Lutron QSE-IO User Manual

QSE-IO Control Interface Programming Guide

Contents

Overview ........................................... 2

QSE-IO Operating Modes and DIP Switch Settings Overview . . . . 3

Equipment / Functionality Table ........................... 5

Scene Selection Operating Mode ......................... 6

Special Operating Mode: Sequencing...................... 7

Special Operating Mode: Zone Lockout .................... 8

Special Operating Mode: Scene Lockout ................... 9

Special Operating Mode: Panic...........................10

Special Operating Mode: Timeclock .......................11

Special Operating Mode: Afterhours .......................12

Shade Mode: Shade Input Preset .........................13

Shade Mode: Shade Input Raise, Lower, Stop ...............15

Shade Mode: Shade Input Dual Group .....................16

Shade Mode: Shade Input Dual Group Raise/Lower ...........17

Shade Mode: Shade Input Toggle.........................18

Shade Mode: AC Shade Output ..........................19

Partitioning Mode .....................................20

Occupancy Sensor Mode...............................21

Zone Toggle Mode ................................... 22

Zone Control Mode....................................23

Hotel Mode..........................................28

Integration Mode..................................... 30

page 1

integration conguration

shade stuffs

partitioning occ sensor

345678

Overview

QSE-IO Control Interface Programming Guide

These instructions detail the available functions and the accompanying necessary settings for programming a QSE-IO control interface in a Lutron system. For wiring, installation, system setup, additional operation instructions, and other non-programming information, please refer to the documentation that accompanied this and other devices in your system.

Programming Your System

The programming instructions in this guide are for standalone (GRAFIK Eye QS or QS link only) systems. For Energi Savr Node or Quantum systems, refer to the documentation that came with those products for programming instructions.

Switches and Connections

The DIP switches are numbered from 1 through 8. For operating mode conﬁguration, only switches 3 through 8 are used (with certain noted exceptions; see the speciﬁc conﬁguration instructions).

Unit Overview

QS Link

4 3 21

1234567

Contact Closure Outputs

CCO 1 NC

CCO 1 NO

1-2 COM

CCO 2 NC

CCO 2 NO

CCO 3 NC

CCO 3 NO

Program button

3-4 COM

CCO 4 NC

CCO 4 NO

CCO 5 NC

DIP switches

O

1 2 3 4 5 6 7 8

N

Legend:

Up/On

Down/Off

Closure Inputs

CCO 5 NO

5 COM

CCI 1

Contact

CCI 2

CCI 3

CCI 4

CCI 5

COM

The CCI and CCO wiring terminals each accept one 28 to 16 AWG (0.08 to 1.5 mm2) wire. Refer to the speciﬁc conﬁguration instructions for details on wiring for your desired operating mode.

Operating Modes

Each QSE-IO can be assigned only one (1) operating mode from those detailed on the following pages. By choosing the correct input (CCI) terminal and accompanying DIP switch settings, you can select the speciﬁc action each operating mode will perform.

page 2

QSE-IO Control Interface Programming Guide

integration conguration

shade stuffs

partitioning occ sensor

345678

QSE-IO Operating Modes and DIP Switch Settings Overview

Mode Dip Switch Contact Closures Invoke:

Configuration 3 4 5 6 7 8 Input 1 Input 2 Input 3 Input 4 Input 5 Inputs Outputs

Scene 1 Scene 2 Scene 3 Scene 4 Scene Off

Scene 5 Scene 6 Scene 7 Scene 8 Scene Off

Scene 9 Scene 10 Scene 11 Scene 12 Scene Off

Scene 13 Scene 14 Scene 15 Scene 16 Scene Off

• For AC shades with only 2 inputs (open/close), set DIP switch 1 to the up/on position to enable the feature

• The QSE-IO provides no power, only a control signal, to AC shades. Refer to the instructions that came with your shades

Scene selection

Shade input preset

(“stop if moving”)

Shade input preset

(no “stop if moving”)

(raise, lower, stop)

Shade input dual group

(“stop if moving”)

Shade input dual group

(no “stop if moving”)

Shade input dual group

Shade input toggle

(“stop if moving”:

open/stop/close/stop)

Shade input toggle

(no “stop if moving”:

AC Shade output

(maintained outputs)

AC Shade output

(momentary stop)

AC Shade output

(momentary outputs)

Notes

that mimics “stop” (asserts both “open” and “close” CCOs together when a “stop” command is received).

for more information.

Special

(maintained)

Special

(momentary)

Special 2

(maintained)

Special 2

(momentary)

Shade input

(raise/lower)

open/close)

Scene 1 Scene 2 Scene 3 Scene 4 Scene Off

Scene 5 Scene 6 Scene 7 Scene 8 Scene Off

Scene 9 Scene 10 Scene 11 Scene 12 Scene Off

Scene 13 Scene 14 Scene 15 Scene 16 Scene Off

Sequence 5–16

Sequence 1–4

Shade open

Open Group 1

Raise/Stop Group 1

Toggle Group 1

Open Group 1

Zone lockout

Shade preset 1

Shade raise

Close Group 1

Lower/Stop Group 1

Toggle Group 2

Stop Group 1Close

Stop Group 1 if moving

Scene lockout

Shade preset 2

Shade lower

Open Group 2

Raise/Stop Group 2

Toggle Group 3

Group 1

Close Group 1

Panic mode

Shade preset 3

Shade stop

Close Group 2

Lower/Stop Group 2

Toggle Group 4

Open Group 2

Timeclock Maintained

Timeclock Momentary

Afterhours mode

Shade close

—

— Momentary Momentary

Toggle Group 5

Close Group 2

Maintained or Momentary

Maintained

Momentary

Maintained or Momentary

Momentary or Maintained

Maintained or Momentary

Momentary Momentary

Maintained Momentary

Maintained or Momentary

Maintained

Momentary

Maintained

Maintained (except 2, which is Momentary)

Momentary

Legend:

Up/On

Down/Off

page 3

integration conguration

shade stuffs

partitioning occ sensor

345678

QSE-IO Control Interface Programming Guide

QSE-IO Operating Modes and DIP Switch Settings Overview (continued)

Mode Dip Switch Contact Closures Invoke:

Configuration 3 4 5 6 7 8 Input 1 Input 2 Input 3 Input 4 Input 5 Inputs Outputs

Partitioning

(momentary)

Partitioning

(maintained)

Occupancy sensor

(auto on/off)

Occupancy sensor

(manual on/auto off)

Zone toggle with raise/lower

(maintained output)

(momentary output)

Zone toggle

(maintained)

Zone toggle

(momentary)

(maintained)

(momentary)

Zone control

Wall 1 Wall 2 Wall 3 Wall 4 Wall 5 Momentary Maintained

Wall 1 Wall 2 Wall 3 Wall 4 Wall 5 Maintained Maintained

Generates events on occupancy and vacancy Maintained Maintained

Generates events on vacancy only Maintained Maintained

Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Maintained

Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Momentary

Toggle 1 Toggle 2 Toggle 3 Raise Lower Maintained

Toggle 1 Toggle 2 Toggle 3 Raise Lower Momentary

Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Maintained

Toggle 1 Toggle 2 Toggle 3 Toggle 4 Toggle 5 Momentary

Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Maintained

Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Momentary

Maintained

Momentary

Zone control

(pulsed output)

Hotel configuration 1

Hotel configuration 2

Integration configuration

Notes

• Occupancy sensor: Each input represents 1 sensor/group of sensors. Response to sensor event is programmable at the assigned lighting control.

