Lumens Technology PS600 User Manual

PS600

Digital Visualizer

User Manual-English

English - 0

TABLE OF CONTENTS

COPYRIGHT INFORMATION................................................................................3

CHAPTER 1 PRECAUTIONS................................................................................4

　 SAFETY PRECAUTIONS ....................................................................................5

　 FCC WARNING ................................................................................................5

　 EN55022 (CE RADIATION) WARNING ............................................................5

CHAPTER 2 PACKAGE CONTENT.....................................................................7 T

CHAPTER 3 PRODUCT OVERVIEW...................................................................8

3.1 FRONT VIEW/ REAR VIEW................................................................................8

3.2 CONTROL PANEL .............................................................................................9

3.3 I/O CONNECTOR ............................................................................................10

3.4 REMOTE CONTROL ........................................................................................11

CHAPTER 4 INSTALLATION..............................................................................12

4.1 SETUP THE DIGITAL VISUALIZER ...................................................................12

4.2 POWERING ON THE DIGITAL VISUALIZER.......................................................12

4.3 POSITIONING AND TURNING ON THE LAMPS..................................................13

4.4 USING THE MOUSE ........................................................................................13

4.5 USING USB AND RS232 ...............................................................................13

4.6 USING ETHERNET ..........................................................................................14

CHAPTER 5 USING THE DIGITAL VISUALIZER............................................15

5.1 GETTING STARTED ........................................................................................15

5.1.1 Select Input Source.....................................................................15

5.1.2 Lamp adjustment..........................................................................15

5.1.3 Focus...............................................................................................15

5.1.4 PBP ..................................................................................................16

5.1.5 View remote object：..................................................................16

5.1.6 View transparency (Film/slide) ：...........................................17

5.1.7 Brightness......................................................................................17

5.1.8 Text/ Photo mode.........................................................................17

5.1.9 To show the captured image (StorageÆPlay) ......................18

5.1.10 To delete the captured image (Storage Æ Delete)...............18

5.2 USING THE OSD MENU .................................................................................19

5.2.1 Showing the Main Menu：.........................................................19

5.2.2 Adjusting and confirm the settings：.....................................19

5.3 OSD MENU....................................................................................................20

5.4 NETWORK SETTING .......................................................................................22

English - 1

5.5 STORAGE AFTER USE ....................................................................................23

CHAPTER 6 Q & A................................................................................................24

English - 2

Copyright Information

Copyright © Lumens Digital Optics Inc. All rights reserved.

Lumens Digital Optics Inc. is in process the trademark registration of Lumens.

No part of this document may be copied, reproduced, or transmitted by any means,

without prior written permission from Lumens Digital Optics Inc. Except

documentation kept by the purchaser for backup purposes.

In the interest of continuing product improvement, Lumens Digital Optics Inc.

reserves the right to change product specifications without notice. Information in this

document may change without notice.

Products and corporate names appearing in this manual may or may not be

registered trademarks or copyrights of their respective companies, and are used

only for identification or explanation and to the owners’ benefit, without intent to

infringe.

Disclaimer: Lumens Corporation shall not be liable for technical or editorial errors or

omissions.

English - 3

Chapter 1 Precautions

Always follow these safety instructions when setting up and using the Digital
Presenter:

1. Do not place the Digital Presenter on an unstable trolley, stand or table.

2. Do not use the Digital Presenter near water or source of heat.

3. Use attachments only as recommended.

4. Use the type of power source indicated on the Digital Presenter. If you are

not sure of the type of power available, consult your dealer or local electricity

company for advice.

5. Place the Digital Presenter can be easily unplugged.

6. Always take the following precautions when handling the plug. Failure to do

so may result in sparks or fire.

 Ensure the plug is free of dust before inserting it into a socket.

 Ensure that the plug is inserted into the socket securely.

7. Do not overload wall sockets, extensions leads or multi-way plug boards as

this may cause fire or electric shock.

8. Do not place the Digital Presenter where the cord can be stepped on as this

may result in fraying or damage to the lead or the plug.

9. Unplug the projector form the wall socket before cleaning. Use a damp cloth

for cleaning. Do not use liquid or aerosol cleaners.

