Lumascape LS345 Instructions Manual

FOR UNDERWATER USE

DISCONTINUED PRODUCT

t 90 Ct 90 C

1m

A.C.N. 010 572 773

o

90

IMPORTANT INSTRUCTIONS

A

START

HERE

For Installation LS345: MH, UNDERWATER

Warning: The Luminaire should only be used complete with its protective shield (cover)

WARNING

To avoid potential unsafe lamp failure, the luminaire should be switched off at least once a week

If cable damaged replace with cable supplied by LUMASCAPE only.

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
PO Box 1875, Cleveland D.C., QLD 4163, Australia
T 07 3286 2299
F 07 3286 6599
E [e-mail]
W www.lumascape.com.au

DO NOT SHORTEN, INTERFERE OR DISCONNECT CABLE FROM FITTING. WARRANTY WILL BE VOID IF
CABLE ASSEMBLY IS TAMPERED WITH.

100MM

1 32

(3.93IN)

100-250MM

(3.93-9.84IN)

160MM

(6.3IN)

Locate Fixtures

Site fixture in proximity to cabling.
Use discretion in locating fixtures as
glass can become very hot and may
burn.

FLAT
WASHER

SPRING
WASHER

BRACKET

DOME NUT

Mount Bracket to Fixture

Mount bracket supplied to fixture using
the M10 dome nuts and washers as
shown

2 X 8MM

12MM

o

90

o

30

Mount Fixture

Mount fixture to secure surface.
Orientate fixture as required and
tighten nuts

70MM (2.75IN)

BRACKET TOP VIEW

o

90

o

30

4 65

Connect Supply

Connect fixture to supply cable according to
local wiring rules.

7 8

60

45

30

10-15 MIN.

Test Fixture

Test to ensure fixture is operational. Allow to
burn for 10-15 minutes to allow any
moisture in fixture to evaporate.

Seal Fixture

Ensure seal and sealing surface is clean.
Clean glass if necessary. Tighten lid screws
using the 3mm Allen key supplied.
Lumascape recommends tightening in the
above Torque Pattern to 2.5 - 3 N.m.
DO NOT OVER TIGHTEN.

Insert Lamp

Check lamp WATTAGE, VOLTAGE, and
TYPE, and insert into lampholder (refer to
lamp manufacturers documentation for
handling precautions).

Torque Pattern

1

6

4

3

5

2

GIMBAL
LOCKING
SCREW

GIMBAL
ROTATION
LOCKING
SCREW

Adjust Gimbal Position.

Adjust the vertical position of the gimbal to
minimise glare, and tighten locking screw.
Rotate gimbal to desired direction and
tighten locking screw.

Further
information
over page

C1612US - 2006_07_REV001

LUMASCAPE
HEAD OFFICE

T 07 3286 2299 F 07 3286 6599

Lumascape Lighting Industries 2006©

LUMASCAPE

SYDNEY - NSW

T 02 9519 6860 F 02 9519 8834

LUMASCAPE

MELBOURNE - VIC

T 03 9686 1900 F 03 9686 1700

www.lumascape.com.au

H.I. LIGHTING

LUMASCAPE AGENT - WA

T 08 9321 5422 F 08 9321 5881

LIGHTING PARTNERS AUSTRALIA

LUMASCAPE AGENT - SA

T 08 8232 0074 F 08 8232 0076

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

T 07 4031 4490 F 07 4031 5933

ECC LIGHTING

LUMASCAPE AGENT - NZ

T 09 379 9680 F 09 308 9328

LUMASCAPE USA INC

Free Call 1-866-695-LUMA(5862)

T 1-(650)-595-LUMA(5862) 1-(650)-595-5820

C1613 - 2007_01_REV-003

FOR UNDERWATER USE

DISCONTINUED PRODUCT

t 90 Ct 90 C

1m

A.C.N. 010 572 773

o

90

IMPORTANT INSTRUCTIONS

IMPORTANT INSTRUCTIONS

B

For Installation LS345 UNDERWATER

Warning: The Luminaire should only be used complete with its protective shield (cover)

To avoid potential unsafe lamp failure, the luminaire should be switched off at least once a week

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
PO Box 1875, Cleveland D.C., QLD 4163, Australia
T 07 3286 2299
F 07 3286 6599
E [e-mail]
W www.lumascape.com.au

RELAMPING

A CB

6

6

Isolate and Open Fixture

Ensure the fixture is electrically isolated.
Loosen the screws with the Allen Key
provided. If necessary gently lever lid out
with a large screwdriver.

Replace Lamp

Remove old lamp and check condition of
lampholder. Check new lamp WATTAGE,
VOLTAGE and TYPE. Insert new
lamp,(Refer installation instruction 4 over.)

