Lutron EA RMKS-CCO1-24-B Installation Instructions

PowPak | Installation

CCO Module

Part of the Vive Family

RMKS-CCO1-24-B

Note for Replacement:

RMxS - the "S" model can replace the non-"S" model

Important Notes: Please read before installing.

• For installation by a qualified electrician in accordance with all local and national
electrical codes.

• Note: Use copper conductors only.

• The 24 V~ or 24 V- supply and load shall be provided via an approved power

source in accordance with IEC/EN61558-2-6.

• Check to see that the device type and rating is suitable for the application.

• DO NOT install if product has any visible damage.

• If moisture or condensation is evident, allow the product to dry completely

before installation.

• Operate between 0 °C and 55 °C.

• 0% to 90% humidity, non-condensing.

• For indoor use only.

WARNING

Shock Hazard. May result in serious injury or death.

Turn off power at circuit breaker before installing the unit.

24 V~ 45 mA
24 V- 35 mA

PowPak

CCO Module

Install in center of room to

maximize RF coverage.

Radio Powr Savr

Occupancy Sensor

Required Components

For each system ensure you have:

041607
Rev. A
10/2017

At least one PowPak CCO Module

Load
Status
LED

Contact
Closure
Output
(CCO)
(Class 2)

Start Here

1

B The PowPak CCO Module can be installed in a junction box or

CCO Toggle

Advanced
Operations

+

PowPak CCO Module

Install PowPak CCO Module

Suggested Installation Location: Center of room to ensure
proper RF coverage of area.

A

Install the 1/2 in NPT to 20 mm conduit adapter (provided) onto the
PowPak CCO Module (optional).

marshalling box using the conduit nut (provided) or with mounting
screws (not provided). Please consult local and national electric codes
for proper installation.

C

Once installed, energize the PowPak CCO Module.

D

Use the CCO Toggle button to toggle between high-end and OFF to

verify wiring.

At least one Wireless Transmitter

Radio Powr Savr Occupancy Sensor
(10 maximum)

Supply Voltage
24 V~ / 24 V-

Note: CCO Module

supply wires can be
connected in any
polarity.

Wiring a Lever
Operated Connector

When wiring lever operated
connectors (2 supplied) use

2.5 mm2 to 4.0 mm2
(14 AWG to 12 AWG) solid
or stranded copper wire.

10 mm

2

Black

Black

1

3

Customer Assistance www.lutron.com/support

Cal.

Link

Test

Pico Remote
Control
(10 maximum)

To CCO-controlled device

Note: When wiring CCO output, use 0.5 mm2 to 1.5 mm2

(20 AWG to 16 AWG) solid or stranded wire.

Radio Powr Savr
Daylight Sensor
(1 maximum)

COM (Common)
NO (Normally Open)
NC (Normally Closed)

Conduit Nut

(optional)

1/2 in NPT to
20 mm Conduit
Adapter

(optional)

CCO Information

• This product features a single contact closure output with both
normally open (NO) and normally closed (NC) dry contacts.

• The CCO incorporates maintained output behavior only.

• The CCO is rated to switch resistive loads at

voltages up to 24 V only. To properly control
inductive load types such as relays, solenoids,
or motors, refer to Application Note #434.

Transmitting Device Transmitted Command CCO Default Action

Pico
Remote Control

Radio Powr Savr
Occupancy Sensor

Radio Powr Savr
Vacancy Sensor

Radio Powr Savr
Daylight Sensor

On NO = Close, NC = Open

Off NO = Open, NC = Close

Raise NO = Close, NC = Open

Lower No Action

Preset NO = Close, NC = Open

Occupied NO = Close, NC = Open

Unoccupied NO = Open, NC = Close

Occupied No Action

Unoccupied NO = Open, NC = Close

Ambient light below target
level

Ambient light above target
level

Switching

Resistive

Voltage

Load

0-24 V-

1.0 A

0-24 V~

0.5 A

NO = Close, NC = Open

NO = Open, NC = Close

R

Unaffected Mode

Unaffected Mode allows a system with an Occupancy Sensor
associated to multiple CCO Modules to be set up such that only
selected loads turn on automatically. Other loads will require a manual
turn-on with a Pico Remote Control. All loads will turn off automatically
when the room is vacated.

