Lucent Technologies Inc T8207-BAL-DB, T8207-BAL-DT Datasheet

Download

Advance Data Sheet

September 2001

CelXpres

™ T8207

ATM Interconnect

1 Product Overview

1.1 Features

■ > OC-3 transport capability

■ UTOPIA level 1 and 2 (8-bit) cell-level handshake

interface (ATM or PHY layers)

■ 32 multi-PHY (MPHY) operation

■ Shared UTOPIA mode

■ Egress SDRAM buffer support to expand UTOPIA

output priority queues for 32K to 512K cells:

— 64 queues configurable up to four queues per

PHY with programmable size s

— Programmable number of UTOPIA output

queues with four levels of priority

■ Support of ATM traffic management via partial

packet discard (PPD), forward explicit congestion notification (FECN), and the cell loss priority (CLP) bit

■ Programmable slew rate GTL+ I/O:

— 1.7 Gbits/s cell bus operation — Programmable as bus arbiter

■ Flexible per port cell counters

■ Cell header translation and insertion with virtual

path identifier (VPI) and virtual channel identifier (VCI) via external SRAM (up to 64K entries)

■ Support of network node interface (NNI) and user

network interface (UNI) header types with optional generic flow control (GFC) insertion

■ Programmable operations and maintenance and

resource management (OAM/RM) cell routing

■ Support of multicast and broadcast cells per PHY

■ Programmable priority for control/data cells trans-

mission onto cell bus

■ Eight GPIO pins

■ JTAG support

■ Optional monitoring of misrouted cells

■ Microprocessor interface, supporting both

Motor-

ola

and

Intel

modes (multiplexed and nonmulti-

plexed)

■ Control cell transmission and re ception through

microprocessor port

■ Single 3.3 V power supply

■ 3.3 V TTL I/O (5 V tolerant)

■ 272-pin PBGA package

■ Industrial temperature range (–40 °C to +85 °C)

■ Hot insertion capability

■ Compatible with

Transwitch CellBus

1.2 Applications

■ Asymmetric digital subscriber line (ADSL) digital

subscriber line access multiplexer (DSLAMs)

■ Access gateways

■ Access multiplexers/concentrators

■ Multiservice access equipment platforms

2 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents

Contents Page

1 Product Overview................................................................................................................................................1

1.1 Features....................................................................................................................................................1

1.2 Applications...............................................................................................................................................1

1.3 Description ................................................................................................................................................8

1.4 Conventions ............................................................................................................................................11

1.5 Glossary..................................................................................................................................................12

2 Pin Description..................................................................................................................................................13

3 Powerup/Reset Sequence ................................................................................................................................20

4 Hot Insertion.... ....... ............................................. ...... ....... ...... ....... ...... ...... ....... ....................................... ...... ....21

5 PLL Configuration .............................................................................................................................................22

6 Microprocessor Interface ..................................................................................................................................23

6.1 Microprocessor Interface Configuration ..................................................................................................23

6.2 Microprocessor Interrupts........................................................................................................................23

6.3 Accessing the

CelXpres

T8207 via Microprocessor Interface.................................................................23

6.3.1 Accessing the Extended Memory Registers...............................................................................24

6.3.1.1 Extended Memory Writes.............................................................................................24

6.3.1.2 Extended Memory Reads.............................................................................................24

6.3.2

CelXpres

T8207 Access Performance .......................................................................................25

7 General-Purpose I/O (GPIO) ............................................................................................................................26

8 Look-Up Table ..................................................................................................................................................27

8.1 Look-Up Table RAM................................................................................................................................27

8.2 Organization............................................................................................................................................28

8.3 Look-Up Procedure .................................................................................................................................33

8.4 Extended Records...................................................................................................................................36

8.5 Diagnostics..............................................................................................................................................41

8.6 Setup.......................................................................................................................................................41

9 UTOPIA Interface..............................................................................................................................................42

9.1 Incoming UTOPIA Cell Interface.............................................................................................................43

9.1.1 Incoming PHY Mode (Cells Received by T8207).......................................................................43

9.1.2 Incoming ATM Mode (Cells Received by T8207).......................................................................43

9.2 Outgoing UTOPIA Cell Interface.............................................................................................................44

9.2.1 Outgoing PHY Mode (Cells Sent by T8207)...............................................................................44

9.2.2 Outgoing ATM Mode (Cells Sent by T8207) ..............................................................................45

9.3 Counters..................................................................................................................................................46

9.4 55-Byte UTOPIA Mode............................................................................................................................47

9.5 Shared UTOPIA Mode ............................................................................................................................48

9.6 UTOPIA Pin Modes.................................................................................................................................50

9.7 UTOPIA Clocking ....................................................................................................................................53

10 Cell Bus Interface..............................................................................................................................................54

10.1 General Architecture ...............................................................................................................................54

10.2 Cell Bus Frames......................................................................................................................................56

10.3 Cell Bus Routing Headers.......................................................................................................................59

10.3.1 Control Cells...............................................................................................................................59

10.3.2 Data Cells...................................................................................................................................60

10.3.3 Loopback Cells...........................................................................................................................60

10.3.4 Multicast Routing............. ...... ....... ...... ....... ...... ............................................. ....... ...... ....... ...... ....60

10.3.5 Broadcast Routing......................................................................................................................61

10.4 Cell Bus Arbitration..................................................................................................................................61

10.5 Cell Bus Monitoring .................................................................................................................................62

10.6 GTL+ Logic... ...... ...... ....... ...... .............................................. ...... ...... ....... ...... ....... ...... . ...... ...... ....... ...... ....62

10.7 Cell Bus Write and Read Clocks.............................................................................................................63

Agere Systems Inc. 3

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents (continued)

Contents Page

11 SDRAM Interface..............................................................................................................................................64

11.1 Memory Configuration.............................................................................................................................64

11.2 Powerup Sequence.................................................................................................................................64

11.3 SDRAM Interface Timing ........................................................................................................................65

11.4 Queuing ..................................................................................................................................................66

11.5 SDRAM Refresh .....................................................................................................................................72

11.6 SDRAM Throughput................................................................................................................................73

12 Traffic Management.................. ...... ....... ...... ....... ...... ....... ...... ...... ....... ...... ....................................... ....... ...... ....74

12.1 Cell Loss Priority (CLP)...........................................................................................................................74

12.2 Forward Explicit Congestion Notification (FECN) ...................................................................................74

12.3 Partial Packet Discard (PPD)..................................................................................................................74

13 JTAG Test Access Port ....................................................................................................................................75

13.1 Instruction Register......................................... ....... ...... ...... ....... ...... ....... ...... ...........................................75

13.2 Boundary-Scan Register.........................................................................................................................76

14 Registers...........................................................................................................................................................79

14.1 Register Types........................................................................................................................................79

14.2 Direct Memory Access Registers............................................................................................................82

14.2.1 Little-Endian Format (big_end = 0) for Extended Memory Access

Registers 30h—37h ...................................................................................................................86

14.2.2 Big-Endian Format (big_end = 1) for Extended Memory Access

Registers 30h—37h ...................................................................................................................88

14.2.3 General-Purpose I/O Control Registers.....................................................................................90

14.2.4 Control Cells ..............................................................................................................................91

14.2.5 Multicast Memories ....................................................................................................................92

14.3 Extended Memory Registers...................................................................................................................93

14.3.1 Main Registers...........................................................................................................................93

14.3.2 UTOPIA Registers ...................................................................................................................106

14.3.2.1 TX UTOPIA Configuration .........................................................................................108

14.3.2.2 TX UTOPIA Monitoring..............................................................................................125

14.3.2.3 RX UTOPIA Monitoring..............................................................................................126

14.3.3 SDRAM Registers....................................................................................................................128

14.3.3.1 SDRAM Control Memory ...........................................................................................135

14.3.4 Various Internal Memories .............................. ...... ....... ...... ....... ...... ....... ...... ............................1 37

14.3.4.1 Control Cell Memories ...............................................................................................137

14.3.4.2 Multicast Number Memories ......................................................................................138

