PowPak | Installation
Relay Module
Part of the Vive Family
RMKS-16R-DV-B
With Softswitch
RMKS-5R-DV-B
Note for Replacement:
RMxS - the "S" model can replace the non-"S" model
Important Notes: Please read before installing.
• For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 0 °C and 55 °C.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
Shock Hazard. May result in serious injury or death.
WARNING
English
Turn off power at circuit breaker before installing the unit.
Relay Module
Install in center of room to
maximize RF coverage.
9 m
Maximum
Pico
Remote
Control
All Wireless Transmitters must be installed within
9 m of the PowPak Relay Module.
220 – 240 V~ 50 / 60 Hz 16 A
6 A Motor at 220 – 240 V~
220 – 240 V~ 50 / 60 Hz 5 A
PowPak
Radio Powr Savr
Occupancy
Sensor
12 m
10 m
041608
Rev. A
10/2017
For each system ensure you have:
At least one PowPak Relay Module
Load
Status
LED
220 - 240 V~
Relay Toggle
Advanced
Operations
+
PowPak Relay Module
Start Here
1
Install PowPak Relay Module
Suggested Installation Location: Center of room to ensure
proper RF coverage of area.
A
Install the 1/2 in NPT to 20 mm conduit adapter (provided) onto the
PowPak Relay Module.
B The PowPak Relay Module can be installed in a junction box or
marshalling box using the conduit nut (provided) or with mounting
screws (not provided). Please consult local and national electric codes
for proper installation.
C
Once installed, energize the PowPak Relay Module.
D
Use the Relay Toggle button to toggle between high-end and OFF to
verify wiring.
2
Programming with a Vive Hub
A
Use and iOS or Android
compatible device.
Vive
X
B
Download the Lutron
Vive app.
At least one Wireless Transmitter
Radio Powr Savr Occupancy Sensor
(10 maximum)
Wiring a Lever
Operated Connector
When wiring lever operated
connectors (2 supplied) use
2.5 mm2 to 4.0 mm2
(14 AWG to 12 AWG) solid
or stranded copper wire.
10 mm
C
Open the app and follow the
instructions.
PowPak | Programming Without a Vive Hub
1
Associate Wireless Transmitters to PowPak Relay Module
Before beginning this step, make sure that there are no other PowPak modules being set up within the same building. It is possible that Wireless Transmitters from
other systems can be incorrectly associated to this system.
Required Components
A Hold the Relay Toggle button on
the PowPak Relay Module for
6 seconds to enter association
mode.
Note: The load will flash
once after each step
to confirm successful
completion.
220 - 240 V~
Relay
Toggle
Advanced
Operations
B Hold the indicated button
on a Wireless Transmitter
for 6 seconds to
associate the device.*
Repeat for any additional
Wireless Transmitters.
* If no g button, hold
“Lights Off” button.
Link
C Hold the Relay Toggle button on the PowPak
Relay Module for 6 seconds to save
association(s).
D Permanently install wireless transmitters
(consult individual component installation
guides for information).
Cal.
Test
Customer Assistance www.lutron.com/support
Unaffected Mode
Unaffected Mode allows a system with an Occupancy Sensor
associated to multiple Relay Modules to be set up such that only
selected loads turn on automatically. Other loads will require a
manual turn-on with a Pico Remote Control. All loads will turn off
automatically when the room is vacated.
A
Cal.
Link
Test
Pico Remote
Control
(10 maximum)
Line/Hot
(Brown)
Neutral
(Blue)
1
3
2
Switched
Line/Hot (Black)
Neutral (Blue)
To Load
Radio Powr Savr
Daylight Sensor
(1 maximum)
Conduit Nut
1/2 in NPT to
20 mm Conduit
Adapter
Note: For further information on set up, programming, and troubleshooting
with a Vive system, please refer to the installation instructions included with
the Vive hub or visit www.lutron.com/vive-europe
Note: For programming the PowPak Relay Module without a Vive hub see
vive.lutron.com
X
Programming Without a Vive Hub below.
2
Calibrate the Radio Powr Savr
Daylight Sensor
Daylight Sensor will control all wired fixtures equally.
A
Press and release the “Cal.” button on the
Daylight Sensor.
B
Turn lights in room on using the Relay Toggle
button on the PowPak Relay Module or an
associated Pico wireless control.
C
Press and hold the “Cal.” button for 6seconds.
D
Exit room for 5 minutes to allow calibration to be completed.
Note: When calibration has completed, all lights will flash and
begin to respond to daylight.
Cal.
Link
Test
On a Relay Module, press and hold both the Relay Toggle and
Advanced Operations (“ADV”) buttons for 6seconds until the
LED begins flashing quickly.
B
On the associated Occupancy Sensor, press and hold the
“Test” button* for 6 seconds until the lens flashes.
C
Unaffected mode will be exited automatically. This Relay
Module will now be unaffected by occupancy commands.
Repeat procedure for any additional devices.
* If no “Test” button, hold “Lights On” button.
Reset Factory Defaults
Note: In some instances it may be necessary to reset the
PowPak Relay Module back to factory default settings.
A
Triple-tap the
Relay Module and hold until the LED begins to flash slowly.
B
Within 3 seconds of flashing, release and triple-tap the button
again and the LED will flash rapidly indicating that the unit has
been reset to factory defaults.
Note: Any associations or programming previously set up with
the unit will be lost and will need to be re-programmed.
Advanced Operations (“ADV”)
button on the
Troubleshooting www.lutron.com / vive
Load does
not respond
to Wireless
Transmitter(s)
Wireless
Transmitter(s)
cannot be
associated to
PowPak Relay
Module
Hereby, Lutron Electronics Co. Inc declares that the radio equipment
type RMKS-16R-DV-B and RMKS-5R-DV-B are in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address: lutron.com/cedoc
Limited Warranty:
www.lutron.com/en-US/ResourceLibrary/warranty/Limited%20Comm.pdf
Customer Assistance:
Europe: +44.(0)20.7680.4481
Others: +1.610.282.3800
www.lutron.com/support
• Ensure breaker to the PowPak Relay Module
is on.
• Ensure the load has been properly wired to the
PowPak Relay Module.
• Ensure Wireless Transmitter is properly
associated to PowPak Relay Module.
• Ensure Wireless Transmitter’s battery is installed
correctly.
• The maximum number of Wireless Transmitters
have been associated to the PowPak Relay
Module. To remove a previously set up Wireless
Transmitter, tap the button used for association
on the Wireless Transmitter three times, on the
third tap hold for three seconds and then tap
three more times.
Lutron EA Ltd | 125 Finsbury Pavement, 4th floor
London EC2A 1NQ, UK
Lutron, Pico, PowPak, and Softswitch are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc. App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Android, Google Play and the Google Play logo are trademarks of Google Inc. ©2013 – 2017 Lutron Electronics Co., Inc.
Loading...