A

On a CCO Module, press and hold both the CCO Toggle and
Advanced Operations (“ADV”) buttons for 6seconds until the LED
begins flashing quickly.

B

On the associated Occupancy Sensor, press and hold the “Test”
button* for 6 seconds until the lens flashes.

C

Unaffected mode will be exited automatically. This CCO Module will
now be unaffected by occupancy commands. Repeat procedure
for any additional devices.

* If no “Test” button, hold “Lights On” button.

English

9 m

Maximum

Pico
Remote
Control

12 m

10 m

2

Programming with a Vive Hub

A

Use an iOS or Android

compatible device.

Vive

X

B

Download the Lutron

Vive app.

C

Open the app and follow the

instructions.

All Wireless Transmitters must be installed within
9 m of the PowPak CCO Module.

PowPak | Programming Without a Vive Hub

1

Associate Wireless Transmitters to PowPak CCO Module

Before beginning this step, make sure that there are no other PowPak modules being set up within the same building. It is possible that Wireless Transmitters from
other systems can be incorrectly associated to this system.

A Hold the CCO Toggle

button on the PowPak
CCO Module for 6 seconds
to enter association mode.

Note: The CCO will open
and close once after each
step to confirm successful
completion.

CCO
Toggle

Advanced
Operations

B Hold the indicated button

on a Wireless Transmitter
for 6 seconds to
associate the device.*
Repeat for any additional
Wireless Transmitters.

* If no g button, hold

“Lights Off” button.

Link

C Hold the CCO Toggle button on the

PowPak CCO Module for 6 seconds
to save association(s).

D Permanently install wireless transmitters

(consult individual component installation
guides for information).

Cal.

Test

Reset Factory Defaults

Note: In some instances it may be necessary to reset the PowPak

Note: For further information on set up, programming,

and troubleshooting with a Vive system, please refer to the
installation instructions included with the Vive hub or visit
www.lutron.com/vive-europe

vive.lutron.com

X

Note: For programming the PowPak CCO Module without a Vive

hub see Programming Without a Vive Hub below.

CCO Module back to factory default settings.

A

Triple-tap the Advanced Operations (“ADV”) button on the CCO
Module and hold until the LED begins to flash slowly.

B

Within 3 seconds of flashing, release and triple-tap the button again
and the LED will flash rapidly indicating that the unit has been reset
to factory defaults.

Note: Any associations or programming previously set up with the

unit will be lost and will need to be re-programmed.

Troubleshooting www.lutron.com / vive

2

Calibrate the Radio Powr Savr
Daylight Sensor

Daylight Sensor will control all wired fixtures equally.

A

Press and release the “Cal” button on the

Daylight Sensor.

B

Turn lights in room on using the CCO Toggle

button on the PowPak CCO Module or an
associated Pico wireless control.

C

Press and hold the “Cal.” button for 6seconds.

D

Exit room for 5 minutes to allow calibration to be completed.

Note: When calibration has completed, all lights will flash and

begin to respond to daylight.

CCO­controlled
device does
not respond
to Wireless
Transmitter(s)

Wireless
Transmitter(s)
cannot be
associated to
PowPak CCO
Module

Hereby, Lutron Electronics Co. Inc declares that the radio equipment type
RMKS-CCO1-24-B is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following
internet address: lutron.com/cedoc

Cal.

Link

Test

Limited Warranty:
www.lutron.com/en-US/ResourceLibrary/warranty/Limited%20Comm.pdf

Customer Assistance:

Europe: +44.(0)20.7680.4481
Others: +1.610.282.3800
www.lutron.com/support

• Ensure breaker to the PowPak CCO Module is on.

• Ensure the CCO-controlled device has been
properly wired to the PowPak CCO Module.

• Ensure Wireless Transmitter is properly associated
to PowPak CCO Module.

• Ensure Wireless Transmitter’s battery is installed
correctly.

• The maximum number of Wireless Transmitters
have been associated to the PowPak CCO
Module. To remove a previously set up Wireless
Transmitter, tap the button used for association on
the Wireless Transmitter three times, on the third
tap hold for three seconds and then tap three more
times.

Lutron EA Ltd | 125 Finsbury Pavement, 4th floor
London EC2A 1NQ, UK

Lutron, Pico, and PowPak are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc. App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Android, Google Play and the Google Play logo are trademarks of Google Inc. ©2013 – 2017 Lutron Electronics Co., Inc.