• “Momentary” output pulse is of fixed duration (250 ms default). “Pulsed” output duration corresponds to activating button being held/released.

• Hotel: “Service” and “Privacy” are mutually exclusive; “Doorbell” is locked out when “Privacy” is active.

• DIP switch 1 must be up/on to activate the "Start/End Afterhours" feature on CCI4.

• DIP switch 2 must be up/on to activate the "Toggle Scene" or "Scene Blackout" feature on CCI 5.

• Occupancy sensors will not participate in partitioning logic.

Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Maintained

Pulse 1 Pulse 2 Pulse 3 Pulse 4 Pulse 5 Momentary

Service (make up room)

Control output 1

Privacy (do not disturb)

Control output 2

Doorbell

Control output 3

Start/end afterhours mode

Control output 4

Toggle Scene 1/ Off

Enable/ disable Scene lockout

Control output 5

1-3: Maintained or Momentary 4-5: Maintained

Maintained or Momentary

Pulsed

Maintained (except 3)

Maintained or Momentary

Legend:

Up/On

Down/Off

page 4

QSE-IO Control Interface Programming Guide

Equipment / Functionality Table

Look below for the Equipment / Functionality you have/want,

Look to the right for the Operating Mode you need to refer to for the correct DIP switch setting and programming instructions

Table applies only to standalone systems See next page for notes

Contact Closure Inputs

Contact Closure Outputs

Control Sivoia QS Shades via CCIs

Control AC Shades from QS Shade Controllers (wallstations) via CCOs

Control / M onitor GRAFIK Eye QS and / or Energi Savr Node QS

Implement Partition Logic for 5 Partition Walls via CCIs

Receive Signals from up to 5 Groups of Occupancy Sensors

Integrate a QS System into a Hotel Room √ Control RS232 or Ethernet and/or

Monitor CC Is / CCOs Control CCOs from QS Input Devices

(e.g., wallstations)

Notes

• Table applies only to standalone systems (GRAFIK Eye QS or Energi Savr Node systems). For Quantum systems, refer to the instructions that accompanied that equipment.

• A Momentary output pulse is of fixed duration (250 ms default).

• A Pulsed output pulse's duration corresponds to the activating button being held/released.

• Possible QS input devices include seeTouch QS wallstations, Pico wireless controls (via a QSM), QS keyswitch, QS IR Eye remote, another QSE-IO control interface, or shade keypads on a GRAFIK Eye QS control unit.

then

Special

Scene Selection

Maintained √ √ √ √ √ √ √ √ √ √ √ √ √ Momentary √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ Maintained √ √ √ √ √ √ √ √ √ √ √ √ Momentary √ √ √ √ √ √ √ Pulsed √ √ √ Open / Close √ √ √ √ √ 3 Presets √ Raise/Lower √ √ Stop if Moving √ √ √ 1 Shade Group √ √ 2 Shade Groups √ √ 5 Shade Groups √ √

Scene Control via CCIs √ √ Scene Monitor via CCOs √ Zone Toggle via CCIs √ √ √ √ Zone Monitor via CCOs √ Sequencing √ Scene Lockout √ √ Zone Lockout √ Panic √ Afterhours Start/Stop √ √ Timeclock Disable

(GRAFIK Eye QS only)

√

Shade Input

Raise, Lower, Stop

Shade Input Preset

Raise/Lower

Shade Input Dual Group

Shade Input Toggle

Shade Input Dual Group

Open/Close

Shade Output

Shade Input Toggle

Open/Close (stop if moving)

√ √ √

√ √ √ √ √ √ √

Momentary Stop

Maintained Outputs

Partitioning

Zone Toggle

Zone Control

Shade Output

Occupancy Sensor

Momentary Outputs

√

Zone Control

Maintained Outputs

Momentary Outputs

Hotel

Zone Control

Pulsed Outputs

√

Integration

page 5

QSE-IO Control Interface Programming Guide

scene selection

special and special 2

shade stuffs

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Scene Selection Operating Mode

• Links to one or more GRAFIK Eye QS control

units and/or Energi Savr Node areas.

• CCIs select between 4 scenes and Off.

• CCOs track currently active scene.

• Inputs: either momentary or maintained.

• Outputs: all maintained or all momentary

(see chart).

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings Related Action

345678

Input 1: Scene 1 Input 2: Scene 2 Input 3: Scene 3 Input 4: Scene 4 Input 5: Off Outputs: Maintained

Input 1: Scene 5 Input 2: Scene 6 Input 3: Scene 7 Input 4: Scene 8 Input 5: Off Outputs: Maintained

Input 1: Scene 9 Input 2: Scene 10 Input 3: Scene 11 Input 4: Scene 12 Input 5: Off Outputs: Maintained

Input 1: Scene 13 Input 2: Scene 14 Input 3: Scene 15 Input 4: Scene 16 Input 5: Off Outputs: Maintained

Input 1: Scene 1 Input 2: Scene 2 Input 3: Scene 3 Input 4: Scene 4 Input 5: Off Outputs: Momentary

page 6

345678

Legend:

Up/On

Down/Off

Input 1: Scene 5 Input 2: Scene 6 Input 3: Scene 7 Input 4: Scene 8 Input 5: Off Outputs: Momentary

Input 1: Scene 9 Input 2: Scene 10 Input 3: Scene 11 Input 4: Scene 12 Input 5: Off Outputs: Momentary

Input 1: Scene 13 Input 2: Scene 14 Input 3: Scene 15 Input 4: Scene 16 Input 5: Off Outputs: Momentary

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Sequencing

• Links to one or more GRAFIK Eye QS control

units and / or Energi Savr Node areas.

• Moves sequentially through a group of scenes

(see chart) using Input 1.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure enables sequencing; opening disables sequencing.

- Momentary: button press toggles between enable and disable sequencing.

• Outputs: maintained.

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Maintained Inputs: Input 1: closure enables, opening

disables sequencing Scenes 5-16

Output: Maintained

Momentary Inputs: Input 1: button press toggles

enable/disable sequencing Scenes 5-16

Output: Maintained

Maintained Inputs: Input 1: closure enables, opening

disables sequencing Scenes 1-4

Output: Maintained

Momentary Inputs: Input 1: button press toggles

enable/disable sequencing Scenes 1-4

Output: Maintained

page 7

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Zone Lockout

• Links to one or more GRAFIK Eye QS control

units and / or Energi Savr Node areas.

• Prevents modiﬁcations to programmed preset

light levels using Input 2.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure enables lockout; opening disables lockout.

- Momentary: button presses toggle between enable and disable lockout.

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings

345678

Legend:

Up/On

Down/Off

Related Action

Maintained Inputs: Input 2: closure enables,

opening disables zone lockout

Output: Maintained

Momentary Inputs: Input 2: button press toggles

enable/disable zone lockout

Output: Maintained

Maintained Inputs: Input 1: closure enables,

opening disables zone lockout

Output: Maintained

Momentary Inputs: Input 1: button press toggles

enable/disable zone lockout

Output: Maintained

page 8

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Scene Lockout

• Links to one or more GRAFIK Eye QS control units

and / or Energi Savr Node areas.

• Prevents selected scene or programmed preset

levels from changing using Input 3.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure enables lockout; opening disables lockout.

- Momentary: button presses toggle between enable and disable lockout.

• Outputs: maintained.