10. Do not block the slots and openings in the projector case. They provide

ventilation and prevent the Digital Presenter from overheating. Do not place

the Digital Presenter on a sofa, rug or other soft surface or in a built-in

installation unless proper ventilation is provided.

11. Never push objects of any kind through cabinet slots. Never allow liquid of

any kind to spill into the Digital Presenter.

12. Except as specifically instructed in this User’s Manual, do not attempt to

operate this product by yourself. Opening or removing covers may expose

you to dangerous voltages and other hazards. Refer all servicing to licensed

service personnel.

13. Unplug the Digital Presenter during thunderstorms or if it is not going to be

used for an extended period, do not place the Digital Presenter or remote

control on top of beat-emitting equipment or heated objects such as a car

and etc.

14. In the following situations, unplug the Digital Presenter from the wall outlet

and refer servicing to licensed service personnel:

English - 4

 If the power cable or plug becomes damaged or frayed.

 If liquid is spilled into it or the Digital Presenter has been exposed to

rain or water.

¾ Safety Precautions

Warning: To reduce the risk of fire or electric shock, do not expose
this appliance to rain or moisture.

This Digital Presenter has a 3 wires AC line Plug. This is a safety feature to ensure

that the plug will fit into the power outlet. Do not try to defeat this safety feature.

If the Digital Presenter will not be used for an extended time, unplug it from the

power outlet.

CAUTION

Caution: To reduce the risk of electric shock. Do not remove cover (or back). No
user-serviceable parts inside. Refer servicing to licensed service Personnel.

This symbol indicates that
dangerous voltage
constituting a risk of
electric shock is present
within this unit.

RISK OF ELECTRIC SHOCK

This symbol indicates that
there are important operating
and maintenance
instructions in this User’s
Manual with this unit.

¾ FCC Warning

This Digital Presenter has been certified to comply with the limits for a Class A

computing device, pursuant to Subpart J of Part 15 of FCC Rules. These limits are

designed to provide reasonable protection against a harmful interference when the

equipment is operated in a commercial environment.

¾ EN55022 (CE Radiation) Warning

This product is intended for use in a commercial, industrial, or educational

environment. It is not intended for residential use.

English - 5

This is a Class A product. In a domestic environment it may cause radio

interference, in which case the user may be required to take adequate measures.

The typical use is in a conference room, meeting room or auditorium.

English - 6

Chapter 2 Package Content

Please make sure the package comes with the following items when you unpack:

PS600 Quick start guide User Manual

CD Power Cable USB Cable

C-Video Cable

VGA Cable Remote Control

English - 7

Chapter 3 Product Overview

3.1 Front View/ Rear View

1. Camera Head

2. Camera Arm

3. Lamp

4. Backlight

5. Remote Control
Slot

6. CF card slot

7. Lamp lock

8. Control Panel

9. Button Function
Guide

10. IR Sensor

English - 8

3.2 Control Panel

1. Power：

Power on/off

2. Source：

Select PC or Camera to Projector

3. Lamp：

Switch / on / off the lamp and backlight

4. Photo/Text：

Select the photo or text mode

5. AF：

Auto Focus

6. Brightness +/–

Brightness Adjustment

7. Zoom + /–

zoom in/out

8. A4/A5：

Speedy zoom to A4/ A5 size

9. AWB/Shift：

AWB is Auto White Balance; Shift function enables

in PBP mode that can be shifted the other half

10. Capture

Capture an image into internal memory

or storage card

11. Freeze
Freeze the live image

12. PBP

Compare the live image and

captured image

13. Menu
Entry the OSD menu

14. Enter： Enter

15. Lock/ Unlock

Enable / Disable the Capture,

PBP, AWB, Freeze etc

English - 9

3.3 I/O Connector

1. VGA IN

Connect to VGA-out of other device for example PC

2. VGA OUT

Connect to VGA-in of another visual device

3. DVI OUT

Digital & Analog Receptacle Connector

4. LCD Monitor
External small size LCD monitor

5. C-VIDEO
C-Video for video output

6. Ethernet
Ethernet connection For remote central control

7. USB ( support USB 1.1 )

Ethernet connection For remote central control

8. PS2

Connect with PS/2 mouse

9. RS232

Connect external device with RS232

10. DC 12V output
Output the 12V (DC) from Digital Presenter, such as the backlight.

11. AC-in

Use this to connect the power cable (100 - 240V) for the power input

English - 10

3.4 Remote Control

1. Power：

Power on/off

2. Capture：

Capture image to internal
memory

3. Source：

Select PC or Camera to
Output

4. AF：

Auto Focus

5. PBP：

Compare the live image and

captured image

6. Menu：

Display full control menu

(OSD Menu)

