DC133
Digital Visualizer
User manual
English - 1
Table of Contents
COPYRIGHT INFORMATION ................................................................................ 4
CHAPTER 1 PRECAUTIONS ................................................................................ 5
CHAPTER 2 PACKAGE CONTENT ......................................................................7
CHAPTER 3 PRODUCT OVERVIEW .................................................................... 8
3.1 PRODUCT INTRODUCTION .................................................................... 8
3.2 I/O CONNECTION ................................................................................. 9
3.3 DIP SWITCH........................................................................................ 9
3.4 REMOTE CONTROL ............................................................................ 10
CHAPTER 4 HOW TO USE IT ............................................................................. 11
4.1 GETTING STARTED ............................................................................ 11
4.1.1 TURN ON THE DIGITAL VISUALIZER ................................................. 11
4.1.2 LENS FOCUS.................................................................................. 11
4.1.3 ZOOM IN / OUT............................................................................... 11
4.2 GENERAL FUNCTIONS........................................................................ 12
4.2.1 SWITCH SOURCE............................................................................12
4.2.2 PHOTO/TEXT ................................................................................. 12
4.2.3 ZOOM IN / OUT .............................................................................13
4.2.4 ADJUST BRIGHTNESS .................................................................... 13
4.2.5 OSD MENU ................................................................................... 13
4.2.6 OSD FUNCTION SELECT ................................................................ 14
4.3 ADVANCED........................................................................................ 14
4.3.1 CAPTURING IMAGE......................................................................... 14
4.3.2 PLAYING IMAGE ............................................................................. 14
4.3.3 DELETE IMAGES ............................................................................ 15
CHAPTER 5 OSD MENU INTRODUCTION ........................................................17
5.1 OPERATION MENU ............................................................................. 17
English - 2
5.2 OSD MENU....................................................................................... 17
CHAPTER 6 TROUBLESHOOTING....................................................................20
English - 3
Copyright Information
Copyright © Lumens Digital Optics Inc. All rights reserved.
Lumens Digital Optics Inc. is in process the trademark registration of Lumens.
No part of this document may be copied, reproduced, or transmitted by any means, without
prior written permission from Lumens Digital Optics Inc. Except documentation kept by the
purchaser for backup purposes.
In the interest of continuing product improvement, Lumens Digital Optics Inc. reserves the
right to change product specifications without notice. Information in this document may
change without notice.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification
or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer: Lumens Corporation shall not be liable for technical or editorial errors or
omissions.
Patent: M286526 & I260916 (Taiwan) & ZL 2005 2 0129210.7 (China)
English - 4
Chapter 1 Precautions
Always follow these safety instructions when setting up and using the Digital Visualizer:
Do not place the Digital Visualizer on an unstable trolley, stand or table.
1.
2.
Do not use the Digital Visualizer near water or source of heat.
3. Use attachments only as recommended.
4.
Use the type of power source indicated on the Digital Visualizer. If you are not sure of
the type of power available, consult your dealer or local electricity company for
advice.
5.
Place the Digital Visualizer can be easily unplugged.
6.
Always take the following precautions when handling the plug. Failure to do so may
result in sparks or fire.
Ensure the plug is free of dust before inserting it into a socket.
Ensure that the plug is inserted into the socket securely.
7. Do not overload wall sockets, extensions leads or multi-way plug boards as this may
cause fire or electric shock.
8.
Do not place the Digital Visualizer where the cord can be stepped on as this may
result in fraying or damage to the lead or the plug.
9.
Unplug the projector form the wall socket before cleaning. Use a damp cloth for
cleaning. Do not use liquid or aerosol cleaners.
10.
Do not block the slots and openings in the projector case. They provide ventilation
and prevent the Digital Visualizer from overheating. Do not place the Digital
Visualizer on a sofa, rug or other soft surface or in a built-in installation unless proper
ventilation is provided.
Never push objects of any kind through cabinet slots. Never allow liquid of any kind
11.
to spill into the Digital Visualizer.
12.
Except as specifically instructed in this User’s Manual, do not attempt to operate this
product by yourself. Opening or removing covers may expose you to dangerous
voltages and other hazards. Refer all servicing to licensed service personnel.
13.
Unplug the Digital Visualizer during thunderstorms or if it is not going to be used for
an extended period, do not place the Digital Visualizer or remote control on top of
beat-emitting equipment or heated objects such as a car and etc.
14.
In the following situations, unplug the Digital Visualizer from the wall outlet and refer
servicing to licensed service personnel:
If the power cable or plug becomes damaged or frayed.
If liquid is spilled into it or the Digital Visualizer has been exposed to rain or
English - 5
water.
