Lumascape LS3080, LS640-K?84, Erden E8 Installation Instructions Manual

Erden
INSTALLATION INSTRUCTIONS
E8
LS3080
USA I Australia I Asia I Middle East I Europe
LS3080 + LS640-K 84 Pre-Installation
N653
DANGER
ISOLATE LUMINAIRE FROM POWER
Failure to isolate power supply before installation or maintenance may result in fire, serious injury, electric shock, death and may damage the luminaire.
IP68
Warranty Void if not installed as per installation instructions and in compliance with the local electrical code.
READ ALL SAFETY INSTRUCTIONS FIRST
› Follow instructions carefully, failure to do so will void
warranty.
› Ensure installation complies with local law and
applicable standards. › Input voltage range 110-277V AC 50/60Hz. › Requires Lumascape PowerSync Master LS6540 for
dimming or color changing.
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
› Never make connections whilst the power is
connected.
› All connections must be kept dry; failure to do so
may result in product reliability issues. › Ensure mains input power is surge protected. › Do not make modifications or alter the product. › Keep luminaire clean and free of debris.
IN0167 181126 CE UL
1 / 7
Erden
torque order
E8
LS3080
General Assembly
To prevent condensation, ensure luminaire is acclimatized (at same temperature as environment) before installation.
Aiming Luminaire
B
INSTALLATION INSTRUCTIONS
Cover Screw(s)
Tighten in the following torque pattern to seal luminaire.
Luminaire Cover
After aiming luminaire at target seal luminaire using the cover.
Align the cover screws and the screw holes in the luminaire body with the corresponding threaded holes in the pre-installation kit.
Be sure to tighten cover screws as per the torque pattern shown above.
USA I Australia I Asia I Middle East I Europe
1
6
4
D
3
5
2
C
A
A
Aim Mark
Point in the direction of the target to be lit.,
B
Rotation Lock Screw
Tighten to lock gimbal rotation.
C
Tilt Adjustment Screw
Turn to adjust tilt of gimbal.
Temporary Cover
Keep on pre-instalation kit in order to avoid concrete and debris from entering the cavity. Remove when ready to installl luminaire.
Ensure all Sealing Surfaces are Clean
1
D
Luminaire Body
Slide into pre-installation kit and secure to mounting collar using cover and cover screws.
Luminaire Cable / Hookup Wire
Terminate in accordance to local wiring rules.
Make sure to properly isolate data wire if not used.
See diagram below for conductor colour and designation.
Mounting Collar
Ensure final installation surface is completely flush with top face of the blockout.
Mounting Brackets
Screw mounting brackets to collar to arrest any movement.
Gravel
Use gravel which allows good drainage around luminaire.
2
Ensure all sealing surfaces are clean and free of concrete, dirt, debris or any
3
other foreign matter. Sealing Surfaces include.
1
Entire Rubber Lid Seal
2
Luminaire Flange
3
Luminaire Lid Uderside
Poured Concrete
Foam Plug
Use as a temporary barrier when concrete is poured around pre-installation kit.
Remove before installing luminaire to allow for adequate drainage.
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
Wiring Details
CE Color Code UL / ETL Color Code Designation
Green / Yellow Green Earth / Ground
Brown
Blue
Black
* Data wire must be appropriately insulated if not connected.
Operating voltage on this wire is 24 V. Incorrect wiring will damage luminaire and void warranty. Do not Hi-Pot test.
Bootlace ferrules must be ued on all wires when connecting in terminal blocks.
Black Active / Live
White Neutral
Grey Data *
IN0167 181126 CE UL
L
N
2 / 7
Erden
E8
LS3080
Installation Preparation
WARNING
INSTALLATION INSTRUCTIONS
USA I Australia I Asia I Middle East I Europe
› The luminaire should only be used complete with its
protective shield (cover). › Keep electronics free from dirt and moisture. › Luminaires can become very hot. Use discretion in
placement. › No power tools to be used.
Component Overview
Connection Type ‘84’
› Do not shorten or interfere with cable assembly. › Warranty will be void if cable assembly is tampered
with. › Do not overtighten lid screws. › Do not apply downward force on the lid of luminaire.
Connection Type ‘82’
North American market only
Ø7.0”
(178 mm)
Ø10.3” (262 mm)
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
17.7” (450 mm)
19.4” (494 mm)
3 / 7
IN0167 181126 CE UL
Erden
To Lumascape luminaire
To next luminaire
From
PowerSync
TM
Master
Neutral - Blue Earth - Green / Yellow Data - Black Line - Brown
INSTALLATION INSTRUCTIONS
E8
LS3080
USA I Australia I Asia I Middle East I Europe
Network Topology
LS3080 Dimming
Junction box, or other approved
DMX In
110-240 V 50/60 Hz
110-240 V 50/60 Hz
Junction Box Junction Box Termination
When no data injector is in use (non-dimming applications), isolate data wire.
wiring device.
LS6540 PowerSync™ Data Injector
Loop to next PowerSync™
Data Injector
LS6540 PowerSync™ Data Injector
6’ (1.8 m) max
Australia | Asia | Middle East | Europe
Up to 45 luminaires per run Max run length 492 ft (150 m).
Consult voltage drop and run length tables for specific limitations.
To Lumascape luminaire
For last luminaire in the circuit, install terminating resistor in parallel across the data wire and earth wire.
