User Manual
Welcome to Lumapower
Please take a moment to register your product on our Web site at
http://www.Lumapower.com. It enables us to keep you posted on our latest advancements,
and helps us to better understand our customers and build products that meet their needs
and Expectations.
This product has been designed and manufactured to the highest quality standards. However ,
if something does go wrong with this product, Lumapower and its national distributors
warrant free of charge labour and replacement parts in any country served by an official
distributor.
MVP
Lumapower Innovative Flashlight
Unpacking: Check the product carefully. If it has been damaged in transit, report the
damage immediately by calling your dealer and/or the shipping company that delivered it.
Read Instructions. All the safety and operating instructions should be read before the
product is operated.
Follow Instructions. All operating and use instructions should be followed.
Replacement Parts. When replacement parts are required, be sure the replacement parts
have the same characteristics as the original part. Unauthorized substitutions may cause
damage to the unit.
Introduction
Lumapower MVP supports input voltage from 6.5V to 10V. MVP is fitted with pure white LED
module driven by curre nt re gula tion c irc uitry to ach ieve a co nsist ent le vel of lig ht ou tput for
the useable life of the batteries. With Over discharge protection at 4.8V and current control
protection to enhance battery life
Combination Battery Type Pcs
1 Rechargeable 16340 (3.7V)
2
2 Rechargeable 17650 (3.7V)
2
3 Rechargeable 17670 (3.7V)
2
4 Rechargeable 18650 (3.7V)
2
MVP features a forward clicky switch and multi-level SideKick control circuit with memory
functions.
Half-press the tail switch to power on MVP momentary, full press to lock it for constant on.
Cycle press the SideKick to select output mode.
Convertible Design
MVP can be operate with 2x16340 , (with Secondary battery tube removed).
Reflectors/LED engine module can be easily upgrade.
Lanyard ring is removable.
SideKick output control and Memory
Press to cycle the output from High, Medium and Low and High-speed Tactical Strobe.
SideKick module works on Power ON or OFF which remains the selected output with your next
start.
Battery Installation
Unscrew the tail or battery tube and insert new batteries with positive ends towards LED
assembly. Restore hand tighten. Depress tail cap pushbutton switch to test.
Note: It would not light if battery is inserted in wrong direction.
Damage will occur with wrong battery insertion.
CAUTION: MVP flashlights are high-output lighting devices. Due to possible eye
injury, DO NOT look directly into the reflector when the light is switched on. Safety is
your responsibility, too.
External surface temperature will rise during prolonged operation; this is a normal operating
phenomenon.
Battery Replacement
If there is significant decrease in brightness of light output you should replace the battery.
Unscrew the LED-engine and remove the old battery. Insert a new battery as mentioned in
Battery Installation Guide
WARNING: Lithium batteries can expl ode or cause burns if disassembl ed, shorted,
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries i n a
pocket, purse or other container containing metal objects or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and
regulations for disposal.
Never use mixed-battery type. Replace all battery with the same kind.
Input voltage limited to 10V, never use 4x CR123A or 4 x 16340 which may cause circuit
damage.
Power ON MVP at High-out position unattended over 30 minutes may cause Overheat.
Maintenance
Clean and lubricate threads with a clean cloth and apply thin coat of silicon-based lubricant to
rubber O-rings. Note: Do not use petroleum-based lubrication on O-rings. After prol onged
exposure to moisture, the bezel and batteries should be removed, inspected, and dried i f
necessary
.
WARNING: Lumapower reflector is made with high precision process. Do not touch
or clean the reflecting surface using any cloth which may cause damage to the surface
material affecting the illuminating performance.
Non-use Periods.
If MVP is left unused for long period, the installed battery should be removed from the unit.
Output & Runtime
Accurately specifying light output (lumens) and runtime is complicated for LED flashlights.
Installed batteries and operating temperature are the main factors affecting the light output
and runtime. Lumapower doesn’t guarantee its products can reach the specification under the
using condition of users.
Specification
LED : Cree XR-E Q5 x 3
Reflector : S MO type
Output : 50 Lumens to 700 Lumens
Runtime : 90 minutes at High, 2500 minutes at Low (2x18650 @2600mAH)
Input Voltage : 6.5V to 12.5V
Batteries : rechargeable Li-ion x 2 (16340,18650…)
Length : 236mm/171mm
Bezel Diameter : 60mm
Body Diameter : 28mm
Tail cap Diameter : 32mm
Reflector Diameter : 20mm
Weight : 383g (Full size without battery installed)
Material : T7 aircraft aluminum with Type III HA
Body color : Black
Accessories : spare o-rings (for battery tube)
Specifications: All product specifications/features are subject to change without no tification.
Loading...