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings

345678

Legend:

Up/On

Down/Off

Related Action

Maintained Inputs: Input 3: closure enables,

opening disables scene lockout

Output: Maintained

Momentary Inputs: Input 3: button press toggles

enable/disable scene lockout

Output: Maintained

Maintained Inputs: Input 1: closure enables, opening

disables scene lockout

Output: Maintained

Momentary Inputs: Input 1: button press toggles

enable/disable scene lockout

Output: Maintained

page 9

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Panic

• Links to one or more GRAFIK Eye QS control

units and / or Energi Savr Node areas.

• Activates Scene 16 and enables scene lockout

using Input 4.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure enables panic; opening disables panic.

- Momentary: button presses toggle between enable and disable panic.

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings

345678

Legend:

Up/On

Down/Off

Related Action

Maintained Inputs: Input 4: closure enables,

opening disables panic

Output: Maintained

Momentary Inputs: Input 4: button press toggles

enable/disable panic

Output: Maintained

Maintained Inputs: Input 1: closure enables, opening

disables panic

Output: Maintained

Momentary Inputs: Input 1: button press toggles

enable/disable panic

Output: Maintained

page 10

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Timeclock

• Links to one or more GRAFIK Eye QS control

units.

• On GRAFIK Eye QS control units only, disables

internal timeclock using Input 5.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure disables timeclock; opening enables timeclock.

- Momentary: button presses toggle between disable and enable timeclock.

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS

control units.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Maintained inputs Input 5: contact closure

disables timeclock; contact opening enables timeclock

Output: Maintained

Momentary inputs Input 5: button press toggles

disable/enable timeclock

Output: Maintained

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Down/Off

page 11

QSE-IO Control Interface Programming Guide

special and special 2

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Special Operating Mode: Afterhours

• Links to one or more GRAFIK Eye QS control

units and / or Energi Savr Node areas.

• Enables afterhours mode using Input 5.

• Inputs: momentary only or maintained only

(see chart)

- Maintained: closure enables afterhours; opening disables afterhours.

- Momentary: button presses toggle between enable and disable afterhours.

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS

control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 through 5 will cycle.

2.To assign a GRAFIK Eye QS control unit to the

QSE-IO, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units.

3. Exit programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Maintained Inputs: Input 5: button press toggles

enable/disable afterhours

Output: Maintained

Momentary Inputs: Input 5: closure enables,

opening disables afterhours

Output: Maintained

page 12

QSE-IO Control Interface Programming Guide

shade stuffs

partitioning occ sensor

345678

shade stuffs

partitioning occ sensor

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Shade Mode: Shade Input Preset

• Links to one or more Sivoia QS shades.

• Sends shades to a speciﬁed preset level,

depending on input (see chart). Can be set to stop shades if moving.

• Inputs: momentary or maintained.

• Outputs: maintained only.

• Communicates directly with Sivoia QS shades.

Programming Instructions

Assign shades before programming:

1. Enter programming mode on the QSE-IO control

interface: Press and hold the Program button for 3 seconds. LEDs 1 and 5 will blink. Make sure DIP switch 1 is down (Off).

2. Shades that are currently assigned to the QSE-IO

will move to their close limit, and shades that are not assigned will move to their open limit.

3. To select a shade, tap the Program button. The

selected shade will wiggle up and down. To advance through all shades, tap the Program button. To go to the previous shade, double-tap the Program button.

4. When the desired shade is selected, press and

hold the Program button for 3 seconds to assign it (if unassigned) or unassign it (if assigned) to the QSE-IO. The 5 LEDs will blink for 2 seconds to indicate success once you release the button.

5. When all shades you wish to be assigned are at

their close limit, and all shades you wish to be unassigned are at their open limit, exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Program shades:

Three presets are available on QS shades. Shade default presets are:

- Preset 1: all assigned shades 75% open

- Preset 2: all assigned shades 50% open

- Preset 3: all assigned shades 25% open

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Stop if moving: Closure toggles action/stop Input 1: Open/Stop shade Input 2: Shade to preset 1/Stop Input 3: Shade to preset 2/Stop Input 4: Shade to preset 3/Stop Input 5: Close/Stop shade Outputs: Maintained

No stop if moving: Closure causes action Input 1: Open shade Input 2: Shade to preset 1 Input 3: Shade to preset 2 Input 4: Shade to preset 3 Input 5: Close shade Outputs: Maintained

To adjust these presets, follow these steps:

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LEDs 1 and 5 will blink. Make sure DIP switch 1 is up (On) and DIP switches 2 and 3 are down (Off).

2. Preset 1 will be selected. To advance through the presets, tap the Program button. To go to the previous preset, double-tap the Program button. LED 2, 3, or 4 will light to indicate which preset is selected (1, 2, or 3).

3. When the desired preset is selected, press and hold the Program button for 2 seconds. All assigned QS shades will go to their assigned value for the selected preset.

4. To select the shade you want to change, tap the Program button to advance through the assigned shades. The selected shade will wiggle up and down.

5. When the desired shade is wiggling, set DIP switch 2 up (On). The shade will stop wiggling.

6. To raise the selected QS shade to the desired position for this preset, set DIP switch 3 up (On) and use the Program button to adjust the QS shade. To lower the shade, set DIP switch 3 down (Off) and use the Program button to adjust.

(continued on next page)

page 13

QSE-IO Control Interface Programming Guide

Shade Mode: Shade Input Preset (continued)

7. To move to another shade, set DIP switch 2 down (Off). Repeat steps 4 through 6 until all shades are set as desired for this preset.

8. With DIP switch 2 down (Off), press and hold the Program button on the QSE-IO for 3 seconds to save this preset. Return to step 2 to adjust additional presets.

9. Exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Note: At any point while DIP switch 2 is down (Off), press and hold the Program button for 15 seconds to exit programming mode without saving any presets.

Setting Limits

The open and close limits must be set on shades to ensure they reach the desired levels when those buttons are pushed, and to ensure they do not go beyond those levels when being raised or lowered.

Remote limit setting is not supported by the QSE-IO control interface. To set limits before programming, see the programming guide that accompanied your shades. Or, if your system contains a GRAFIK Eye QS control unit or seeTouch QS wallstation, refer to the programming instructions for one of those devices.

page 14

QSE-IO Control Interface Programming Guide

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Shade Mode: Shade Input Raise, Lower, Stop

• Links to one or more Sivoia QS shades.

• Allows user to open, close, raise, and lower shades, depending on input (see chart).

• Inputs: momentary or maintained.

• Outputs: maintained.

• Communicates directly with Sivoia QS shades.

Programming Instructions

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Input 1: Open shade Input 2: Raise shade Input 3: Lower shade Input 4: Stop shade Input 5: Close shade Outputs: Maintained

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LEDs 1 and 5 will blink. Make sure DIP switch 1 is down (Off).

2. Shades that are currently assigned to the QSE-IO will move to their close limit, and shades that are not assigned will move to their open limit.

3. To select a shade, tap the Program button. The selected shade will wiggle up and down. To advance through all shades, tap the Program button. To go to the previous shade, double-tap the Program button.

4. When the desired shade is selected, press and hold the Program button for 3 seconds to assign it (if unassigned) or unassign it (if assigned) to the QSE-IO. The 5 LEDs will blink for 2 seconds to indicate success once you release the button.

5. When all shades you wish to be assigned are at their close limit, and all shades you wish to be unassigned are at their open limit, exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Setting Limits

The open and close limits must be set on shades to ensure they reach the desired levels when those buttons are pushed, and to ensure they do not go beyond those levels when being raised or lowered.

