S)

Energi Savr NodeT

manual programming guide

English

1. Manual Programming: This document describes manual

programming via the buttons on the front of the Energi Savr NodeTM unit. For programming using the Apple iPod touch or iPhone mobile digital devices, please see the Energi Savr NodeTM app available from the Apple AppStore online store.

2. Use only compatible Lutron® sensors and controls.

032449 | Rev. C | 05/2014

24/7 Help

U.S.A., Canada and the Caribbean

1.800.523.9466

México

+1.888.235.2910

Others

+1.610.282.3800

Fax

+1.610.282.6311

If you have wired sensor inputs wired directly to the Energi Savr NodeTM unit input group terminal blocks, see below to determine which additional sections to read.

www.lutron.com

P/N 032449 Rev. C 05/2014

Apple, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. AppStore is a service mark of Apple Inc.

Lutron, GRAFIK Eye, Pico, seeTouch, Softswitch and ) are registered trademarks, and Energi Savr Node and Radio Powr Savr are trademarks of Lutron Electronics Co., Inc.

All Wired Inputs

Read:

Energi Savr NodeTM (ESN) Unit Wired Input Setup

Energi Savr Node

Unit

LUTRON

Dry Contact Closure Switch

Wires to “Switch”, “CCI”, or “EMERG” Input

Energi Savr

Node

TM (ESN)

Unit Wired Input Setup

Wired Occupancy Sensor

Wires to “Occ” Input

Additional Sections:

Energi Savr NodeTM (ESN)

Unit Wired Input Setup

Occupancy Setup

Wired Wallstation or Infrared (IR) Sensor

Wires to “IR” Input

Energi Savr

NodeTM (ESN) Unit Wired Input Setup

Wired Daylight Sensor

Wires to “Daylight” Input

Additional Sections:

Energi Savr NodeTM (ESN)

Unit Wired Input Setup

Daylighting Setup

If you have a QSM wired to the Energi Savr NodeTM unit QS Link terminal block, read sections QS Sensor Module (QSM) Input Setup and

QS Sensor Module (QSM) Zone Assignment. Some parts of the section

may not apply, depending on the devices connected to the QSM. See below to determine which additional subsections to read for each type of connected device.

QSM Wireless Input Devices

Communicates with QSM via Radio Frequency (RF)

Read:

Subsection: Associating Wireless Input

Devices to a QSM

QS Sensor Module (QSM)

Wires to “QS Link” Terminal Block on

Energi Savr Node

TM unit

Wireless Occupancy Sensor

Additional Sections:

Occupancy Setup

Subsection: Assign Zones to

QSM Inputs

Wireless Daylight Sensor

Additional Sections:

Daylighting Setup

Subsection: Assign Zones to

QSM Inputs

Wired Occupancy Sensor

Additional Sections:

Occupancy Setup

Subsection: Assign Zones to

QSM Inputs

Wired Daylight Sensor

Additional Sections:

Daylighting Setup

Subsection: Assign Zones to

QSM Inputs

LUTRON

Pico® Wireless Controller

Additional Sections:

Subsection: Assign Zones to Pico®

Wireless Controller (through QSM)

QS Link

Wired Wallstation or Infrared (IR) Sensor

Additional Sections:

Subsection: Assign Zones

to QSM Inputs

Energi Savr NodeTM Unit

QS Sensor Module

Read:

QS Sensor Module (QSM)

Input Setup

QS Sensor Module (QSM)

Zone Assignment

QSM Wired Input Devices

Wires to Input Terminal Blocks on QSM

Read:

» Subsection: Associating Wired

Input Devices to a QSM

QS Link

If you have other devices wired to the Energi Savr NodeTM unit QS Link terminal block, see below to determine which additional sections to read.

