Page 1
Pico PX Series Wired Control
1
369439e 1 10.01.20
Pico Wired Control
The Pico wired control works with compatible
Lutron systems to control a light or group of lights.
The Pico wired control is easily wired to the system
via IEC PELV / NECR Class 2 wiring.
Features
•
Provides control for the following Lutron products
that incorporate a wired IR input:
– Energi Savr Node units
– QS sensor modules
– EcoSystem ballasts or ballast modules
•
Mounts easily in any single-gang wallbox (sold separately)
•
Fits designer style Claro wallplates (sold separately)
•
Allows users to:
—
Turn On / Off individual fixture or group of fixtures
—
Raise / Lower light levels (-2BRL and -3BRL)
—
Recall favorite light levels (-3B and -3BRL)
•
IEC PELV / NECR Class 2 wiring
Model Numbers
PX-2B-GXX*-I01 2 Buttons
PX-2BRL-GXX*-I01 2 Buttons with Raise/Lower
PX-3B-GXX*-I01 3 Buttons (including Preset)
PX-3BRL-GXX*-I01 3 Buttons (including Preset)
with Raise/Lower
* “XX” in the model number represents color code.
Color and Finishes
White
WH
Black
BL
Ivory
IV
White / Gray
WG
Light Almond
LA
PX-2BRL-GWH-I01
Shown actual size with Claro wallplate
(sold separately)
PX-3BRL-GWH-I01 PX-3B-GWH-I01 PX-2B-GWH-I01
Models shown in White (WH)
Notes:
•
All models available in gloss finish only.
•
For White/Gray (WG), top and raise buttons are white; preset, lower, and bottom buttons are gray.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Page 2
Pico PX Series Wired Control
2
369439e 2 10.01.20
Specifications
Regulatory
•
Designed for IEC PELV/NECR Class 2 operation only
•
Complies with requirements of NFPA 70, of the
National Electrical CodeR IEC PELV/NECR Class 2
device wiring
•
Install according to all applicable national and local
wiring regulations
•
For regions requiring ULR listing on low-voltage devices,
install in a fully enclosed wallbox. Low- voltage wallboxes
are acceptible for regions that do not require ULR listing
on low-voltage devices
Power
•
Do not exceed 35 V-
•
Operating Voltage: 20 V- (IEC PELV/NECR Class 2)
•
Current Draw: 20 mA maximum
System Communication and Capacity
•
Total wire length from control to device must not
exceed 500 ft (152 m)
•
Not a wireless device
Mounting
•
Mounts easily in any single-gang wallbox (not included)
•
Lutron suggests using Lutron Claro wallplates to ensure
proper compatibility. Wallplates sold serparately. Pico
wired controls may not be compatible with non-Lutron
wallplates, test fit non-Lutron parts before use.
Wiring
•
Pico wired control does not receive IR input from
hand-held transmitters
•
Pico wired control does not connect to QS Link
•
A Pico wired control can only be wired to a single
control module or a single sensor interface
•
Each input on a control module or sensor interface can
be connected to only one control or one input device
Red = 20 V-
Black = Common
White/Red = IR Signal (IR input terminal of ballast or module)
NOTE: The red stripe on this wire may be absent in older products
or in retrofit applications.
Warranty
1-year limited warranty
For additional Warranty information, please visit
www.lutron.com/TechnicalDocumentLibrary/
369-119_Wallbox_Warranty.pdf
Environment
•
Temperature: 32 ºF to 104 ºF (0 °C to 40 °C)
•
Relative Humidity: Less than 90% non-condensing
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Page 3
Pico PX Series Wired Control
3
369439e 3 10.01.20
Operation
The basic functionality of the Pico wired control is detailed below. For specific system performance, reference
system documentation at www.lutron.com, or contact your Lutron representative.
Top Button
Lights brighten to full intensity.
Preset Button
(3B & 3BRL models only)
Tap once:
Lights go to preset levels.
Raise Button (2BRL & 3BRL models only)
Lights increase in intensity.
Lower Button (2BRL & 3BRL models only)
Lights decrease in intensity.
Dimensions
Measurements shown as:
4.69
(119)
in
(mm)
1.98
(50)
Bottom Button
Lights dim to off.
Mounting
Wallplate and wallplate adapter sold separately.
Claro
wallplate
Pico
Wired
control
2.94
(75)
)Lutron, Lutron, Pico, Energi Savr Node, EcoSystem and Claro are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
All other product names, logos, and brands are property of their respective owners.
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
0.31
(7.8)
Model Numbers:
Wallplate
adapter
Loading...