14.3.4.3 PPD State Memory.............................................. ....... ...... ....... ...... ....... ...... ...............140

14.3.5 External Memories...................................................................................................................141

14.3.5.1 Look-Up Translation Memory ....................................................................................141

14.3.5.2 SDRAM Buffer Memory .............................................................................................141

15 Absolute Maximum Ratings............................................................................................................................142

16 Recommended Operating Conditions.............................................................................................................142

17 Handling Precautions......................................................................................................................................142

18 Electrical Requirements and Characteristics..................................................................................................143

18.1 Crystal Information................................................................................................................................143

18.2 dc Electrical Characteristics..................................................................................................................144

19 Timing Requirements......................................................................................................................................145

19.1 Microprocessor Interface Timing...........................................................................................................146

19.2 UTOPIA Timing.....................................................................................................................................152

19.3 External LUT Memory Timing ...............................................................................................................153

19.4 Cell Bus Timing.....................................................................................................................................155

19.5 SDRAM Interface Timing ......................................................................................................................156

20 Outline Diagram..............................................................................................................................................157

21 Ordering Information.......................................................................................................................................158

4 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents (continued)

Figure Page

Figure 1. Functional Block Diagram ......................................................................................................................... 9

Figure 2. Dual Bus Implementation .............. ...... ....... ...... ....... ............................................. ...... ............................. 10

Figure 3. 272-Pin PBGA—Top View ...................................................................................................................... 19

Figure 4. Translation RAM Memory Map—8-Byte Records, for Up to 16 Ports..................................................... 29

Figure 5. Translation RAM Memory Map—8-Byte Records, for Greater than 16 Ports...........................................30

Figure 6. Translation Record Types—8-Byte Records........................................................................................... 31

Figure 7. Translation RAM Flow Diagram .............................................................................................................. 35

Figure 8. Translation Record Types—Extended Mode .......................................................................................... 37

Figure 9. Translation RAM Memory Map—Extended Mode, for Up to 16 Ports..................................................... 38

Figure 10. Translation RAM Memory Map—Extended Mode, for Greater than 16 Ports........................................39

Figure 11. Queue Priority Multiplexing ................................................................................................................... 46

Figure 12. TX UTOPIA Cell Handling..................................................................................................................... 47

Figure 13. TX UTOPIA Bus Sharing....................................................................................................................... 49

Figure 14. Cell Bus Frame Format (Bit Positions for 16 User Mode)..................................................................... 56

Figure 15. Cell Bus Frame Format (Bit Positions for 32 User Mode)..................................................................... 57

Figure 16. Cell Bus Routing Headers..................................................................................................................... 59

Figure 17. GTL+ External Circuitry......................................................................................................................... 62

Figure 18. SDRAM Timing Parameters.................................................................................................................. 65

Figure 19. Crystal ................................................................................................................................................. 143

Figure 20. Negative Resistance Plot.................................................................................................................... 143

Figure 21. Nonmultiplexed

Intel

Mode Write Access Timing................................................................................ 146

Figure 22. Nonmultiplexed

Intel

Mode Read Access Timing................................................................................ 146

Figure 23.

Motorola

Mode Write Access Timing................................................................................................... 148

Figure 24.

Motorola

Mode Read Access Timing .................................................................................................. 148

Figure 25. Multiplexed

Intel

Mode Write Access Timing....................................................................................... 150

Figure 26. Multiplexed

Intel

Mode Read Access Timing ...................................................................................... 150

Figure 27. External LUT Memory Read Timing (cyc_per_acc = 2 and cyc_per_acc = 3).................................... 153

Figure 28. External LUT Memory Write Timing (cyc_per_acc = 2 and cyc_per_acc = 3) .................................... 153

Figure 29. Cell Bus Timing ................................................................................................................................... 155

Figure 30. SDRAM Interface Timing..................................................................................................................... 156

Agere Systems Inc. 5

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents (continued)

Table Page

Table 1. UTOPIA Pins ........................................................................................................................................... 13

Table 2. Cell Bus Pins ........................................................................................................................................... 14

Table 3. SDRAM Interface Pins ............................................................................................................................ 15

Table 4. Microprocessor Interface Pins ....................................... ...... ....... ...... ....... ...... ....... ...... ............................. 16

Table 5. Translation SRAM Interface..................................................................................................................... 17

Table 6. JTAG Pins ............................................................................................................................................... 17

Table 7. General-Purpose Pins ............ ....... ...... ....... ...... ....... ...... ...... ....... ...... ....... ................................................ 18

Table 8. Power Pins .............................................................................................................................................. 18

Table 9. Loop Filter Register Settings.................................................................................................................... 22

Table 10. Access Times ................. ...... ............................................. ....... ...... ....... ...... ....... ... ................................ 25

Table 11. Active and Ignore Truth Table .................. ...... ....... ............................................. ...... ..... ........................ 31

Table 12. VPI Value Truth Table ....................... ....... ...... ....... ...... ............................................. . ............................ 32

Table 13. OAM Routing Control Truth Table ..... ....... ...... ....... ...... ...... .............................................. ...................... 32

Table 14. F5 Translation Record Addresses Table—8-Byte Records ................................................................... 33

Table 15. F5 Translation Record Addresses Table—Extended Mode................................................................... 40

Table 16. Port Numbering for MPHY Configurations ............................................................................................ 51

Table 17. Supported Memory Configurations ....................... ...... ............................................. ....... .... .................. 64

Table 18. Queue Organization and Port Group Address/Priority Bits for 16 Ports with T8207_sel = 1 .................67

Table 19. Queue Organization and Port Group Address/Priority Bits for 32 Ports ................................................ 69

Table 20. Queue Organization and Port Group Address/Priority Bits for 16 Ports with T8207_sel = 0...................71

Table 21. Instruction Register .............. ....... ...... ....... ...... ....... ...... ........................................... ............................... 75

Table 22. Boundary-Scan Register Descriptions ..... ...... ....... ...... ............................................. ....... ..... ................. 76

Table 23. Register Map................... ............................................. ...... ....... ...... ....... ...... ....... ................................ ....79

Table 24. Identification 0 (IDNT0) (00h) ................................................................................................................ 82

Table 25. Identification 1 (IDNT1) (01h)................................................................................................................. 82

Table 26. Identification 2 (IDNT2) (02h) ................................................................................................................ 82

Table 27. Direct Configuration/Control Register (DCCR) (28h) ............................................................................. 83

Table 28. Interrupt Service Request (ISREQ) (29h) ............................................................................................. 84

Table 29. mclk PLL Configuration 0 (MPLLCF0) (2Ah) .................................. ....... ................................................ 84

Table 30. mclk PLL Configuration 1 (MPLLCF1) (2Bh) .................................. ....... ................................................ 85

Table 31. GTL+ Slew Rate Configuration (GTLSRCF) (2Eh) ................................................................................ 85

Table 32. GTL+ Control (GTLCNTRL) (2Fh)...........................................................................................................85

Table 33. Extended Memory Address 1 (Little Endian) (EMA1_L E) (30h)................... ....... ...... ....... ...... ................ 86

Table 34. Extended Memory Address 2 (Little Endian) (EMA2_L E) (31h)................... ....... ...... ....... ...... ................ 86

Table 35. Extended Memory Address 3 (Little Endian) (EMA3_L E) (32h)................... ....... ...... ....... ...... ................ 86

Table 36. Extended Memory Address 4 (Little Endian) (EMA4_L E) (33h)................... ....... ...... ....... ...... ................ 86

Table 37. Extended Memory Access (Little Endian) (EMA_LE) (34h) ................................................................... 86

Table 38. Extended Memory Data Low (Little Endian) (EMDL_LE ) (36h) ............. ............................................. ... 87

Table 39. Extended Memory Data High (Little Endian) (EMDH_LE) (37h)............................................................ 87

Table 40. Extended Memory Address 4 (Big Endian) (EMA4_BE) (30h)............................................................... 88

Table 41. Extended Memory Address 3 (Big Endian) (EMA3_BE) (31h)............................................................... 88