7

Adjust, Aim, Test and Seal

If necessary, readjust and re-aim gimbal
position.
Test and seal fixture as per installation
Instructions through to , over.

68

8

LAMP SOURCE CONVERSION INSTRUCTION

1 32

Isolate and
Open Fixture

Ensure the fixture is electrically isolated.
Loosen the screws with the Allen Key
provided. If necessary gently lever lid out
with a large screwdriver.

Remove Gimbal

Remove gimbal by loosening the locking
screw and pulling vertically.

4 5

GUIDE
PINS

GIMBAL
LOCKING
SCREW

GEAR
ASSEMBLY

Remove Gear Assembly

Remove gear assembly by pulling vertically
(Note: Gear assembly may be screwed to
fixture body).

6

6

6

7

8

Insert New Gear Assembly

Align holes in gear tray with Threaded
Guide Pins in base of fixture and insert
fully, fit S/S nuts to retain

LUMASCAPE
HEAD OFFICE

T 07 3286 2299 F 07 3286 6599

Lumascape Lighting Industries 2006©

LUMASCAPE

SYDNEY - NSW

T 02 9519 6860 F 02 9519 8834

LUMASCAPE

MELBOURNE - VIC

T 03 9686 1900 F 03 9686 1700

Replace Lamp

Remove old lamp and check condition of
lampholder. Check new lamp WATTAGE,
VOLTAGE and TYPE. Insert new
lamp,(Refer installation instruction 4 over.)

www.lumascape.com.au

H.I. LIGHTING

LUMASCAPE AGENT - WA

T 08 9321 5422 F 08 9321 5881

LIGHTING PARTNERS AUSTRALIA

LUMASCAPE AGENT - SA

T 08 8232 0074 F 08 8232 0076

LUMASCAPE AGENT - NTH QLD

T 07 4031 4490 F 07 4031 5933

Adjust, Aim, Test and Seal

If necessary, readjust and re-aim gimbal
position.
Test and seal fixture as per installation
instructions through to , over.

NQ LIGHTING

68

ECC LIGHTING

LUMASCAPE AGENT - NZ

T 09 379 9680 F 09 308 9328

LUMASCAPE USA INC

Free Call 1-866-695-LUMA(5862)

T 1-(650)-595-LUMA(5862) 1-(650)-595-5820

C1613 - 2007_01_REV-003

Lumascape Lighting Industries Pty Ltd

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

LUMASCAPE AGENT - NZ

Tel [phone]

DISCONTINUED PRODUCT

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
Tel [phone] Fax [phone] Email [e-mail]

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT INFORMATION

C1721 - 2006_11_REV-002

WARNING - To reduce the risk of FIRE or INJURY:

Luminaires and transformers to be installed by qualifi ed installers only.

1.

Luminaires to be used for intended purpose only. e.g Wall Mount fi ttings must be wall mounted.

2.

Luminaires can become very hot. Use discretion in placement.

3.

Do not touch hot lens, guard, or enclosure.

4.

CAUTION - HOT SURFACE. Keep away from curtains and other combustible material.

5.

Turn Off/Unplug and allow to cool before replacing lamp.

6.

Keep lamp away from materials that may burn.

7.

Never touch lamp with bare fi ngers. Oil from skin may damage lamp. Hold lamp with soft cloth when installing or replacing.

8.

Do not operate the luminaires with a missing or damaged parts.

9.

Replace any cracked protective shield

10.

Use only lamp type, voltage and wattage as specifi ed by Lumascape on the product label.

11.

Use only genuine Lumascape parts to replace damaged or missing components.

12.

Luminaires supplied with Loctite Silver Grade Anti Seize lubricant on threads. Reapply if needed.

13.

Refer to instructions for installation and operating requirements.

14.

Ensure installation complies with local regulations

15.

SAVE THESE INSTRUCTIONS.

LUMASCAPE
HEAD OFFICE - QLD
Tel [phone]

Fax [phone]

LUMASCAPE

SYDNEY - NSW

Tel [phone]

Fax [phone]

LUMASCAPE

MELBOURNE - VIC

Tel [phone]

Fax [phone]

www.lumascape.com.au

LUMASCAPE USA INC.
SAN FRANCISCO - CA
Tel [phone]

Fax [phone]

H.I. LIGHTING

LUMASCAPE AGENT - WA

Tel [phone]

Fax [phone]

LIGHTING PARTNERS AUSTRALIA

LUMASCAPE AGENT - SA

Tel [phone]

Fax [phone]

Copyright ©2006 Lumascape Lighting Industries Pty. Ltd. ABN 21 010 572 773www.lumascape.com.au

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

Tel [phone]

Fax [phone]

ECC LIGHTING

LUMASCAPE AGENT - NZ

Tel [phone]

Fax [phone]