lumishore Lumi-Link Setup And User Manual

Lumi-Link Command Center - Setup and User Guide

Exmple 1; Single Zone –

Example 2; Multizone – UW lights, Starboard,

Example 3; Multizone – UW lights &

lights and courtesy lights.

First Time use…

When first installed the system needs to be setup. Setup is a quick and easy process and is only performed upon
initial installation or after a firmware upgrade.

Setup discovers lights that are attached to the network and allows the user to select between a Single Zone or
Multizone mode display.

Underwater lights can be setup as a “Single zone” or as a “Multizone”

For Underwater and Above water installations choose Multizone Mode as per the following examples….

Configuration examples…

UW lights Only

Port, Transom.

Lumishore LUX – E.g. downlights, strip

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

45-0138 - Rev 1

www.Lumishore .com

1

www.Lumishore .com

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

The position of the lights around the vessel can also be setup. This ensures

Select “Setup” Icon

Select “Preferences”

Select “System Setup”

Selecet “Light Discovery”

The system discovers ALL lights

attached

Check that all lights have been found

that sweep mode works in the correct order. (Above water zones do not
require position information but can be set if desired).

Light Discovery Process…

Upon first installation and before choosing single vs multizone, the lights connected to the Lumi-link network need
to be discovered.

Perform these steps on first use or if new lights have been added or deleted from the Lumi-link network.

Note – if the number of lights found does not match the expected number, check connections and that each light has

power.

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

2

Single mode setup…(Skip if setting up as Multizone)

“Wink Light” to identify it on the vessel – the

light will flash RGB

Use the diagram above as a guide, edit the

light position relative to the vessel.

Repeat for all Lights and then press Save

Select Setup as “Single Zone”

The next step allows the position of the underwater lights to be set around
the vessel. This ensures the lights are sent information in the correct order
and color change in the correct sequence.

To set the positions use the following steps and the example positions
shown below.

Light Set up is now complete! The lights can be controlled from the Lumi-link control panel.

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

3

www.Lumishore .com

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

Lumi-link Control Panel…

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

4

Multi-Zone Setup and Create new Zone…

Select Setup Icon

Select Create Zone

Rename the zone and choose a suitable icon

Use the Name of the light or “wink Light” to identify

allocate to the Zone and then Save the selection.

(Optional) – Light positions can be assigned. This

sequence. Eg for Underwater lights.

The Lights in this zone will appear, change their

The new zone will appear on the Zone homescreen.

Press the power icon to turn each Zone on/off, Press

the RHS of tab to enter Main control page.

Main control page….

Select “Setup as Multi Zone”

Lighting zones can be created for different areas of the vessel. A zone could contain
underwater lights, strip lights, downlights, courtesy lights or a mixture of the above.
The zone names can be edited and an icon selected for easy identification.

each light on the network. Select which lights to

NOTE: A light can exist in 1 zone only, it cannot be placed in mutiple zones.

ensures the sweep mode will work in the correct

position as required and then press save.

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

5

To Edit or delete a Zone…

To Edit or Delete this zone long Press (>3sec) the

Zone tab.

Rename, change icon, re-assign lights, Save,

Cancel or Delete zone.

Create the 5 separate lighting zones and select

the desired color & intensity for each one.

Select “Save as Scene” from the Setup menu

Rename the scene and select an icon. Ensure

the zones to be included are checked.

Hold for >3 Sec

www.Lumishore .com

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

Creating lighting Scenes…

Once each zone has been setup the user can select the colour, effect and intensity for each of these lighting zones.
These preferences can then be saved as a lighting “Scene”.

Scenes can include a single zone or mutiple zones, they can also include a zone “set to off”.

More than one scene can be active at a time, if zones are shared between scenes, the Zones will follow the last
Scene command.

In the example below each of the 5 zones has been allocated a different colour and Zone 5 is set to Off. To create
this as a new scene e.g. “Docking Mode” follow the steps below….

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

6

To Edit or delete a Zone…

To Edit or Delete this zone long Press (>3sec) the

Zone tab.

Rename, change icon, re-assign lights, Save,

Cancel or Delete zone.

Create the 5 separate lighting zones and select

the desired color & intensity for each one.

Select “Save as Scene” from the Setup menu

Rename the scene and select an icon. Ensure

the zones to be included are checked.

Hold for >3 Sec

Note: When a zone is created, edited or deleted all zones default to green at 25% intenisty. This indicates that any

changes have been successful.

Creating lighting Scenes…

Once each zone has been setup the user can select the colour, effect and intensity for each of these lighting zones.

These preferences can then be saved as a lighting “Scene”.

Scenes can include a single zone or mutiple zones, they can also include a zone “set to off”.

More than one scene can be active at a time, if zones are shared between scenes, the Zones will follow the last

Scene command.

In the example below each of the 5 zones has been allocated a different colour and Zone 5 is set to Off. To create

this as a new scene e.g. “Docking Mode” follow the steps below….

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

7

Select Setup Icon

Select preferences

Select Lock/Unlock

Enter the Default Password: 0000

To change the password select “Set

When locked, Setup, create zone & create

the system.

www.Lumishore .com

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

Control from Smart Device or Web browser…

Ensure your smart device is connected the same network as the Lumi-link Command centre. Depending on
instalation this may be the vessels onboard WIFI, the MFD WIFI or the Lumishore Lumi-Link Display WIFI. The
following example shows the Lumi-link Command center connected to the MFD wifi….

Ensure the MFD wifi is switched on and the smart device is connected to it.

Using the MFD – launch the Lumi-link app

Select Setup Icon

Select preferences

Select About Screen

Make a note of the IP address

Note: it may be different to the example

below

Type the IP address into the browser on the

smart device

You can now control the lights remotley

using the Lumi-Link app.

Note - from time to time the MFD or network router may change the IP address automatically. If the Lumi-link app
does not display ensure you are connected to the correct wifi network and that you have entered the correct IP
address.

Password Protect (Optional)…

Once setup, Zones and Scenes have been created, they can be password protected to prevent accidental editing or
deletion. The default password is “0000” This can be changed within the same menu.

Password”.

To Lock the system select “Lock”

Scenes and long press edits are greyed out &
non functional. Repeat the process to Unlock

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

8

Control from Smart Device or Web browser…

Select Setup Icon

Select preferences

Select About Screen

Make a note of the IP address

below

Type the IP address into the browser on the

You can now control the lights remotley

Ensure your smart device is connected the same network as the Lumi-link Command centre. Depending on
instalation this may be the vessels onboard WIFI, the MFD WIFI or the Lumishore Lumi-Link Display WIFI. The
following example shows the Lumi-link Command center connected to the MFD wifi….

Ensure the MFD wifi is switched on and the smart device is connected to it.

Using the MFD – launch the Lumi-link app

Note: it may be different to the example

smart device

using the Lumi-Link app.

Note - from time to time the MFD or network router may change the IP address automatically. If the Lumi-link app
does not display ensure you are connected to the correct wifi network and that you have entered the correct IP
address.

Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | [phone] | Sales @LumishoreUSA.com

www.Lumishore .com

9