HD Camera
TIX301 Interchangeable Flush Fit Thru-Hull HD Camera
Installation and Operation Guide
Rev 3 45-0039
FEATURES
PACKING LIST
TABLE OF CONTENTS
Number
Section
Page
1.0
BEFORE YOU START
3
2.0
TIX301 INTERCHANGEABLE FLUSH FIT THRU-HULL HD CAMERAS
4
2.1
Materials and Dimensions
4
3.0
THRU-HULL HD CAMERA ASSEMBLY INSTALLATION
5
4.0
REMOVING THE HD CAMERA INSERT MODULE
6
5.0
ELECTRICAL CONNECTIONS
6
5.1
Fuse Installation
6
5.2
Cable Size (gauge)
6
5.3
HD-SDi Output Connection
7
5.4
SD (Composite) Output Connection
8
5.5
Camera Set up
9
6.0
MAINTENANCE
10
7.0
PRODUCT SUPPORT INQUIRIES
10
8.0
SPECIFICATIONS
11
9.0
WARRANTY
11
Congratulations! You have purchased a LUMISHORE advanced technology HD Camera. Every care has been taken to
ensure your Thru-Hull HD Camera arrives in perfect condition, so please enjoy the ultimate experience in underwater
viewing.
LUMISHORE Thru-Hull Interchangeable products are designed for those owners who prefer the integrity of a thru-hull
installation where the product may be removed from the inside of the hull. The LUMISHORE Interchangeable Thru-Hull
range is suitable for many sizes and types of watercraft, including Sports Boats, Cruisers, Yachts, and Super Yachts.
LUMISHORE TIX301 Interchangeable Thru-Hull HD Cameras have an integrated internal module to make installation
simple and ensure trouble free operation for years to come.
Please read the following pages before attempting installation to ensure complete understanding of the
LUMISHORE HD Camera.
● Interchangeable (removable HD Camera module) Flush Fit Thru-Hull camera for transom, bottom, and hull-side
mounting
● Requires 2" (51mm) entry hole (When using isolation sleeves refer to manual for correct hole size)
● Latest HD Camera technology
● HD-SDI Video Output and Composite Video Output
● Toughened BK7 Borosilicate lens
● Marine-grade bronze housing
● 12 Volt only
If any of the following items are missing, email or call LUMISHORE using the information provided in Product Support
Section. TIX301 Thru-Hull housing, HD Camera Module, Locknut and Rubber Washer, Installation and Operation Guide.
Page 2
1.0 BEFORE YOU START
Note: Before mounting the camera, record the serial number for future reference. The number is located on the
back of the camera.
● HD Camera - DO NOT touch camera glass. Take care to keep the camera glass clean during handling
and installation.
● Always ensure that the vessel’s power source and battery are disconnected or isolated prior to installation.
● A qualified professional should carry out both electrical and mechanical installation. If in doubt please contact
LUMISHORE. Refer to Product Support Section.
● Always use a suitable fuse or circuit breaker to protect the complete system. Each camera should be
individually fused using the fuse holder supplied with the camera. Make sure to choose the correct fuse size
for the 12 Volt supply.
● The Thru-Hull maybe installed into GRP (Glass Reinforced Plastic or Fiberglas) and wooden hulls.
● The camera should be installed 6”-10” (150-250mm) below the surface of the water although this is not
critical.
● Never try to install or remove the thru-hull fitting or the Camera Insert Module with the vessel in the water.
● Confirm there is clearance (more than 7”) inside the hull to be able to remove the Camera Insert Module.
● The camera should not be exposed to any temperatures in excess of 150°F (65°C). For example, next to hot
engine components or where exhaust emissions could be expelled onto the camera while underway.
● Do not over tighten the retaining nut.
● All LUMISHORE Thurs Hull products should have bonding to the DC system via bonding strap for galvanic
protection.
● Caution: NEVER leave the vessel unattended in water if the Camera Insert Module is not in place
Page 3
2.0 TIX301 INTERCHANGEABLE FLUSH FIT THRU-HULL CAMERAS
2.1 Materials and Dimensions:
Cable: 9'9" (3 meters)
Camera Alignment
indicator
O Ring Seal
HD Camera
Front Glass
Camera Module
Housing
Rubber
Washer
Locknut
Cathodic
Protection Point
Bonding Attention:
Failure to bond the cameras properly and maintain the appropriate protection will invalidate the LUMISHORE warranty.
