Lutron QSWS2-3BRLI-WH Installation Manual

Wallstation
Installation Guide

Please Read

Low-Voltage PELV (Class 2: USA)

24 V 30 mA

 QSWS2-1B
 QSWS2-2B
 QSWS2-3B
 QSWS2-5B
 QSWS2-7B
 QSWS2-2BRL
 QSWS2-3BRL
 QSWS2-5BRL
 QSWS2-2BRLIR
 QSWS2-3BRLIR
 QSWS2-5BRLIR
 QSWS2-1RLD
 QSWS2-2RLD
 QSWS2-3BD

R

Wallstation circuits are classified as Class 2 circuits
(USA) and PELV circuits (IEC). As Class 2 circuits,
they comply with the requirements of NFPA® 70,
National Electrical Code® (NEC®). As PELV circuits,
they comply with the requirements of IEC 60364-4­41, VDE 0100 Part 410, BS7671:1992, and other
equivalent standards. When installing and wiring to
these wallstations, follow all applicable national and/or
local wiring regulations. External circuits connected to
input, output, and other communication terminals of
wallstations must be supplied from a listed Class 2
source or comply with the requirements for PELV
circuits, as applicable in your country.

CAUTION!

• Read all instructions carefully before starting
installation.

• Lutron recommends that wallstations be installed
by a qualified electrician.

• Do not connect high-voltage power to low-voltage
terminals. Improper wiring can result in personal
injury or damage to the control or to other
equipment.

• Use only a cloth with warm water and mild soap to
clean faceplates (no chemical cleaners).

Wiring Notes

• System Maximums
— GRAFIK Eye® QS series control units can

each power a maximum of 3 wallstations.
— 2000 ft. (610 m) maximum wiring length
— 32-104 °F (0-40 °C) operating temperature.
— 100 devices per link (seeTouch

® QS, Sivoia®

QS, power panel, and GRAFIK Eye QS each

count as one device); 100 zones maximum

per link

• Refer to the system installation guide and Lutron
job drawings for power cable and data cable
(control link) wiring restrictions and limitations.

• Control Link Wiring

— Power: Two #18 AWG (1.0 mm

2

) PELV (Class

2: USA) wires. Connect to terminals 1 and 2.

— Data: Two shielded #22 AWG (1.0 mm

2

)
PELV (Class 2: USA) wires (twisted, shielded
pair). Connect to terminals 3 and 4.

Lutron offers a one-cable, non-plenum, low­voltage solution (P/N GRX-CBL-346S-500),
and a one-cable, plenum, low-voltage
solution (P/N GRX-PCBL-346S-500). Check
availability outside the U.S.

• Sensor/Contact Closure Input Connector Wiring
(optional):

— Three #18 AWG (1.0 mm2) PELV (Class 2:

USA) wires.

• Connect the wallstation to the control link inside
the wallstation’s wallbox or in a junction box
(provided by others).

• Control link wiring must not be run in the same
raceway as line voltage.

• Control link wiring is not to exceed 2000 ft. (610 m).

• The drain/shield wire must be maintained
throughout the control link. Do not connect the
shield to earth/ground or allow contact with the
grounded wallbox.

Installation Instructions Occupant Copy2

Occupant Copy Installation Instructions3

Installation

Warning! Always turn OFF the circuit

breaker/MCB or remove the main fuse from
the power line before doing any work.
Failure to do so can result in serious
personal injury.

1. Turn Power OFF. Turn power OFF at circuit
breaker/MCB (or remove fuse).

2. Mount Wallbox. Mount standard U.S. 1-gang
wallbox, 2.75 in. (70 mm) deep (available from
Lutron; P/N 241-519). Check availability outside
the U.S.

3. Prepare Wallstations. Remove the faceplate and
set aside.

4. Prepare wires. Strip insulation from wires so that
3/8 in. (9.5 mm) of bare wire is exposed.

Each wallstation terminal accepts up to two
#18 AWG (1.0 mm

2

) wires.

Note: Wiring may be done in a daisy-chain or

T-tap configuration, as shown below.

