User Manual
Welcome to Lumapower
Please take a moment to register your product on our Web site at
http://www.Lumapower.com. It enables us to keep you posted on our latest advancements,
and helps us to better understand our customers and build products that meet their needs
and Expectations.
This product has been designed and manufactured to the highest quality standards. However ,
if something does go wrong with this product, Lumapower and its national distributors
warrant free of charge labour and replacement parts in any country served by an official
distributor.
MVP
Lumapower Innovative Flashlight
Unpacking: Check the product carefully. If it has been damaged in transit, report the
damage immediately by calling your dealer and/or the shipping company that delivered it.
Read Instructions. All the safety and operating instructions should be read before the
product is operated.
Follow Instructions. All operating and use instructions should be followed.
Replacement Parts. When replacement parts are required, be sure the replacement parts
have the same characteristics as the original part. Unauthorized substitutions may cause
damage to the unit.
Introduction
The Lumapower MVP supports input voltage from 6.5V to 10V. The MVP is fitted with pure
white LED module driven by a constant current regulation circuitry to achieve a consistent
level of light output for the useable life of the batteries. With Over discharge protection at
4.8V and current control protection to enhance battery life and safety. LumaPower only
recommends the use of PCB protected batteries.
Combination Battery Type Pcs
1 Rechargeable 18650 (3.7V)
2
2 Rechargeable 17670 (3.7V)
2
3 Rechargeable 17650 (3.7V)
2
4 Rechargeable 16340 (3.7V)
2
(5) (Primary 123A (3.0V)
**SEE NOTE**
(4)
WARNING: Primary CR123A batteries are not intended to be a primary
battery source for the MVP and should only be used for
backup/emergencies. The 12V output of 4 primary CR123A’s and their
increasing resistance due to the high current load of the MVP means they
they can damage the light or become over-heated. As the current demand
is only problematic on the high output setting primary CR123A batteries
can be used with the light on the LOW and MEDIUM settings safely but if
used on the HIGH setting runtimes must be kept under 4 minutes or
damage will occur. LumaPower will not warrant lights that have failed due
to failure to follow these directions.
The MVP features a forward clicky switch and multi-l evel SideKick control circuit with memory
functions.
Half-press the tail switch to power on MVP momentary, full press to lock it for constant on.
Cycle press the SideKick to select output mode.
Convertible Design
The MVP can be operate with 2x16340 , (with Secondary battery tube removed).
Reflectors/LED engine module can be easily upgrade.
Lanyard ring is removable.
SideKick output control and Memory
Press to cycle the output from High, Medium and Low and High-speed Tactical Strobe.
The SideKick module works on Power ON or OFF which remains the selected output with your
next start.
Battery Installation
Unscrew the tail or battery tube and insert new batteries with positive (+) ends towards LED
assembly. Restore hand tighten. Depress tail cap pushbutton switch to test.
Note: Flashlight will not light if batteries are inserted in the wrong direction.
Damage may occur with reversed battery polarity.
CAUTION: MVP flashlights are high-output lighting devices. Due to possible eye
injury, DO NOT look directly into the reflector when the light is switched on. Do not
shine the MVP into the eyes of others. Safety is your responsibility. External surface
temperature will rise during prolonged operation; this is a normal operating phenomenon.
Battery Replacement
If there is significant decrease in brightness of light output you should replace the batteries
with freshly charged batteries. Unscrew the LED-engine and remove the old battery. Insert
a new battery as mentioned in Battery Installation Guide
WARNING: Lithium batteries can expl ode or cause burns if disassembl ed, shorted,
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries i n a
pocket, purse or other container containing metal objects or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and
regulations for disposal.
Never use mixed-battery types or brands. Do not mix charged and uncharged
batteries. Input voltage limited to 10V, never use 4 x 16340 which may cause
circuit damage. Only use 4x CR123A on low or medium for emergencies. Power ON
MVP at High-out position unattended over 30 minutes may cause overheating and
damage.
Maintenance
Clean and lubricate threads with a clean cloth and apply thin coat of silicon-based lubricant to
rubber O-rings. Note: Do not use petroleum-based lubrication on O-rings. After prol onged
exposure to moisture, the bezel and batteries should be removed, inspected, and dried i f
necessary
.
WARNING: Lumapower reflectors are made with a highly precise process. Do not
touch or clean the reflecting surface using any cloth which may cause damage to the surface
material affecting the illuminating performance.
Innactive Periods.
If MVP is left unused for long period, the installed batteries should be removed from the unit.
Output & Runtime
Accurately specifying light output (lumens) and runtime is complicated for LED flashlights.
Installed batteries and operating temperature are the main factors affecting the light output
and runtime. Lumapower cannot guarantee its products can reach the specification under
the using condition of users.
Specification
LED : Cree XR-E Q5 x 3
Reflector : S MO type
Output : 50 Lumens to 700 Lumens
Runtime : 90 minutes at High, 2500 minutes at Low (2x18650 @2600mAH)
Input Voltage : 6.5V to 10V
Batteries : rechargeable Li-ion x 2 (16340,18650…)
Length : 236mm/171mm
Bezel Diameter : 60mm
Body Diameter : 28mm
Tail cap Diameter : 32mm
Reflector Diameter : 20mm
Weight : 383g (Full size without battery installed)
Material : T7 aircraft aluminum with Type III HA
Body color : Black
Accessories : spare o-rings (for battery tube)
Specifications: All product specifications/features are subject to change without no tification.
Loading...