Lutron Electronics GRAFIK Eye QSG-3PCE, GRAFIK Eye QSG-4PCE, GRAFIK Eye QSG-6PCE Installation And Operation Manual
LUTRON
System
Installation and
Operation Guide
R
Chinese
Please Read
Contents
Installation
Features and Functions of the GRAFIK Eye QS System . 2
Wiring the GRAFIK Eye QS System . . . . . . . . . . . . . . . . . 3
Wiring the GRAFIK Eye QS System
Class 2 / PELV Cable . . . . . . . . . . . . . . . . . . . . . . . . . 4
QS System Low-Voltage Control Wiring . . . . . . . . . . . . . .5
QS System Low-Voltage Terminal Connections . . . . . . . 6
Installing the GRAFIK Eye QS System . . . . . . . . . . . . . . . 7
Zone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operation
Preprogrammed Button Functionality . . . . . . . . . . . . . . 10
General Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General Functionality: Programming Mode . . . . . . . . . .12
Zone Button Operation . . . . . . . . . . . . . . . . . . . . . . . . . .13
Quick Scene Programming . . . . . . . . . . . . . . . . . . . . . . 15
Scene Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
LED Displays for Lighting Levels . . . . . . . . . . . . . . . . . . 18
Adjusting Window Treatment Settings . . . . . . . . . . . . . .19
Timeclock Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Set Save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Set Up Occupant Sensor . . . . . . . . . . . . . . . . . . . . . . . .29
Activate System Accessories . . . . . . . . . . . . . . . . . . . . .30
Faceplate Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
The GRAFIK Eye QS System allows for control of both lights and
shades or window treatments using a single control unit. Features
include pushbutton scene recall, info screen that displays energy
savings and status, IR receiver, astronomic timeclock, occupant
sensor connection, and backlit buttons that are easy to find and
operate.
Model Number Unit Capacity Zone Capacity
(watts) (watts)
QSG - 3PCE 1 500 500
QSG - 4PCE 2 000 500
QSG - 6PCE 2 300 500
(see page 8 for additional ratings)
All units: 230 V 50/60 Hz
R
GRAFIK Eye® QS System Installation and Operation Guide 2
OK
1 2 3 4 5 6
Info screen
Displays status;
programming functions
Lighting column
Scene buttons with integral
scene indicator LEDs
Shade column
Preset and raise/lower
buttons with integral LEDs
(maximum of 3 columns)
Space for future
shade columns
Zone numbers
Zone raise/lower buttons
Zone LEDs display current
lighting zone levels
Timeclock status button
Displays current
timeclock info
OK button
Used for programming
fade time
Infrared receiver
For handheld remote use
Master buttons
Temporarily raise and lower
lighting levels on unit
USB type mini B input
{
Hinged faceplate
Hinged faceplate
Features and Functions of the GRAFIK Eye® QS System
R
GRAFIK Eye® QS System Installation and Operation Guide 3
Wiring the GRAFIK Eye® QS System
Important Wiring Information
• Use properly certified cable for all line
voltage/mains cables.
• Proper short-circuit and overload
protection must be provided at the
distribution panel.
• Install in accordance with all local and
national electrical codes.
• Class 2 / PELV terminals may be
unplugged for ease of IR, occupant
sensor, and control wiring.
Caution! Before connecting the
loads to the control unit, test the
loads for short-circuits.
1.Turn power OFF at the circuit breaker or
fuse box.
2.Connect a standard light switch between
the live lead and load wire to test the
circuit.
3.Turn power ON and check for short or
open circuits. If load does not operate,
the circuit is open. If the breaker/MCB
trips (fuse blows or opens), a load short
may exist. Correct short or open circuits
and test again.
Caution! Do not connect line
voltage/mains cable to Class 2 /
PELV terminals.
• Earth/ground terminal connection must
be made as shown in wiring diagrams.
• Do not mix different load types on the
same zone.
• Follow all local and national electrical
codes when installing Class 2 / PELV
wiring with line voltage/mains wiring.
• Test for short-circuits on loads before
wiring QS control unit.
To connect the line voltage/mains
cables to the control unit:
1.Strip 8 mm (5/16 in.) of insulation off the
line voltage/mains cables in the wallbox.
2.Connect the line voltage/mains, ground,
and load wires to the appropriate
terminals on the back of the control unit.