3/8 in. (9.5 mm)

Daisy chain

T- Tap

ON

OFF

ON

OFF

ON

OFF

1 2 3 4 5 6

LUTRON

LUTRONLUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRON

LUTRON

Installation Instructions Occupant Copy4

5. Connect the Wallstation to the Control Link.
Connect two #22 (1.0 mm

2

) shielded, twisted pair wires
to terminals 3 and 4 of the wallstation’s control link
connector. Shielding (drain) of the twisted pair wires
must be connected together as shown, but do not
connect the shielding to earth/ground or the wallstation
or allow contact with the grounded wallbox.

Note: Use the wire connector required by local code

(those shown are common in the US).

4

3

2

1

C

B

A

Drain

Data link: (1) twisted,
shielded pair
#22 AWG (1.0 mm

2

)

3: MUX
4: MUX

2 #18 AWG
(1.0 mm

2

)

2 #18 AWG
(1.0 mm2)

PELV (Class 2: USA)
control wiring
(2) #18 AWG (1.0 mm

2

)
1: Common
2: 24 V

Control Link Wiring

9

6. Connect the Wallstation to external contact
closure inputs (optional). If using one contact

closure input, connect the input to terminal A of
the wallstation sensor/contact closure input
connector. If using two contact closure inputs,
connect the inputs to terminals A and B. Connect
the common side of the contact closure inputs to
terminal C.

Contact Closure Input Wiring

Notes for Contact Closure Inputs:

Verify compatibility of external contact closure input
devices. The contact closure inputs can be used
with either dry contact closures or ground­referenced solid-state outputs. The outputs must
stay in the closed or open states for at least 40
msec in order to be recognized by the wallstation.
If there is any question as to whether the device is
compatible with these specifications, contact the
manufacturer.

Contact closure input function is determined by
the programming of the top and bottom buttons of
the wallstation.

Input 2

Common

(3) #18 AWG

(1.0 mm

2

)

Input 1

9

:

30 mA

COO P E R S BURG , PA 18036 US A

AC N

099 942

AC N

099

Occupant Copy Installation Instructions5

Typical Mounting Diagram

(Exploded View)

7. Mount Wallstation. Carefully mount and align the
wallstation as shown. Screw top and bottom
screw into the control and wallbox. Replace
faceplate, adapter (for insert versions), and button
assembly.

8. Turn Power ON. Turn ON control breaker, or

replace main fuse.

Notes

• Unprogrammed (out of the box) QS wallstations

and control units will all work together until they are
reprogrammed otherwise.

• LEDs on wallstation buttons light when the scene

programmed to it is the last scene activated.

Wallbox

Control

Mounting screws

Buttons

Adapter

Faceplate

Adapter screws

2. Select wallstation function (optional).
The info screen on the GRAFIK Eye QS control
unit will display a prompt to change your
wallstation’s function (type).

Press the OK button on the QS control unit to
display the current wallstation function/type. To
change, use the master buttons to scroll through
the available choices until the function you want
displays on the info screen.

The keypad menu will display only functions that
are available for the wallstation model that is
“talking” to it. The example shown here is for a 5­button wallstation with raise/lower buttons.

Press the OK button to accept and save your
highlighted choice.

6Installation Instructions Occupant Copy

System Communications

In order for wallstations to communicate with a
control unit, each wallstation must be individually
configured to “talk” to a “listening” control unit.
In order for shade wallstations to control
exclusively a given group of window treatments
(as opposed to all window treatments in the
system), each shade wallstation must be
individually configured to “talk” to its respective
window treatments.
(Only one wallstation can be in setup mode at a
time.)

1. Enter Setup Mode. Press and hold simultaneously
for 3 seconds the top and bottom buttons (not
including raise/lower buttons) on the wallstation. For
1-button wallstations, press and hold the single
button for 10 seconds. (LEDs will flash periodically.)

Note: For wallstations with two sets of

buttons, you will program each
set as if each were its own
wallstation. For multigroup shade
wallstations, first select the group,
then program the wallstation for
that group.

Press and hold the top and bottom buttons on your
wallstation for 3 seconds to enter setup mode.

Keypad

Change type?

Press OK

Master
buttons

OK
button

Change type?