Safety Precautions
Warning: To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
This Digital Visualizer has a 2 wires AC line Plug. This is a safety feature to ensure that the
plug will fit into the power outlet. Do not try to defeat this safety feature.
If the Digital Visualizer will not be used for an extended time, unplug it from the power
outlet.
CAUTION
Caution: To reduce the risk of electric shock. Do not remove cover (or back). No
user-serviceable parts inside. Refer servicing to licensed service Personnel.
This symbol indicates that
dangerous voltage
constituting a risk of electric
shock is present within this
unit.
RISK OF ELECTRIC SHOCK
This symbol indicates that
there are important operating
and maintenance instructions
in this User’s Manual with this
unit.
FCC Warning
This Digital Visualizer has been certified to comply with the limits for a Class A computing
device, pursuant to Subpart J of Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against a harmful interference when the equipment is
operated in a commercial environment.
EN55022 (CE Radiation) Warning
This product is intended for use in a commercial, industrial, or educational environment. It
is not intended for residential use.
This is a Class A product. In a domestic environment it may cause radio interference, in
which case the user may be required to take adequate measures. The typical use is in a
conference room, meeting room or auditorium.
English - 6
Chapter 2 Package Content
Please make sure the package comes with the following items when you unpack: (11
items)
Main Unit Quick Start Guide User’s Manual
CD Power Cable VGA Cable
USB Cable Remote C-Video Cable
Soft Bag (Big) Soft Bag (Small)
English - 7
Chapter 3 Product Overview
3.1 Product Introduction
Lens
Power/Control keypad
Infrared rays area
Lamp
Gooseneck
I/O Port
English - 8
DIP Switch
3.2 I/O Connection
3.3 DIP Switch
The default settings are listed below！
3.4
ON
OFF
(Default)
English - 9
AE ON C-Video PAL SVGA
12 34
AE OFF RGB NTSC XGA
(OFF at all time)
Remote Control
1
1. Power:
2. Capture:
3. Freeze:
4. AWB:
5. Menu:
6. BRT+/-:
7. ghij / Enter:
*Only use CR2025 as replacement battery. Dispose used battery properly please.
4
7
7
10
12
13
11
Turn on/ off.
Capture the image
Freeze the image
Auto white balance
Show the Control Menu (OSD Menu)
Adjust the image brightness
g h i j
function item, then p
select the desired
ress Enter to
take effect
English - 10
9
8. Zoom +/-:
Make the image larger & smaller
9. Play／Del:
Recall／Delete the saved
images in the flash memory of
your Digital Visualizer.
10. Flip:
Rotate the image by 180 degrees
11. Lamp:
Turn on/ off Lamp
12. Source:
Switch between different signal
sources
13. Photo/ Text:
Select the text or photo mode
5
6
8
Chapter 4 How to use it
4.1 Getting Started
4.1.1 Turn on the Digital Visualizer
4.1.2 Lens focus
¾ Turn the lens to optimize the focus
4.1.3 Zoom in / Out
Keypad
Remote
¾ Press the control button on the remote controller
English - 11
4.2 General Functions
4.2.1 Switch source
Press 『Source』to change the image source from PC. The default setting is
Digital Visualizer.
Keypad
Remote
Monitor
PC Notebook
Projector
4.2.2 Photo/Text
The default setting is『Photo』. Choose『Te xt』for displaying text file.
English - 12
Remote
4.2.3 Zoom in / Out
4.2.4 Adjust Brightness
4.2.5 OSD Menu
English - 13
4.2.6 OSD Function Select
1. Press 『^ v< >』 to search functions.
2. Press the Enter key to enable your selection.
Keypad
Remote
4.3 Advanced
4.3.1 Capturing Image
Remote：Press『Capture』to capture the image you want.
Control Panel：
1. Press『Menu』to access OSD menu.
2. Press『 T 』to choose
execute.
3. Press『 T 』to choose『Capture』.
4. Press『Enter』to execute image capturing.
5. Double click『Menu』to exit.
(Storage) and press『Enter』to
4.3.2 Playing Image
Remote：
1. Press『Play』to display all the images.
2. Press『ef』to select the thumbnail picture you want to browse.
English - 14
3. Press『Enter』to display the image with full screen.
4. Press『ef』to view next image.
5. Press『Play』to go back.
6. Press『Menu』to exit.
Control Panel:
1. Press『Menu』to access OSD menu.
2. Press『 T 』to choose
execute.