The recommended installation torque is
0,6 N•m (5,0 in.-lbs.) for line
voltage/mains connections and 0,6 N•m
(5,0 in.-lbs.) for the earth/ground
connection.
3/8 in. (10 mm)
8 mm
(5/16 in.)
Danger! GRAFIK Eye QS control units must be installed by a qualified electrician
in accordance with all applicable regulations and building codes. Improper
wiring can result in personal injury or damage to control units or other
equipment. Always turn off circuit breaker or remove main fuse from power line
before doing any work. To avoid overheating and possible damage to
equipment, do not install dimming devices to dim receptacles, motor-operated
appliances, or fluorescent lighting not equipped with Lutron Hi-lume®, Eco-10TM,
or Tu-Wire® electronic dimming ballasts, or devices approved for your location.
In dimmed magnetic low-voltage circuits, you can prevent transformer
overheating and failure by avoiding excessively high current flow: Do not operate
control units with any lamps removed or burned out; replace any burned out
lamps immediately; use only transformers that incorporate thermal protection or
fused primary windings. Control units are designed for residential and
commercial use, for indoor use only.
Neutral
Hot/Live
Switch
Load
Occupant Sensor Wiring
R
GRAFIK Eye® QS System Installation and Operation Guide 4
1234
1: COM
2: 24 V
3: MUX
4: MUX
12
ABC
Note: Use appropriate wire connecting devices as
specified by local codes.
Occupant
sensor
123456LN
Distribution Panel
LN
To Load 1
To Load 2
To Load 3
To Load 4
To Load 5
To Load 6
Control Wiring
Wiring the GRAFIK Eye® QS System
Class 2 / PELV USA Cable
IR Wiring
From external
IR connection
(by others)
Common and power (terminals 1 and 2):
Two 1,0 mm
2
(#18 AWG) each terminal
1,0 mm
2
(#18 AWG)
each terminal
2,5 mm
2
(#12 AWG)
each terminal
1234
12
ABC
123456LN
1,0 mm2(#18 AWG)
each terminal
230 V
1: IR DATA
2: IR COM
A: OCC SIG
B: 24 V
C: OCC COM
To control stations,
window treatments, or
other GRAFIK Eye QS
control units
Line Voltage/Mains Cables
and Load Wiring
Data (terminals 3 and 4):
Twisted, shielded pair 1,0 mm2(#22 AWG)
each terminal
R
GRAFIK Eye® QS System Installation and Operation Guide 5
• System communication uses Class 2 /
PELV low-voltage wiring.
• Follow all local and national electrical
codes when installing Class 2 / PELV
wiring with line voltage/mains wiring.
• Each terminal accepts up to two 1,0 mm
2
(#18 AWG) wires.
• Total length of control link must not
exceed 610 m (2 000 ft.).
• Make all connections in the control unit’s
wallbox.
• A QS system can have up to 100 zones
and 100 devices (see table below).
• Wiring can be T-tapped or daisy-chained.
• Wire sizes:
- Two 1,0 mm2(#18 AWG) conductors for
control power.
- One twisted, shielded pair of 1,0 mm
2
(#22 AWG) for data link.
- Cable is available from Lutron:
GRX-CBL-S-500 (non-plenum)
GRX-CBLP-S-500 (plenum rated).
Check compatibility in your area.
LUTRON
LUTRON
LUTRON
LUTRONLUTRON
LUTRON
LUTRON
GRAFIK Eye QS
Sivoia QS
seeTouch QS
LUTRON
LUTRON
LUTRON
LUTRON LUTRON LUTRON
LUTRON
Daisy-Chain Wiring Example
T-Tap Wiring Example
GRAFIK Eye QS
Sivoia QS
QS smart
power
supply panel
QS smart power
supply panel
seeTouch QS
QS System Low-Voltage Control Wiring
System Limits
QS Device Zone Count Device Count
3-zone QS 3 1
4-zone QS 4 1
6-zone QS 6 1
seeTouch
QS 0 1
Sivoia
QS 1 1
QS smart power supply panel 0 1
LUTRON
LUTRON
LUTRON
LUTRON
QS System Low-Voltage Terminal Connections
R
GRAFIK Eye® QS System Installation and Operation Guide 6
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
1234
12
ABC
123456HN
1234
12
ABC
123456HN
1234
12
ABC
123456HN
1234
12
ABC
123456HN
A1
2
3
4
1
A2
A3
A1 powers wallstation 1 only; terminal
2 terminates at wallstation 1
A2 and A3
have their
own power
supply; no
terminal 2
connection
A3 powers
wallstations 2,
3, and 4
A4
P1
S1
A4 powers wallstations
5, 6, and 7
P1 powers
shade S1
only
Sivoia QS
shade
QS smart
power supply
panel
Control units shown in rear view
5
6
7
• Connect the terminal 1, 3, and 4
connections to all control units,
wallstations, and control interfaces.