Energi Savr NodeTM Unit

Wired seeTouch® QS Wallstation

Additional Sections:

» Wired seeTouch® QS Wallstations Programming

QSE-IO Input/Output Interface

Additional Sections:

» QSE-IO Input/Output Interface Programming

CCI1 CCI 2

CCI 3

CCI 4

COM CCI 5

0-24 V 1 A 0-24 V ½ A

O N

CCO 1 NC

CCO 1 NO

CCO 2 NC CCO 2 NO

1-2 COM

CCO 3 NC

CCO 4 NO

CCO 3 NO

CCO 4 NC

3-4 COM

CCO 5 NC

5 COM

CCO 5 NO

MUX

COM V+

MUX

500-13491 Rev. B

CCO 1

CCO 2

CCO 3

CCO 4

CCO 5

STAT

800.523.9466

+1.610.282.3800

www.lutron.com/qs

QSE-IO

24 V 100 mA

243C IND. CONT. EQ.

02755761323 1

8 7 6 5 4 3 2 1

4 3 2 1

GRAFIK Eye® QS Control Unit or QS Timeclock

Additional Sections:

» GRAFIK Eye® QS Control Unit or QS Time clock Programming

LUTRON

Zones

Inputs

PROGRAMMINGLEDs and BUTTON PRESSES

Lutron Electronics Co., Inc. | 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.

Help 1.800.523.9466 U.S.A., Canada and the Caribbean +1.888.235.2910 México +1.610.282.3800 Others

1. Enter Load Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds. LEDs for Group 1 Inputs and

‘Default’ will blink once per second.

2. Select options. Press the Option button to select the option and then use the and buttons for each zone to select the choice

for each option.

LED

Option Setting Choices

Opt 2 Load Type High LED 0-10 V Dimming (default)

Med LED 10-0 V Dimming

Low LED Switched

High LED and Low LED

Receptacle

Opt 3

(not available on QSN-4S16-S or QSN-4S16-S-347)

High End Trim High-Med LEDs 100% maximum (default)

down to 55% minimum

Default + Opt 1

(not available on QSN-4S16-S or QSN-4S16-S-347)

Low End Trim Low-Med LEDs 0% minimum

up to 45% maximum

Default + Opt 2

Absolute Minimum Light Level

High-Med-Low LEDs 100% maximum

down to 0% minimum (default)

Not available on QSN-4S16-S or QSN-4S16-S-347

This setting is required in certain cities (i.e. Chicago). Check local electrical codes to verify if required.

3. Exit Load Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds to exit.

Set zone level. Use the

and buttons to adjust zone preset light level.

Assign zone. Simultaneously press then release the

and buttons to save the zone level and assign the zone to the selected

input.

To unassign a zone, simultaneously press then release the

and buttons of the desired zone. The zone LED will turn off to indicate

an unassigned zone.

Repeat setting zone level and zone assignment for each zone to be assigned to the selected input.

e. CCI input:

The LED for the currently saved option will be steady on. Press the Option button to select the desired option. The LED for the selected option will ﬂash.

CCI—Contact Closure Input

Option LED

Switch Action Feature Function

Default Momentary Sweep to

Off*

Contact closure will turn assigned zones Off

Opt 1

Maintained Enable /

Disable Afterhours Mode

† ‡

Contact closure will enable Afterhours Mode Contact open will disable Afterhours Mode

Opt 2

Maintained Zones

Preset/ Off

Contact closure will set assigned zones to preset level (preset level cannot be set to off)

Contact open will set assigned zones off

* By default, all zones are assigned and set to off, but zones can be unassigned and zone levels are adjustable to any level. † The zone must be set to Afterhours Mode to function properly. Please refer to Occupancy Setup. ‡ Default Afterhours Mode setting: 5 minute warning (assigned zones ash 3 times) before zones turn off; pressing any button activates a 45 minute delay, after

which the 5 minute warning will activate again. Receptacle loads will not blink-warn in Afterhours Mode.

Save the selected option. Press and hold the Option button for 3 seconds. The LED for the selected option will remain steady on.

Set zone levels. Use the

and buttons to adjust zone preset light levels.