Remote limit setting is not supported by the QSE-IO control interface. To set limits before programming, see the programming guide that accompanied your shades. Or, if your system contains a GRAFIK Eye QS control unit or seeTouch QS wallstation, refer to the programming instructions for one of those devices.

page 15

QSE-IO Control Interface Programming Guide

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Shade Mode: Shade Input Dual Group

• Links to one or more Sivoia QS shades.

• Allows user to open or close shades, depending on input (see chart). Can be set to stop shades if moving.

• Inputs: maintained or momentary.

• Outputs: maintained only.

• Communicates directly with Sivoia QS shades.

Programming Instructions

Group Selection

1. Make sure DIP switch 1 is down (Off). Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 5 seconds. The LED(s) corresponding to associated shade groups will blink rapidly.

2. To advance through all shade groups, tap the Program button. To go to the previous shade group, double-tap the Program button.

3. When the desired shade group is selected, set DIP switch 1 up (On) to "lock in" the selected group. The LEDs corresponding to the selected group will blink slowly.

Shade Selection

4. Shades that are currently assigned to the selected group will move to their close limit, and shades that are not assigned will move to their open limit.

5. To advance through shades, tap the Program button. To go to the previous shade, double-tap the Program button. The selected shade will wiggle.

6. To assign the selected (wiggling) shade to a group, press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds), the shade will close, indicating assignment. To unassign an assigned shade, select it (wiggle), then press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds), the shade will open, indicating that it is no longer assigned. Repeat for all shades you wish to assign to this shade group.

7. Repeat steps 1 through 6 for all remaining shade groups and shades you wish to assign to those groups.

8. When all shades and shade groups are assigned, set DIP switch 1 down (Off) to "unlock" the selected group. The LEDs corresponding to the selected group will blink rapidly.

9. To exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Stop if moving: Closure toggles action/stop Input 1: Open/stop Group 1 shades Input 2: Close/stop Group 1 shades Input 3: Open/stop Group 2 shades Input 4: Close/stop Group 2 shades Input 5: No function Outputs: Maintained

No stop if moving: Closure causes action Input 1: Open Group 1 shades Input 2: Close Group 1 shades Input 3: Open Group 2 shades Input 4: Close Group 2 shades Input 5: No function Outputs: Maintained

Notes

• 2 groups are available for this mode: Group 1

(CCI 1 and CCI 2), and Group 2 (CCI 3 and CCI

4).

• Preset Adjust Mode is not supported in this shade

mode.

Setting Limits

The open and close limits must be set on shades to ensure they reach the desired levels when those buttons are pushed, and to ensure they do not go beyond those levels when being raised or lowered.

Remote limit setting is not supported by the QSE-IO control interface. To set limits before programming, see the programming guide that accompanied your shades. Or, if your system contains a GRAFIK Eye QS control unit or seeTouch QS wallstation, refer to the programming instructions for one of those devices.

page 16

QSE-IO Control Interface Programming Guide

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Shade Mode: Shade Input Dual Group Raise / Lower

• Links to one or more Sivoia QS shades.

• Toggles raise / stop or lower / stop for groups of shades, depending on input (see chart).

• Inputs: momentary only.

• Outputs: momentary only.

• Communicates directly with Sivoia QS shades.

Programming Instructions

Group Selection

1. Make sure DIP switch 1 is down (Off). Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 5 seconds. The LED(s) corresponding to associated shade groups will blink rapidly.

2. To advance through all shade groups, tap the Program button. To go to the previous shade group, double-tap the Program button.

3. When the desired shade group is selected, set DIP switch 1 up (On) to "lock in" the selected group. The LEDs corresponding to the selected group will blink slowly.

Shade Selection

4. Shades that are currently assigned to the selected group will move to their close limit, and shades that are not assigned will move to their open limit.

5. To advance through shades, tap the Program button. To go to the previous shade, double-tap the Program button. The selected shade will wiggle.

6. To assign the selected (wiggling) shade to a group, press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds) the shade will close, indicating assignment. To unassign an assigned shade, select it (wiggle), then press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds) the shade will open, indicating that it is no longer assigned. Repeat for all shades you wish to assign to this shade group.

7. Repeat steps 1 through 6 for all remaining shade groups and shades you wish to assign to those groups.

8. When all shades and shade groups are assigned, set DIP switch 1 down (Off) to "unlock" the selected group. The LEDs corresponding to the selected group will blink rapidly.

9.To exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Closure causes action; Opening stops action Input 1: Raise/Stop Group 1 shades Input 2: Lower/Stop Group 1 shades Input 3: Raise/Stop Group 2 shades Input 4: Lower/Stop Group 2 shades Input 5: No function Outputs: Momentary

Notes

• 2 groups are available for this mode: Group 1

(CCI1 and CCI 2), and Group 2 (CCI3 and CCI 4).

• Preset Adjust Mode is not supported in this shade

mode.

Setting Limits

The open and close limits must be set on shades to ensure they reach the desired levels when those buttons are pushed, and to ensure they do not go beyond those levels when being raised or lowered.

Remote limit setting is not supported by the QSE-IO control interface. To set limits before programming, see the programming guide that accompanied your shades. Or, if your system contains a GRAFIK Eye QS control unit or seeTouch QS wallstation, refer to the programming instructions for one of those devices.

page 17

QSE-IO Control Interface Programming Guide

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Shade Mode: Shade Input Toggle

• Links to one or more Sivoia QS shades.

• Inputs: momentary (stop if moving:

open / stop / close / stop) or maintained (no stop if moving: open / close).

• Outputs: momentary only (closure while assigned shade or shades are moving).

• Communicates directly with Sivoia QS shades.

Programming Instructions

Group Selection

1. Make sure DIP switch 1 is down (Off). Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 5 seconds. The LED(s) corresponding to associated shade groups will blink rapidly.

2. To advance through all shade groups, tap the Program button. To go to the previous shade group, double-tap the Program button.

3. When the desired shade group is selected, set DIP switch 1 up (On) to "lock in" the selected group. The LEDs corresponding to the selected group will blink slowly.

Shade Selection

4. Shades that are currently assigned to the selected group will move to their close limit, and shades that are not assigned will move to their open limit.

5. To advance through shades, tap the Program button. To go to the previous shade, double-tap the Program button. The selected shade will wiggle.

6. To assign the selected (wiggling) shade to a group, press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds) the shade will close, indicating assignment. To unassign an assigned shade, select it (wiggle), then press and hold the Program button for 5 seconds. When you release the Program button (after 5 seconds) the shade will open, indicating that it is no longer assigned. Repeat for all shades you wish to assign to this shade group.

7. Repeat steps 1 through 6 for all remaining shade groups and shades you wish to assign to those groups.

8. When all shades and shade groups are assigned, set DIP switch 1 down (Off) to "unlock" the selected group. The LEDs corresponding to the selected group will blink rapidly.

9.To exit programming mode on the QSE-IO control interface: Press and hold the Program button for 15 seconds.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Momentary inputs: Stop if moving: Closure toggles open/stop/close/stop Input 1: Toggle Group 1 shades Input 2: Toggle Group 2 shades Input 3: Toggle Group 3 shades Input 4: Toggle Group 4 shades Input 5: Toggle Group 5 shades Outputs: Momentary

Maintained inputs: No stop if moving: Opening closes shades Closure opens shades Input 1: Toggle Group 1 shades Input 2: Toggle Group 2 shades Input 3: Toggle Group 3 shades Input 4: Toggle Group 4 shades Input 5: Toggle Group 5 shades Outputs: Momentary

Notes

• 5 groups are available for this mode: Groups 1

through 5, corresponding to CCI1 through CCI 5.

