Lumi United Technology AK022 User Manual

Smart Wall Switch (No Neutral, Double Rocker)

Smart Wall Switch (No Neutral, Double Rocker)

Product Profile

Push Button

Short Press Once: Turn on/off
Long Press for 5s: Reconnect
Quick Press 3 Times: Effective Range Test

Indicator Light

*

This product requires a compatible hub. Some features require a specific hub.
For the detailed list, please visit: www.aqara.com/support

Warning

A certain amount of electrical knowledge is required to install a smart

1.
wall switch. For your safety, we recommend that you ask a qualified
electrician to help you install it;

This product is for indoor use only; do not use it in humid environment;2.

Do not install this product near a heat source.3.

Before you install

This product is only used to replace a single pole switches rather than a
3-way switch.

Installation

Visit www.aqara.com/support for more information.

Turn off power at circuit breaker or fuse box and test that power is off

1.
before wiring. (Please switch the light several times to make sure that
the power has been disconnected)

ONOFF

ONOFF

ONOFF

OFF

OFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

Remove the existing switch and identify the wires with wire labels.2.

Ground
Usually green.

Neutral
Required, but not always present,
usually white.

Line(Hot)/Load
Required, usually black, and always
present.

Install the smart wall switch and connect wires as required.3.

Ground
Usually green.

Neutral
Required, but not always present,
usually white.

Line(Hot)/Load
Required, and always present.

Tuck the wires into the wall box leaving room for the smart switch. Using

4.
the screws provided, mount the smart switch to the wall box. Be careful
not to crush any wires. (Note: avoid overtightening the screws.)

Install the wall plate, turn main power ON at the circuit breaker, and test

5.
the switch by pressing the button;
If it doesn’t work, please check: a. If the wiring is correct; b. If the power
is restored.
If it works, add the switch to the app following the next steps;

Quick Setup

Please add the Hub to the app according to the Hub Quick Start Guide.

1.

2.

Please open the app, and then tap “+” in the top right corner to enter
“Add Device (Accessory)” page. Select “Smart Wall Switch (No
Neutral, Double Rocker)”, and add it according to instructions.

*If the connection fails, please move the hub closer to the switch, connect to
power and try again.

Effective Range Test: Quick press the button on the device 3 times. If the
Hub makes voice prompts, it indicates that the device can communicate
effectively with the Hub.

Indicator Light Description

Indicator Light Status Status Description

Blue light blinks quickly Zigbee network is connecting

Blue light keeps on Zigbee network works properly

Red light blinks quickly High temperature alarm

Red light blinks slowly Zigbee network is not connected

Specification

Model: QBKG14LM
Dimensions: 120 x 74 x 36.5 mm (4.72 x 2.91 x 1.44 in)
Wireless Protocol: Zigbee3.0
Input: 120 V AC 60Hz
Min Load: 3 W/way (Incandescent), 5 W/way (CFL/LED), typical load
Max Load: 600 W/way (Incandescent), 200W/way (CFL/LED), 1/4 HP
Operating Temperature: 0 – 40°C（32 – 104°F）
Operating Humidity: 0 – 95% RH, non-condensing

Manufacturer: Lumi United Technology Co., Ltd.
Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian
Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Online Customer Service: www.aqara.com/support
Email: [e-mail]

Switch de pared inteligente (sin neutro, basculante doble)

Perfil del producto

Botón

Pulsación corta: encender/apagar

Pulsación larga durante cinco
segundos: volver a conectar

Tres pulsaciones rápidas:
prueba de alcance efectivo

Luz indicadora

*

Este producto debe utilizarse con un dispositivo con funcionalidad de puerta de
enlace. Algunas funciones requieren compatibilidad con modelos de puerta de
enlace específicos. Para una lista detallada, visite: www.aqara.com/support

Advertencia

La instalación de un switch inteligente requiere ciertos conocimientos

1.
en materia de electricidad. Para su seguridad personal, se recomienda
pedir ayuda a un electricista cualificado para la instalación.

Este producto ha sido diseñado exclusivamente para uso en interiores;

2.
no lo utilice en un entorno húmedo.