Table 42. Extended Memory Address 2 (Big Endian) (EMA2_BE) (32h)............................................................... 88

Table 43. Extended Memory Address 1 (Big Endian) (EMA1_BE) (33h)............................................................... 88

Table 44. Extended Memory Access (Big Endian) (EMA _B E) (34h) . ....... ...... ....... ...... ....... ...... ....... ...................... 89

Table 45. Extended Memory Data High (Big Endian) (EMDH_BE) (36h) .................... ....... ...... ............................. 89

Table 46. Extended Memory Data Low (Big Endian) (EMDL_BE) (37h) ............................................................... 89

Table 47. GPIO Output Enable (GPIO_OE) (39h) .......... ....... ...... ...... ....... ...... ....... ...... ....... ...... ....... ...................... 90

Table 48. GPIO Output Value (GPIO_OV) (3Bh)................................................................................................... 90

6 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents (continued)

Table Page

Table 49. GPIO Input Value (GPIO_IV) (3Dh)........................................................................................................ 90

Table 50. Control Cell Receive Direct Memory (CCRXDM) (60h to 93h)............................................................... 91

Table 51. Control Cell Transmit Direct Memory (CCTXDM) (A0h to D7h) ............................................................. 91

Table 52. PHY Port 0 and Control Cells Multicast Direct Memory (PP0MDM) (E0h to FFh) ................................. 92

Table 53. Main Configuration 1 (MCF1) (0100h).................................................................................................... 93

Table 54. Main Interrupt Status 1 (MIS1) (0102h) ................................................................................................. 94

Table 55. Main Interrupt Enable 1 (MIE1) (0104h) ................................................................................................ 95

Table 56. TX UTOPIA Clock Configuration (TXUCCF) (010Ch) ............................................................................ 96

Table 57. RX UTOPIA Clock Configuration (RXUCCF) (010Eh)............................................................................ 97

Table 58. Main Configuration/Control (MCFCT) (0110h) ....................................................................................... 98

Table 59. Main Configuration 2 (MCF2) (0112h).................................................................................................... 98

Table 60. UTOPIA Configuration (UCF) (0114h) ................................................................................................. 100

Table 61. Main Configuration 3 (MCF3) (0116h) ................................................................................................. 100

Table 62. Loopback (LB) (0118h) ........................................................................................................................ 101

Table 63. UTOPIA Configuration 3 (UCF3) (011Ah)..............................................................................................101

Table 64. UTOPIA Configuration 2 (UCF2) (011Ch) ........................................................................................... 101

Table 65. Extended LUT Configuration (ELUTCF) (011Eh)................................................................................. 101

Table 66. Extended LUT Control (ELUTCN) (0120h) .......................................................................................... 102

Table 67. Cell Bus Configuration/Status (CBCFS) (0130h) ................................................................................. 103

Table 68. Main Interrupt Status 2 (MIS2) (0132h)................................................................................................ 103

Table 69. Main Interrupt Enable 2 (MIE2) (0134h)............................................................................................... 104

Table 70. Misrouted LUT 1 (MLUT1) (0142h) ..................................................................................................... 105

Table 71. Misrouted LUT 2 (MLUT2) (0144h) ..................................................................................................... 105

Table 72. Misrouted Cell Header High (MCHH) (0146h) ..................................................................................... 105

Table 73. Misrouted Cell Header Low (MCHL) (0148h) ...................................................................................... 105

Table 74. HEC Interrupt Status 1 (HIS1) (0302h)..................................................................................................106

Table 75. HEC Interrupt Enable 1 (HIE1) (0304h).................................................................................................106

Table 76. HEC Interrupt Status (HIS) (0306h) ..................................................................................................... 106

Table 77. HEC Interrupt Enable (HIE) (0308h) .................................................................................................... 106

Table 78. LUT Interrupt Service Request (LUTISR) (030Eh) .............................................................................. 106

Table 79. LUT X Configuration/Status (LUTXCFS) (0320h to 033Eh)................................................................. 107

Table 80. Master Queue 3 (MQ3) (0158h).............................................................................................................108

Table 81. Master Queue 2 (MQ2) (015Ah)............................................................................................................108

Table 82. Master Queue 0 (MQ0) (015Ch)........................................................................................................... 109

Table 83. Master Queue 1 (MQ1) (015Eh) .......................................................................................................... 109

Table 84. Slave Queue 0 (SQ0) (016Ch) ............................................................................................................ 110

Table 85. Slave Queue 1 (SQ1) (016Eh) ............................................................................................................ 110

Table 86. TX PHY FIFO Routing 3 (TXPFR3) (0178h).......................................................................................... 111

Table 87. TX PHY FIFO Routing 2 (TXPFR2) (017Ah) .........................................................................................112

Table 88. TX PHY FIFO Routing 0 (TXPFR0) (017Ch)........................................................................................ 113

Table 89. TX PHY FIFO Routing 1 (TXPFR1) (017Eh) ....................................................................................... 114

Table 90. Routing Information 1 (RI1) (0200h) .................................................................................................... 115

Table 91. Routing Information 2 (RI2) (0202h) .................................................................................................... 116

Table 92. Routing Information 3 (RI3) (0204h) .................................................................................................... 117

Table 93. PPD Information 1 (PPDI1) (0206h) .................................................................................................... 118

Table 94. PPD Information 2 (PPDI2) (0208h) .................................................................................................... 119

Table 95. PPD Information 3 (PPDI3) (020Ah)..................................................................................................... 120

Table 96. PPD Information 4 (PPDI4) (020Ch) ................................................................................................... 121

Table 97. PPD Information 5 (PPDI5) (020Eh) .................................................................................................... 122

Table 98. PPD Information 6 (PPDI6) (0210h) .................................................................................................... 123

Table 99. PPD Information 7 (PPDI7) (0212h) .................................................................................................... 124

Agere Systems Inc. 7

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

Table of Contents (continued)

Table Page

Table 100. PPD Memory Write (PPDMW) (0418h) ............................................................................................. 124

Table 101. PHY Port X Transmit Count Structure (PPXTXCNT) (0600h to 067Ch)............................................ 125

Table 102. PHY Port X Receive Count Structure (PPXRXCNT) (0700h to 07F8h)............................................. 126

Table 103. LUT X Configuration 1 Structure (LUTXCF1) (0704h to 077Ch).........................................................127

Table 104. SDRAM Control (SCT) (0400h) ......................................................................................................... 128

Table 105. SDRAM Interrupt Status (SIS) (0402h) ............................................................................................. 128

Table 106. SDRAM Interrupt Enable (SIE) (0404h) ............................................................................................ 128

Table 107. SDRAM Configuration (SCF) (0408h) ............................................................................................... 129

Table 108. Refresh (RFRSH) (0410h) .................................. ...... ...... ....... ...... ....... ...... ....... ................................. 130

Table 109. Refresh Lateness (RFRSHL) (0412h) .................................................................... ....... .................... 130

Table 110. Idle State 1 (IS1) (0420h) .................................................................................................................. 130

Table 111. Idle State 2 (IS2) (0422h) .................................................................................................................. 130

Table 112. Manual Access State 1 (MAS1) (0424h) ........................................................................................... 131

Table 113. Manual Access State 2 (MAS2) (0426h) ........................................................................................... 131

Table 114. SDRAM Interrupt Service Request 4 (SISR4) (0438h)........................................................................132

Table 115. SDRAM Interrupt Service Request 3 (SISR3) (043Ah)........................................................................132

Table 116. SDRAM Interrupt Service Request 1 (SISR1) (043Ch) ..................................................................... 132

Table 117. SDRAM Interrupt Service Request 2 (SISR2) (043Eh) ..................................................................... 132

Table 118. Queue X (QX) (0440h to 04BEh) ....................................................................................................... 133

Table 119. Queue X Definition Structure (QXDEF) (2000h to 27E0h)................................................................. 135

Table 120. Control Cell Receive Extended Memory (CCRXEM) (0800h to 0832h)............................................. 137