• Preset Adjust Mode is not supported in this shade

mode.

Setting Limits

The open and close limits must be set on shades to ensure they reach the desired levels when those buttons are pushed, and to ensure they do not go beyond those levels when being raised or lowered.

Remote limit setting is not supported by the QSE-IO control interface. To set limits before programming, see the programming guide that accompanied your shades. Or, if your system contains a GRAFIK Eye QS control unit or seeTouch QS wallstation, refer to the programming instructions for one of those devices.

page 18

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

QSE-IO Control Interface Programming Guide

Shade Mode: AC Shade Output

• Links to one or more of the following through the CCO connection on the QSE-IO interface:

- third-party AC shade or projection screen

groups

• Allows control of CCOs from QS devices, such as:

- GRAFIK Eye QS shade column

- seeTouch QS shade wallstation

- Pico wireless control (through QSM)

- QS keyswitch

- QS IR Eye remote

- another QSE-IO control device

- QSE-CI-NWK-E Ethernet and RS232 interface See charts for speciﬁcs on DIP switch settings and inputs / outputs that correspond to the signals required by various AC shades.

• Inputs: maintained or momentary.

• Outputs: see charts.

• Communicates directly with devices listed above. Special note: For AC shade controllers with only

2 inputs (open / close), set DIP switch 1 to the up / on position to enable the feature that mimics "stop" (asserts both "open" and "close" CCOs together when a "stop" command is received).

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Input 1: Open Group 1 shades Input 2: Stop Group 1 shades Input 3: Close Group 1 shades Input 4: Open Group 2 shades Input 5: Close Group 2 shades Outputs: Maintained

(Output 2 is Momentary)

Input 1: Open Group 1 shades Input 2: Stop Group 1 shades Input 3: Close Group 1 shades Input 4: Open Group 2 shades Input 5: Close Group 2 shades Outputs: Momentary

Programming Instructions

1. Enter programming mode: Press and hold the open and close buttons on a GRAFIK Eye QS shade column or seeTouch QS shade wallstation for 3 seconds. The LEDs on the QSE-IO control device will turn off. Note: For other supported device types, refer to the instructions that accompanied each one.

2. On the QSE-IO you wish to obey commands from that shade column or wallstation, tap the Program button on the QSE-IO once to assign shade Group 1 (LEDs 1 through 3 will blink), or twice to assign shade Group 2 (LEDs 4 and 5 will blink).

3. To unassign shade Group 1, tap the Program button once when LEDs 1 through 3 are blinking; the LEDs will stop blinking. To unassign shade Group 2, double-tap the Program button once when LEDs 4 and 5 are blinking; the LEDs will stop blinking.

4. Exit programming mode: Press and hold the open and close buttons on the shade column or wallstation for 3 seconds.

Note: The QSE-IO provides no power, only a control signal, to AC shades. Refer to the instructions that came with your shades for more information.

page 19

QSE-IO Control Interface Programming Guide

partitioning occ sensor

integration conguration

shade stuffs

partitioning occ sensor

345678

Partitioning Mode

• Links to one or more GRAFIK Eye QS control units and / or Energi Savr Node areas per I/O input.

• Allows multiple GRAFIK Eye QS control units and / or Energi Savr Node areas to operate either independently (when the partition is closed) or in parallel (when the partition is open).

• Inputs: momentary only or maintained only (see chart)

- Maintained: closure opens partition;

opening closes partition.

- Momentary: button presses toggle between

open and closed partition.

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS control units, Energi Savr Node systems, and GRX-IRPS transmitter / receiver pairs (through CCIs).

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Momentary Inputs: Input 1: toggles partition 1 open/closed Input 2: toggles partition 2 open/closed Input 3: toggles partition 3 open/closed Input 4: toggles partition 4 open/closed Input 5: toggles partition 5 open/closed Outputs: Maintained

Maintained Inputs: Contact closure opens partition; opening closes partition Input 1: opens/closes partition 1 Input 2: opens/closes partition 2 Input 3: opens/closes partition 3 Input 4: opens/closes partition 4 Input 5: opens/closes partition 5 Outputs: Maintained

Programming Instructions

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 1 will blink.

2. Wall 1 will be selected. To advance through the assigned walls, tap the Program button. To go to the previous wall, double-tap the Program button.

3. When the desired wall is selected, to assign the GRAFIK Eye QS control unit to that wall, press and hold the scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units to that wall; all control units assigned to that wall will work together when that wall is open.

4. Exit programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds.

Note: Occupancy sensors will not participate in partitioning logic.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

page 20

QSE-IO Control Interface Programming Guide

partitioning occ sensor

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Occupancy Sensor Mode

• Links to one or more GRAFIK Eye QS control units per I/O input.

• Allows communication so that an occupancy sensor can turn on the assigned areas, while still allowing scene changes once the room is occupied.

• 2 modes: Auto On–Auto Off

initiates events based on occupancy and / or vacancy Manual On–Auto Off initiates events based on vacancy

• Inputs: maintained only

• Outputs: maintained only.

• Communicates directly with GRAFIK Eye QS control units and wired occupancy sensors (through CCIs)

Special note: Each input represents one sensor or group of sensors. Response to the sensor event (on occupancy and vacancy) is programmable at the assigned lighting control device.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Auto On–Auto Off: Contact closure: Initiates occupancy event Contact opening: Initiates vacancy event Outputs: Maintained

Manual On–Auto Off: Contact closure: No event Contact opening: Initiates vacancy event Outputs: Maintained

Programming Instructions

Note: If multiple occupancy sensors are

programmed to control the same space, the ﬁrst sensor triggered will initiate the occupancy event, and all sensors must register vacancy to trigger the vacancy event.

1.Enter programming mode on the GRAFIK Eye QS control unit. Press and hold the top and bottom scene buttons for 3 seconds. The main menu will be displayed.

2.Navigate to and select occupancy sensor setup on the GRAFIK Eye QS menu (Sensor Setup > Occupancy > Setup). It will start searching for sensors.

3.Scroll through the list of sensors until the desired sensor is found. The screen will show the QSE-IO's serial number at the top, and CCI number (1-5) in the lower right corner.

4.Press the OK button and proceed to assign the sensor.

5.Exit programming mode on the GRAFIK Eye control unit. Press and hold the top and bottom scene buttons for 3 seconds.

Note: For more information and occupancy

settings, see "GRAFIK Eye QS Control Unit Installation and Operation Guide" at www.lutron.com

Note: Occupancy sensors will not participate in partitioning logic.

page 21

QSE-IO Control Interface Programming Guide

zone toggle

zone control

hotel conguration

345678

zone toggle

zone control

hotel conguration

345678

345678 345678

345678

zone toggle

zone control

hotel conguration

345678

345678 345678

345678

zone toggle

zone control

hotel conguration

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Zone Toggle Mode

• Links to one or more GRAFIK Eye QS control unit zones and/or Energi Savr Node zones.

• Toggles between Off and a user-preset zone level.

• Inputs: momentary only or maintained only, and correspond to either 5 independently controlled zones or groups of zones, or 3 independently controlled zones or groups of zones plus zone

- Maintained: closure turns zones on to preset

level(s); opening turns zone(s) off.

raise and lower (see chart).

- Momentary: closure toggles zone(s) between

preset level(s) and off; opening has no effect.

