Lumascape LS333ANS-2COB, LS333AS-2COB Installation Instructions Manual

Warranty void if not installed as per installation instructions

INSTALLATION INSTRUCTIONS

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
PO Box 1875, Cleveland D.C., QLD 4163, Australia

T 07 3286 2299
F 07 3286 6599
E [e-mail]
W www.lumascape.com.au

IN0157 - 18 March 2016

Copyright ©2016 Lumascape Lighting Industries Pty. Ltd. ABN 21 010 572 773

www.lumascape.com.au

LS333ANS-2COB & LS333AS-2COB IP68

A.C.N. 0105 72 773

MODEL: LS333ANS-2COB & LS333AS-2COB

INSTRUCTIONS COVER: 30 V DC Ripple Free Power Supply

UNDERWATER

NOTE: These installation instructions are accepted in most areas. Some supply authorities may require alternative installation methods.
Should you experience any difficulty, please contact Lumascape directly: phone [phone] or email [e-mail]

IF IN DOUBT, PLEASE CALL

DANGER

ISOLATE LUMINAIRE FROM POWER

Failure to isolate power
supply before installation or
maintenance may result in
fire, serious injury, electric
shock, death and may
damage the luminaire.

WARNING

FINISHED

APPEARENCE

It is strongly recommended to use

Lumascape power supply or transformer

Use of electronic transformer will

permanently damage luminaire

All connections must be kept dry; failure to

do so may result in product reliability issues

Installation to be done by a qualified

electrician

1

2

3

4

5

6

7

A

1

Luminaire Cable

Connect to a suitable power supply in accordence
with local wiring rules.

2

Suppluy Conduit

Attach to niche gland and use to run luminaire
cable back to power supply.

3

Niche

Install at the time of construction. Use temporary
fibre board shield supplied to cover niche when
concrete is sprayed. About 1.3 m of cable can be
coiled inside the niche.

4

Mounting Lugs

Use to hold niche in place during construction.

5

Mounting Ring

Used slightly adjust luminaire position and rotation
within niche.

6

Luminaire

If your luminaire was ordered with the factory
pre-set tilted optical system make sure to install it
in the correct orientation.

7

Cover Plate

Place in front of luminaire before using screws to
mount luminaire and cover plate to mounting ring.

A

Diffuser Installation

Open luminaire and insert diffuser between
reflector and accessory holder. Re-seal
luminaire.

Single Colour Dim

Wire Colour Designation

Black 30 V DC

-

Red 30 V DC +

Grey

(1)

PWM

(1)

Do not connect if dimming

is not required

NOTE: Make sure to pull luminaire cable
through mounting ring before feeding
through conduit and terminating

IN0157 - 18 March 2016

Copyright ©2016 Lumascape Lighting Industries Pty. Ltd. ABN 21 010 572 773

www.lumascape.com.au

WARNING - To reduce the risk of FIRE or INJURY:

1. Luminaires and transformers to be installed by licensed electrical contractors.

2. Luminaires to be used for intended purpose only.

3. Do not operate the luminaires with a missing or damaged parts.

4. Use only genuine Lumascape parts to replace damaged or missing components.

5. Refer to instructions for installation and operating requirements.

6. Ensure installation complies with local regulations

Voltage insulation test (megger) will permanently damage product and will void warranty.

SAVE THESE INSTRUCTIONS.

SAFETY INSTRUCTIONS

Questions?

Call [phone]

Email [e-mail]

www.lumascape.com.au

u Take the round 18/2 gauge cable end and feed first through conduit

from the transformer end. DO NOT feed from Niche end because the
factory cable join of the figure eight low voltage cable and the 18/2
cable will not go through the gland in the bottom of the Niche.

Feed cable into niche, allowing sufficient free cable in niche to allow
the fitting to be placed on the poolside for re-lamping. Figure 1

NB: A maximum of 1.3m of cable can be coiled
inside the niche.

Firmly tighten cable gland on the inside of niche to seal cable
entry. Figure 2

1

FEED CABLE THROUGH

CONDUIT INTO NICHE

2

Connect cable to fixture

1. Take the round 18/2 guage cable end and trim insulation back
according to Figure 3.

100mm

8mm

FIGURE 3

Strip cable as specified above before connecting to fixture.

