Lutron PD-10NXD, PD-3PCL, PD-5NE, PD-6WCL Specification Sheet
®
CasétaR Wireless Load Controls
1
369987a 1 09.09.16
CasétaR Wireless Load Controls
The CasétaR Wireless family of Dimmers and
Switches can be controlled directly and remotely
when paired with PicoR Remote Controls providing
a system that delivers convenience and ease of
installation.
CasétaR Wireless Dimmers and Switches use
LutronR patented Clear ConnectR RF Technology
which enables wireless communication with PicoR
Remote Controls and the LutronR Smart Bridge and
Smart Bridge PRO.
Features
CasétaR Wireless
In-Wall Switch
CasétaR Wireless
In-Wall Dimmer
• Works with PicoR Remote Control
• Works with the LutronR App (via a Smart Bridge or
Smart Bridge PRO)
1
• LutronR patented Clear ConnectR RF Technology
works through walls and floors
• Includes Front Accessible Service Switch (FASST)
for safe lamp replacement
• Works with LutronR Radio Powr SavrT Occupancy
and Vacancy Sensors in standalone applications
(sensors do not work with Smart Bridge or Smart
Bridge PRO)
CasétaR Wireless
ELV+ Dimmer
CasétaR Wireless
Plug-In Lamp Dimmer
Note: Certain models or load types will require a neutral connection. (see Load Types and Capacity sections)
1
The Lutron® App is required for setup and usage with the Smart Bridge and Smart Bridge PRO. The LutronR App is compatible with iOSR devices version 8.0
or later and AndroidT devices 4.0 or later.
iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license.
Android is a trademark of Google Inc.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
®
CasétaR Wireless Load Controls
2
369987a 2 09.09.16
Specifications
Regulatory Approvals
• cULus Listed
• NOM Certified
• FCC Approved. Complies with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules
• Industry Canada Certified
• IFTEL Certified
• NEMA 410 (-6ANS, -5WS, -10NXD, and -5NE)
Power
Operating voltage:
• 120 V~ 50/60 Hz: -3PCL, -6WCL, -10NXD, -6ANS,
-5NE
• 120 / 277 V~ 50 / 60 Hz: -5WS-DV
Key Design Features
• Tested to withstand electrostatic discharge without
damage or memory loss, in accordance with
IEC 61000-4-2.
• Tested to withstand surge voltages without damage
or loss of operation, in accordance with IEEE
C62.41-1991 Recommended Practice on Surge
Voltages in Low-Voltage AC Power Circuits.
• Load controls always operate locally and do not
require system control.
• Power failure memory: should power be interrupted,
the control will return to its previously set level prior
to the interruption when power is restored.
• PD-5WS-DV, PD-6ANS, and PD-10NXD use
conventional 3-way wiring.
• Uses LutronR ClaroR Wallplates or designer-style
wallplates from other manufacturers. Wallplates are
sold separately.
• LutronR ClaroR Wallplates snap on with no visible
means of attachment.
1
• Requires a 1-gang U.S. wallbox. 3
1
depth recommended, 2
⁄4 in (57 mm) depth
⁄2 in (89 mm)
minimum.
• Green status LED(s) to indicate load status.
System Communications and Capacity
• CasétaR Wireless In-Wall Switches and Dimmers
communicate with PicoR remote controls and the
LutronR Smart Bridge/Smart Bridge PRO through
Radio Frequency (RF).
• The CasétaR Wireless In-Wall Switches and Dimmers
communicate with LutronR Radio Powr SavrT
Occupancy and Vacancy
Sensors in a standalone
application. Sensors do not work with Smart Bridge
or Smart Bridge PRO.
• The CasétaR Wireless In-Wall Switches and Dimmers
must be located within 60ft (18m) line-of-sight or
30ft (9m) through walls, of PicoR remote controls
and LutronR Smart Bridge devices.
Device limits
• PicoR Remote Controls and Radio Powr SavrT
Occupancy Sensors: up to 10devices (total) may
be paired to each CasétaR Wireless In-Wall Switch/
Dimmer (with no Smart Bridge installed).
• Smart Bridge or Smart Bridge PRO system: up to
50total wireless devices (CasétaR Wireless Dimmers/
Switches, PicoR Remote Controls, and Shades) are
supported per system. Smart Bridge or Smart Bridge
PRO counts as one device.
Environment
• Ambient operating temperature: 32°F to 104°F
(0°C to 40°C), 0% to 90% humidity,
non-condensing. Indoor use only.
• PD-5WS-DV, PD-6ANS, and PD-10NXD can be used
with mechanical switch in 3-way applications.
SPECIFICATION SUBMITTAL Page
Job Name:
Job Number:
Model Numbers:
®
CasétaR Wireless Load Controls
3
369987a 3 09.09.16
Features
Simple two-wire installation (no neutral
wire required)
Capable of dimming loads
Favorite button (user defined one touch
light level)
Works with Hi-lumeR 1% 2-Wire LED
Drivers (Forward-phase only)
Works with Power Interfaces (PHPM and
GRX TVI)
Works with Power Interfaces (PHPM-SW)
No wiring required
PRO Dimmer
PD-10NXD
1
√
Plug-In
Dimmer
PD-3PCL
In-Wall
Dimmer
PD-6WCL
ELV+
Dimmer
PD-5NE
√ √
2-wire Switch
PD-5WS-DV
√ √ √ √
√
√ √ √ √
√ √
√
Neutral
Switch
PD-6ANS
√
1
In some low-wattage applications the PD-10NXD will require a neutral wire connection.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
®
CasétaR Wireless Load Controls
4
369987a 4 09.09.16
Load Type and Capacity - Switches
Model Number Description Voltage Load Type Minimum Load
120 V~
277 V~
Incandescent /
Halogen
Incandescent /
Halogen
25 W 600 W 450 W 350 W
25 W 135 0 W 110 0 W 800 W
Maximum Load
Not Ganged End of Gang Middle of Gang
3
120 V~ MLV 25 W 600 VA /475 W 450 VA / 350 W 350 VA / 275 W
PD-5WS-DV
1
Two -w ire
switch
277 V~ MLV 25 W 1350 VA /1075 W 1100 VA / 875 W 800 VA / 625 W
120 V~
120 / 277 V~ LED Use LUT-MLC
120 / 277 V~ Fluorescent U s e LUT- M LC
120 V~ ELV Use LU T- ML C
277 V~ ELV Us e L U T- M L C
General
Purpose Fan
Incandescent /
Halogen
0.4 A 3 A 3 A 3 A
2
5 A 4 A 3 A
2
5 A 4 A 3 A
2
600 W 450 W 350 W
2
135 0 W 110 0 W 800 W
10 W 720 W 720 W 600 W
MLV 10 W 720 VA 720 VA 60 0 VA
Neutral-wire
PD-6ANS
switch
(neutral
connection
required)
120 V~
Fan 0.1 A 3.6 A 3.6 A 3.6 A
LED 1 bulb 6 A 6 A 5 A
Fluorescent 1 ballast 6 A 6 A 5 A
ELV 10 W 720 VA 720 VA 600 VA
PHPM-SW 1 inter face 3 interfaces 3 interfaces 3 interfaces
1
No neutral wire required.
2
To ensure proper operation of the switch with LED, fluorescent, and ELV loads, a LUT-MLC may be required, especially at lower wattages. If the status LED
on the switch is flashing or solid red in color, a LUT-MLC must be installed. To guarantee best performance, installing a LUT-MLC with these load types
regardless of wattage is recommended. Rarely, some load types may still flicker or glow in the off state even with the LUT-MLC installed, in which case a
different load may be required or more than one LUT-MLC is required.
3
See “Ganging and Derating” section.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
®
CasétaR Wireless Load Controls
5
369987a 5 09.09.16
Load Type and Capacity - Dimmers
Model Number Description Voltage Load Type Minimum Load
10 W with
Incandescent / Halogen
neutral (25 W
without neutral)
MLV Halogen 10 W 1000 VA 80 0 VA 600 VA
PD-10NXD
PD-3PCL
Wireless
In-Wall
Dimmer PRO
(neutral
connection
120 V~
required for
certain load
4
types)
1
Wireless
Plug-In Lamp
120 V~
Dimmer
MLV L E D See Application Note #559
CFL/LED (120 V~
3
Rated)
Hi-lumeR 1% 2-Wire
LED drivers
Dimmable Ballasts
PHPM-PA/3F and
GRX-TVI
4
5
3
1 bulb
1 driver
1 ballast 1000 VA 800 VA 60 0 VA
1 interface 3 interface 3 interface 3 interface
Incandescent / Halogen 10 W 300 W N/A N /A
CFL/LED (120 V~
3
Rated)
1 bulb
3
Incandescent / Halogen 10 W 500 W 400 W 300 W
PD-5NE
Phase
Selectable
Dimmer
(neutral
connection
required)
120 V~
CFL/LED
(120 V~ Rated)
MLV Halogen
3, 6, 7
2, 6, 7
ELV Halogen 10 W 500 W 400 W 300 W
Hi-lumeR 1% 2-Wire
LED drivers
Dimmable Ballasts
PHPM-PA/3F and
GRX-TVI
6, 7
5, 6, 7
6, 7
3
1 bulb
10 W 400 VA 400 VA 400 VA
1 driver
1 ballast 400 VA 40 0 VA 400 VA
1 interface 3 interfaces 3 interfaces 3 interfaces
ELV LED See Application Note #559
MLV L E D See Application Note #559
Incandescent / Halogen 25 W 600 W 500 W 400 W
CFL/LED
(120 V~ Rated)
3
1 bulb
3
PD-6WCL
Wireless
In-Wall
Dimmer
120 V~
Maximum Load
Not Ganged End of Gang Middle of Gang
1000 W 800 W 600 W
250 W 250 W 250 W
1000 W
(13 dr i vers)
800 W
(13 dr i vers)
600 W
(13 dr i vers)
100 W N/A N/A
250 W 250 W 250 W
400 W
(20 drivers)
400 W
(20 drivers)
400 W
(20 drivers)
150 W 150 W 150 W
1
Cannot be ganged.
2
Need to change load type to MLV. See www.casetawireless.com/change_phase
3
See bulb list at www.lutron.com/led
4
For PD-10NXD, a neutral connection is required for MLV loads, LED drivers, dimmable ballasts, and power modules (PHPM-PA, PHPM-3F, and GRX-TVI).
5
Compatible dimmable ballasts include Tu-WireR, Mark X, and PowerSenseR.
6
These loads are best operated using a forward-phase control. Consult www.lutron.com/bulblist to ensure the appropriate phase for bulb models used.
7
SSL7 compliant when in forward-phase.
PowerSense is a registered trademark of Osram Sylvania.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
®
CasétaR Wireless Load Controls
6
369987a 6 09.09.16
Ganging and Derating
When ganging with other Switches/Dimmers in the same wallbox, derating is required. See “Load Type and
Capacity” charts.
Do not remove outside fins on ends of ganged Switches/Dimmers
Each Switch/Dimmer has
inside fins removed
Do not remove outside fins on ends of ganged Switches/Dimmers
Each Switch/Dimmer has
inside fins removed
Middle of ganged Switches/Dimmers
have all fins removed
Middle of ganged Switches/Dimmers
have all fins removed
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Loading...