01-04, off

Master
buttons

OK
button

OK

OK

3b.For wallstations with partition function:

2-button wallstations that control one partition:
The LEDs on the wallstation will alternately blink.
On each GRAFIK Eye QS control unit within the
partitioned space, press and hold the top button
on the lighting column until its LEDs flash in
unison. The control units will then function together
when the partition is open.

All other partition wallstations:

On the wallstation,
press the button you want to use to control
partition function. Its LED will blink slowly. Then, on
each GRAFIK Eye QS control unit that is related to
that partitioned space, press and hold the top
button on the lighting column until its LEDs flash in
unison.
For multiple partitions, repeat for additional buttons
on the partition wallstation, and the related control
units.

NNoottee::

To stop a control unit from “listening” to a
wallstation, put the wallstation in setup mode,
then press and hold for 3 seconds the

bboottttoomm
button on the lighting keypad of the control unit
you want to stop listening.

Proceed to Step 4.

7Occupant Copy Installation Instructions

Programming

The next step is to configure your wallstation
which GRAFIK Eye QS control unit or window
treatment “listens” when the wallstation
“talks”, depending on your wallstation’s
function. You will perform only one of Steps 3a
through 3e for each wallstation.

3a.For wallstations with scene, panic, or

sequence functions: Press and hold the top

button on the GRAFIK Eye QS control unit lighting
column until its LEDs flash in unison. Repeat for
each control unit you want to “listen” to the
wallstation for the selected function.

NNoottee::

To stop a control unit from “listening” to a
wallstation, put the wallstation in setup mode,
and press and hold for 3 seconds the

bboottttoomm
button on the lighting keypad of the control unit
you want to stop listening.

Proceed to Step 4.

Press and hold the top button on the lighting column
for 3 seconds to make control unit “listen”.

Press and hold the top button on the lighting column
for 3 seconds to make control unit “listen”.

Press and hold
for 3 seconds to
make control unit
stop “listening”.

1 2 3 4 5 6

1 2 3 4 5 6

OK

OK

1 2 3 4 5 6

OK

8Installation Instructions Occupant Copy

3c. For wallstations with fine tune function: On the

GRAFIK Eye QS control unit, press simultaneously the
raise and lower buttons for the zone you want the
wallstation to fine tune. Repeat for each zone you wish
to “listen” to the selected wallstation, or for zones on
additional control units. When listening, zone LEDs
flash. When unassigned (not “listening”), the 3 middle
zone LEDs light.

NNoottee::

To stop a zone from listening to a wallstation, put
the wallstation in setup mode, and press
simultaneously the raise and lower buttons on the
zone you want to stop listening.

Proceed to Step 4.

3d.For wallstations with zone function: On the

wallstation, press the button you want to program
to toggle (alternate between) zones. Its LED will
blink slowly.

On the GRAFIK Eye QS control unit, for the zone
you want to “listen” to the wallstation, use the raise and
lower buttons to set the desired levels. The LEDs will
indicate the level. Then, press simultaneously those
raise and lower buttons to listen that zone to the
wallstation. When listening, zone LEDs flash. When not
listening (unassigned), the 3 middle zone LEDs light.

Repeat for each zone you wish to assign to the
selected wallstation, or for zones on additional
control units.

Finally, repeat to program the remaining buttons
on the wallstation with their respective zones.

NNoottee::

To stop a zone from listening to a wallstation, put
the wallstation in setup mode, and press
simultaneously the raise and lower buttons on the
zone you want to stop listening.

Proceed to Step 4.

3e.For wallstations configured for shade

function:

Note: Entering setup mode will cause the window

treatments to move between their open and
close limits. Be sure that the open and close

limits have been set correctly (see page 12).
Because your wallstation is configured for shade
function, upon entering setup mode, EDUs
(electronic drive units of window treatments)
assigned to that wallstation will move to their close
limit, and EDUs not assigned to it will move to their
open limit.
To assign an EDU to the wallstation that is in setup
mode, use one of the following methods:

Either -Press the top button on the wallstation. Each

time you press the top button, a different EDU
that is assigned to that wallstation will open
and close in an 8-inch range. Press the top
button until the EDU you wish to assign to the
wallstation moves. (You can also use the
bottom button, which moves through the
EDUs in the opposite order.)
Assign or unassign the currently selected EDU
to the wallstation using the raise and lower
buttons:
The lower button assigns the selected EDU.
The raise button unassigns the selected EDU.

