IMPORTANT INSTRUCTIONS
For Installation LS482
MODELS LS482
Mains Voltage depicted 12V version available
Check fixture for wattage.
A.C.N. 010 572 773
Note: To achieve IP66 rating, use round cable (size 5-10mm) to suit entry gland supplied with fixture.
1
Surface Mount Plate
Mounting fasteners
not supplied by
Lumascape
Hole Size Ø11mm
PCD Ø120mm
Outside Diameter
Ø150mm
Direct Burial Post
300mm (11.8in)
Discreet Mount
Mounting fasteners
not supplied by
Lumascape
2 3
Insert lamp into fixture
Check wattage and
insert lamp into fixture.
Test to ensure lamp and
fixture is operational.
INC.
LUMASCAPE USA INC.
US Head Office
1300 Industrial Rd., Unit #19
San Carlos, CA 94070
USA
Telephone
1-(650)-595-LUMA(5862)
Fax
1-(650)-595-5820
www.lumascape.com
Free Call
1-866-695-LUMA(5862)
(US & Canada)
Wire up fixture
Remove lid from fixture
and pull out gear tray.
Pull cable through gland
and tighten.
Connect leads to
terminal block.
Slide gear tray back into
mounting pole.
Warning
Rubber seal protects gear tray from moisture.
Do not use force. Make sure seal fits tightly against pole.
Fit cover & seal
Put lid on fixture
and seal by
tightening all
three screws
around the base.
Relamping4
12Open fixture as shown in .
Remove old lamp from fixture as shown below.
step 2
34Insert lamp into fixture as shown in .
Seal fixture as shown in .
step 5
step 4
C1317US - 2006_07_REV001
INC.
MODELS LS482-293XXXQX BI-PIN INTEGRAL
12V 50watt Halogen Bi-pin Max.
LS482-293XXXRX BI-PIN REMOTE
12V 50watt Halogen Bi-pin Max.
IP66 rated
IMPORTANT INSTRUCTIONS
For Installation LS482 Halogen Bi-Pin
Warning: The Luminaire should only be used complete with its protective shield (cover)
1
Surface Mount Plate
Hole Size Ø0.4” (11mm)
PCD Ø4.7” (120mm)
Outside
Mounting fasteners
not supplied by
Lumascape
33
INTEGRAL MODEL
WIRING ONLY:
Remove gear tray
from post.
Pull cable through
gland and tighten.
Connect leads to
terminal block.
Ensure that the earth
terminal is fitted to the
inside of the post.
Slide gear tray back
into the post.
Direct Burial Post
300mm (11.8in)
Discreet Mount
Mounting fasteners
not supplied by
Lumascape
REMOTE MODEL
WIRING ONLY:
Remove gear tray
from post.
Pull cable through
gland and tighten.
Connect leads to
terminal block.
Slide gear tray back
into the post.
Lumascape USA Inc.
1300 Industrial Rd., Unit #19
San Carlos, CA 94070, USA
T 1-(650)-595-LUMA(5862)
F 1-(650)-595-5820
E info@lumascape.com
W www.lumascape.com
Free Call US & Canada1-866-695-LUMA(5862)
2
Check the lamp wattage and insert
4
the lamp into the lampholder.
Test to ensure that the lamp and
fixture is operational.
Remove the head
from the post by
unscrewing the
three screws.
5
Lumascape USAInc. 2006©
Important Notes:
Rubber seal protects
gear tray from moisture.
Do not use force.
Make sure seal fits
tightly against post.
Fit the head
onto the post
and seal by
tightening all
three screws.
OR
Relamping
12Remove head as shown in .
Remove old lamp from fixture as shown.
34Insert lamp into fixture as shown in
Seal fixture as shown in .
www.lumascape.com
LUMASCAPE USA INC
Free Call 1-866-695-LUMA(5862)
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
Important Notes:
Rubber seal protects
gear tray from moisture.
Do not use force.
Make sure seal fits
tightly against post.
step 2
step 4.
step 5
C1778US 09_2006
MODELS LS482-291XXXRX E26 / E27
.CNI
120V 60watt Incandscent Max.
120V 23watt Self-ballasted CFL Max.
IP66 rated
IMPORTANT INSTRUCTIONS
For Installation LS482 E26 / E27
Warning: The Luminaire should only be used complete with its protective shield (cover)
Wiring Connections
1
Surface Mount Plate
Hole Size Ø0.4” (11mm)
PCD Ø4.7” (120mm)
Outside
Supply
Mounting fasteners
not supplied by
Lumascape
3 4
Pull out gear tray and make connections
to supply cable.
Discreet Mount
Mounting fasteners
not supplied by
Lumascape
Re-attach earth spade connector.
Lumascape USA Inc.
1300 Industrial Rd., Unit #19
San Carlos, CA 94070, USA
T 1-(650)-595-LUMA(5862)
F 1-(650)-595-5820
E info@lumascape.com
W www.lumascape.com
Free Call US & Canada1-866-695-LUMA(5862)
2
Re-install the gear tray. Ensure bracket
5
is fitted into groove.
Remove the head
from the post by
unscrewing the
three screws.
Check the lamp wattage and insert
6
the lamp into the lampholder.
Test to ensure that the lamp and
fixture is operational.
Lumascape USAInc. 2006©
7
www.lumascape.com
Free Call 1-866-695-LUMA(5862)
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
Fit the head onto the
post and seal by
tightening all three
screws.
LUMASCAPE USA INC
Relamping
12Remove head as shown in .
Remove old lamp from fixture as shown.
34Insert lamp into fixture as shown in
Seal fixture as shown in .
step 2
step 7
step 6.
C1779US 30_2010
Loading...