• Each control unit has its own power
supply. Terminate the terminal 2
connection (24 V power) so that each
control unit supplies power to a
maximum of three wallstations. Each
wallstation should receive power from
only one control unit.
No terminal 2
connection between
wallstations 4 and 5;
they are powered by
different control units
R
GRAFIK Eye® QS System Installation and Operation Guide 7
Installing the GRAFIK Eye® QS System
1.Mount a 89 mm (3 1/2-in.) deep
4-gang wallbox on a dry, flat indoor
surface that is accessible and allows
for system programming and
operation. Allow at least 110 mm
(4 1/2 in.) clearance above and below
the faceplate to ensure proper heat
dissipation. Allow 25 mm (1 in.) for
faceplate overhang on all sides.
Note: 4-gang wallbox available from
Lutron; P/N 241400.
2.Mount the control unit in the wallbox
as shown using the four screws
provided.
Note: Follow all local and national
electrical codes when installing Class
2 PELV wiring with line voltage/mains
wiring.
3.Apply the protective overlay to the
control unit. See page 14 for
instructions for naming zones.
Test the Wiring
1.Restore power.
2.Press the top button on the lighting
keypad. The LED will light.
3.Press the zone raise or lower button.
Make sure the control unit is dimming all
connected loads.
Protective overlay
(apply after installation)
Note: When tightening mounting
screws, make sure that the hinged
cover and faceplate will open fully,
as shown.
Wall
200 mm
(7.9 in.)
87 mm
(3.5 in.)
95 mm
(3.75 in.)
LUTRON
LUTRON
Faceplate overhangs
wallbox on all sides;
allow 25 mm (1 in.)
110 mm
(4.5 in.)
Zone Setup
Assign Load Type
1. Enter programming mode (see page 12).
2. Use the master buttons to highlight “Zone
setup” and press the OK button to
accept.
3. Use the master buttons to highlight “Load
type”. Press the OK button to accept.
4. Use the zone raise/lower buttons to
choose the load type for that zone. See
the list below for supported load types.
Press the OK button to accept.
5. The info screen will display a
confirmation screen that your load type
has been saved.
6. Exit programming mode (see page 12).
R
GRAFIK Eye® QS System Installation and Operation Guide 8
Main menu
Occ sensor
Zone setup
Zone setup
High end
Load type
Set type using
zone controls
Load type
OK
1 2 3 4 5 6
Use the
zone
raise/lower
buttons to
choose the
load type for
that zone.
Master
buttons
OK
button
Load Type Notes
• All electronic low-voltage (ELV) lighting
used with an interface must be rated for
reverse phase control dimming. Before
installing an ELV light source, verify with
the manufacturer that their transformer
can be dimmed. When dimming, an ELV
interface must be used with the control
unit.
• Not all zones must be connected;
however, connected zones must have a
minimum load of 40 W.
• No zone may be loaded with more than
500 W.
• Maximum total lighting load per unit is
10 A.
• Maximum total lighting load for a
magnetic low-voltage (MLV) load is
2 300 VA or 1 800 W after transformer.
Maximum load per MLV zone is 500 VA or
400 W.
Setting Load Types
Fixture load type
Incandescent
MLV (magnetic low-voltage)
ELV (electronic low-voltage)
Hi-Lume/Eco-10
Non-dim
Neon/Cold cathode
Tu-Wire
Direct control via
GRAFIK Eye QS
Incandescent
MLV
--
-Non-dim LOFO or Non-dim FOFO
Neon, CC
Tu-Wire
Control via
power module
Power module
Power module
Power module
Fluorescent module
Non-dim LOFO or Non-dim FOFO
Neon, CC
Tu-Wire
LUTRON
LUTRON
Choose this load type from the menu
on the GRAFIK Eye® QS:
Saved
Saved
Set Minimum Level (optional)
Some local regulations specify a
minimum lighting level for dimming
zones in occupied buildings. If this
pertains to you, follow these steps to
set up your minimum lighting level.