Press and hold the raise and lower
buttons for the zone you want to
listen or stop listening.

Lower button

(assign)

Raise button
(unasssign)

1 2 3 4 5 6

OK

9Occupant Copy Installation Instructions

Or -Press any button on an EDU to toggle

between unassignment and assignment for
that EDU’s window treatment to the

wallstation.
Check window treatment assignments: EDUs for
window treatments assigned to the wallstation will
be at their close limit, and EDUs for window
treatments not assigned to the wallstation will be
at their open limit.

Note: Once you have assigned window treatments

to a wallstation and exited setup mode, you

will notice the following additional functionality:

-When some or all EDUs assigned to a
wallstation are moving, press any button on the
wallstation to immediately stop all assigned
EDUs.

-The position that each EDU moves to when
any but the top or bottom button is pressed is
now programmable (see page 13).

-No matter how or from where their movement
is commanded, whenever all the assigned
EDUs come to a stop and match their
programmed positions for one of the buttons
on the wallstation, the LED next to that button
will automatically light.

Proceed to Step 4.

4. Exit Setup Mode. Press and hold the top and
bottom buttons on the wallstation simultaneously
for 3 seconds. For 1-button wallstations, press and
hold the single button for 10 seconds. The LEDs
will return to normal.

Press and hold the top and bottom buttons on your
wallstation for 3 seconds to exit setup mode.

10Installation Instructions Occupant Copy

SeeTouch® QS Wallstation
Button Functions

The following functions are menu choices when the
wallstation is in setup mode and the GRAFIK Eye QS
is displaying the keypad menu. Each function choice
is explained below. See the next page for a summary
table of wallstations and their function choices.

SScceenneess::

Choose from the list of preset groups of
scenes to assign to the buttons on this wallstation.
See the next page for a list of available scene
groupings for each keypad.

ZZoonnee::

Assigns control of one or more zones on one
or more GRAFIK Eye QS control units to the selected
wallstation button. Pressing a zone control button on
a wallstation causes all assigned zones to go to the
set level, with a fade time of 3 seconds (if all
assigned zones are currently off). If any assigned
zone is currently on (at any level), the LED for that
zone will be lit, and pressing the wallstation button
that controls that zone will cause all assigned zones
to fade to off over 3 seconds. The 3-second fade
time cannot be adjusted.

PPaarrttiittiioonn::

Used for rooms that can be divided by one
or more partitions into smaller spaces. The LED on
the assigned button indicates whether the partition
should be considered open (LED is lit; control units
work together as one) or closed (LED is off; control
units work independently in separate spaces). A
contact closure will open the partition; a contact
opening will close the partition. Wallstations
programmed for partitioning are only used for
partitioning, and each button is configured to control
different combinations of control units. When the
partition between two GRAFIK Eye QS control units is
open, the control units act together.

22BB PPaarrttiittiioonn::

2-button wallstations only. The top
button indicates partition open, and the bottom
button indicates partition closed.

22BB FFiinnee TTuunnee::

2-button wallstations only. The buttons
function as raise and lower buttons for the assigned
zones. Zones are assigned by pressing the raise and
lower buttons simultaneously; repeat to change
assignments.

22BB SSeeqquueennccee::

2-button wallstations only. This
function scrolls through scenes 5 through 16 using
their assigned fade rates, then repeats. For
showroom-type applications. Program as you would
for the Scene function.

22BB PPaanniicc::

2-button wallstations only. Pressing the
button sends all assigned zones immediately to
scene 16, and locks out all button presses on all
connected wallstations and control units. Program as
you would for the Scene function.

TTooggggllee::

1-button wallstations only. The button toggles

between scene 1 and off.

WWiinnddooww ttrreeaattmmeennttss::

Assign control of a group of

shades to a wallstation.

NNoottee::

If a control unit has devices connected to it
through contact closure inputs, CCI1 follows
the top button and CCI2 follows the bottom
button. The contact closure is equivalent to a
button press.
Exception: On a 2-button wallstation, CCI1
closure action follows the top button and
opening action follows the bottom button.