Assign/Unassign zones. Simultaneously press the

and buttons of any zone to save the zone level and assign or unassign the zone to/from the selected input. A ﬂashing ‘Zone’ LED indicates an assigned zone. A ‘Zone’ LED that is off indicates an unassigned zone.

Repeat setting zone level and zone assignment for each zone to be assigned to the selected input.

f. Emerg input:

Set zone levels. Use the

and buttons to adjust zone preset light levels.

Assign zone. Simultaneously press then release the

and buttons to save the zone level and assign the zone to the selected input.

To unassign a zone, simultaneously press then release the

and buttons of the desired zone. The zone LED will turn off to indicate

an unassigned zone.

Repeat steps 2 and 3 for each desired input.

4. Exit Input Setup. Press and hold the Program button for 3 seconds to exit.

Associating Wired Input Devices to a QSM

Once wired inputs are connected to the QSM, upon power up, the QSM will automatically detect and conﬁgure the wired inputs after a valid signal is received. For example: occupied room, IR signal, etc.

If any wired inputs are moved to a different connection on the QSM, the inputs will need to be re-detected. To force the QSM to redetect all wired inputs, press and hold the Program button on the QSM for 10 seconds.

Associating Wireless Input Devices to a QSM

Wireless input devices must be associated to only one QSM before they are assigned to control system devices.

1. Enter Input Setup. Press and hold the Program button on the QSM for 3 seconds. You will hear a long 1-second beep upon

entering, and the ‘Status’ LED will blink.

2. Associate devices. For each wireless device you wish to associate, press and hold the appropriate button on the device

according to the following table:

Input Device Button

Press For

Device

Feedback

Maximum Per QSM

Radio Powr SavrTM Occupancy Sensor or Lights Off

6 seconds Dome ashes

briey

Radio Powr Savr Daylight Sensor

Link 6 seconds Dome ashes

briey

Pico

® Wireless

Controller

or Off

(bottom button)

6 seconds N/A 10

After each successful input association, QSM will respond with 3 long beeps (2 seconds each).

Note: If QSM responds in any other way, consult the Troubleshooting section on the ﬁrst page of this guide.

3. Exit Input Setup. Press and hold the Program button on the QSM for 3 seconds to exit.

QSM Association to an ESN Unit

Press and hold the Program button on the QSM for 3 seconds. You will hear a long 1-second beep upon entering, and the ‘Status’ LED will blink. The input LEDs on Energi Savr Node

TM unit(s) on the QS link will sequence through each input group.

2. Associate QSM. On the Energi Savr NodeTM unit to which the QSM will be associated, press and hold the Input button for 3

seconds until the ‘QSM’ LED on the Energi Savr Node

TM unit begins to ﬂash.

3. Exit QSM Association. Press and hold the Program button on the QSM for 3 seconds to exit.

1. Enter ESN Wired Input Setup. Press and hold the Program button for 3 seconds. LEDs for Group 1 ‘Occ’ and ‘Wired’ will blink

once per second.

2. Select input. Tap the Program button to select an input. Corresponding LED (located above input terminal) will blink. Also, LEDs

of sensors wired to the Energi Savr NodeTM unit will ﬂash to help with identiﬁcation.

3. Setup options. Follow the appropriate section for each input below.

a. Occupancy sensor:

Assign zone(s). Simultaneously press then release the

and buttons of any zone to assign the zone to the selected input. A

ﬂashing zone LED indicates an assigned zone.

To unassign a zone, simultaneously press then release the

and buttons of the desired zone. The zone LED will turn off to indicate

an unassigned zone.

b. Daylight sensor:

Assign zone(s). Simultaneously press then release the

and buttons of any zone to assign the zone to the selected input. A

ﬂashing zone LED indicates an assigned zone.

Note: Each zone can only be assigned to a single daylight sensor input. The zone must be unassigned from the input before assigning to a different daylight sensor input.

Note: Any zone set to “Receptacle” load type cannot be assigned to a daylight sensor.