1. Enter programming mode (see page 12)
and select “Zone setup,” then “Min
level”. Press the OK button to accept.
2. Use the master buttons to highlight
“OFF” if you want your lights to go all
the way off at their minimum light level,
or “10%” if you want that to be the
minimum light level. Press the OK button
to accept.
Note: Non-dim loads will turn off
regardless of the minimum level setting.
3. The info screen will display a
confirmation screen that your minimum
level has been saved.
4. Exit programming mode (see page 12).
R
GRAFIK Eye® QS System Installation and Operation Guide 9
Zone Setup
Set High End or Low End
High and low end trim settings limit the
maximum and minimum output of a
dimming zone. Trim levels are set
automatically when the load type is
programmed. Change the high or low
end trim for a zone only if the default
setting needs to be adjusted.
1. Enter programming mode (see page 12).
2. Use the master buttons to highlight “Zone
setup” and press the OK button to
accept.
3. Use the master buttons to highlight “High
end” or “Low end” (this example shows
low end). Press the OK button to accept.
4. Use the zone raise/lower buttons to set
the high end or low end trim for that
zone.
The info screen will display each zone
number and percentage as you adjust it.
Press the OK button to accept.
5. The info screen will display a
confirmation screen that your setting has
been saved.
6. Exit programming mode (see page 12).
Main menu
Occ sensor
Zone setup
Zone setup
High end
Low end
Set trim using
zone controls
Zone 2
Low end
OK
1 2 3 4 5 6
Use the
zone
raise/lower
buttons to
set the high
end or low
end trim for
that zone.
Master
buttons
OK
button
10%
Min level
OFF
Zone setup
Low end
Min level
Saved
Saved
Saved
Saved
Preprogrammed Button Functionality
R
GRAFIK Eye® QS System Installation and Operation Guide 10
Lighting Column Button Preprogramming
(Factory Default: Dimmable Loads)
Scene 1: All lights to 100%
Scene 2: All lights to 75%
Scene 3: All lights to 50%
Scene 4: All lights to 25%
Scene OFF: All lights to 0%
Lighting Column Button Preprogramming
(Factory Default: Non-Dim Loads)
Scene 1: All lights On
Scene 2: All lights On
Scene 3: All lights On
Scene 4: All lights On
Scene OFF: All lights Off
Shade Column Button Preprogramming
(Factory Default: Sivoia® QS shades)
All shades fully open
All shades to 50%
All shades fully closed
Lower/Raise all shades
The GRAFIK Eye® QS System controls lights without special programming. The factory
defaults for the lighting column buttons are shown below for both dimmable and nondim zones. See pages 15 through 17 for methods for changing scene settings.
The info screen goes blank after 20
seconds if there is no button press or
fading.
The master buttons also activate the info
screen. These buttons temporarily raise or
lower all dimmable lights (except those
programmed as unaffected in the current
scene). Adjustments are temporary and do
not affect scene programming.
The OK button activates the info screen,
which then shows the current scene and its
fade time.
The timeclock button activates the info
screen and displays the current time, the
next event scheduled to occur, and what
that next event is. Pressing a second time
displays the location and the
sunrise/sunset times.
R
GRAFIK Eye® QS System Installation and Operation Guide 11
OK
Info screen: see example screens below
Timeclock button displays the current
time and the next scheduled event.
Pressing when in Program mode
functions as a
“back” button.
OK button activates the info screen,
which shows the current scene’s fade
time. In Save Always mode, allows fade
time adjustment. In
Save by OK
mode, pressing
a second time
allows zone
adjustment;
pressing a third
time allows fade
adjustment.
Master buttons temporarily raise or lower
all lights (except unaffected, shades, and
non-dim zones) on this GRAFIK Eye QS
unit
Scene 1
Master raise
Master lower
General Functionality
OK
Scene: 1
Adjust fade
03 seconds
11:23 AM Fri
Next: 5:00 PM
Scene 1
Loading...