11Occupant Copy Installation Instructions

## BBuuttttoonnss

KKeeyyppaadd FFuunnccttiioonn 11 22 33 55 77

Zone XXXXX

Partition X X X

2B Partition X

Clear X

Zone Lockout X

Fine Tune X

Sequence X

Panic X

Window Treatments X X X

Scene Options 1, Off 1, Off 1-3 1-4, Off 1-7

(toggle) 5, Off 5-7 5-8, Off 9-15

9, Off 9-11 9-12, Off 1-6, Off

12, Off 13-15 13-16, Off 9-19, Off

1, 2 1-2, Off 1-5

5, 6 5-6, Off 5-9

9, 10 9-10, Off 9-13

13, 14 13-14, Off 13-16

NNootteess
See the previous page for full explanations of the standard functions.
Wallstations with dual keypads: Each keypad functions independently and is programmed separately.
Wallstations with Raise/Lower buttons: These buttons function only when the wallstation function is either zone

control or control of scenes.

SeeTouch® QS Wallstation Button Functions Summary

Program as two
3-button keypads

Program as one 3­button keypad and
one 2-button keypad

Program as two
2-button keypads

12Installation Instructions Occupant Copy

Adjusting Window Treatment
Settings

Setting Limits

Note: Entering Limit Setup mode may cause window

treatments to move approximately 8 inches up
or down. Be sure that each window treatment
is positioned so that the fabric can safely
move 8 inches up or down before entering
Limit Setup mode.
To be able to adjust window treatment limits,
your wallstation must have raise and lower
buttons. If your model does not have these,
please contact Lutron Technical Support or
refer to your window treatment documentation
to use the buttons on your EDU to manually
set limits.

1. On your shade keypad, press and
hold the top and raise buttons
simultaneously for 3 seconds. The
LEDs next to the top and bottom
buttons will cycle.

Note: At any time while in Limit Setup mode, you

can move all window treatments together to
their current open limit by slowly double­pressing the top button, or to their current
close limit by slowly double-tapping the
bottom button.

Note: Once EDUs (electronic drive units of the

window treatment) have been assigned to
shade keypads, limits can be set for an EDU
only using the shade keypad it is assigned to,
and a shade keypad can set limits only for
those EDUs assigned to it.

2. Select the EDU you want to to adjust using the top
button on the shade keypad. Each time you press
the top button, a different EDU that is assigned to
that shade keypad will open and close in an 8­inch range to indicate it is selected. Press the top
button until the EDU for the window treatment you
wish to adjust moves. (You can also use the
bottom button, which moves through the assigned
EDUs in the opposite order.)

3. Adjust the currently selected EDU
to the desired level for the open
limit (the maximum the window
treatment is allowed to open)
using the raise and lower buttons.

4. Press and hold the top button on the shade
keypad simultaneously for 3 seconds to store the
current position as the open limit. The LED next to
the top button will flash quickly for 2 seconds.

5. Adjust the currently selected EDU to the desired
level for the close limit (the maximum the window
treatment is allowed to close) using the raise and
lower buttons.

6. Press and hold the bottom button on the shade
keypad for 3 seconds to store the current position
as the close limit. The LED next to the bottom
button will flash quickly for 2 seconds.

7. Repeat steps 2 through 6 to set the open and
close limits for each window treatment assigned to
the shade keypad.

8. Press and hold the top and raise buttons on the
shade keypad simultaneously for 3 seconds to exit
Limit Setup mode.

13Occupant Copy Installation Instructions

Preset Adjustment: Simple Method

Note: The top button will always open the shades

fully, and the bottom button will always close
the shades fully. Only the shade presets
activated by the intermediate buttons can be
reprogrammed.

1. Use the raise and lower buttons on
the shade keypad to set all EDUs
(electronic drive units of the
window treatments) to the desired
preset levels.

2. Press and hold the respective preset
button on the shade keypad for 3
seconds to save the EDU preset
positions. The LED next to the
button will flash and then light
continuously, indicating the preset
has been stored.

Note: Once EDU presets have been assigned to

buttons on a shade keypad, those presets are
accessible for an EDU only using the shade
keypad it is assigned to, and a shade keypad
can access preset levels only for those EDUs
assigned to it.