7. BRT+/-：
Brightness adjustment

8. Photo/ Text ：

Change between Photo or

Text mode

9. Play：

Recall the saved images in

the Digital Visualizer

10. A4/A5：

Speedy zoom to A4/ A5 size

11. Del：

Delete the saved images in
the Digital Visualizer

12. Flip：

Rotate the image by 180°

13. Freeze
Freeze the image on screen

14. AWB：

Auto White Balance

English - 11

15. Preset：

Save/load your setting

parameters (like brightness,)

16. Lamp：

Switch / on / off the lamp and
backlight

17. Focus +/-：
Manual focus for fine tune

18. Enter：

Enable the selected function

19. Auto Tune：

Auto-adjust for optimum

image

20. Zoom + /– ：

Zoom adjustment

21. Shift：

PBP image can be shifted the
other half

※Caution：

1. To avoid unexpected electric shock or explosion,

use the applicable batteries is the must.

2. Recyle the exhausted or damaged batteries by
following the instructions.

(Refer to 5.1.5 )

Chapter 4 Installation

4.1 Setup the Digital Visualizer

1. Pull up the arm. Adjust the position and height (the height should
be 48.5 cm for operation) of the arm by moving the 3-section joint

2. Turning the camera head toward the platform

※ Note：The angle of the camera head is limited. Don’t turn it

forcefully when it reaches the maximal angle

4.2 Powering on the Digital Visualizer

※Note：Before using the Digital Presenter, make sure that you have

English - 12

connected it to the computer, video source or other output devices.
See Figure: 3-3, Rear View for the position of connector jack.

1. Connect the power cable to the AC IN jack

2. Press
Digital Presenter. The red LED (flashing until the presenter is
started) turns to green

(the Power button) for about 1 second to power on the

4.3 Positioning and Turning on the Lamps

You can use the lamps on the both sides of the Digital Presenter for
auxiliary lighting by following some simple steps：

1. Press and slide the latches to release the lamp lock.

2. Pull up the lamp arms.

3. Rotate the folded lamp to face the platform as the
arrow shows. (Refer to figure 4-1)

4. Press the lamp button of control panel and remote control to switch
the side lamp or backlight.

※ Note： The angle of the lamp arm/lamp head is limited.

Do not turn it forcefully when it reaches the maximal angle

4.4 Using the Mouse

You can also control the Digital Presenter by a PS2 mouse (see the figure
3-3 for PS2 connection). For example, you can move the cursor to adjust
the settings or use the cursor as a pointer for Presenter.

¾ Mouse Keys

The left key functions as Enter. The right key is used for activating the
menu. The central key/bar (when available) is for moving your
selection on the menu.

4.5 Using USB and RS232

¾ USB

You can transmit images to computer via USB interface. To enhance
USB transmission, make sure that your PC supports USB protocol (the
Digital Presenter is based on USB 1.1). An updated driver is available
on the Lumens website (

¾ RS232

RS232, a kind of serial protocol, facilitates remote control functions.
For example, you can control the Digital Presenter installed in a
conference room from a PC in another building via RS232.

English - 13

http://www.lumens.com.tw/)

4.6 Using Ethernet

The Digital Visualizer can be controlled via the internet.

1. Please connect the RJ-45 to Ethernet port (refer to the 3.3
I/O connection)

2. Select the setting of DHCP, IP, Net Mask and Gate Way.
Please refer to the 5.4 Network setting steps.

3. Open the Internet Browser and key in the IP in the address
field. The remote control will be shown as following then you
can control the main unit remotely via internet.