To unassign a zone, simultaneously press then release the

and buttons of the desired zone. The zone LED will turn off to indicate

an unassigned zone.

c. IR receiver / IR Wallstation:

The LED for the currently saved option will be steady on. Press the Option button to select the desired option. The LED for the selected option will ﬂash.

LED

Option

Opt 1

Scene Mode Allows IR remote to select scenes (see Scene Setup

for more information) Note: CC-4BRL wallstation will only recall scenes 1-4, and CC-1BRL will only recall scene 1.

Opt 2

Zone mode (default) Allows setting of preset light levels for each zone

Save the selected option. Press and hold the Option button for 3 seconds. The LED for the saved option will remain steady on.

Set zone level (Zone Mode only). Use the and buttons to adjust zone preset light level.

Assign zone. Simultaneously press then release the

and buttons to save zone level (Zone Mode only) and assign the zone to

the selected input (Zone Mode and Scene Mode).

To unassign a zone, simultaneously press then release the

and buttons of the desired zone. The zone LED will turn off to indicate

an unassigned zone.

Note: For any keypad assigned to control a receptacle zone, Raise/Lower will not control that zone.

Repeat setting zone level (Zone Mode only) and zone assignment for each zone to be assigned to the selected input.

d. Switch input:

The LED for the currently saved option will be steady on. Press the Option button to select the desired option. The LED for the selected option will ﬂash.

Switch—NEC® Class 2 / PELV dry contact switch

Option LED

Switch Action Feature Function

Default

Maintained Zone toggle

Preset / Off (default)

Contact closure or open will toggle the state of assigned zones between a preset and off* (preset level cannot be set to off)

Opt 1

Momentary Zone toggle

Preset / Off

Contact closure will toggle the state of assigned zones between a preset and off* (preset level cannot be set to off)

Opt 2 Maintained

(dual action)

Zones Preset / Off

Contact closure will turn assigned zones on to preset level (preset level cannot be set to off)

Contact open will turn assigned zones off

Opt 3

Momentary (single action)

Zones On Contact closure will turn assigned zones on to preset level

(preset level can be set to off)

* If one or more assigned zones are on at time of contact closure/open, all assigned zones will turn off.

Save the selected option. Press and hold the Option button for 3 seconds. The LED for the selected option will remain steady on.

Continued next column...

Load Setup

Energi Savr Node

TM (ESN) Unit Wired Input Setup - continued

QS Sensor Module (QSM) Input Setup

Energi Savr Node

TM (ESN) Unit Wired Input Setup

1. 3.

ESN Wired Input Setup

QS Sensor Module (QSM) Input Setup

3.2.

Enter Load Setup

Press and hold 3 seconds

Press and hold

3 seconds

Press and hold 3 seconds

Press and hold

3 seconds

Press and hold 3 seconds

Press and hold

6 seconds

Press and hold 6 seconds

Press and hold 3 seconds

Press

Press simultaneously

Press

Press simultaneouslyPress

Press

Enter ESN Wired Input Setup

Enter QSM Wireless Input Setup Exit Setup

Enter QSM-ESN Association Exit QSM-ESN Association

Associate QSM

Select Option

Select Input

Associate Devices

Select Option

Save Option

Change Setting

Selected Input Blinks

Exit Load Setup

3. a. b.

c. d. e.

Assign Zones

Exit ESN Wired Input Setup

Set Zone Levels

Assign Zone

Set Zone Level

(IR receiver: Zone Mode Only)

ress and ho

3 secon

Press

Associating Wireless Input Devices to a QSM

QSM Association to an ESN Unit

ess and ho

Button and LED Locations

LED states:

OFF ON Blink/Flash

See written instructions at right.

Load Setup

Zones

Inputs

Figure B

Figure A

Figure C

+ 2 hidden pages

Lutron Electronics QSN-4S16-S-347, QSN-4T16-S, QSN-4T20-S, QSN-4T16-S-347, QSN-4S20-S Programming Manual

Specifications and Main Features

Frequently Asked Questions

User Manual