• Outputs: maintained.

• Communicates directly with GRAFIK Eye QS control units and Energi Savr Node systems.

Programming Instructions

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 1 will blink.

2.Zone Toggle input 1 will be selected. To advance through the inputs, tap the Program button. To go to the previous input, double-tap the Program button.

3.On the GRAFIK Eye QS control unit, use the raise and lower buttons for the zone you want to assign to the selected input on the QSE-IO control interface, and set the desired level. Then, press and release the raise and lower buttons together to assign that zone to the selected input on the QSE-IO control interface. Repeat this step for any other zones that you wish to be toggled by the selected input (on the same or any other GRAFIK Eye QS control units in the system). To unassign assigned zones, press and release the raise and lower buttons together.

4.Repeat steps 2 and 3 for each zone toggle input on the QSE-IO control interface.

5.Exit programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds.

For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Maintained Inputs: Closure turns zone on; opening turns zone off Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs: Maintained

Momentary Inputs: Closure toggles zone Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs: Maintained

Maintained Inputs: Closure turns zone on; opening turns zone off Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: raise last zone toggled Input 5: lower last zone toggled Outputs: Maintained

Momentary Inputs: Closure toggles zone Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: raise last zone toggled Input 5: lower last zone toggled Outputs: Maintained

page 22

QSE-IO Control Interface Programming Guide

zone control

hotel conguration

integration conguration

345678

zone control

hotel conguration

integration conguration

345678

345678 345678

345678

zone control

hotel conguration

integration conguration

345678

345678 345678

345678

zone control

hotel conguration

integration conguration

345678

345678 345678

345678

zone control

hotel conguration

integration conguration

345678

345678 345678

345678

zone control

hotel conguration

integration conguration

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Zone Control Mode

• Allows seeTouch wallstations, Pico wireless controls (via a QSM), QS keyswitches, or other QSE-IO control devices to toggle CCOs.

• Optionally, can additionally link to one or more GRAFIK Eye QS control unit zones and / or Energi Savr Node zones.

• CCIs toggle between Off and a user-preset zone level.

• Inputs: momentary only or maintained only, and correspond to 5 independently controlled zones or groups of zones.

- Maintained: closure turns zones on to preset

level(s); opening turns zone(s) off.

- Momentary: closure toggles zone(s) between

preset level(s) and off; opening has no effect.

• Outputs:

- Maintained only

(button press on input device toggles output)

- Momentary only

(button press on input device triggers momentary pulse)

- Pulsed only

(CCO status follows activating button status, where if button is released, CCO is open, and if button is pressed, CCO is closed).

• Communicates directly with seeTouch wallstations, Pico wireless controls (via a QSM), QS keyswitches, or other QSE-IO control devices.

Special note: "Momentary" output pulse is of ﬁxed duration (250 ms default). "Pulsed" output pulse duration corresponds to activating button being held / released.

(continued on next page)

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Maintained Inputs, Maintained outputs: Closure turns zone on; opening turns zone off Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs toggled by QS input devices

Maintained Inputs, Momentary output: Closure turns zone on; opening turns zone off Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs pulsed by QS input devices

Maintained Inputs, Pulsed output: Closure turns zone on; opening turns zone off Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs pulsed by QS input devices

Momentary input, Maintained output: Closure toggles zone Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs toggled by QS input devices

Momentary input, Momentary output: Closure toggles zone Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs pulsed by QS input devices

Momentary input, Pulsed output: Closure toggles zone Input 1: toggle preset level 1/Off Input 2: toggle preset level 2/Off Input 3: toggle preset level 3/Off Input 4: toggle preset level 4/Off Input 5: toggle preset level 5/Off Outputs pulsed by QS input devices

page 23

QSE-IO Control Interface Programming Guide

Zone Control Mode (continued)

Programming Buttons on QS Input Devices to the CCOs

seeTouch QS Wallstation Note: Wallstation must be set up for zone toggle

mode; see the instructions that accompanied your wallstation for instructions.

1. Enter programming mode on the wallstation: Hold the top and bottom buttons for 5 seconds.

2. Press the button on the wallstation that you wish to program.

3. On the QSE-IO control device, tap the Program button to advance through the CCOs (the LED for the selected CCO will blink rapidly). When you have reached the CCO that you wish to assign to the selected button on the wallstation, press and hold the Program button on the QSE-IO control device for 5 seconds, then release. The LED will ﬂash to conﬁrm assignment.

4. To unassign an assigned CCO, select that CCO as above, and press and hold the Program button on the QSE-IO control device for 5 seconds.

5. Repeat steps 3 and 4 for any other CCOs you wish to assign to this wallstation button.

6. Repeat steps 2 through 5 to program additional buttons on the wallstation.

7. Exit programming mode: Press and hold the top and bottom buttons on the wallstation for 5 seconds.

QS Keyswitch Note: Keyswitch must be set up for zone toggle

mode; see the instructions that accompanied your keyswitch for instructions.

1. Enter programming mode on the keyswitch: press and hold its Program button for 5 seconds. (You must remove the faceplate and faceplate adapter to access the Program button.)

2. On the QSE-IO control device, tap the Program button to advance through the CCOs (the LED for the selected CCO will be blink rapidly). When you have reached the CCO that you wish to assign to the selected button on the wallstation, press and hold the Program button on the QSE-IO control device for 5 seconds. The LED will ﬂash to conﬁrm assignment.

3. To unassign an assigned CCO, select that CCO as above, and press and hold the Program button on the QSE-IO control device for 5 seconds.

4. Repeat steps 3 and 4 for any other CCOs you wish to assign to this keyswitch.

5. Exit programming mode: Press and hold the Program button on the keyswitch for 5 seconds. Replace the Faceplate adapter and faceplate on the keyswitch.

CCI on a Different QSE-IO Control Device Note: On the control device to be programmed,

the DIP switches must be in Zone Toggle conﬁguration to toggle a CCO on a control device in Zone Control conﬁguration. If correctly applied, this programming mode can be used to translate maintained signals into momentary, or vice versa.

1. Enter programming mode on the Zone Toggle QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 1 will blink.

2. CCI1 will be selected. To advance through the inputs, tap the Program button. To go to the previous input, double-tap the Program button.

3. On the Zone Control QSE-IO control interface, tap the Program button to advance through the CCOs (the LED for the selected CCO will blink rapidly). When you have reached the CCO that you wish to assign to the selected CCI, press and hold the Program button on the Zone Control QSE-IO control device for 5 seconds. The LED will ﬂash to conﬁrm assignment.

4. To unassign an assigned CCO, select that CCO as above, and press and hold the Program button on the QSE-IO control device for 5 seconds.

5. Repeat steps 3 and 4 for any other CCOs you wish to assign to this CCI on the Zone Toggle QSE-IO control interface.

6. Repeat steps 2 through 5 to program additional CCIs on the Zone Toggle QSE-IO control device.

7. Exit programming mode on the Zone Toggle QSE-IO control interface: Press and hold the Program button for 3 seconds.

(continued on next page)

page 24

QSE-IO Control Interface Programming Guide

Zone Control Mode (continued)

Programming Instructions (continued)

Pico Wireless Control Note: Pico wireless control must already be

associated to a QSM and must have been set as Zone type (this is the default type). Refer to the QSM documentation for programming instructions. A Pico control device programmed as a Zone type can be assigned to one or more CCOs. All buttons on the Pico control device affect the same CCO or group of CCOs. However, any button on the Pico control device can be programmed to take any of its assigned CCOs to any state (Open or Close).