No instale el producto cerca de una fuente de calor.3.

Antes de la instalación

Verifique la compatibilidad

Este producto solo puede sustituir switches de control sencillo en lugar de
switches de doble control.

Installation

Visitar en www.aqara.com/support para obtener más información.

Desconecte la alimentación del switch que se vaya a sustituir antes de

1.
la instalación (apague y encienda la luz varias veces para comprobar
que se ha desconectado la alimentación).

ONOFF

ONOFF

ONOFF

OFF

OFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

Retire el switch que se vaya a sustituir y marque el cable con la etiqueta

2.
de cables para identificar el cable correspondiente en la instalación.

Tierra
normalmente de color verde.

Neutro
Obligatorio, pero no siempre presente.

Línea/Carga
Obligatorio, normalmente de color negro,
siempre presente.

Instale el switch de pared inteligente y conecte el cable según sea

3.
necesario;

Tierra
normalmente de color verde.

Neutro
Obligatorio, pero no siempre
presente.

Línea/Carga
Obligatorio, siempre presente.

Extraiga la cubierta de superficie y fije el switch a la caja de

4.
interruptores con tornillos. (Nota: no apriete demasiado los tornillos
para no deformar el switch)

Coloque la cubierta de superficie del switch, conecte la alimentación y

5.
controle con el botón; si el control no funciona, compruebe que las
conexiones sean correctas y que se haya conectado la alimentación; si
funciona, siga los pasos a continuación para agregar el producto.

Configuración rápida

Agregue el hub a la aplicación de acuerdo con la Guía rápida del hub.

1.

2.

Abra la aplicación, pulse «+» en la parte superior derecha para acceder
a la página «Add Device (Accessory)» (Agregar dispositivo
[accesorio]). Seleccione Switch de pared inteligente (sin neutro,
basculante doble) y siga las instrucciones para agregarlo.

*Si falla la conexión, acerque el switch de pared al hub, conéctelo y vuelva a
intentarlo.

Prueba de alcance efectivo: pulse rápidamente tres veces el botón en el
accesorio. Si el hub emite un mensaje de voz, significa que el accesorio
y el sensor se están comunicando correctamente.

Descripción de la luz indicadora

Estado de la luz indicadora Descripción del estado

La luz azul parpadea rápidamente

Luz azul fija La red Zigbee funciona correctamente

La luz roja parpadea rápidamente Alarma de alta temperatura

La luz roja parpadea lentamente No hay conexión con la red Zigbee

Se está estableciendo conexión con la
red Zigbee

Especificaciones

Modelo: QBKG14LM
Dimensiones: 120 x 74 x 36,5 mm（4,72 x 2,91 x 1,44 pulgadas)
Protocolo inalámbrico: Zigbee3.0
Entrada: 120 VCA, 60 Hz
Cargas mínimas: 3W/vía (incandescente), 5W/vía (CFL/LED), carga típica
Cargas máximas: 600W/vía (incandescente), 200W/vía (CFL/LED),

Temperatura de funcionamiento: 0 – 40°C（32 – 104°F）
Humedad de funcionamiento: 0 – 95% HR, sin condensación

1/4HP (total)

Fabricante: Lumi United Technology Co., Ltd.
Dirección: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian
Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Servicio de atención al cliente en línea: www.aqara.com/support
Correo electrónico: [e-mail]

FCC ID: 2AKIT-AK022

Federal Communications Commission (FCC) compliance statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

IC: 22635-AK022

IC NOTICE TO CANADIAN USERS

This device complies with Industry Canada license‐exempt RSS standard(s). Operation
is subject to the following two conditions: (1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device. This device complies with RSS‐247 of Industry
Canada. Operation is subject to the condition that this device does not cause harmful
interference. This Class B digital apparatus complies with Canadian ICES‐003 (Cet
appareil numérique de la Classe B conforme à la norme NMB‐003 du Canada).

This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of
20 cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.

Cet équipement est conforme aux limites IC d'exposition aux radiations définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance
minimale de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être situé ou
opérant en conjonction avec une autre antenne ou émetteur.