LUIMISHORE cameras should be connected to the vessel’s DC Bonding system to ensure protection from electrolytic /
galvanic corrosion. All bonding connections should be fully checked prior to returning the vessel to the water.
LUMISHORE cameras have integrated circuitry to protect cameras from external issues, but these are dependent upon
correct bonding.
Installation Considerations
● Location – positioning will be dependent on both external and internal obstacles; consideration should also be
given to installation wiring and internal access within the vessel. Ideally the camera modules should be
installed 6” to 10” (150-250mm) below the surface water line.
● Select a flat surface; make sure that both the internal and external surfaces of the hull are even and parallel.
It may be necessary to sand or grind the surface.
● A hole will be drilled to allow the Thru-Hull Camera Assembly to be inserted; care must be taken to ensure
there is unrestricted access inside the hull.
● Confirm there is clearance (more than 7”) inside the hull to be able to remove the Camera Insert Module.
● The camera is temperature sensitive and must not be located close to the exhaust.
Page 4
3.0 THRU-HULL CAMERA ASSEMBLY INSTALLATION
Top Centre
Back of camera
1. Measure the position of the cameras, mark carefully, and double-check for internal obstacles.
2. Confirm there is clearance (more than 7”) inside the hull to be able to remove the Camera Insert Module.
3. Drill a 2 inch (51 mm), perpendicular hole through the hull.
Note: The required hole size will change when using an isolation sleeve, refer to the isolation sleeve instructions,
supplied with the sleeves, for further information.
4. The exposed inner hull surface must be properly sealed to prevent water intrusion into the hull before the Thru-Hull
is secured in place.
5. Before inserting the Thru-Hull Camera Assembly ensure that the hull surface is free from dirt and grease and
remove any existing anti-foul from the hull surface.
Note: Do not use an alcohol-based solvent as this may have an adverse effect on the sealant.
TO ALIGN THE PICTURE - MAKE SURE THE "TDC" ON THE BACK OF THE CAMERA MODULE IS AT THE
TOP CENTRE OF THE THRU-HULL CAMERA ASSEMBLY WHEN IT IS INSERTED.
5. Using an approved adhesive (3M 4200 Marine or similar), apply liberally a continuous bead of sealant around the
entire circumference of the sealant groove, on the base of the stem, and on the shaft of the thru-hull.
6. Gently insert the stem of the Thru-Hull Camera Assembly through the hole in the hull.
7. Apply gentle even pressure with a slight circular motion until the Thru-Hull housing is flush with the hull surface.
8. From inside the vessel, feed the supplied rubber washer down the shaft of the Thru-Hull fitting. Screw the locking
nut in place and tighten hand tight. Do not tighten fully at this stage, excess pressure will push all of the
sealant out.
9. Remove excess sealant that is squeezed from behind the camera with a rag.
10. Allow the sealant to cure according to the sealant manufacturer’s instructions. Once fully cured, tighten the locking
nut. Hand tight only - excessive force can cause damage to the camera module or to the hull of the vessel.
11. Attach the vessel’s bonding protection to the bonding bolt on the rear of the locking nut.
!! IMPORTANT:
● Ensure that each camera module has correct vertical and horizontal alignment with the hull. Ensure the
"TDC" on the rear of the camera is at the top centre.
● Before launching the vessel the sealant should be checked to ensure it is fully cured in accordance with
the manufacturer’s instructions.
Page 5
4.0 REMOVING THE HD CAMERA INSERT MODULE
5.0 ELECTRICAL CONNECTIONS
!! IMPORTANT:
Care must be taken to ensure the lens is not damaged before removing the camera module. If the lens on the
Thru-Hull has been damaged and the Camera Insert Module is removed, water will enter the vessel.
The interchangeable module should only be removed after consultation with Lumishore and only in the event of camera
failure or module upgrade.
● Replacement is easily performed. However, full instructions are available from Lumishore to ensure that this is
done in a way that optimises the life of the unit.
● Unauthorised removal of the insert will result in the warranty being void.
5.1 Fuse Installation
Each camera should be individually fused, the TIX301 HD camera module is supplied with an external fuse holder and
two fuses. The correct fuse for 12 Volts is a 1 A fuse
5.2 Cable size (Gauge)
LUMISHORE cameras have advanced electronic systems that protect them from under current or voltage.