Preset Adjustment: Advanced Method

Note: The advanced method for adjusting presets is

needed only if you wish to have the window
treatments assigned to the shade keypad set
at different positions in the preset. If, however,
you wish all the window treatments in the
group to be lined up with one another in the
preset, you should use the Simple Method
above.

Note: Entering Assignment mode will cause the

window treatments to move between their
open and close limits. Be sure that the open
and close limits have been set correctly.

1. On the shade keypad whose preset
you wish to adjust, press and hold the
top and bottom buttons simultaneously
for 3 seconds. The LEDs next to the
buttons will flash. EDUs (electronic
drive units) for the assigned window
treatments will move to their closed
limits, and EDUs for unassigned
window treatments will move to their
open limits.

2. Press the preset button you wish to adjust on that
shade keypad. The adjacent LED will blink rapidly.
EDUs for assigned window treatments will
automatically move to their current preset settings.

3. Use the raise and lower buttons
to move all EDUs for assigned
window treatments together to the
desired preset setting.

4. To move an EDU individually to its desired preset
setting, select the EDU using the top button on
the shade keypad. Each time you press the top
button, a different EDU that is assigned to that
shade keypad will open and close in an 8-inch
range. Press repeatedly until the EDU for the
window treatment you wish to adjust moves.
Adjust that EDU to the desired height using the
raise and lower buttons.
Repeat this step for all assigned EDUs you wish to
adjust.

5. Once you are satisfied that all the assigned EDUs
are set to the positions you want to assign as the
preset, press and hold the respective preset
button on the shade keypad for 3 seconds. The
preset will be saved.

6. Press and hold the top and bottom buttons on the
shade keypad simultaneously for 3 seconds to exit
to normal mode. The LEDs next to the buttons will
stop flashing.

Installation Instructions Occupant Copy14

Symptom Possible Causes

Troubleshooting

No communication with

GRAFIK

Eye

control unit.

Wallstation buttons do not work;
LEDs do not track.

LEDs do not light.

Contact closure inputs or sensor
input do not produce the desired
result in the system.

• Miswire or loose connection at the control link data lines 3 and 4.

• Wallstation has not been programmed or has been programmed incorrectly.

• Wallstation is miswired.

• Wallstation is not powered.

• Wallstation is not wired to the correct set of lights.

• Wallstation is not programmed to the correct device.

• Miswire or loose connection at wallstation(s) or processor on the control link
common and power connections 1 and 2.

• Wallstation has been programmed incorrectly.

• Miswire or loose connection at wallstation sensor/CCI connector.

• Wallstation has not been programmed or has been programmed incorrectly.

Wallstation buttons do not function
as intended.

• Wallstation has not been programmed or has been programmed incorrectly.

Occupant Copy Installation Instructions15

Troubleshooting: Window Treatment Functions

Symptom

EDU (electronic drive unit of the
window treatment) will not move

EDU (electronic drive unit of the window
treatment) does not fully open or fully
close

Window treatment moves in the
opposite direction when raise/lower
buttons are pushed

Keypad LEDs are off and keypad will
not control any window treatment

Keypad LEDs are on but keypad will not
control any window treatment

Keypad does not operate all the
window treatments it is assigned to

Window treatments in a room move on
their own

Possible Causes

EDU is not powered
Window treatment fabric is caught on
something
EDU is not assigned to a keypad

Presets have been set incorrectly
Limits have been set incorrectly
Window treatment fabric is caught on
something

Open and close limits have been
reversed

No power is going to keypad

All presets are set to the same height
Communications link is not wired to the
EDU
EDU has been unassigned from keypad
Open and close limits are the same

EDU has been unassigned from keypad
All presets are set to the same height
EDU is not wired correctly
Keypad is not wired correctly

EDUs are assigned to a keypad in
another room

Remedy

Check EDU power
Check and unbind window treatment
fabric
Assign the EDU to a keypad

Try using raise/lower buttons on keypad
Set limits correctly
Check and unbind window treatment
fabric