FIGURE 4

Feed stripped cable
end through gland
and into fixture

2. Feed stripped end of cable through fixture cable gland.

3. Terminate stripped wires into terminal block as shown in Figure 5.
Ensure Thermal Cutout remains in correct position.

Figure 5

Tighten external cable gland nuts so that they are firmly touching.

As an extra precautionary measure to ensure no moisture
comes up through the cable into the fixture, please place a
suitable neutral cure silicone around the top of the gland totally
covering the end of the cable.

FIGURE 1

ROUND CABLE END

NICHE

CONDUIT

ANTI-LEACH
CONNECTION

FIGURE EIGHT
LOW VOLTAGE
CABLE

FIGURE 2

Gland

Tighten cable gland firmly
to ensure good seal on cable.

A

START

HERE

IMPORTANT INSTRUCTIONS

MODELS LS682-0310, LS682-0620,

LS682-0625, LS682-1030
12V 75watt max.
lamp IP68 rated

A.C.N. 010 572 773

Lumascape Lighting Industries 2006©

LUMASCAPE
HEAD OFFICE

T 07 3286 2299 F 07 3286 6599

LUMASCAPE

SYDNEY - NSW

T 02 9519 6860 F 02 9519 8834

LUMASCAPE

MELBOURNE - VIC

T 03 9686 1900 F 03 9686 1700

ECC LIGHTING

LUMASCAPE AGENT - NZ

T 09 379 9680 F 09 308 9328

H.I. LIGHTING

LUMASCAPE AGENT - WA

T 08 9321 5422 F 08 9321 5881

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

T 07 4031 4490 F 07 4031 5933

LIGHTING PARTNERSAUSTRALIA

LUMASCAPE AGENT - SA

T 08 8232 0074 F 08 8232 0076

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
PO Box 1875, Cleveland D.C., QLD 4163, Australia
T 07 3286 2299
F 07 3286 6599
E [e-mail]
W www.lumascape.com.au

Warning: The Luminaire should only be used complete with its protective shield (cover)

For Installation of fitting LS682 cable extensions

C1045 - 2006_11_REV-001

TERMINAL BLOCK

THERMAL CUTOUT

TERMINAL BLOCK
MOUNTING BRACKET

TO LAMPHOLDER

FIGURE 5

Inject here with Neutral cure
silicone.

Tighten cable gland so that both
nuts are touching.

TOP VIEW

T 1-(650)-595-LUMA(5862) 1-(650)-595-5820

LUMASCAPE USA INC

Free Call 1-866-695-LUMA(5862)

www.lumascape.com.au

www.lumascape.com.au

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
Tel [phone] Fax [phone] Email [e-mail]

LUMASCAPE

HEAD OFFICE - QLD

Tel [phone]

Fax [phone]

LUMASCAPE

SYDNEY - NSW

Tel [phone]

Fax [phone]

LUMASCAPE

MELBOURNE - VIC

Tel [phone]

Fax [phone]

LUMASCAPE USA INC.
SAN FRANCISCO - CA
Tel [phone]
Fax [phone]

H.I. LIGHTING

LUMASCAPE AGENT - WA

Tel [phone]

Fax [phone]

LIGHTING PARTNERS AUSTRALIA

LUMASCAPE AGENT - SA

Tel [phone]

Fax [phone]

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

Tel [phone]

Fax [phone]

ECC LIGHTING

LUMASCAPE AGENT - NZ

Tel [phone]

Fax [phone]

Copyright ©2006 Lumascape Lighting Industries Pty. Ltd. ABN 21 010 572 773www.lumascape.com.au

IMPORTANT INFORMATION

WARNING - To reduce the risk of FIRE or INJURY:

Luminaires and transformers to be installed by qualifi ed installers only.

Luminaires to be used for intended purpose only. e.g Wall Mount fi ttings must be wall mounted.

Luminaires can become very hot. Use discretion in placement.

Do not touch hot lens, guard, or enclosure.

CAUTION - HOT SURFACE. Keep away from curtains and other combustible material.

Turn Off/Unplug and allow to cool before replacing lamp.

Keep lamp away from materials that may burn.

Never touch lamp with bare fi ngers. Oil from skin may damage lamp. Hold lamp with soft cloth when installing or replacing.

Do not operate the luminaires with a missing or damaged parts.

Replace any cracked protective shield

Use only lamp type, voltage and wattage as specifi ed by Lumascape on the product label.