Note: Current draw per module with a camera connected: 12VDC – 0.25 A
● Proper wire cable size must be considered when installing the cameras.
● Compute the gauge of the cable needed camera at 12VDC
● Cable lengths referenced in the Conductor Size tables are from the source to the cameras and back to the
source.
Calculate the total current draw of all products that are connected to the terminal strip and use the chart below to find
cable size from power source to terminal strip. Use the same size wire from the terminal strip to each camera.
Page 6
HD-SDI
Connector
Joystick for On
Screen Display
Composite
(CVBS)
Connector
12V DC Power
Connector
5.3 HD-SDi Output Connection
● If required an AC / DC PSU can be supplied
● The Joystick can be used to set up the camera using the On Screen Display – see section 5.5
● If the display has a direct HD-SDi input then there is no need for a HD-SDi to HDMI Converter
● The connections should be fitted inside a waterproof junction box to protect them from contact from water
Page 7
Fuse
DC Input
(2.1 mm Power Jack)
Composite Output
(BNC Connector)
SD Display
TIX 301 HD
Camera
HD-SDI
Connector
Joystick for On
Screen Display
Composite
(CVBS)
Connector
12V DC Power
Connector
5.4 SD (Composite) Output Connections
● The Joystick can be used to set up the camera using the On Screen Display – see section 5.5
● NTSC / PAL mode should be selected using the on screen display
● The connections should be fitted inside a waterproof junction box to protect them from contact from water
Page 8
5.5 Camera Operation and Connections
The camera has several modes of operation. These can be selected using the joystick button located in the cable just
before it enters into the back of the light / camera module, the menu is shown on the display screen. The table below
shows the layout of the On Screen Display:
Page 9
6.0 MAINTENANCE
7.0 PRODUCT SUPPORT ENQUIRIES
● The locking nut should be inspected on a regular basis to ensure they are kept tight. LUMISHORE recommends
general inspection of the camera module and cable attachments every month.
● The glass lens should be kept clean with a plastic scraper or soft brush. Do not use an abrasive cloth or cleaning
agent as permanent damage to the lens may occur.
● To prolong device lifetime and prevent marine growth build up, a good quality antifouling system must be used to
coat the external body of the device. This should be renewed regularly.
If you have questions or comments, please email info@lumishore.com or call:
USA (941) 405-3302, United Kingdom +44(0)208 144 1694, France +33(0)493 582 537.
Page 10
8.0 SPECIFICATIONS
Camera Type:
1080p Full HD Camera
Camera Features:
Full HD Mega Pixel (1080P) Camera
Wide Dynamic Range (WDR)
3D Digital Noise Reduction (3D-DNR)
Automatic Low light mode
Camera Outputs:
HD-SDi
SD Composite CVBS (NTSC / PAL Selectable)
Housing Type:
Aluminium Bronze with Interchangeable Insert
Voltage Input:
12V (9V to 15V) DC
Voltage Input Connector:
2.1 mm DC Power Jack
Video Output Connector:
BNC connector
Light Face Diameter:
73mm / 2.9 in
Profile (Height) of Housing
5.1mm / 0.2 in
Hole Cut-Out for Shaft and Cable:
51mm / 2 in (When using isolation sleeves refer to manual for correct hole size)
Shaft Length:
125mm / 4.9 in
Camera Power Consumption
Up to 2W
Camera Cable Length:
1m / 3 ft 3 in
9.0 WARRANTY
LUMISHORE Ltd warrants the Thru-Hull Camera System to be free from defects in workmanship and materials for a
period of two years, starting from the date of original purchase. Should your camera system have a problem during this
period, please contact your dealer as soon as you become aware of the defect.
Misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and
camera, installation by unqualified personnel, unauthorized repair or modification will void this warranty. For the avoidance
of confusion and doubt, non-compliance with all installation, maintenance, and operating instructions in this document
constitute non-conformance with warranty terms.
Page 11
NOTES
Page 12
Scan with your smart phone to link to
TIX-301 HD CAMERA
Lumishore
Home page
Lumishore USA
(Americas Enquiries)
7137 24th Court East
Sarasota, FL 34243
www.lumishore.com
info@lumishore.com
Lumishore Ltd
Head Office
Unit 11, Technium 1
King's Road
Swansea SA1 8PH
United Kingdom
THANK YOU
FOR PURCHASING LUMISHORE CAMERAS!
Page 13
Loading...