Page 1
Installation Instructions
Please Read Before Installing
Overview
Color Change Kits allow for changing the color of an
existing RadioRA-SR, RadioRA, or HomeWorks dimmer,
switch, or fan speed control.
ENGLISH
Important Notes
Environment: Ambient operating temperature:
32 °F to 104 °F (0 °C to 40 °C), 0-90% humidity, noncondensing. Indoor use only.
Wallplates: Do not paint controls, Color Change Kits,
or wallplates.
Cleaning: To clean, wipe with a clean damp cloth.
DO NOT use any chemical cleaning solutions.
Models Supported: The Color Change Kits may ONLY
be used with the RadioRA-SR, RadioRA, and HomeWorks
model numbers listed in Table 1.
Warranty: For Warranty information, please see the
enclosed Warranty, or visit www.lutron.com/resiinfo
Lutron® Color Change Kits
Compatible with RadioRA®-SR, RadioRA and HomeWorks®
RK-D-, RK-F-, RK-AD-, RK-S-, RK-AS-
RK-D-
Dimmer
RK-F-
Fan Speed
Control
RadioRA-
SR RadioRA
SRD-6D,
SRD-10D,
SRD-10ND
SRD-2ANF — HRD-2ANF HWD-2ANF RK-F
SD-RD RA-AD HD-RD HD-RD RK-AD
SRD-8ANS RA-8ANS HRD-8ANS HWD-8ANS RK-S
SD-RS RA-AS HD-RS HD-RS RK-AS
RA-6D,
RA-6ND,
RA-10D
Table 1
RK-AD-
Accessory
RK-S-
Switch
Dimmer
HomeWorks RFHomeWorks
HRD-6D,
HRD-6ND,
HRD-10D,
HRD-10ND
Wired
HWD-6D,
HWD-6ND,
HWD-10D,
HWD-10ND
RK-AS-
Accessory
Switch
Color
Change Kit
RK-D
Installation
1. Turn power off at circuit breaker or remove fuse.
WARNING - To avoid the risk of electric shock,
locate and lock supply breaker in the OFF position
before proceeding. Failure to do so could result in
death or serious injury.
2. Remove Wallplate and Adapter. See Figure 1.
Adapter Wallplate
Figure 1
3. Remove existing Color Change Kit. Unclip the existing kit
by pressing in on both top clips with thumb and
forefinger. Repeat for bottom clips. Pull the kit straight
out from the control, being careful not to dislodge the
clear plastic frame underneath. See Figure 2.
Clear Plastic
Frame
Clips
Front Accessible
Figure 2
Lutron Elec tron ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and print ed in the U.S.A. 5/09 P/N 044-105 Rev. D
Service Switch (FASSTM)
Note: If the clear plastic frame gets dislodged or lost, a
spare frame is provided with the kit. Follow the instructions
below:
a. Holding the frame with the hook on the left, hook the
frame into the hole next to the center LED pipe.
b. Press firmly on the frame at the hook. When properly
seated, the frame will snap into place. See Figure 3.
LED
Hook
Figure 3
pipes
Attach here
4. Install new Color Change Kit. Push the kit straight onto
the control, being careful not to dislodge the clear plastic
frame underneath. Press firmly on each clip to lock into
place. See Figure 2.
5. Check control operation. If any of the buttons on the control feel stiff or do not operate, repeat steps 3 and 4.
6. Install Adapter and Wallplate. See Figure 1.
7. Turn power on at circuit breaker or replace fuse.
8. Check FASS operation. Pull the FASS
(see Figure 2) in and out several times and ensure that
power is removed and restored to the load.
This product may be covered by one or more of the following U.S. patents: 7,365,282 and
corresponding foreign patents. Lutron, HomeWorks, RadioRA and the sunburst logo are
registered trademarks and FASS is a trademark of Lutron Electronics Co., Inc.
©2009 Lutron Electronics Co., Inc.
Loading...