1. Enter programming mode on the Pico wireless control: press and hold the top and bottom buttons for 5 seconds.

2. Press the button on the Pico wireless control that you wish to program. (Raise/Lower buttons need not be programmed.)

- CCOs on the QSE-IO control device that are

already programmed to Close when this button is pushed will have their LEDs constantly on.

- CCOs on the QSE-IO control device that are

already programmed to Open when this button is pushed will have their LEDs ﬂashing slowly (once per second).

- CCOs that are not programmed to do anything

when this button is pushed will have their LEDs constantly off.

3. On the QSE-IO control device, tap the Program button to advance through the available states that can be programmed to correspond to button presses on the Pico wireless control. To go to the previous state, double-tap the Program button.

- State A (Initial state): No action. All LEDs are Off.

- State B: CCO1 Open

LED1 alternates between ﬂashing rapidly and Of f.

- State C: CCO1 Close

LED1 alternates between ﬂashing rapidly and On.

- State D: CCO2 Open

LED2 alternates between ﬂashing rapidly and Of f.

- State E: CCO2 Close LED2 alternates between ﬂashing rapidly and On.

- State F: CCO3 Open LED3 alternates between ﬂashing rapidly and Of f.

- State G: CCO3 Close LED3 alternates between ﬂashing rapidly and On.

- State H: CCO4 Open LED4 alternates between ﬂashing rapidly and Of f.

- State I: CCO4 Close LED4 alternates between ﬂashing rapidly and On.

- State J: CCO5 Open LED5 alternates between ﬂashing rapidly and Of f.

- State K: CCO5 Close LED5 alternates between ﬂashing rapidly and On.

4. Press and hold the Program button on the

QSE-IO control device for 5 seconds to complete the assignment. The selected LED will blink rapidly to conﬁrm the assignment. Note: If this is the ﬁrst time you are assigning this combination of CCO and Pico wireless control, the QSE-IO control device will automatically assign that CCO to all the other buttons on the Pico wireless control (using default settings).

5. To unassign an assigned CCO, select that CCO

as above, and press and hold the Program button on the QSE-IO control device for 5 seconds. The selected LED will blink rapidly to conﬁrm the unassignment. Note that the CCO will automatically be unassigned from all buttons on the Pico wireless control.

6. Repeat steps 3 through 5 for any other CCOs you

wish to assign to the selected button.

7. Repeat steps 2 through 6 for additional buttons.

8. Exit programming mode: Press and hold the top

and bottom buttons on the Pico wireless control.

page 25

(continued on next page)

QSE-IO Control Interface Programming Guide

Zone Control Mode (continued)

Programming Instructions (continued)

CCOs Follow GRAFIK Eye QS Zones

Each CCO can be set up to be controlled by a GRAFIK Eye QS zone.

Note: To be assigned to a CCO, a GRAFIK Eye QS control unit must ﬁrst be set to the "Remote Non-Dim" load type. A GRAFIK Eye QS zone can be mapped to only one CCO.

1. Enter programming mode on the GRAFIK Eye QS control unit: Press and hold the top and bottom scene buttons for 3 seconds. The LEDs in the scene buttons will scroll from top to bottom, and the info screen will display the main menu.

2. Use the Master buttons to the right of the screen to navigate to the "Remote Zone" menu, and press the OK button.

3.On the GRAFIK Eye QS control unit, press the raise or lower button for the zone you want to assign to the selected output on the QSE-IO control interface.

4.On the QSE-IO control interface, repeatedly press the Program button until the LED for the CCO you want to assign to with the zone is ﬂashing.

5. Press and hold the Program button on the QSE-IO control interface for 5 seconds to complete the assignment.

6. To unassign a CCO, repeat steps 4 and 5 with an assigned CCO.

7. Repeat steps 3 through 6 to assign/unassign GRAFIK Eye QS zones to additional CCOs.

7. Exit programming mode on the GRAFIK Eye QS control unit: Press and hold the top and bottom scene buttons simultaneously for 3 seconds. The info screen will go to Scene 1.

CCIs Toggle GRAFIK Eye QS and Energi Savr Node Zones

Note: On the control device to be programmed, the DIP switches must be in Zone Toggle conﬁguration. DIP switch 1 must be down (Off).

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 1 will blink.

2. CCI1 will be selected. To advance through the inputs, tap the Program button. To go to the previous input, double-tap the Program button.

3.On the GRAFIK Eye QS control unit, use the raise and lower buttons for the zone you want to assign to the selected input on the QSE-IO control interface, and set the desired level. Then, press and release the raise and lower buttons together to assign that zone to the selected input on the QSE-IO control interface. Repeat this step for any other zones that you wish to be toggled by the selected input (on the same or any other GRAFIK Eye QS control units in the system). To unassign assigned zones, press and release the raise and lower buttons together.

4.Repeat steps 2 and 3 for each zone toggle input on the QSE-IO control interface.

5. Repeat steps 3 and 4 for any other zones you wish to assign to this CCI on the QSE-IO control interface.

6. Repeat steps 2 through 5 to program additional CCIs on the QSE-IO control device.

7. Exit programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

page 26

(continued on next page)

QSE-IO Control Interface Programming Guide

Zone Control Mode (continued)

Programming Instructions (continued)

CCIs Toggle CCOs on the same QSE-IO Control Device

Note: On the control device to be programmed, the DIP switches must be in Zone Toggle conﬁguration. DIP switch 1 must be up (On). If correctly applied, this programming mode can be used to translate momentary signals into maintained, or vice versa.

If needed, it is possible to program the same CCIs to GRAFIK Eye QS zones, Energi Savr Node zones, and / or local CCOs on the same QSE-IO control device.

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 1 will blink.

2. Toggle or pulse a CCI to select it. If no equipment is connected to the CCI, this can be accomplished by momentarily connecting a jumper wire between that CCI and CCI COMMON.

3. To advance through the CCOs, tap the Program button. To go to the previous CCO, double-tap the Program button.

4. Press and hold the Program button to assign the selected CCO to the selected CCI.

5. Repeat steps 3 and 4 for any additional CCOs you wish to assign to the selected CCI.

6. Repeat steps 2 through 5 to select additional CCIs to complete your desired assignments.

7. Exit programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds.

page 27

QSE-IO Control Interface Programming Guide

hotel conguration

integration conguration

345678

hotel conguration

integration conguration

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

345678 345678

345678

hotel conguration

integration conguration

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

345678 345678

345678

hotel conguration

integration conguration

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

345678 345678

345678

hotel conguration

integration conguration

shade stuffs

partitioning occ sensor

345678

345678 345678

345678

345678 345678

345678

integration conguration

shade stuffs

partitioning occ sensor

345678

Hotel Mode

• Links to one or more GRAFIK Eye QS control units and/or Energi Savr Node areas.

• Accepts inputs from seeTouch QS wallstations, Pico wireless control devices (through a QSM), QS keyswitches, or other QSE-IO control devices, allowing the mode to toggle between Service (make up room) and Privacy (do not disturb), as

• Allows interface with hotel room equipment. Toggles outputs; Afterhours Mode; Scene 1 and

well as to ring a doorbell.

Off scene; or Scene Lockout (see chart).

• Inputs: maintained (input 3 is momentary).

• Outputs: maintained or momentary.

• Communicates directly with seeTouch wallstations, Pico wireless controls (via a QSM), QS keyswitches, or other QSE-IO control devices.