Table 121. Control Cell Transmit Extended Memory (CCTXEM) (0900h to 0936h) ............................................ 137

Table 122. PHY Port 0 and Control Cells Multicast Extended Memory (PP0MEM) (0C00h to 0C1Eh)............... 138

Table 123. PHY Port X Multicast Memory (PPXMM) (0C20h to 0DE0h)............................................................. 139

Table 124. PPD Memory (PPDM) (1000h to 13FEh) .......................................................................................... 140

Table 125. Translation RAM Memory (TRAM) (100000h to 17FFFEh) ............................................................... 141

Table 126. SDRAM (SDRAM) (2000000h to 3FFFFFEh) ................................................................................... 141

Table 127. Maximum Rating Parameters and Values.......................................................................................... 142

Table 128. Recommended Operating Conditions................................................................................................ 142

Table 129. HBM ESD Threshold.......................................................................................................................... 142

Table 130. Crystal Specifications ........................................................................................................................ 143

Table 131. External Clock Requirements............................................................................................................. 143

Table 132. dc Electrical Characteristics .............................................................................................................. 144

Table 133. Input Clocks ...................................................................................................................................... 145

Table 134. Output Clocks .................................................................................................................................... 145

Table 135. Nonmultiplexed

Intel

Mode Write Access Timing .............................................................................. 147

Table 136. Nonmultiplexed

Intel

Mode Read Access Timing .............................................................................. 147

Table 137.

Motorola

Mode Write Access Timing ................................................................................................. 149

Table 138.

Motorola

Mode Read Access Timing ................................................................................................. 149

Table 139. Multiplexed

Intel

Mode Write Access Timing .................................................................................... 151

Table 140. Multiplexed

Intel

Mode Read Access Timing ..................................................................................... 151

Table 141. TX UTOPIA Timing (70 pF Load on Outputs) ................................................................................... 152

Table 142. RX UTOPIA Timing (70 pF Load on Outputs) ................................................................................... 152

Table 143. External LUT Memory Read Timing (cyc_per_acc = 2) .................................................................... 154

Table 144. External LUT Memory Read Timing (cyc_per_acc = 3) .................................................................... 154

Table 145. External LUT Memory Write Timing (cyc_per_acc = 2) .................................................................... 154

Table 146. External LUT Memory Write Timing (cyc_per_acc = 3) .................................................................... 154

Table 147. Cell Bus Timing ................................................................................................................................. 155

Table 148. SDRAM Interface Timing .................................................................................................................. 156

8 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

1 Product Overview (continued)

1.3 Description

The

CelXpres

T8207 device integrates all of the required functionality to transport ATM cells across a backplane architecture with high-speed cell traffic exceeding 1.5 Gbits/s to a maximum of 32 destinations. The management of multiple service categories and monitoring of performance on ATM and PHY interfaces is incorporated in the

device’s functionality. Traffic delivery to multi-PHYs (MPHYs) is managed through the UTOPIA interface. The T8207 device meets the ATM Forum’s universal test and operations PHY interface for ATM (UTOPIA) Level 1,

Version 2.01 and Level 2, Version 1.0 specifications for cell-level handshake and MPHY data path operation with rates up to 353 Mbits/s. The T8207 supports the required MPHY operation as described in Sections 4.1 and 4.2 of the ATM Forum’s Level 2 specification. The T8207 supports MPHY operation with one transmit cell available (TxCLAV) signal and one receive cell available (RxCLAV) signal for up to 16 PHY ports for an 8-bit UTOPIA 2 interface configuration. With two transmit cells available/enable (TxCLAV/enb*) pairs of signals and receive cells available/enable (RxCLAV/enb*) pairs of signals, 32 MPHYs can be supported. In addition to the required UTOPIA signals, the optional transmit parity (TxPRTY) and receive parity (RxPRTY) signals are provided.

The T8207 may be configured as an ATM or PHY level device providing cell routing between UTOPIA and a 32-bit wide cell bus. In addition to the 32 data signals, the bus has the following signals:

■ Read clock

■ Write clock

■ Frame sync

■ Acknowledge

ATM cells arriving from the UTOPIA interface may get VPI and VCI translation and routing information from a lookup table in external SRAM. An external synchronous dynamic random access memory (SDRAM) is used to extend the buffering for ATM cells destined for the UTOPIA interface. This external SDRAM may be partitioned into four or less independently sized queues per PHY for a configuration of 16 MPHYs and two queues per PHY or a programmable number of queues per PHY for a configuration of 32 MPHYs. The number of cells per queue per PHY is programmable. The four queues may be used to implement quality of service (QoS) using different priorities for each queue.

The

CelXpres

T8207 provides a shared UTOPIA mode, which allows two devices on different cell buses to share the same UTOPIA bus in ATM mode. Using a glueless interface, the two T8207 devices resolve queue priorities and arbitrate the use of the UTOPIA bus. This shared mode can be used to provide redundancy or increase UTOPIA traffic capacity by supporting traffic from multiple cell buses.

The

CelXpres

T8207 supports the transport of control and loopback cells with an external microprocessor. Control or loopback cells may be sent or received through the microprocessor interface. The 8-bit microprocessor interface may be configured to be

Motorola

Intel

compatible and is used to configure and monitor the device.

Agere Systems Inc. 9

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

1 Product Overview (continued)

5-7542E (F)

Figure 1. Functional Block Diagram

ONE OR TWO

32K TO 256K x 8

LOOK-UP

ENGINE

UTOPIA

INTERFACE

RX PHY

FIFO

(16 CELLS)

CONTROL CELL

TX FIFO (1 CELL)

LOOPBACK

FIFO

(1 CELL)

CONTROL CELL

RX FIFO

(16 CELLS)

TX PHY

FIFO

(128 CELLS)

SDRAM

INTERFACE

TX UTOPIA

1M TO 16M x 16

SDRAM

MICROPROCESSOR

INTERFACE

MICROPROCESSOR

CELL BUS

ARBITER

CELL BUS

MONITORING

CELL BUS

INTERFACE

CELL BUS

UTOPIA

INTERFACE

UTOPIA

(4 CELLS)

INPUT FIFO

(128 CELLS)

CELL BUFFER

(LUT) SRAMs

RX UTOPIA

FIFO

(4 CELLS)

CELL BUS

OUTPUT FIFO

(4 CELLS)

10 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

1 Product Overview (continued)

Figure 2 illustrates the use of the

CelXpres

T8207 in a system with dual backplane cell buses using shared UTOPIA mode. In this configuration, both T8207 devices on each card receive cells from the UTOPIA bus, and each device uses its translation table to determine if the cell should be transmitted on its backplane cell bus. In the egress direction, each T8207 device receives cells from its cell bus to transmit on the UTOPIA bus. MPHY arbitration and queue priorities are resolved using a two-wire interface between the two devices. Although a single ATM virtual connection is not typically established on both backplane cell buses simultaneously, no restrictions exist for a single PHY utilizing both backplane cell buses for different virtual connections supporting higher throughput from two bus interfaces. Redundant bus configurations can be supported in the event of a bus failure with T8207 devices by configuring one device to assume bus responsibility from the other.

0041

Figure 2. Dual Bus Implementation

DOWNSTREAM

BUFFERING

UPSTREAM

TRANSLATION

UTOPIA

T8207

DOWNSTREAM

BUFFERING

UPSTREAM

TRANSLATION

UTOPIA

PHYs

T8207

BACKPLANE

BUS

DOWNSTREAM

BUFFERING

UPSTREAM

TRANSLATION

UTOPIA

T8207

DOWNSTREAM

BUFFERING

UPSTREAM

TRANSLATION

UTOPIA

PHYs

T8207

Agere Systems Inc. 11

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

1 Product Overview (continued)

1.4 Conventions

■ All numbers in this document are decimals unless otherwise specified.

■ Hexadecimal numbers can be identified by the ‘h’ suffix, e.g., A5h.

■ Binary numbers are either in double quotes for multiple bits or in single quotes for individual bits, e.g., “1001” and

‘0.’

■ A byte is 8 bits, a word is 16 bits, and a double word (dword) is 32 bits.

■ A binary value of ‘1’ is high, and a binary value of ‘0’ is low.

■ To clear is to change one or multiple bit values to ‘0.’

■ To set is to change one or multiple bit values to ‘1.’

■ All memory addresses are specified in hexadecimal.

■ Addresses are converted from bytes to words or double words using the little-endian format, unless otherwise

specified.

■ A signal name with a trailing asterisk is active-low, e.g., sd_we*.

■ Bits y to x will be designated bits (y:x).

12 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

1 Product Overview (continued)

1.5 Glossary

Bus Cell:

Major content of the cell bus frame consisting of 56 bytes, 4 bytes for routing options and 52 bytes for the ATM cell content, which excludes the HEC. The bus cell is preceded by the 4 bytes of request and followed by the 4 bytes of grant and parity information.

CLP: Cell loss priority. The CLP is a 1-bit field in the cell header that becomes set when the cell violates the negotiated quality of service parameters.

EFCI: Explicit forward congestion indication. The EFCI is a 1-bit field in the PTI field of the cell header that becomes set when the cell encounters congestion.

FECN: Forward explicit congestion notification. FECN is a method used by the network to signal to the destination when congestion is encountered. The EFCI bit is used to indicate the congestion.

GFC: Generic flow control. The GFC is a 4-bit field in the cell header that may be used by a UNI to support traffic and congestion control. Typically, this field is programmed

to “0000” indicating that generic flow control is not sup-

ported. GFC may be used in priority protocols. Grant Section:

Last 4 bytes of the cell bus frame. The grant section occurs during the last clock cycle of the cell bus frame. During this cycle, the cell bus arbiter indicates which T8207 may transmit during the next bus cell unit of the cell bus frame. A parity vector is also transmitted during the grant section.

HEC: Header error control. The HEC is a 1-byte field in the cell header used for bit error detection and correction in the header.

NNI: Network node interface. The NNI is the interface between nodes in the public network.

OAM Cell: Operations and maintenance cell. An OAM cell carries local management information.

PPD: Partial packet discard. PPD is a technique to relieve congestion. When one cell in a packet is lost, all remaining cells in the packet, except the last, are discarded.

PTI: Payload type identifier. The PTI is a 3-bit field in the cell header containing information about the type of data (user, OAM, or traffic management) and about encountered congestion.

QoS: Quality of service. Quality of service parameters define the performance requirements and characteristics for traffic on an assigned channel. Some parameters include cell loss ratio, cell transfer delay , cell delay variation, peak cell rate, and sustained cell rate.

RM: Resource management. RM is the local management of network resources.

RxCLA V:

Receive cell available signal as described in the ATM

Forum’s universal test and operations PHY interface for ATM (UTOPIA) Level 1, Version 2.01 and Level 2, Version 1.0 specifications.

RxENB:

Receive enable signal as described in the ATM Forum’s universal test and operations PHY interface for ATM (UTOPIA) Level 1, Version 2.01 and Level 2, Version 1.0 specifications.

TxCLA V:

Transmit cell available signal as described in the ATM Forum’s universal test and operations PHY interface for ATM (UTOPIA) Level 1, Version 2.01 and Level 2, Version 1.0 specifications.

TxENB:

Transmit enable signal as described in the ATM Forum’s universal test and operations PHY interface for ATM (UTOPIA) Level 1, Version 2.01 and Level 2, Version 1.0 specifications.

UNI: User network interface. The UNI is the interface between a private network node and a public network node.

VCI: Virtua l channe l iden tifier. The VCI is a 2-byt e fiel d in the cell header that identifies the virtual channel used by the cell.

VPI: Virtual path identifier. The VPI is an 8-bit field in the UNI cell header or a 12-bit field in the NNI cell header that identifies the virtual path of the cell.

Agere Systems Inc. 13

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description

This section defines the

CelXpres

T8207 pins. All TTL compatible inputs or I/O are 5 V tolerant. No GTL+ inputs or

I/O are 5 V tolerant.

Table 1. UTOPIA Pins

Symbol Ball Reset

Value

Type Name/Description

u_rxaddr[4:0] R2, P3, R1, P2, P1Z I/O RX UTOPIA Address Lines. 10 mA drive, TTL compatible I/O,

5 V tolerant.

u_rxdata[7:0] V2, U3, T4, V1,

U2, T3, U1, T2

—IRX UTOPIA Data Lines. TTL compatible input, 5 V tolerant.

u_rxclk T1 Z I/O RX UTOPIA Clock. 10 mA drive, TTL compatible I/O, 5 V tolerant.

u_rxsoc P4 — I RX UTOPIA Start of Cell (Active-High). TTL compatible input,

5 V tolerant.

u_rxclav[0] L4 Z I/O RX UTOPIA PHY 0 Cell Available (Active-High). Main RX cell

available in single PHY mode. 10 mA drive, TTL comp atible I/O, 5 V tolerant. This pin has an internal 50 kΩ pull-up resistor.

u_rxclav[3:1] M3, M2, M1 — I RX UTOPIA Cell Available Lines (Active-High). TTL compatible

input, 5 V tolerant. These pins have an internal 50 kΩ pull-up resistor.

u_rxenb*[0] M4 Z I/O RX UTOPIA PHY 0 Enable (Active-Low). Main RX enable in sin-

gle PHY mode. 10 mA drive, TTL compatible I/O, 5 V tolerant.

u_rxenb*[3:1] N3, N2, N1 Z I/O RX UTOPIA PHY Enable Lines (Active-Low). 10 mA drive, TTL

compatible I/O, 5 V tolerant.

u_rxprty R3 — I RX UTOPIA Odd Parity. TTL compatible input, 5 V tolerant. This

pin has an internal 50 kΩ pull-up resistor.

u_txaddr[4:0] P17, R19, R20,

P18, P19

Z I/O TX UTOPIA Address Lines. 10 mA drive, TTL compatible I/O.

5 V tolerant.

u_txdata[7:0] W20, V19, U19,

U18, T17, V20,

U20, T18

ZOTX UTOPIA Data Lines. 10 mA drive, TTL compatible output.

u_txclk R18 Z I/O TX UTOPIA Clock. 10 mA drive, TTL compatible I/O, 5 V tolerant.

u_txsoc T20 Z O TX UTOPIA Start of Cell (Active-High). 10 mA drive, TTL compat-

ible output.

u_txclav[0] M20 Z I/O TX UTOPIA PHY 0 Cell Available (Active-High). Main TX cell

available in single PHY mode. 10 mA drive, TTL comp atible I/O. 5 V tolerant. This pin has an internal 50 kΩ pull-up resistor.

u_txclav[3:1] M17, M18, M19 — I TX UTOPIA Cell Available Lines (Active-High). TTL compatible

input, 5 V tolerant. These pins have an internal 50 kΩ pull-up resistor.

u_txenb*[0] N20 Z I/O TX UTOPIA PHY 0 Enable (Active-Low). Main TX enable in single

PHY mode. 10 mA drive, TTL compatible I/O, 5 V tolerant.

u_txenb*[3:1] P20, N18, N19 Z O TX UTOPIA Enable Lines (Active-Low). 10 mA drive, TTL com-

patible output. u_txprty T19 Z O TX UTOPIA Odd Parity. 10 mA drive, TTL compatible output. u_shr_o V16 1 O Shared UTOPIA Output. Used as grant if device is shared

UTOPIA master or as request if device is shared UTOPIA slave.

4 mA drive, TTL compatible output. This pin has an internal 50 kΩ

pull-up resistor.

u_shr_i W17 — I Shared UTOPIA Input. Used as request if device is shared

UTOPIA master or as grant if chip is shared UTOPIA slave. TTL

compatible input, 5 V tolerant. This pin has an internal 50 kΩ pull-

up resistor.

14 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

Table 2. Cell Bus Pins

Symbol Ball Reset

Value

Type Name/Description

ua*[4:0] B18, B17, C17,

D16, A18

—I

Unit Address Lines (Active-Low).

Address assigned to device for cell bus identification. TTL compatible input, 5 V tolerant.

cb_d*[31:0] B5, C6, D7, A5,

B6, C7, A6, B7, A7, C8, B8, A8, D9, C9, B9, A9,

A11, C11, B11, A12, B12, C12, D12, A13, B13, C13, A14, B14, C14, A15, B15,

D14

Z I/O Cell Bus Data Lines (Active-Low). GTL+ I/O.

cb_wc* A10 — I Cell Bus Write Clock (Active-Low). Uses falling edge to

output data on cell bus. Write and read clocks have the same frequency but different phase. GTL+ input.

cb_rc* B10 — I Cell Bus Read Clock (Active-Low). Uses falling edge to

latch data from cell bus. Write and read clocks have the same frequency but different phase. GTL+ input.

cb_fs* C15 Z I/O Cell Bus Frame Sync (Active-Low). GTL+ I/O.

cb_ack* B16 Z I/O Cell Bus Acknowledge Signal (Active-Low). Driven low

on cycle 0 of the following frame when a valid cell is received from the cell bus. This signal is not driven for broadcast or multicast cells. GTL+ I/O.

arb_en* A17 — I Cell Bus Arbiter Enable (Active-Low). Cell bus arbiter

enable. Only one device on the cell bus may be configured as arbiter. TTL-compatible input , 5 V tolerant. This pin has an internal 50 kΩ p ul l- up re si st or.

cb_disable* C16 — I Cell Bus Disable (Active-Low). CMOS input that 3-states

all GTL+ outputs when low, but GTL+ buffer inputs are active. This pin has an internal 50 kΩ pull-up resistor.

cb_iref A4 — I Cell Bus Current Reference. Precision current re ferenc e

for GTL+ buffers. A 1 kΩ, 1% resistor must be connected between this pin and GND.

cb_vref D10 — I Cell Bus V o lt age Re feren ce. G TL+ buffer threshold voltage

reference (1.0 V typical). This voltage reference is 2/3 V

TT,

created using a voltage divider of three 1 kΩ, 1% resistors between V

TT and cb_vref_vss.

cb_vref_vss C10 — — Cell Bus Voltage Reference Ground.

Agere Systems Inc. 15

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

T able 3. SDRAM Interface Pins

Symbol Ball Reset

Value

Type Name/Description

sd_a[11:0] L19, L18, L20,

K20, K19, K18,

K17, J20, J19,

J18, J17, H20

SDRAM Address Lines. 7 mA drive, TTL compatible output. These buffers are 50 Ω impedance matching buffers. Long printed-wiring board traces should have 50 Ω nominal impedance.

sd_d[15:0] F19, E20, G17,

F18, E19, D20,

E18, D19, C20 E17, D18, C19, B20, C18, B19,

A20

Z I/O

SDRAM Data Lines. 7 mA drive, TTL comp atib le I/O. Th ese buffers are 50 Ω

impedance matching buffers. Long printed-

wiring board traces should have 50 Ω nominal impedance.

sd_bs[1:0] H18, G20 X O

SDRAM Bank Selects. 7 mA drive, TTL compatible output. These buffers are 50 Ω

impedance matching buffers. Long printed-wiring board traces sh ould have 50 Ω nominal impedance.

sd_ras* G19 1 O

SDRAM Row Address Select (Active-Low). 7 mA drive, TTL compatible output. This buffer is a 50 Ω

impedance matching buffer. Long printed-wiring board traces should have 50 Ω nominal impedance.

sd_cas* F20 1 O

SDRAM Column Address Select (Active-Low). 7 mA drive, TTL compatible output. This buffer is a 50 Ω

impedance matching buffer. Long printed-wiring board traces should have 50 Ω nominal impedance.

sd_we* G18 1 O

SDRAM Write Enable (Active-Low). 7 mA drive, TTL compatible output. This buffer is a 50 Ω

impedance matching buffer. Long printed-wiring board traces should have 50 Ω nominal impedance.

sd_clk H19 Z I/O

SDRAM Clock. 7 mA drive, TTL compatible output. This buffer is a 50 Ω

impedance matching buffer. Long printed-

wiring board traces should have 50 Ω nominal impedance.

sd_iref A19

—ISDRAM Current Reference. Precision current reference for

SDRAM buffers. A 1 kΩ, 1% resistor must be connected between this pin and GND.

16 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

Table 4. Microprocessor Interface Pins

Symbol Ball Reset

Value

Type Name/Description

a[7:1] W6, Y6, V7 , W7,

Y7, V8, W8

—IMicroprocessor Port Address Lines. Most significant

7 bits of the address bus. TTL compatible input, 5 V tolerant.

a[0]/ale Y8 — I Microprocessor Port Address 0/Address Latch Enable.

Least significant bit of the address bus in nonmultiplexed mode or address latch enable in multiplexed mode.

d[7:0] U9, V9 W9, Y9,

W10, V10, Y10,

Y11

Z I/O Microprocessor Port Data Lines. 6 mA driv e, T TL co mpat-

ible I/O, 5 V tolerant.

sel* W12 — I Microprocessor Chip Select (Active-Low). TTL compati-

ble input, 5 V tolerant.

wr*_ds* V12 — I Microprocessor Write/Data Strobe. Active-low write

enable in

Intel

mode. Active-low data strobe in

Motorola

mode. TTL compatible input, 5 V tolerant.

rd*_rw* U12 — I Microprocessor Read/Write. Active-low read enable in

Intel

mode, or read/write* enable in

Motorola

mode, where read is active-high and write is active-low. TTL compatible input, 5 V tolerant.

int_irq* Y12 0/1 O CPU Interrupt. Active-high in

Intel

mode and active-low in

Motorola

mode. 4 mA drive, TTL compatible output.

rdy_dtack* U11 Z O Ready/Data Transfer Acknowledge. Active-high ready sig-

nal in

Intel

mode and active-low data transfer acknowledge

Motorola

mode. Indicates access complete. 6 mA drive,

TTL compatible output.

mot_sel Y13 — I

Intel/Motorola

Selection. ‘0’ =

Intel

, ‘1’ =

Motorola

. TTL

compatible input, 5 V tolerant.

mux W13 — I Microprocessor Multiplex Select. Active-high for multiplex

mode. TTL compatible input, 5 V tolerant.

Agere Systems Inc. 17

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

T able 5. Translation SRAM Interface

Table 6. JTAG Pins

Symbol Ball Reset

Value

T ype Name/Description

tr_a[17:0] L3, L2, L1, K1,

K3, K2, J1, J2, J3, J4, H1, H2,

H3, G1, G2, G3,

F1, F2

XOTranslation RAM Address Lines. 4 mA drive, TTL compat-

ible output.

tr_d[7:0] E3, D1, C1, E4,

D3, D2, C2, B1

Z I/O Translation RAM Data Lines. 4 mA drive, TTL compatible

I/O, 5 V tolerant.

tr_cs*[1:0] E1, E2 1 O Translation RAM Chip Selects (Active-Low). Chip selects

to select one of two external SRAMs. For connection to one external device, tr_cs*[0] is used. 4 mA drive, TTL compatible output.

tr_oe* F3 1 O External RAM Output Enable (Active-Low). 4 mA drive,

TTL compatible output.

tr_we* G4 1 O External RAM Write Enable (Active-Low). 4 mA drive,

TTL compatible output.

Symbol Ball Reset

Value

T ype Name/Description

jtag_tdi Y16 —ITest Data Input (JTAG). TTL compatible input, 5 V tolerant.

This pin has an internal 50 kΩ pull-up resistor.

jtag_tdo W16 X O Test Data Output (JTAG). 4 mA drive, TTL compatible out-

put.

jtag_trst* W15 — I Test Reset (JTAG) (Active-Low). Should be pulled low

when part is in normal operation. TTL compatible input, 5 V tolerant. This pin has an internal

50 kΩ pull-up resistor.

jtag_tclk V15 — I

T est Clock (JTAG).

TTL compatible input, 5 V tolerant. This

pin has an internal 50 kΩ pull-up resistor.

jtag_tms U14 — I

Test Mode Select (JTAG).

TTL compatible input, 5 V toler-

ant. This pin has an internal 50 kΩ pull-up resistor.

18 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

Table 7. General-Purpose Pins

Table 8. Power Pins

Symbol Ball Reset

Value

Type Name/Description

gpio[7:0] U5, Y3, Y4, V5,

W5, Y5, V6, U7

— I/O General-Purpose I/O. 4 mA drive, TTL compatible I/O, 5 V

tolerant.

reset* V14 — I Reset (Active-Low). Schmitt trigger, TTL compatible input,

5 V tolerant.

xtalin V13 — I Crystal Input (pclk). This input may be driven by either a

crystal or an external clock. If a crystal is used, connect it between this pin and xtalout and connect the appropriately valued capacitor from this pin to V

SS.

If an external clock is used, this is a 5 V tolerant CMOS input with 50 MHz max input frequency.

xtalout Y14 — O Crystal Output Feedback. If a crystal is used, connect it

between this pin and xtalin and connect the appropriately valued capacitor from this pin to V

SS. If an external clock is

used to drive xtalin, this pin must be left unconnected.

cko W11 — O Buffered Clock Output. If enabled, pclk is output on this

pin. 8 mA drive, TTL compatible output. This pin is high impedance if not enabled.

cko_e V11 — I CKO Enable. Enable for buffered clock output. If cko is not

used, tie this enable pin low. Active-high, TTL compatible input, 5 V tolerant.

NC A2, A3, A16 , B2,

B3, B4, C3, C4,

C5, D5, U16, V3,

V4, V17, V18,

W1, W2, W3,

W4, W18, W19,

Y1, Y2, Y15,

Y17, Y18, Y19,

Y20

——No Connection. Reserved.

Symbol Ball Name/Description

DD D6, D11, D15, F4, F17, K4, L17, R4, R17, U6,

U10, U15

Power. 3.3 V. These pins should be properly decoupled using 0.01 µF or 0.1 µF capacitors.

SS A1, D4, D8, D13, D17, H4, H17, J9, J10, J11,

J12, K9, K10, K11, K12, L9, L10, L11, L12, M9,

M10, M11, M12, N4, N17, U4, U8, U13, U17

Ground.

DDA W14 Clock Oscillator Power. 3.3 V. This pin should

be properly decoupled using 0.01 µF or 0.1 µF capacitors.

Agere Systems Inc. 19

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

2 Pin Description (continued)

5-8013(f)

Figure 3. 272-Pin PBGA—Top Vie w

VDD

VSS

VSS VDD VSS VSS VDD VSS

VDD

VSS

VDD

VSS

VDD

VDDVSS VDD VSS VSS VDD VSS

VDD

VSS

VDD

VSS

VDD

1234567891011121314151617181920

VSS VSS VSS VSS

20 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

3 Powerup/Reset Sequence

One of the following two methods may be used to reset the T8207:

1. Assert the reset* pin low for at least 5 pclk periods or 100 ns, whichever is longer, and then return it high for a hardware reset. For a powerup reset, the reset* pin should be held low for at least 5 pclk periods or 100 ns, whichever is longer, after the power supply ramps to its operating voltage and the crystal oscillator is stable.

Write both the srst* and srst_reg* bits in the direct configuration/control register (address 28h) to ‘0,’ and leave them at that value for at least 1 µs to perform a software reset.

The device is now in the reset state, and the following start-up procedure must be executed to ensure proper operation:

1. After pclk (xtalin) is provided to the T8207, and the device is in the reset state: A. Write the mclk PLL configuration 0 and 1 registers at addresses 2Ah and 2Bh.

Continue after the PLL has stabilized in 100 µs

2. Set the srst_reg* bit (to take the main registers out of reset), and program the cyc_per_acc and big_end bits in the direct configuration/control register (address 28h).

3. Wait 1 µs for the circuit to stabilize.

Extended memory accesses may now be performed only to the main register group.

4. Write the desired values to the main configuration 1 register (address 0100h), the TX UTOPIA clock configuration register (address 010Ch), and the RX UTOPIA clock configuration register (address 010Eh) in the extended memory registers. These bits should not be modified at a later time without returning to the reset state.

5. Program the main configuration 2 register (address 0112h) and the UTOPIA configuration register (address 0114h). These registers should not be modified at a later time without returning to the reset state.

6. Program the cb_arb_sel and cb_usr_mode bits in the cell bus configuration/status register (address 0130h).

7. Wait one clock period of the slowest clock (cell bus, UTOPIA, or pclk) for the circuit to stabilize.

8. Set the srst* bit in the direct configuration/control register (address 28h).

9. Wait three clock periods of the slowest clock (cell bus, UTOPIA, or pclk) for the circuit to stabilize.

The T8207 device is now out of reset state.

10. Initialize the SDRAM per the SDRAM specifications.

11. Enable the SDRAM by setting the sdram_en bit in the SDRAM control register (address 0400h).

12. Initialize the LUT to benign values (recommended).

13. Initialize the multicast memory to all ’0’ (recommended).

14. Program the three routing information registers (addresses 0200h through 0204h) and the seven PPD information registers (addresses 0206h through 0212h).

Agere Systems Inc. 21

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

4 Hot Insertion

When a connector with proper pin sequencing is used, the Agere Systems Inc. GTL+ buffers withstand hot insertion into a backplane without corrupting the cell bus or damaging the device. The ground pins on the connector should extend beyond all other pins so that the ground connections are made first. In addition, the power pins on the connector should extend beyond the signal pins so that the power connections are made before the signal but after the ground connections.

During hot insertion, the cell bus is not corrupted because the GTL+ outputs go to a high-impedance state during the powerup reset. Therefore, proper timing should be met in the external powerup reset circuit.

22 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

5 PLL Configuration

The frequency of the device’s main clock (mclk) is derived from the clock at the xtalin input (pclk) and is given by the following equation when the PLL is engaged:

mclk = fpclk x

Note: When the PLL is engaged, mclk is the output of the PLL.

M and N are the pll_m[4:0] and pll_n[2:0] counter values in the mclk PLL configuration 1 register (address 2Bh) and must be set so that the voltage-controlled oscillator (VCO) operates in the appropriate range. The maximum value for f

mclk is 100 MHz. The valid range for M is between 2 and 22 inclusive, and the valid range for N is between 0

and 7 inclusive. When multiple sets of values can achieve the desired result, choose the lowest value of M and the corresponding value for N.

Note: The output of the PLL must always be at least 50 MHz.

The loop filter must be set properly for correct operation of the PLL. The proper setting of the loop filter bits, lf[3:0], in the mclk PLL configuration 0 register (address 2Ah) is determined by the chosen value for M. The following table lists the lf[3:0] settings for given values of M. Typical PLL lock-in time is 50 µs.

Table 9. Loop Filter Register Settings

PLL Configuration Example

Given a pclk frequency of 50 MHz and a desired mclk frequency of 100 MHz, the proper values of M, N, and lf[3:0] are the following:

M = 2 N = 7

lf[3:0] = “0010” The bypass PLL (bypb) and PLL enable (pllen) bits are used to select the source of mclk for the T8207. To select

the output of the PLL as the clock, both bits must be programmed to ‘1,’ and to select pclk as the clock, both bits must be programmed to ‘0.’

M Mclk PLL Configuration 0

(2Ah) lf[3:0]

22 “0111” 16—21 “0110” 10—15 “0101”

6—9 “0100” 4—5 “0011” 2—3 “0010”

()

2MOD8N1

()1

()×()

------------------------------------------------------------------

Agere Systems Inc. 23

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

6 Microprocessor Interface

6.1 Microprocessor Interface Configura tion

The microprocessor interface may be configured for either

Intel

Motorola

mode via the mot_sel input. Tie

mot_sel high to select

Motorola

mode and low to select

Intel

mode. In addition, the address and data buses may be configured for multiplexed or nonmultiplexed mode using the mux input. To select multiplexed mode, tie mux high, and to select nonmultiplexed mode, tie mux low. In multiplexed mode, d[7:0] are used for both the address and the data bus, and the a[0] input becomes an address latch enable (ale) signal. In nonmultiplexed mode, separate address, a[7:0], and data, d[7:0], buses are used. In both modes, the active-low sel* input selects the device for microprocessor read or write accesses. The data leads are 3-stated when the sel*, wr*_ds*, or rd*_wr* signal is high.

