How it Works
luminii
Loading...
BOS S

luminii BOS C, BOS S Installation Instructions Manual

Download
Installation Instructions for Bosca
Models BOS-XX-C-XX, & BOS-XX-S-XX
E472444
Page 1 of 6
Bosca clip-in mount or Bosca magnetic
Bosca screw-in mount
Bosca adjustable hinge mounting
Instruction page index:
Clip-in installation
Screw-in installation
Magnetic installation
Adjustable hinge mounting installation
Power feed layout guide
2 3 4 5 6
REV0.5 07272018*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Bosca - Installation Instructions
Models BOS-XX-C-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
Clip-in installation
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
E472444
Page 2 of 6
1
mounting channel
1.1
lead wires
fixture
Note: Refer to the power supply ins tallation inst ruction for
additional information.
Note: More than one person is recommended for this
installation.
1.1 Carefully remove the mounting channel from the back of the
fixture. Mounting channel is 1/2" shorter than the fixture for wire management.
3.1 Follow connector dimensions below and drill hole through surface.
3
Insert wire lead/connector through surface & snap fixture into the mounting channel to secure in place.
Female quick connect end
2
mounting channel
2.1
screw
screw
2.1 Determine the location of the fixture. Then secure the mounting channel to the surface with the provided mounting screws. When installing the mounting channel take into consideration the 1/2" shorter per wire lead/connector.
2.2 Install mounting screws every 6 inches to the center of the mounting channel.
3.2 Follow one of the two options to connect the fixture to the power supply.
Option 1- Secure female quick connect to male quick connect. Feed male quick connect wire through conduit to power supply.
to power supply
Male quick connect end
Lead wire end
Female/male adapter
4
120 VAC
0.45"
0.38"
0.20"
0.45"
mounting channel
4.1
class II power supply
wires from
fixture
3.1
Option 2- Feed wire whip to the power supply.
fixture
4.1 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the fixture to power supply -24VDC black wire with a wire nut.
24 VDC
to fixture
3.2
OR
wires from
fixture
female quick connect
3.2
+24 VDC RED
-24 VDC BLACK
+24 VDC RED
-24 VDC BLACK
male quick connect
REV0.5 07272018*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Bosca - Installation Instructions
Models BOS-XX-S-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
Screw-in installation
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
E472444
Page 3 of 6
1
set screw
2
2.1
mounting
bracket
1.1
fixture
mounting bracket
1.1 Install brackets 4” from each end and 30” in between the fixtures. Line up each mounting bracket to the back on the fixture & insert the edge of the clip into the fixture. Then rotate and push clip in until you feel a click. Followed by tightening the set screw using the Allen wrench (provided). Repeat for the remaining brackets.
1.1
fixture
2.1
1.1
completely installed
fixture
Note: Prior t o installation all 24VDC wires must be present
near fixture. Refer to the power supply inst allation ins truction for additional information.
2.1 Determine the location of the fixture. Then secure the fixture to the surface using the provided mounting screws.
Note: More than one person is recommended for this
installation.
3.1 Follow one of the two options to connect the
fixture to the power supply.
3
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect wire through conduit to power supply.
wires from
fixture
to power supply
male quick connect
female quick connect
4
4.1
class II power supply
OR
Option 2- Feed wire whip to the power supply.
wires from
fixture
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
120 VAC
screw
4.1 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the fixture to power supply -24VDC black wire with a wire nut.
24 VDC
to fixture
+24 VDC RED
-24 VDC BLACK
+24 VDC RED
-24 VDC BLACK
REV0.5 07272018
Bosca - Installation Instructions
Models BOS-XX-M-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
Magnetic installation
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
1
fixture
1.1
1.1
Page 4 of 6
metal backing
E472444
metal backing
fixture
Note: Prior t o installation all 24VDC wires must be present
near fixture. Refer to the power supply inst allation ins truction for additional information.
Note: More than one person is recommended for this
installation.
2.1 Follow one of the two options to connect the
fixture to the power supply.
2
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect wire through conduit to power supply.
wires from
fixture
to power supply
male quick connect
female quick connect
OR
Option 2- Feed wire whip to the power supply.
wires from
fixture
1.1 Determine the location of the fixture. Must be made of steel or a ferrous metal. Clean the surface area thoroughly from any debris. Snap the fixture onto the metal surface. If necessary fixture can easily be removed by rotating off the surface and repositioning correctly.
3
3.1
120 VAC
3.1 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the
class II
fixture to power supply -24VDC
power
black wire with a wire nut.
supply
24 VDC
to fixture
+24 VDC RED
-24 VDC BLACK
+24 VDC RED
-24 VDC BLACK
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
REV0.5 07272018
Bosca Wet - Installation Instructions
Models BOSW-XX-AH-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
Adjustable hinge installation
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
E472444
Page 5 of 6
1
fixture
screw
1.1 Slightly loosen both screws on the sides of the hinge bracket. Rotate the fixture to expose mounting hole.
2.1 Follow one of the two options to connect the fixture to the power supply.
2
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect wire through conduit to power supply.
wires from
fixture
female quick connect
1.1
mounting bracket
mounting hole
1.1
mounting bracket
to power supply
male quick connect
OR
4
2
2.1
2.1
Note: Prior t o installation all 24VDC wires must be present
near fixture. Refer to the power supply inst allation ins truction for additional information.
Note: More than one person is recommended for this
installation.
2.1 Determine the location of the fixture. Then secure the fixture to
the surface using the provided mounting screws.
2.2 Rotate the fixture to the desired angle then tighten the side screws to secure.
4.1 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red wire with a wire nut. Connect -24VDC black wire from the
class II
fixture to power supply -24VDC
power
4.1
black wire with a wire nut.
supply
+24 VDC RED
-24 VDC BLACK
Option 2- Feed wire whip to the power supply.
wires from
fixture
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV0.5 07262018
120 VAC
24 VDC
to fixture
+24 VDC RED
-24 VDC BLACK
Bosca - Installation Instructions
Models BOS-XX-M-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
multiple powerfeed layouts
power supplies at the
end of the run
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
power supply
low voltage wires
E472444
Page 6 of 6
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
fixture 1
power supply
power supply
low voltage wires
fixture 1 fixture 2
power supply
low voltage wires
fixture 1
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
low voltage wires
fixture 2
REV0.5 07272018
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use