Use only genuine Lumascape parts to replace damaged or missing components.

Luminaires supplied with Loctite Silver Grade Anti Seize lubricant on threads. Reapply if needed.

Refer to instructions for installation and operating requirements.

Ensure installation complies with local regulations

SAVE THESE INSTRUCTIONS.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

IMPORTANT SAFETY INSTRUCTIONS

C1721 - 2006_11_REV-002

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

LUMASCAPE AGENT - NZ

Tel [phone]

Lumascape Lighting Industries Pty Ltd

38-44 Enterprise Street, Cleveland, QLD 4163, Australia
Tel [phone] Fax [phone] Email [e-mail]

LUMASCAPE

HEAD OFFICE - QLD

Tel [phone]

Fax [phone]

LUMASCAPE

SYDNEY - NSW

Tel [phone]

Fax [phone]

LUMASCAPE

MELBOURNE - VIC

Tel [phone]

Fax [phone]

LUMASCAPE USA INC.
SAN FRANCISCO - CA
Tel [phone]
Fax [phone]

H.I. LIGHTING

LUMASCAPE AGENT - WA

Tel [phone]

Fax [phone]

LIGHTING PARTNERS AUSTRALIA

LUMASCAPE AGENT - SA

Tel [phone]

Fax [phone]

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

Tel [phone]

Fax [phone]

ECC LIGHTING

LUMASCAPE AGENT - NZ

Tel [phone]

Fax [phone]

Copyright ©2006 Lumascape Lighting Industries Pty. Ltd. ABN 21 010 572 773www.lumascape.com.au

VOLTAGEDROP

LOAD

WATTAGE

DROP CABLE TRUNK CABLE

3.3mm

2

LS604 6mm2 LS604-6 10mm2 LS604-10

SINGLE DOUBLE SINGLE DOUBLE SINGLE DOUBLE

20 70m 140m 105m 210m 140m 280m

40 30m 60m 55m 110m 84m 168m

50 25m 50m 44m 88m 62m 124m

60 20m 40m 36m 72m 54m 108m

70 15m 30m 30m 60m 50m 100m

80 14m 28m 27m 54m 46m 92m

90 13m 26m 24m 48m 42m 84m

100 12m 24m 21m 41m 36m 72m

120 10m 20m 18m 36m 30m 60m

150 7m 14m 15m 30m 26m 52m

200 5m 10m 11m 22m 20m 40m

250 4m 8m 9m 18m 17m 34m

CAUTION

The distances and wattages shown are maximum and should not be exceeded.

TRANSFORMER

20W

20m

Circuit 1

60m

Circuit 2

20W 20W 20W 20W

CABLE VOLTAGE DROP

Excessive voltage drop causes lamps to
have a low light output. The following
charts and illustrations apply only to
Lumascape supplied cable. The distance
and wattage shown are maximum and
should not be exceeded.

6mm2 Figure 8 PVC Cable

LS604-6

9.5mm

4.2mm

3.3mm2 Figure 8 PVC Cable

LS604

10mm2 Figure 8 PVC Cable

LS604-10

13.8mm

6.3mm

TABLE: VOLTAGE DROP

EXAMPLE 1

CABLES

EXAMPLE 2

20W

50m

Circuit 3

168m

Circuit 4

LS604-10 TRUNK CABLE

LS604 DROP CABLE

6m max

20W 20W 20W 20W

TRANSFORMER

12.5mm

5.4mm

EXAMPLE 2

Using trunk and drop cable only

This example shows the correct way to install
Lumascape luminaires using LS604-10
(10mm

2

) trunk cable. The total load on
Circuit 3 is 60W over 50 metres which is
shorter than the 54 metres allowed in the
Voltage Drop table. The load on Circuit 4 is
40W and using a doubled cable allows the
circuit to be up to 168 metres long.

EXAMPLE 1

Using drop cable only

This example shows the correct way to install
Lumascape light luminaires using LS604
(3.3mm

2

) drop cable. The total load on
Circuit 1 is 60W over 20 metres as allowed
in the Voltage Drop table. The load on Circuit
2 is 40W and by using a doubled cable this
circuit can be 60 metres.

NQ LIGHTING

LUMASCAPE AGENT - NTH QLD

LUMASCAPE AGENT - NZ

Tel [phone]