OWNER'S MANUAL
AIR CONDITIONER
REMOTE CONTROLLER ILLUSTRATION
Read this manual carefully before
installing or operating your new air
conditioning unit. Make sure to save
this manual for future reference.
The design and specifications are subject
to change without prior notice for product
improvement. Consult with the sales
agency or manufacturer for details.
www.lunariaklima.it
www.lunariaklima.it
info@lunariaklima.it
1
2
2
5
6
7
7
8
11
12
12
13
Handling the remote controller .....................
Remote controller specification.....................
Features of remote controller buttons ..........
Indicators on display panel ..........................
Auto operation...............................................
Cool/Heat/Fan operation...............................
Dry operation ................................................
Timer operation.............................................
Sleep button function...................................
Reset and lock buttons function...................
Air vertical/horizontal button function...........
Cautions.......................................................
CONTENTS
Keep the remote controller
where its signals can reach
the receiver of the indoor unit.
(A distance of 8m is allowed).
Location of the remote controller.
Handling the remote controller
1
CAUTIONS
The air conditioner will not operate if curtains, doors
or other materials block the signals from the remote
controller to the indoor unit.
Prevent any liquid from falling into the remote
controller. Do not expose the remote controller to
direct sunlight or heat.
If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly. Use curtains to prevent the
sunlight from falling on the receiver.
If other electrical appliances react to the remote
controller. either move these appliances or consult
your local dealer.
The remote controller uses two
dry batteries (R03/LR03X2)
(1) Slide the cover of the battery
compartment off according to
the arrow direction, then replace
the old batteries with new ones.
(2) Insert the new batteries
making sure that the(+) and (-)
of battery are installed correctly.
(3) Reattach the cover by sliding
it back into position.
Replacing batteries
.
8m
ADJU
ST
AUTO
COO
L
DRY
HEAT
FAN
HIGH
LOW
MOD
E
FAN
SPEED
A
IR
VERTICA
L
TIME
R ON
SLEEP
ON/O
FF
TIMER OFF
RESE
T LOCK
SET
TEM
PERATU
RE( C)
L
ED
DIS
PLAY
TURBO
AIR
HOR
IZON
TAL
NOTE: Do not use old batteries or different type
batteries or rechargeable batteries, otherwise it may
cause the remote controller malfunction.
www.lunariaklima.it
www.lunariaklima.it
2
3
ADJUST Button : Push this button to decrease the
oo
indoor temperature setting in 1 C increments to 17 C.
RESET Button: Once the recessed RESET button is
pressed, all of the current settings will be cancelled
and the controller will return to the initial settings.
NOTE: Heat mode is for reverse cycle models only.
1
6
ADJUST Button : Push this button to increase the
oo
indoor temperature setting in 1 C increments to 30 C.
2
7
MODE Button: Each time the button is pressed, the
operation mode is selected in the sequence of the
following:
3
AUTO
COOL
DRY
HEAT FAN
5
4
AIR VERTICAL Button: When press the button once
and quickly, the air flow direction setting feature of
the louver is activated. The moving angle of the
o
louver is 6 for each press. Keep pressing the button
to move the louver to the desired position. If keep
pressing the button without releasing for 2 more
seconds, the auto swing feature of the louver is
activated. The vertical louver would swing left and
right automatically. Press it again to stop.(If the indoor
unit has no this feature, there is no corresponding
operation happened when press this button.)
NOTE: If the vertical louver auto swing feature has
been set by unit control panel, press the AIR
VERTICAL button on remote controller will cancel
the feature.
Model
Rated Voltage
R51I3/BGE-M,R51I3/BGCE-M
-5 C 60 C
8m
3.0V(Dry batteries R03/LR03 2)
Remote Controller Specification
Performance Features
Features of Remote controller buttons
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling
only model without), and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range: 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
1
2
4
5
6
3
8
7
9
10
11
12
13
Environment
SET TEMPERATURE( C)
LED
DISPLAY
14
Signal Receiving
Range
TURBO
AIR
HORIZONTAL
AIR HORIZONTAL Button: When press the button
once and quickly, the air flow direction setting feature
of the louver is activated. The moving angle of the
o
louver is 6 for each press. Keep pressing the button
to move the louver to the desired position. If keep
pressing the button without releasing for 2 more
seconds, the auto swing feature of thelouver is
activated. The horizontal louver would swing up/down
automatically. Press it again to stop.
