Lutron Pd-fsqn User Manual
Wireless
Lutron
quick-start guide
In-wall fan control
Welcome—and thank you for purchasing a Caséta
Wireless in-wall fan control. In order to control your
ceiling fan from an app or remote, you’ll need to replace
an existing switch with a Caséta Wireless in-wall fan
control.
Before you install the fan control, please read quick-start
guide and watch the installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of Caséta Wireless!
Double your warranty
Love Caséta Wireless controls? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
Contents supplied
In-wall fan control
(PD-FSQN)
Wire connectors (3)
Screws (2)
Installing your fan control
Install the fan
1
Install the fan according to the manufacturer’s
instructions and ensure proper operation.
Set the fan speed and the lights
2
Set the fan to the highest speed using the pull chains.
Turn power off at circuit breaker!
3
OFF
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
Important note:
Some fans have one wall switch, while others
have two or more wall switches. We’ve included
instructions for fans with one wall switch (called a
single pole). If your fan has more than one switch
(called a 3-way), please visit
www.casetawireless.com/3way for complete
installation instructions and how-to videos.
Remove existing switch from wall
4
Remove the wallplate from switch.
Remove the switch and pull it away from the wall.
Place tag on load wire. Disconnect all three
wires* from the switch.
7
1
2
3
4
5
6
Ground
Tag
Installation for ceiling fans with one wall switch (single pole)
Remove side sections (if necessary)
5
Bend back
and forth.
Do not remove outside side sections
on the controls at the end of gang.
Each control
has inside side
sections removed.
Control at middle has all
side sections removed.
Connect the fan control
6
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the fan control
using a wire connector.
2 Wrap line/hot wire around screw terminal. Tighten
securely to 5 in-lb (0.55 N•m)
3 Connect the neutral wire from the wallbox to the
white wire on the fan control using a wire connector.
4 Connect the load wire from the wallbox to the yellow
wire on the fan control using a wire connector.
Mount the fan control
7
Use the screws provided.
4
3
2
1
Tag
Ground
Attach the wallplate
8
Attach the adapter to the fan control using the
screws provided and snap on the wallplate.
1
2
3
‘snap’
(If you installed the control next to other dimmers,
switches, or controls, you’ll need to install a wallplate
with the correct size/number of openings to
accommodate all the devices)
Turn power on at circuit breaker
9
CAUTION
Use only with permanently installed ceiling fans. To
avoid overheating and possible damage to other
equipment, do not use to control receptacles, motordriven appliances, or transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Tools you’ll need
Flat-head screwdriver
Phillips-head screwdriver
Pliers
P/N 0301907 REV A
Works with one paddletype ceiling fan:
Fan—up to 1.5 A
IMPORTANT NOTES
1. Use to control one paddle-type ceiling fan
(permanent split-capacitor).
2. Use the ceiling fan’s pull chain to set its speed to
the highest setting.
3. Do not use to control fans that use shaded-pole
motors (i.e. bath exhaust fans).
4. Do not use to control fans that have integrated
fan speed controls (i.e. fans that have a remote
control), unless the integrated control is removed
from the ceiling fan.
5. Do not connect to any other motor-operated
appliance or to any lighting load type.
6. Do not use to control a fan lighting load (i.e.
light kit).
7. Do not use to control DC motor fans.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Tag
Ground
* If your switch has more than 3 wires attached, see
“Installing Caséta Wireless in a 3-way switch application”
video at www.casetawireless.com/3way
Using your Caséta Wireless kit (sold separately)
With a smartphone or tablet (Bridge required, sold separately)
The Caséta Wireless fan control can be controlled from a
smartphone when used with the Lutron Smart Bridge.
If you are using the fan control and remote control with the Lutron
Smart Bridge follow the instructions below.
Note: If you are using the fan control and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
Lutron Smart Bridge
Download the Lutron app
1 Press and hold “off” button on dimmer
Search for “Lutron Caseta”
www.casetawireless.com/LutronApp
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Launch the Lutron app
Press and hold “off” button on remote
2
The Lutron app will walk you through
setting up your devices.
Lutron
Press and hold “off” button on remote
Use the Lutron app to complete ALL remaining steps
3
Add devices
•Picoremotes
•Dimmers
•Shades
•Switches
•Fancontrols
Control
three ways
Lutron
Schedule
your lights,
fans, or loads
Lutron app
Connect
while away
1
2
Without a smartphone or tablet (Bridge not required)
Pairing the fan speed control
and Pico remote control
Press and hold “off” button on the fan
1
control
Hold for 6 seconds
until LEDs start
blinking
Press and hold “off” button
2
Hold for 6 seconds
until fan control LEDs
flash 3 times.
x3
Repeat steps to pair other
Pico remote controls.
For advanced features, tips for using Caséta Wireless products, the complete Caséta Wireless product line, and more,
please visit www.casetawireless.com/features
Changing the favorite fan speed
setting on the Pico remote
control or fan control (sold
separately)
You can use the round “favorite”
button on the Pico remote control
or fan control to recall a favorite
fan speed setting. We’ve set it to
Medium, but you can change it to
any speed you like.
Set desired fan speed setting on fan
3
control
Press and hold “favorite” button on remote
4
Hold the favorite button on
either the remote or control
for 6 seconds until LEDs
blink twice on in-wall fan
control. New favorite level is
now saved.
x2
Favorite
ON
Using your controls
On
Faster
Favorite
Slower
Off
FASS
Front Accessible
Service Switch
In-wall fan
control
On
Faster
Favorite
Slower
Off
Pico remote control (sold separately)
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Device Ratings
In-wall fan control
PD-FSQN
120 V~ 50/60 Hz
1.5 A
Troubleshooting
Symptoms Probable cause and action
Fan does not
turn ON and no
indicator lights
turn ON.
Fan does not
work.
Fan vibrates or
wobbles.
Fan speed is too
slow.
Go to www.casetawireless.com/support for
additional troubleshooting suggestions.
)Lutron Lutron, Caséta and Pico are trademarks of Lutron Electronics
Co., Inc., registered in the U.S. and other countries. FASS and
Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a
registered trademark of the National Fire Protection Association, Quincy,
Massachusetts. Google and the Google logo are registered trademarks of
Google Inc., used with permission.
© 2018 Lutron Electronics Co., Inc
P/N 0301907 REV A
• Ensure Front Accessible
Service Switch (FASS) is fully
pushed in to the ON position.
• Ensure that the fan pull chain is
set to highest possible setting.
• Neutral wire is not connected.
Check wiring.
• Breaker is OFF or tripped (or
fuse blown). Reset breaker
or replace fuse. If condition
persists, contact Lutron
Customer Assistance or a
licensed electrician.
• Load and Line wires possibly
reversed, refer to wiring
diagram in step 6.
Fan direction switch is between
forward and reverse. Set switch
to desired position.
• Fan direction switch is between
forward and reverse. Set switch
to desired position.
• Fan blades must be balanced.
See fan manufacturers
installation guide to balance
fan.
Set fan pull chain speed to high.
Loading...