Note※ ：If you can’t use the Ethernet , please consult the network or MIS

administrator to get help

English - 14

Chapter 5 Using the Digital Visualizer

This chapter shows you the basic and advanced functions of the Digital Presenter
as and how to use the menu, the mouse, and the Presenter USB/RS232 interface

5.1 Getting Started

5.1.1 Select Input Source

Switch the video input from PC or
Camera

¾ Option1：press <SOURCE> button on the control panel

¾ Option2：press

※Note：Input source can be shown on the indicator of control panel

5.1.2 Lamp adjustment

¾ Press (Lamp) on the control panel or Remote Control to turn

on and off the lamps and the backlight.

※Note：The lamp and backlight can not be turned on in the same

time.

5.1.3 Focus

¾ Speed zoom to A4 or A5 size

Option1：press <A4 A5> button on the control panel

Option 2：press

¾ Auto Focus：

option1：press <AF> on the control panel

on the remote control

or on remote control

English - 15

option2：press on the remote control

※Note：The digital visualizer will execute the Auto Focus after

zoom in/ out

¾ Manual Focus

option1：press <ZOOM> +/- on the control panel

option2：press

※Note：The optical zoom will be automatically switched to the

digital zoom at the last step of the optical zoom

5.1.4 PBP

Display current live image and captured image for side-by-side
comparison

［A］

live image

［B］

1/2 Capture

image

¾ Option1：press <PBP>Æselect captured picturesÆ<ENTER>

You can press <AWB/Shift> to show the captured image at the
other side

¾ Option2：press

on the remote controlÆselect captured

picturesÆ

¾ Shift to show another side captured image (PBP function

enables in PBP mode)

5.1.5 View remote object：

¾ Pull out the close-up lens, as shown in following pictures

English - 16

¾ Rotate the camera head

¾ While observing the image on the monitor, adjust the zoom or

arm to obtain the optimal size

¾ To rotate the image by 180º

Optoin1：press <MENU> then select Flip from OSD Menu

Optoin2：press

5.1.6 View transparency (Film/slide) ：

Option1：press <LAMP> on the control panel to switch backlight

Option2：press

5.1.7 Brightness

Option1：press <BRIGHTNESS>+/- on the control panel

Option2：press

Option 3：press

※Note：You may also adjust the lamps for proper lighting or turn

on/off the lamps.

5.1.8 Text/ Photo mode

「Photo mode」：For image use

「Text mode」：For document use

on the remote control

on the remote control to switch backlight

on the remote control

on the remote control

Option 1：press <TEXT/PHOTO> on the control panel

English - 17

Option 2：press on the remote control

5.1.9 To show the captured im ag e (StorageÆPlay)

Option 1：OSD／Storage ／Play

In the Index screen, the captured images were
displayed in thumbnails. Whenever the box is on a
thumbnail, you may see the full and large image by
Enter click.

Option 2：Press on the remote control and select image by

using

key to see the large image

keys then press the

5.1.10 To delete the captured image (Storage Æ Delete)

Option 1：OSD／Storage ／Delete

※Note：If you perform the "Delete " function, you may not delete

any image unless you have selected the file and enlarged
it.

Option 2：Press on the remote control to enter the image

index screen. Select an image by using
keys and press< Del> button to delete.

English - 18

5.2 Using the OSD Menu

5.2.1 Showing the Main Menu：

Option 1：Press <MENU> on the control panel

Option 2：Press

Option 3：Press right button of the PSII mouse

※Note：The menu will be automatically turned off when not being

activated for a while.

5.2.2 Adjusting and confirm the settings：

Move your mouse to highlight the option your want to select. If
you are using the remote control, show the Main Menu and
highlight the option you want to select by pressing
► buttons.

¾ Confirm a setting：

Press the
confirm the option you choose

¾ Exit the setting：

Option 1：Press <MENU> on the control panel

on the remote control

, , ◄, or

on your remote control or click the mouse to

Option 2：Press

Option 3：Press right button of the PSII mouse

on the remote control

English - 19

5.3 OSD Menu

Layer 1 Layer 2 Layer 3 Content

Normal：default
Gray：Black & while picture
Film：in the backlight mode
Slide： in the backlight mode

(Your presenter will automatically
adjust the image size, brightness,
color, lamps, and AF, based on
your selection of Slide or Film
modes.)