• Inputs 4 (Start/End Afterhours) and 5 (Scene 1/Off, or Scene Lockout) are designed to be wired to a hotel room keycard holder (input 4 recommended), or third-party contact closure signals from the hotel reception desk at check-in and check-out (input 5 recommended). When a GRAFIK Eye QS control unit or Energi Savr Node area is in Afterhours mode, the lights will turn off after a programmable timeout (default is 5 minutes). If a button is pushed, turning the lights back on while in Afterhours mode, the lights will once again go off after a separate programmable timeout (default is 45 minutes). Before turning off, the lights ﬂash to warn any occupant in the space. When Afterhours mode is ended, this behavior stops and the lights return to their previous state.

Special note: "Service" and "Privacy" will automatically mutually exclude each other. "Doorbell" is blocked when "Privacy" is active.

Programming Instructions

Programming Buttons on a seeTouch QS Wallstation to CCOs 1, 2 and 3 (Service, Privacy and Doorbell)

Notes

• Wallstation must be set up for zone toggle mode; see the instructions that accompanied your wallstation.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Mode 1: Input 1: toggle output 1 Input 2: toggle output 2 Input 3: pulse output 3 Input 4: start/end Afterhours mode Input 5: toggle Scene 1/Off

Mode 2: Input 1: toggle output 1 Input 2: toggle output 2 Input 3: pulse output 3 Input 4: start/end Afterhours mode Input 5: enable/disable Scene Lockout

Standard Usage: Output 1: Service (make up room) Output 2: Privacy (do not disturb) Output 3: Doorbell

Outputs 1 and 2 are mutually exclusive Output 2 active disables Output 3

Either Input 4 or Input 5 (not both) can be active; the other must be disabled

DIP switch 1 up (on): Input 4 activated DIP switch 1 down (off): Input 4 disabled DIP switch 2 up (on): Input 5 activated DIP switch 2 down (off): Input 5 disabled

• Due to the mutually exclusive nature of the Service, Privacy, and Doorbell CCOs, a given button on the wallstation can be programmed to only one of the three CCOs. However, multiple buttons may be programmed to the same CCO.

1. Enter programming mode on the wallstation: Hold the top and bottom buttons for 5 seconds.

2. Press the button on the wallstation that you wish to program.

3. On the QSE-IO control device, tap the Program button to advance through CCOs 1, 2, and 3 (the LED for the selected CCO will blink rapidly). When you have reached the CCO that you wish to assign to the selected button on the wallstation, press and hold the Program button on the QSE-IO control device for 5 seconds. The LED will ﬂash to conﬁrm assignment.

4. To unassign an assigned CCO, select that CCO as above, and press and hold the Program button on the QSE-IO control device for 5 seconds.

5. Repeat steps 2 through 4 to program additional buttons on the wallstation.

6. Exit programming mode: Press and hold the top and bottom buttons on the wallstation for 5 seconds.

page 28

QSE-IO Control Interface Programming Guide

Hotel Mode (continued)

Programming Instructions (continued)

Programming Buttons on a Pico Wireless Control to CCOs 1, 2, and 3 (Service, Privacy and Doorbell)

Notes

• The Pico wireless control must already be associated to a QSM and must have been set as Zone type (the default type). Refer to the QSM documentation for programming instructions.

• A Pico wireless control programmed as a Zone type can be assigned to either:

- CCO1 (Service) and CCO2 (Privacy) together,

where the top button of the Pico will command "Service" and the bottom button will command "Privacy" (2 button Pico wireless control recommended)

- CCO3 (Doorbell), where the middle button of the

Pico wireless control will ring the doorbell (unless the Privacy signal is asserted)

1. Enter programming mode on the Pico wireless control: Press and hold the top and bottom buttons for 5 seconds.

2. On the QSE-IO control device, tap the Program button to advance through CCOs 1, 2, and 3 (the LED for the selected CCO will blink rapidly). When you have reached the CCO that you wish to assign to the Pico wireless control, press and hold the Program button on the QSE-IO control device for 5 seconds. The LED will ﬂash to conﬁrm assignment.

3. To unassign an assigned CCO, select that CCO as above, and press and hold the Program button on the QSE-IO control device for 5 seconds. The selected LED will blink rapidly to conﬁrm the unassignment.

4. Exit programming mode: Press and hold the top and bottom buttons for 5 seconds.

Programming CCIs 4 and 5 to a GRAFIK Eye QS Control Unit or an Energi Savr Node Unit

1. Enter programming mode on the QSE-IO control interface: Press and hold the Program button for 3 seconds. LED 4 will blink.

2. Input 4 will be selected. To select between Input 4 and Input 5, tap the Program button.

3. When the desired input is selected, to assign the GRAFIK Eye QS control unit to that input, press and hold the Scene 1 button on the GRAFIK Eye QS control unit for 3 seconds. Repeat to assign additional GRAFIK Eye QS control units to that input.

4. Press and hold the Program button on the QSE-IO control interface for 3 seconds to exit programming mode.

Note: For programming instructions for Energi Savr Node systems, see "Energi Savr Node Handheld Programming Guide" at www.lutron.com

page 29

QSE-IO Control Interface Programming Guide

integration conguration

shade stuffs

partitioning occ sensor

345678

Integration Mode

• Allows a QSE-CI-NWK-E control device to communicate with contact closure based third-party equipment.

• Inputs: momentary or maintained.

• Outputs: momentary or maintained.

• Communicates directly with a QSE-CI-NWK-E control device.

Programming Instructions

No programming is necessary. See the Lutron Integration Protocol document (P/N 040249) at www.lutron.com for supported commands.

Dip Switch Settings Related Action

345678

Legend:

Up/On

Down/Off

Input 1: notify QSE-CI-NWK-E Input 2: notify QSE-CI-NWK-E Input 3: notify QSE-CI-NWK-E Input 4: notify QSE-CI-NWK-E Input 5: notify QSE-CI-NWK-E

page 30

QSE-IO Control Interface Programming Guide

R

Internet: www.lutron.com/support E-mail: support@lutron.com

World Headquarters

USA Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18 0 36 -129 9

TEL +1.610.282.3800 FA X +1.610 . 28 2.124 3 Customer Assistance: 1.844.LUTRON1 North and South America Technical Hotlines USA, Canada, Caribbean: 1.844.LUTRON1 (1.844. 588.7661) Mexico: +1.888.235.2910 Central / South America: +1.610.282.6701

UK and Europe Lutron EA Limited 125 Finsbury Pavement 4th ﬂoor, London EC2A 1NQ United Kingdom

TEL +44.(0)20.7702.0657 FAX +44.(0)20.7480.6899 FREEPHONE (UK) 0800.282.107 Technical support +44.(0)20.7680.4481

Asia Lutron GL Ltd. 390 Havelock Road #07-04 King's Centre Singapore 169662

TEL +65.6220.4666 FAX +65.6220.4333

Asia Technical Hotlines Northern China: 10.800.712.1536 Southern China: 10.800.120.1536 Hong Kong: 800.901.849 Indonesia: 001.803.011.3994 Japan: +81.3.5575.8411 Macau: 0800.401 Singapore: 800.120.4491 Taiwan: 00.801.137.737 Thailand: 001.800.120.665853 Other countries: +65.6220.4666

The Lutron logo, Lutron, Sivoia, seeTouch, Pico, Quantum, Energi Savr Node, and GRAFIK Eye are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. © 2012-2021 Lutron Electronics Co., Inc.

P/N 040391 Rev D 03/2021

page 31

Lutron QSE-IO User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual