Lutron FCJS-010, Fcjs-eco User Manual

PowPak® Fixture Controls
Installation

Part of the Energi TriPak® Family

041507
Rev. A
09/2015

FCJS-010
0–10 V-

FCJS-ECO

®

Lutron
EcoSystem

120 – 277 V~ 50 / 60 Hz 1 A switching

6 mA sink/source

120 – 277 V~ 50 / 60 Hz 1A switching

®

14 V- 6 mA

PowPak® Wireless Fixture Control

UL 2043 Plenum Rated

Controls up to 3 ballasts or drivers (IEC 60929 Annex E.2 requires each ballast or
driver to limit the sink/source current draw to 2.0 mA maximum).

Provides IEC SELV / NECR Class 2, 12 V-, 25 mA to a PowPakR fixture sensor
(FC-SENSOR or FC-VSENSOR).

For set-up, programming, and troubleshooting with a

*

Vive

TM system, please refer to the installation instructions

included with the Vive

TM hub or at www.lutron.com

Note for Replacement:

FCJS - the "S" model can replace the non-"S" model

Important Notes:

• For installation by a qualified electrician in accordance with all local and
national electrical codes.

• Use copper conductors only.

• Check to see that the device type and rating is suitable for the application.

• DO NOT install if product has any visible damage.

• If moisture or condensation is evident, allow the product to dry completely
before installation.

• Operate between 32 °F and 104 °F (0 °C and 40 °C), ambient.

• 0% to 90% humidity, non-condensing.

• For indoor use only.

Fixture Control

Install the fixture control directly to a fixture or
on a junction box nearest to the fixture. Install

the sensor on the ceiling near the fixture to

optimize coverage in the desired area.

30 ft (9 m)

maximum

English

Wireless sensors
and controls must
be located within
60 ft (18 m) line of sight,
or 30 ft (9 m), through walls, of
the associated control module.

Default Functionality

Wireless Controls: All lights

On: 100% ; Favorite: 50%; Off: 0%

Please read before installing.

PowPak®

Sensor

Fixture
Control

Pico®
remote
control

Required Components

For each fixture, you will need:

One Fixture Control

Load
Status
LED

PowPakR Wireless Fixture Control
(FCJS-010 or FCJS-ECO)

Raise

Toggle

Lower

Start Here

Install Fixture Control and Optional Fixture Sensor

1

Suggested Installation Location: Close to the Fixture / Troffer.

WARNING! Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.

The fixture control can be installed on a fixture/troffer, junction box or marshalling box using the
conduit nut (provided) or with mounting screws (not provided). Please consult local and national
electric codes for proper installation.

A

Ideally, mount the sensor to the ceiling tile close to the fixture using the wireform or using the

adhesive strip (included). The two communication wires from the sensor attach to the fixture control
stab-in connectors. The wires are interchangeable to eliminate miswiring.

B

Once installed, energize the control module. The fixture will turn on.

Line/Hot
(Black)

Neutral

Fixture/Troffer
or Junction
Box

From back
of sensor

At least one of these transmitters (22 total allowed)

PIR Lens
Laser
Detection

+

PowPakR Fixture Sensor
(FC-SENSOR or
FC-VSENSOR)

(1 maximum)

Green/Yellow

Neutral (White)

Switched Line/Hot
(Red)

+ Violet (both FCJS-010 and FCJS-ECO)

– Gray (FCJS-010) / Violet (FCJS-ECO)

1/2 in (21 mm) Knockout Opening

Conduit Nut

Important Note: To optimize RF performance of
the product:
– Keep the lamp wiring as short as possible to

reduce the radiation from the lamp wires.

– Keep the lamp wiring as far as possible from

the PowPakR Wireless Fixture Control mounting
location.

See the Troubleshooting section for more details.

Maximize Distance

Daylight Lens

Notes:

1. Fixture control can be used
without a fixture sensor as long
as at least one Radio Powr
SavrT sensor or PicoR remote
control is used.

2. Only one fixture control can be
used per fixture sensor, and
only one fixture sensor can be
used per fixture control.

Fixture Earth

Ballast / Driver

PowPakR Fixture Control Wiring

PowPakR Fixture Control Knockout

MAINS

NEU

HOT

Class 2

+

–

Lamp Wiring

Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com

FCJS-010: At least one 0 – 10 V Fluorescent Ballast or LED Driver
FCJS-ECO: At least one Lutron® EcoSystem® Ballast or LED Driver

Consult the fixture installation guide for fixture wiring.

+

Radio Powr SavrT
Occupancy/Vacancy
Sensor

(10 maximum)

2

Associate Transmitters to Fixture Control *

Before beginning this step, make sure that there are no other fixture controls being set up in the building which are currently in association
mode. It is possible that wireless transmitters from other systems can be incorrectly associated to this module.

A

Initiate association mode on the fixture control in one of two ways:

1 Press and hold the Toggle button “ u ” for 6 seconds on the fixture control until the load attached to the fixture control starts flashing

(every 2 seconds).

2 Alternatively, shine a green laser pointer (available at hardware or office supply stores) at the laser detection hole on the sensor until the load

attached to the fixture control starts flashing (every 2 seconds).

Note: Multiple fixture controls can be placed into association mode by repeating one of the two above methods for the next fixture control prior to

moving to Step 2B.

WARNING

!

Eye injury and/or blindness hazard; avoid direct eye exposure to laser beam.

• Use of laser pointer is NOT recommended for use with Lutron® products located near reflective surfaces.

• DO NOT aim or shine laser pointers at any person, pet, vehicle, or aircraft directly, or through reflection by mirrors or other shiny surfaces. DO NOT
view the laser beam through binoculars magnifying glass, or other optical devices.

• DO NOT allow children to use laser pointers.

• Read and follow the laser pointer manufacturer’s instructions on safe use. In the event of injury, get medical attention immediately.

B

Hold the indicated button on each transmitter for 6seconds. The fixture

will flash to show that wireless transmitters have been associated.
Alternatively, for Radio Powr SavrT occupancy/vacancy and daylight
sensors, the green laser pointer can be used. See Application Note
#407 on www.lutron.com for more information. To associate another
transmitter, repeat steps 2A and 2B.

Radio Powr SavrT
Daylight Sensor

(1 maximum)

!

PicoR Remote
Control

(10 maximum)

OR

DANGER

6 mA maximum for the control lines. Switches up to 1 A total
(or maximum 3 ballasts or drivers). May be pre-installed in fixture.

Link

Test

Laser Detection

Green laser specifications:

• Wave output: constant

• Wavelength: 532 nm

• Output power:
5 mW maximum

Note: The fixture control
will automatically exit
association mode 10
minutes after the last
activity.

Fixture Controls

Auto On level: FC-SENSOR only
(not applicable for FC-VSENSOR)
Varies with ambient light level when occupancy is triggered
(e.g., 100% for a dark room, 10% for a bright room).

Timeout period: 15 minutes

For more information, see
www.lutron.com/TechnicalDocumentLibrary/369866.pdf

Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA

Notes:

1. Control wires (Violet/Gray for FCJS-010 or Violet/Violet for FCJS-ECO) can be run
as either Class1 or Class2.

2. If hanging pendant fixtures the maximum wire length between fixture sensor and
fixture control is 12ft (3.7 m). Sensor should be mounted no more than 2 ft (0.6 m)
from the fixture.

3. To install unit inside a junction box, please see Application Note 423 on
www.lutron.com

4. The fixture control needs to be accessible for some programming steps. Record
where it is mounted so that it can be easily located later.

5. When using a Radio Powr SavrT daylight sensor in conjunction with both a
PowPakR wireless fixture control and PowPakR fixture sensor, the Radio Powr
SavrT daylight sensor will provide the daylighting input to the control module, and
the PowPakR fixture sensor daylighting input will be ignored.

6. When using a Radio Powr SavrT occupancy sensor in conjunction with both a
PowPakR wireless fixture control and PowPakR fixture sensor, occupancy data
from both sensors is used; either one detecting occupancy will turn the lights
on, and the lights turn off only when both sensors have gone vacant (no longer
detect occupancy).

7. For more information on the PowPakR fixture sensor, see: Document 369866 or
048556 on www.lutron.com
For FC-SENSOR and FC-VSENSOR installation guide visit www.lutron.com