LED DISPLAY Button: Press this button to clear the
display on the indoor unit, press it again to light the
display .
~
8
ON/OFF Button: Press this button to start the indoor
unit. Press again to stop the unit.
www.lunariaklima.it
www.lunariaklima.it
TIMER OFF Button: Press this button to activate the
Auto-off time setting. Each press will increase the time
setting in 30 minutes increments, up to 10 hours, then
at 1 hour increments up to 24 hours. To cancel the
Auto-off time setting, just press the button until the
time setting is 0.0.
LOCK Button: Press this recessed button to lock all
current settings, and the remote controller will not
accept any operation except that of the LOCK. Use the
LOCK mode when you want to prevent settings from
being changed accidentally. Press the LOCK button
again to cancel the LOCK function. A lock symbol will
appear on the remote controller display when the lock
function is activated.
TURBO Button: Push this button to activate the speed
cooling function(Speed cooling operates at super high
fan speed in cooling mode). For the unit adopts PTC,
when press TURBO button in heating mode, the PTC
heater is energized and brings stronger and faster
heating operation.
Note: The unit system will automatically revert back to
the previous settings after continue operating under
powerful cooling mode for about 20 minutes.
13
14
Indicators on Display Panel
TIMER ON OFF
SET TEMPERATURE
Transmission Indicator
Temp./Timer display
Fan speed display
Mode display
ON/OFF display
This transmission indicator will light when
remote controller transmits signals to the
indoor unit.
Displays the current selected mode. Including
AUTO, COOL, DRY, HEAT (reverse cycle models
only) and FAN.
o
The temperature setting (from 17 C
o
to 30 C) or timer setting (0~24h) will
be displayed. If FAN mode is selected,
there will be no display.
This indicator will be
displayed when the unit is
operating.
Displays the selected fan speed:
AUTO, HIGH and LOW. Nothing displays
when the fan speed is selected in AUTO
speed. When AUTO or DRY Mode is
selected, there will be no signals displayed.
This display area shows the settings of the
TIMER. That is, if only the Auto-on time function
is set, it will display TIMER ON. If only the Autooff time function is set, it will display TIMER OFF.
If both functions are set, it will display TIMER
ON OFF which indicates you have chosen both
the Auto-on time and Auto-off time.
4
5
Mode display
(FAN mode)
TIMER display
11
TIMER ON Button: Press this button to activate the
Auto-on time setting. Each press will increase the time
setting in 30 minutes increments, up to 10 hours, then
at 1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until the
time setting is 0.0.
SLEEP Button: Press this button to activate the
Energy-Saving mode. Press again to stop the function.
This function is available on COOL, HEAT or AUTO
mode only and maintain the most comfortable
temperature for you.
12
10
NOTE: While the unit is running under SLEEP mode,
it would be cancelled if press the MODE,FAN SPEED
or ON/OFF button.
FAN SPEED Button: Press the button to select the
Fan speed in the sequence: AUTO, LOW and HIGH.
Each time the button is pressed, the fan speed
selection is shifted.
9
LOCK display is displayed when pushing the
LOCK button. Push the LOCK button to clear
display.
LOCK Indicator
www.lunariaklima.it
www.lunariaklima.it
AUTO operation
Ensure the unit is plugged in and
power is available. The OPERATION
indicator on the display window of the
indoor unit illuminates.
1. Mode select button (MODE)
Press to select AUTO.
2. Temperature button ( )
Set the desired temperature. Normally,
oo
set it between 21 C and 28 C.
3. ON/OFF button
Press the ON/OFF button to start
the air conditioner.
ADJUST
ON/OFF button
Push this button again to stop the air
conditioner.
If the AUTO mode is uncomfortable,
you can select the desired conditions
manually. When you select the AUTO
mode, you do not have to set the fan
speed. The fan speed will be
automatically controlled.
When you set the air conditioner in
AUTO mode, it will automatically
select cooling, heating (Reverse cycle
models only), or fan operation
depending on what temperature you
have selected and the room
temperature.
Once you select the operating mode,
the operating conditions are saved in
the unit's microcomputer memory.
Thereafter, the air conditioner will start
operating under the same conditions
when you simply push the ON/OFF
button of the remote controller.
Start
Stop
2
1
3
DRY OPERATION
Ensure unit is plugged and power is
available.
1. Mode select button (MODE)
Press to select COOL, HEAT (Reverse
cycle models only), or FAN mode.
2. Temperature button ( )
Set the desired temperature, the
most comfortable temperature is
oo
between 21 C and 28 C.
3. Fan speed button (FAN SPEED)
Press to select "AUTO", "LOW"
and "HIGH".
ADJUST
ON/OFF button
Push this button again to stop the air conditioner.
Ensure unit is plugged and power is
available. The OPERATION indicator
on the display panel of the indoor unit
starts flashing.
1. Mode select button (MODE)
Press to select DRY.
2. Temperature button ( )
Push the " " button to set
the desired temperature.
3. ON/OFF button
Press the ON/OFF button to start
the air conditioner. No fan speed
indicator displays. The Indoor fan
speed will be automatically
selected LOW.
ADJUST
ADJUST
Start
Stop
Start
COOL/HEAT/FAN operation
NOTES: The temperature cannot be controlled under
FAN only mode. While in this mode, only steps 1, 3 and
4 may be performed.
6
7
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
2
1
4
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
2
1
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
4. ON/OFF button
Press the ON/OFF button to start the air conditioner.
The OPERATION indicator on the display panel of the
indoor unit illuminates. The operating mode is selected
in accordance with the room temperature and
operation starts after approximately 3 minutes (If you
select FAN mode, the unit will start immediately).
www.lunariaklima.it
www.lunariaklima.it
Timer operation
To press the TIMER ON button can set the auto-on time
of the unit. To press the TIMER OFF button can set the
auto-off time of the unit.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last
Auto-on setting time and the signal "h"
will be shown on the LCD display area.
Now it is ready to reset the Auto-on time
to START the operation.
2. Push the TIMER ON button again to set
desired Auto-on time. Each time you
press the button, the time increases by
half an hour between 0 and 10 hours and
by one hour between 10 and 24 hours.
To set the Auto-on time.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last
Auto-off setting time and the signal "h"
will be shown on the LCD display area.
Now it is ready to reset the Auto-off time
to START the operation.
2. Push the TIMER OFF button again to set
desired Auto-off time. Each time you
press the button, the time increases by
half an hour between 0 and 10 hours and
by one hour between 10 and 24 hours.
The effective operation time set by
the remote controller for the timer function is limited to
the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0,
9.5, 10, 11, 12, 13,14, 15,16,17, 18, 19, 20, 21, 22, 23
and 24.
0.0,
CAUTION
!
Example of timer setting
TIMER ON
Start
Off
6 hours later
(Auto-on Operation)
The TIMER ON feature is
useful when you want the unit
to turn on automatically before
say when you return home.
The air conditioner will
automatically start operating
at the set time.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of
starting operation time and the signal "h" will show on
the display area.
2. Press the TIMER ON button to display "6.0h" on the
TIMER ON display of the remote controller.
3. After setting the TIMER there will be a one-half second
delay before the remote controller transmits the signal
to the Air Conditioner. Then, after approximately
another 4 seconds, the set temperature will re-appear
on the digital display.
TIMER ON
Example:
h
Set
ON/OFF button
Push this button again to stop the air conditioner.
Stop
Note: The fan speed cannot be adjusted when the unit
is in AUTO and DRY mode.
8
9
1
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
1
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
3. After setting the TIMER ON, there will be a one-half
second delay before the remote controller transmits the
signal to the air conditioner. Then, after approximately
another 4 seconds, the signal "h" will disappear and the
set temperature will re-appear on the LCD display window.
the signal to the air conditioner. Then, after
approximately another 4 seconds, the signal "h" will
disappear and the set temperature will re-appear on
the LCD display window.
3. After setting the TIMER OFF ,there will be a one-half
second delay before the remote controller transmits
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when
you want the unit to turn off automatically
after you go to bed. The air conditioner
will stop automatically at the set time.
TIMER OFF
h
www.lunariaklima.it
www.lunariaklima.it
11
10
Stop
On
Set 10 hours later
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the
last setting of stopping operation
time and the signal "h" will show on
the display area.
2. Press the TIMER OFF button to
display "10h" on the TIMER OFF
display of the remote controller.
3. After setting the TIMER there will
be a one-half second delay before
the remote controller transmits the
signal to the Air Conditioner. Then,
after approximately another 4
seconds, the set temperature will
re-appear on the digital display.
Example:
TIMER ON OFF
h
On
Stop
2 hours later
after setting
Set
To stop the air conditioner 2 hours after setting and start
it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h on
the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h on
the TIMER ON display .
5. Wait for 4 seconds and the remote control will display
the setting temperature again.
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want
to stop the air conditioner after you
go to bed, and start it again in the
morning when you wake up or when
you return home.
Example:
COMBINED TIMER
(Setting both ON and OFF timers
simultaneously)
Start
Example:
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you
want to start the air conditioner
before you wake up and stop it
after you leave the house.
To start the air conditioner 2 hours
after setting, and stop it 5 hours
after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button
again to display 2.0h on the
TIMER ON display.
3. Press the TIMER OFF button.
Off
Stop
Start
10 hours later
after setting
TIMER ON OFF
h
2 hours later
after setting
5 hours later
after setting
Set
The timer setting(TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be
activated first.
CAUTION
!
Sleep button function
1
When you press the SLEEP button, the
economic running function will be
activated. During Cooling, Heating or
AUTO operation, the set temperature of
the air conditioner will automatically
o
increase or decrease 1 C per hour for 2
hours. After 2 hours, the set point will
continue at that temperature and the fan
motor will be set to LOW speed. The
sleep mode function can maintain the
most comfortable temperature and save
more energy for you.
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
NOTE: The SLEEP function is only available under
Cooling, Heating and AUTO operation.
4. Press the TIMER OFF button again to display 5.0h
on the TIMER OFF display .
5. Wait for 4 seconds and the remote control will
display the setting temperature again.
www.lunariaklima.it
www.lunariaklima.it
Reset and Lock buttons function
1
1. When you press the recessed LOCK
button, all current settings are locked in
and remote controller does not accept
any operation except that of the LOCK.
Use the LOCK mode when you want to
pre-vent settings from being changed
accidentally.
Press the LOCK button again when
you want to cancel the LOCK mode.
A lock symbol will appear on the
bottom right hand side of the remote
controller display when the LOCK
function is activated.
2. When you press the recessed RESET
button, all current settings are
cancelled and return to original factory
settings.
2
Air vertical/horizontal button function
Use the AIR HORIZONTAL/VERTICAL
button to adjust the airflow direction(up/
down, left/right).
1. When press the button once and
quickly, the air flow direction setting
feature of the louver is activated. The
o
moving angle of the louver is 6 for
each press. Keep pressing the button
to move the louver to the desired
position.
2. If press the button without releasing
for 2 more seconds, the auto swing
feature of the louver is activated. The
horizontal/vertical louver would swing
(up/down or left/right)automatically.
Press it again to stop.
1
12
13
Cautions
1. When replacing batteries, do not use old batteries or
different type batteries. Otherwise it may cause the
remote controller to malfunction.
2. If you do not use the remote controller for a few
weeks or more, remove the batteries. Otherwise,
battery leakage may damage the remote controller.
3. Do not dispose batteries as unsorted municipal waste.
Collection of such waste separately for special
treatment is necessary.
4. The average battery life during normal use is
approximately half a year. Replace the batteries when
there is no receiving beep from the indoor unit or if
the transmission indicator on the remote controller
fails to light.
5. Be sure there are no barriers between the remote
controller and the receiver of indoor unit otherwise
the air conditioner will not work.
6. Keep the Remote Controller away from all liquids.
7. Protect the Remote Controller from high temperatures
and exposure to radiation.
8. Keep the indoor receiver out of direct sunlight or the
Air Conditioner may malfunction.
9. Keep controller away from EMI (Electro-Magnetic
Interference) supplied by other household appliances.
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
LOW
MODE
FAN SPEED
AIR
VERTICAL
TIMER ON
SLEEP
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
LED
DISPLAY
TURBO
AIR
HORIZONTAL
NOTE: When the louver swing or move to a position
which would affect the cooling and heating effect of the
air conditioner, it would automatically change the swing/
moving direction.
www.lunariaklima.it
www.lunariaklima.it
Loading...