Enable is default

Flip by 180°
(Up→Down & Left→Right )

exposing effect of the image
automatically

Select color temperature

Display

Image

Normal/Gray/Film/
Slide/Microscope

Flip Enable/Disable

AE

On (default)／Off

Color Temp. Warm/Middle/Cool

Output Mode

XGA 60Hz / SVGA
60 Hz

Focus

Select video output

Adjust image focus

Play Show captured images

Delete Delete captured images

Delete All Enter / Exit Delete all captured images

Storage

Format Media Enter / Exit Format

Media Internal / PC card Select storage

Delete all captured images

Auto Erase On / Off

when user turn off the power.

English - 20

Layer 1 Layer 2 Layer 3 Content

Point Color Red / Green / Blue Select the cursor’s color

Drawing Type Frame / Line

Video Format Auto / NTSC / PAL

English / Deutsch /

Setting

Advance

The OSD menu is shown as below when the Input Source from PC

Layer 1 Layer 2 Content

Language

Factory Reset Enter / Exit Reset all default setting

Preset Save/load

DHCP Enable / Disable

IP Set IP address

Net Mask Set Net Mask value

Gate Way Set Gate Way value

Francais / Italiano/
Eapanol / Русский /

/

Select your native language

Save/load setting
parameters

Set DHCP (Dynamic Host
Configuration Protocol)

Clock Set the clock

Phase Set the phase

H-Position Set the image horizontal position

PC Input

English - 21

V-Position Set the image vertical position

Brightness Set the image brightness

Contrast Set the image contrast

Auto Image

Auto. set clock & Phase & Position & Brightness
& Contrast

5.4 Network Setting

Step1：Confirm the Ethernet has been connected

Step2：Press <MENU> button on the control panel or entry the

OSD Menu by remote control

Step3：Select “Advance”

¾ DHCP：Dynamic Host Configuration Protocol is an Internet

protocol for automating the configuration of computers.

※Note：Please confirm the DHCP server is available before

use it.

¾ Default is Disable：For static IP address

Please key in the IP, Net Mask, Gate Way value and save
them if you know. Otherwise, please consult the network or
MIS administrator to get help.

¾ Enable：For public IP address

Please restart the Visualizer after the DHCP was enabled. The
IP, Net Mask and Gate Way value can be got automatically by
DHCP.

English - 22

5.5 Storage after Use

1. Fold the arm and camera head until they touch the stage

2. Turn the camera head until it’s parallel with the stage

3. Turn the upper lamps toward the supporting arms

4. Insert the remote control into the slot on the right of the Digital Visualize

5. Fold them to both sides of the Digital Visualizer until they lock in both side

English - 23

Chapter 6 Q & A

This chapter describes the problems you might have encountered when you use
this Digital Presenter. If you have a problem, refer to the appropriate section and
follow all the suggestions that apply to your problem. If none of the suggested
solutions solves the problem, call your dealer or your service center.

z Q1:The (

Ans1:

No power is coming on. Check that the power cord is connected securely

both at the power outlet and the PS

z Q2: No imag e ap p e ars on th e s cre e n .

Ans2：

1. Make sure the power is installed correctly and securely.

2. Make sure all of the cables are installed correctly and securely.

3. Check the power of LCD monitor or projector is turn on

4. Make sure the objector is positioned in the shooting area.

z Q3：The image or parts of the image are blurred or not in focus

Ans3：

The lens focusing is maybe not correct or the image sampling is not in the
best condition. Press the AF (Auto Focus) on the remote control or the
control panel.

z Q4：Image is too dark or too bright

Ans4：

Press the<BRIGHTNESS >+/- on the control panel or remote Control to
adjust the brightness setting.

z Q5：All buttons on the control panel are disable

Ans5：

Press both <MENU> & <ENTER> keys simutaneously to
unlock all buttons. If that is not work, please turn off the
power and wait few seconds then restart the main unit.

z Q6：Remote Control does not work.

Ans6：

1. Please make sure the remote control aimed at
the IR sensor

2. Please check the battery

＊ The updated information will be regularly released on Lumens web site, please

visit our web site

English - 24

) system indicator does not come on.

IR sensor

http://www.lumens.com.tw for the most update