Neutral - Blue Earth - Green / Yellow Data - Black Line - Brown
From
Master
TM
PowerSync
Trunk cable and junction box supplied by others Trunk cable and junction box supplied by others
LS3080 Non-Dimming
Junction box, or other approved wiring device.
max
6’ (1.8 m)
110-240 V 50/60 Hz
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
When no data injector is in use (non-dimming applications), isolate data wire.
3.3kΩ / 2W
Fit 3.3kΩ, 2 Watt terminator resistor (LS6406) between earth and data wires. Two LS6406 have been supplied with the LS6540 PowerSync master for this purpose.
TM
IN0167 181126 CE UL
4 / 7
Erden
INSTALLATION INSTRUCTIONS
E8
LS3080
USA I Australia I Asia I Middle East I Europe
Network Topology
LS3080 Dimming
Junction box, or other approved
DMX In
120-277 V 50/60 Hz
120-277 V 50/60 Hz
Junction Box Junction Box Termination
When no data injector is in use (non-dimming applications), isolate data wire.
wiring device.
LS6540 PowerSync™ Data Injector
Loop to next PowerSync™
Data Injector
LS6540 PowerSync™ Data Injector
To Lumascape luminaire
6’ (1.8 m) max
Neutral - White Earth - Green / Yellow Data - Grey Line - Black
Up to 45 luminaires per run Max run length 492 ft (150 m).
Consult voltage drop and run length tables for specific limitations.
Always observe NEC branch circuit current limitations.
To Lumascape luminaire
North America
For last luminaire in the circuit, install terminating resistor in parallel across the data wire and earth wire.
Neutral - White Earth - Green / Yellow Data - Grey Line - Black
From
Master
TM
PowerSync
Trunk cable supplied by others Trunk cable supplied by others
To next luminaire
From
PowerSync
Master
TM
LS3080 Non-Dimming
Junction box, or other approved wiring device.
6’ (1.8 m) max
When no data injector is in use (non-dimming applications), isolate data wire.
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
3.3kΩ / 2W
Fit 3.3kΩ, 2 Watt terminator resistor (LS6406) between earth and data wires. Two LS6406 have been supplied with the LS6540 PowerSync master for this purpose.
Observe NEC branch circuit current limitations.
TM
5 / 7
IN0167 181126 CE UL
Erden
gravel
hole
10.3” Ø262mm
finished surface
19.4” (494mm)
INSTALLATION INSTRUCTIONS
E8
LS3080
USA I Australia I Asia I Middle East I Europe
Installation
Step 1
Layout luminaire locations as required. Use discretion in placement as luminaire may become hot and could burn. Luminaire cavity should be as shown. Ensure gravel or similar medium forms the bottom of the cavity to allow drainage.
Note: Always check luminaire lable for correct supply details and lamp type if applicable.
Step 2
Position and use screws to attach brackets at the bottom of the mounting collar before concrete is poured.
IP68
Step 3
Fit sleeve, collar and cover plate.
Fit sleeve and collar over foam plug.
Ensure enough cable is in the cavity to connect to luminaire.
Position top surface of the mounting collar to be flush with final surface level.
Screw cover plate to mounting collar.
Ensure ample depth for fitting.
Step 5 Step 6Step 4
Pour concrete. Check that the top surface of the mounting collar is flush with the finished surface level.
Finished Surface Level
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
When ready to install luminaire;
Destroy foam plug and assemble luminaire.
Remove cover plate, glass and seal.
Minimum length of cable protruding from the ground to be 100mm.
Factory supplied
anti-leach cable
Connect cable / hookup wire in accordance with local wiring rules.
IMPORTANT: Power supply must be isolated prior to connection or disconnection of cables. Failure to do so will result in damage to the luminaire components.
6 / 7
IN0167 181126 CE UL
Erden
360°
20°
360°
20°
360°
20°
Air gap
torque order
torque order
1
2
6
5
3
4
INSTALLATION INSTRUCTIONS
E8
LS3080
USA I Australia I Asia I Middle East I Europe
Installation cont...
Ensure that luminaire is acclimatized. Remove moisture sachet from packet supplied with lid assembly, remove gimbal from luminaire body and drop the sachet in the base of luminaire body.
To prevent condensation, ensure luminaire is acclimatized (at same temperature as environment) before installation. Do not remove sachet from sealed packaging at this stage.
Step 8Step 7
Rotate gimbal until Aiming Mark is targeted as desired.
Lock Gimbal. Whilst exerting downward pressure on gimbal, tighten rotational lock grub screw.
IP68
Step 9
Adjust gimbal tilt angle by rotating Tilt Adjust screw with Allen key supplied.
360°
20°
Step 10 Step 11
Lay lid partially over luminaire to allow a gap for any moisture present to evaporate prior to sealing. Connect to supply and allow to burn for 2 hours.
IMPORTANT: Do not energise without partially covering gimbal.
Alternatively, using heat gun set at 100°C, heat the inside of luminaire at a distance of 300mm away for 10 minutes.
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia Phone +61 7 3854 5000 | Fax +61 7 3854 5001 | Email: sales@lumascape.com.au | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA Phone +1 650 595 5862 | Fax +1 650 595 5820 | Email: info@lumascape.com | www.lumacape.com
Products and specifications are subject to change without notice.
2 hours
Seal immediately after de-energising. Ensure seal and sealing surface is clean. Clean glass if necessary. Tighten lid screws using the 3mm allen key supplied. Ensure seal/sealing surface is free from debris. Lumascape recommends tightening using the torque pattern below.
Do not overtighten screws, 3Nm max.
1
6
4
2
3
5
7 / 7
IN0167 181126 CE UL
Loading...