Set limits correctly

Check and wire power to keypad

Try using raise/lower buttons on keypad
Check and wire the EDU link

Reassign the EDU to the keypad
Set limits correctly

Reassign the EDU to the keypad
Try using raise/lower buttons on keypad
Check and rewire EDU
Check and rewire keypad

Reassign the EDU to the correct keypad

R

Lutron Electronics Co., Inc.
Made and printed in U.S.A.
P/N 030-939 Rev. A 10/07

Contact InformationWarranty

LLuuttrroonn EElleeccttrroonniiccss CCoo..,, IInncc..
OOnnee YYeeaarr LLiimmiitteedd WWaarrrraannttyy

For a period of one year from the date of purchase,and subject to
the exclusions and restrictions described below, Lutron warrants each
new unit to be free from manufacturing defects. Lutron will, at its option,
either repair the defective unit or issue a credit equal to the purchase
price of the defective unit to the Customer against the purchase price of
comparable replacement part purchased from Lutron. Replacements
for the unit provided by Lutron or,at its sole discretion, an approved
vendor may be new, used,repaired, reconditioned, and/or made by a
different manufacturer.

If the unit is commissioned by Lutron or a Lutron approved third party
as part of a Lutron commissioned lighting control system, the term of
this warranty will be extended, and any credits against the cost of
replacement parts will be prorated, in accordance with the warranty
issued with the commissioned system, except that the term of the unit's
warranty term will be measured from the date of its commissioning.
EEXXCCLLUUSSIIOONNSS AANNDD RREESSTTRRIICCTTIIOONNSS
This Warranty does not cover, and Lutron and its suppliers are not
responsible for:

1. Damage,malfunction or inoperability diagnosed by Lutron or a Lutron

approved third party as caused by normal wear and tear,abuse,
misuse, incorrect installation,neglect, accident, interference or
environmental factors, such as (a) use of incorrect line voltages, fuses
or circuit breakers; (b) failure to install, maintain and operate the unit
pursuant to the operating instructions provided by Lutron and the
applicable provisions of the National Electrical Code and of the Safety
Standards of Underwriter's Laboratories; (c) use of incompatible
devices or accessories; (d) improper or insufficient ventilation; (e)
unauthorized repairs or adjustments; (f) vandalism; or (g) an act of
God, such as fire,lightning, flooding, tornado,earthquake, hurricane or
other problems beyond Lutron's control.

2. On-site labor costs to diagnose issues with, and to remove, repair,

replace, adjust,reinstall and/or reprogram the unit or any of its
components.

3.Equipment and parts external to the unit, including those sold or

supplied by Lutron (which may be covered by a separate warranty).

4. The cost of repairing or replacing other property that is damaged

when the unit does not work properly,even if the damage was
caused by the unit.

EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, THERE
ARE NO EXPRESS OR IMPLIED WARRANTIES OF ANY TYPE,
INCLUDING ANY IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE OR MERCHANTABILITY. LUTRON DOES
NOT WARRANT THAT THE UNIT WILL OPERATE WITHOUT
INTERRUPTION OR BE ERROR FREE.

NO LUTRON AGENT, EMPLOYEE OR REPRESENTATIVE HAS ANY
AUTHORITY TO BIND LUTRON TO ANY AFFIRMATION,
REPRESENTATION OR WARRANTY CONCERNING THE UNIT.
UNLESS AN AFFIRMATION,REPRESENTATION OR WARRANTY MADE
BY AN AGENT, EMPLOYEE OR REPRESENTATIVE IS SPECIFICALLY
INCLUDED HEREIN, OR IN STANDARD PRINTED MATERIALS
PROVIDED BY LUTRON, IT DOES NOT FORM A PART OF THE BASIS
OF ANY BARGAIN BETWEEN LUTRON AND CUSTOMER AND WILL
NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER.

IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE
FOR EXEMPLARY, CONSEQUENTIAL, INCIDENTAL OR SPECIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS
OF PROFITS, CONFIDENTIAL OR OTHER INFORMATION, OR
PRIVACY;BUSINESS INTERRUPTION; PERSONAL INJURY; FAILURE

TO MEET ANY DUTY, INCLUDING OF GOOD FAITH OR OF
REASONABLE CARE; NEGLIGENCE, OR ANY OTHER PECUNIARY OR
OTHER LOSS WHATSOEVER),NOR FOR ANY REPAIR WORK
UNDERTAKEN WITHOUT LUTRON'S WRITTEN CONSENT ARISING
OUT OF OR IN ANY WAY RELATED TO THE INSTALLATION,
DEINSTALLATION, USE OF OR INABILITY TO USE THE UNIT OR
OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF
THIS WARRANTY, OR ANY AGREEMENT INCORPORATING THIS
WARRANTY, EVEN IN THE EVENT OF THE FAULT,TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY, BREACH OF CONTRACT OR
BREACH OF WARRANTY OF LUTRON OR ANY SUPPLIER,AND EVEN
IF LUTRON OR ANY OTHER PARTY WAS ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.

NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER MIGHT
INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, ALL DIRECT DAMAGES AND ALL DAMAGES LISTED
ABOVE), THE ENTIRE LIABILITY OF LUTRON AND OF ALL OTHER
PARTIES UNDER THIS WARRANTY ON ANY CLAIM FOR DAMAGES
ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE,
SALE, INSTALLATION, DELIVERY, USE, REPAIR,OR REPLACEMENT
OF THE UNIT,OR ANY AGREEMENT INCORPORATING THIS
WARRANTY, AND CUSTOMER'S SOLE REMEDY FOR THE
FOREGOING,WILL BE LIMITED TO THE AMOUNT PAID TO LUTRON
BY CUSTOMER FOR THE UNIT. THE FOREGOING LIMITATIONS,
EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE MAXIMUM
EXTENT ALLOWED BY APPLICABLE LAW, EVEN IF ANY REMEDY
FAILS ITS ESSENTIAL PURPOSE.
TTOO MMAAKKEE AA WWAARRRRAANNTTYY CCLLAAIIMM

To make a warranty claim,promptly notify Lutron within the warranty
period described above by calling the Lutron Technical Support Center
at [phone]. Lutron, in its sole discretion,will deter mine what
action, if any,is required under this warranty. To better enable Lutron to
address a warranty claim, have the unit's serial and model numbers
available when making the call. If Lutron, in its sole discretion,
determines that an on-site visit or other remedial action is necessary,
Lutron may send a Lutron Services Co. representative or coordinate the
dispatch of a representative from a Lutron approved vendor to
Customer's site, and/or coordinate a warranty service call between
Customer and a Lutron approved vendor.

This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.

These products may be covered under one or more of the following
U.S. patents: D461,782; and corresponding foreign patents.Other U.S.
and foreign patents may be pending.

National Electric Code, NEC, and NFPA are registered trademarks of
the National Fire Protection Association, Inc., Quincy, Massachusetts.

Lutron, the sunburst logo,Sivoia, seeTouch, and GRAFIK Eye are
registered trademarks of Lutron Electronics Co., Inc.
© 2007 Lutron Electronics Co., Inc.

Internet: www.lutron.com
E-mail: [e-mail]

WORLD HEADQUARTERS
USA

Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA

18036-1299
TEL [phone]
FAX [phone]
Toll-Free 1.888.LUTRON1
Technical Support 1.800.523.9466

North and South America

Technical Hotlines

USA, Canada, Caribbean: 1.800.523.9466
Mexico: +1.888.235.2910
Central/South America: +1.610.282.6701

EUROPEAN HEADQUARTERS
United Kingdom

Lutron EA Ltd.
6 Sovereign Close, London,

E1W 3JF United Kingdom
TEL [phone]
FAX [phone]
FREEPHONE (UK) 0800.282.107
Technical support +44.(0)20.7680.4481

ASIAN HEADQUARTERS
Singapore

Lutron GL Ltd.
15 Hoe Chiang Road,

#07-03 Euro Asia Centre, Singapore 089316
TEL [phone]
FAX [phone]

Asia Technical Hotlines

Northern China: 10.800.712.1536
Southern China: 10.800.120.1536
Hong Kong: 800.901.849
Indonesia: 001.803.011.3994
Japan: +81.3.5575.8411
Macau: 0800.401
Singapore: 800.120.4491
Taiwan: 00.801.137.737
Thailand: 001.800.120.665853
Other countries: +65.6220.4666