3. Press『 T 』to choose『Play』
4. Press『Enter』to enter into browsing screen.
5. Press『ef 』to select the thumbnail picture you want to browse.
6. Press『Enter』to display the image with full screen.
7. Press『ef』to view next image.
8. Double click『Menu』to exit.
4.3.3 Delete Images
Remote:
1. Press『Play』to enter into browsing screen.
2. Press『ef』to choose the image you want to delete.
3. Press『Del』to delete the selected image right away.
Control Panel:
1. Press『Menu』to access OSD menu.
(Storage) and press『Enter』to
2. Press『 T 』to choose
execute.
3. Press『 T 』to choose『Play』.
4. Press『Enter』to enter into browsing screen.
5. Press『ef 』to select the thumbnail picture you want to browse.
English - 15
(Storage) and press『Enter』to
6. Press『Enter』to display the image with full screen.
7. Press『Menu』to access OSD menu.
8. Press『 T 』to choose
execute.
9. Press『 T 』to choose『Delete』
10. Press『Enter』to execute image deleting.
11. Double click『Menu』to exit.
(Storage) and press『Enter』to
English - 16
Chapter 5 OSD Menu Introduction
5.1 Operation Menu
Remote Control and Display Panel:
1. Press『Menu』to access OSD menu.
2. Press『d Sfe』to select the function that you want.
3. Press『Enter』to execute.
4. Double click『Menu』to exit the OSD menu.
5.2 OSD Menu
y There are four layers for OSD menu – Display, Setting, Source and
Storage
y After accessing into OSD menu, it will disappear automatically after
certain seconds.
¾ VGA Mode
Layer 1 Layer 2 Layer 3
Setting
Lamp
Night view
Language
Output
Format
Factory
Reset
Exit
On / Off
On / Off
English, Deutsch,
Francais, Italiano,
Espanol, Русский,
, , Exit
XGA 75Hz/XGA
60Hz/ SVGA
75Hz/ SVGA 60Hz
Enter/Exit
Select Lamp On or Off.
Function
Select Night view function On or
Off.
Select a preferred language on the
menu.
Select a fitting output format.
Reset all the values to the factory
default.
Exit menu.
English - 17
Display
Source
Storage
Brightness
Zoom
Gamma
Image
Flip
Freeze
Exit
Visualizer
VGA In
Capture
Playback
Delete
Delete All
0-46 (for PAL)
0-40 ( for NTSC)
Digital Zoom
Photo / Text Select Photo/Text Mode.
Normal / Gray / Film Select Normal/Gray/Film Mode.
On/Off Adjust the image up and down by
On/Off Use Freeze to retain the image on
Enter/ Exit
Brightness adjustment
Adjust Zoom 100% ~ 1600%.
180°.
the screen.
Exit this menu.
Select images of Visualizer or VGA
In.
Capture the image of Visualizer.
Present the captured image.
Delete the captured image.
Delete all images.
Format
Format
Memory Format
Enter/ Exit
Memory Format
Exit menu.
Exit menu.
English - 18
¾ C-Video Mode
Layer 1 Layer 2 Layer 3 Function
Display
Setting
Brightness
Gamma
Image
Freeze
Exit
Lamp
Advance
Language
Factory
Reset
Exit
0-46 (for PAL)
0-40 ( for NTSC)
Photo/Text Select Photo/Text Mode.
Normal/Gray Select Normal/Gray Mode.
On/Off
Exit this menu.
On/Off Turn On/Off lamp
Full Range On/off
Night view On /off
Exit
English/
/Exit
Enter / Exit
Exit this menu.
, ,
Brightness adjustment
Use Freeze to retain the image on
the screen.
Switch Full range on/off and night
view on/off
Select a preferred language on the
menu.
Reset all the values to the factory
default.
Exit menu.
English - 19
Chapter 6 Troubleshooting
This chapter describes the problems you might have encountered when you use this Digital
Visualizer. If you have a problem, refer to the appropriate section and follow all the
suggestions that apply to your problem. If none of the suggested solutions solves the
problem, call your dealer or your service center.
Problem 1: No picture from the Digital Visualizer.
Solution -
1: Wait a few seconds, press desired source selector again.
2: Press a different source, then press-desired source again.
3: Check if the power of the Digital Visualizer is turned on.
4: Make sure the document or object is positioned under the camera.
Problem 2: Cannot Focus, camera will not focus properly.
Solution - To properly focus: Zoom in as far as possible on the document or object,
focus and then zoom out to desired distance.
Problem 3: Image is too bright or dark can not see desired part of the image because
it is too bright or dark.
Solution – Adjust the Control Button on the Digital Visualizer.
*
The updated information will be regularly released on Lumens web site, please visit our
web site http://www.lumens.com.tw for the latest information.
English - 20
Loading...