Motorola

mode, rd*_rw* is a read/write enable signal, which indicates the current access is a read when it is high

and a write when low. The wr*_ds* signal is data strobe in

Motorola

mode. The rdy_dtack* output is an active-low data transfer acknowledge signal. The T8207 takes this signal low when the microprocessor access is complete. The rdy_dtack* output returns high when the microprocessor acknowledges the access by taking the sel* or wr*_ds* signal high. The rdy_dtack* output then goes high-impedance.

Intel

mode, the rd*_rw* input is an active-low read enable signal, and wr*_ds* is an active-low write enable signal. A logic low level on rd*_rw* indicates to the T8207 that the current access is a read, and a logic low level on wr*_ds* indicates the access is a write. Finally, the rdy_dtack* output is an active-high ready signal. The T8207 asserts this signal high when a microprocessor access is complete. The rdy_dtack* output then goes high-impedance when the sel*, wr*_ds*, or rd*_wr* signal goes high.

6.2 Microprocessor Interrupts

The int_irq* output is an active-high interrupt in

Intel

mode and an active-low interrupt request in

Motorola

mode. In

Intel

mode, int_irq* is normally low and goes high when an interrupt is generated. In

Motorola

mode, the interrupt request signal is normally high and goes low during an interrupt. Interrupts are generated when an enabled interrupt status bit becomes set. All interrupt status bits in the T8207 have a corresponding interrupt enable bit. When the enable bit is cleared, the corresponding interrupt status bit is not enabled and will not generate an interrupt. Several registers containing interrupt status bits exist in the three separate extended memory register groups (main, UTOPIA, and SDRAM) of the T8207. The interrupt service request register at direct address 29h indicates which register group is generating the interrupt. Only enabled interrupts will cause the int_serv_mainreg, int_serv_sdramreg, and int_serv_utopiareg bits to become set. For the main register group, a special case exists. The ctrl_cell_sent and the ctrl_cell_av interrupts (in the main interrupt status 1 register) do not cause the main group indication bit to be set in the interrupt service request register. These interrupts have their own dedicated service request bits to optimize sending and receiving control cells. The ctrl_cell_sent and ctrl_cell_av bits may become set whether the corresponding interrupt is enabled or not.

6.3 Accessing the

CelXpres

T8207 via Microprocessor Interface

The

CelXpres

T8207 has two distinct memory spaces, the direct memory access registers and the extended memory registers. The direct memory access registers are directly addressed 8-bit (byte) registers and are mapped between addresses 00h and FFh. The extended memory registers are indirectly addressed and mapped between addresses 0100h and 3FFFFFEh. The extended memory contains the SDRAM memory, the translation RAM,

internal memories, and the device’s configuration, status, and control registers. Extended memory registers are 16 bits wide, and all accesses to the extended memory registers are executed internally as 16 bits. Direct memory access registers are located in Section 14.2, Direct Memory Access Registers, and extended memory registers are located in Section 14.3, Extended Memory Registers.

24 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

6 Microprocessor Interface (continued)

6.3.1 Accessing the Extended Memory Registers

Before accessing the extended memory registers, the powerup sequence, as described in Section 3, Powerup/ Reset Sequence, must be completed. Accesses to extended memory are word accesses internally; therefore, the

least significant bit of the address is always ‘0.’ Only the most significant 25 bits are supplied to the extended memory address registers (addr es ses 30h—34h). The following procedure outlines the steps needed for extended

memory accesses in the T8207 device.

6.3.1.1 Extended Memory Writes

1. Write ext_a [25] bit to the extended memory address 4 register (little endian or big endian) (optional).

2. Write ext_a [24:17] byte to the extended memory address register 3 (little endian or big endian) (optional).

3. Write ext_a [16:9] byte to the extended memory address register 2 (little endian or big endian) (optional).

4. Write ext_a [8:6] bits to the extended memory address register 1 (little endian or big endian) (optional).

5. Write ext_d [15:8] byte to the extended memory data high register (little endian or big endian) (optional).

6. Write ext_d [7:0] byte to the extended memory data low register (little endian or big endian) (optional).

7. Write ext_a [5:1] bits; write “01,” “10,” or “11” to ext_we[1:0]; and write ‘1’ to ext_strt_acc in the extended memory access register (little endian or big endian) (mandatory).

8. Read the extended memory access register (little endian or big endian) to determine that the ext_strt_acc bit has been cleared by hardware (mandatory).

6.3.1.2 Extended Memory Reads

1. Write ext_a [25] bit to the extended memory address 4 register (little endian or big endian) (optional).

2. Write ext_a [24:17] byte to the extended memory address register 3 (little endian or big endian) (optional).

3. Write ext_a [16:9] byte to the extended memory address register 2 (little endian or big endian) (optional).

4. Write ext_a [8:6] bits to the extended memory address register 1 (little endian or big endian) (optional).

5. Write ext_a [5:1] bits; write “00” to ext_we[1:0]; and write ‘1’ to ext_strt_acc in the extended memory access register (little endian or big endian) (mandatory).

6. Read the extended memory access register (little endian or big endian) to determine that the ext_strt_acc bit has been cleared by hardware (mandatory).

7. Read ext_d [15:8] byte from the extended memory data high register (little endian or big endian) (optional).

8. Read ext_d [7:0] byte from the extended memory data low register (little endian or big endian) (optional).

Note: Once the ext_strt_acc bit is set by software, only the extended memory access register should be

accessed until the ext_strt_acc bit is cleared by hardware.

Agere Systems Inc. 25

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

6 Microprocessor Interface (continued)

6.3.2

CelXpres

T8207 Access Performance

The times represented in the following table reflect access times for various microprocessor interface reads and writes. For direct access registers, the values represent the time until the rdy_dtack signal transitions indicating the data transfer portion of the access is complete. For accesses to extended memory, the values represent the time from the completion of a write to register 34h until the ext_strt_acc bit is cleared.

The actual times are dependent on the frequency of the pclk and mclk clocks (see Section 5, PLL Configuration). The terms pclkp and mclkp in the table represent the period of pclk and mclk, respectively, in ns.

Table 10. Access Times

Description Min Typ Max Unit

Read/Write to 28h—3Dh 4 x pclkp 5 x pclkp 5 x pclkp + 30 ns Reads to:

60h—93h, A0h—D7h, E0h—FFh

(direct internal memory)

6 x pclkp + 3 x mclkp 8 x pclkp + 9 x mclkp 12 x pclkp + 15 x mclkp ns

Writes to:

60h—93h, A0h—D7h, E0h—FFh

(direct internal memory)

6 x pclkp 8 x pclkp + 4 x mclkp 10 x pclkp + 9 x mclkp ns

Reads to Extended Memory

Internal Structures

6 x pclkp + 6 x mclkp 8 x pclkp + 12 x mclkp 12 x pclkp + 18 x mclkp ns

Writes to Extended Memory

Internal Structures

6 x pclkp 8 x pclkp + 7 x mclkp 10 x pclkp + 12 x mclkp ns

Read from LUT SRAM 4 x pclkp + 11 x mclkp — 10 x pclkp + 50 x mclkp ns Write to LUT SRAM 4 x pclkp — 10 x pclkp + 50 x mclkp ns

26 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

7 General-Purpose I/O (GPIO)

The T8207 has eight programmable general-purpose I/O pins called GPIO. These GPIO pins may be independently programmed, via the GPIO_oe[7:0] bits in the GPIO output enable register (address 39h), to be inputs or

outputs. If a GPIO_oe bit is set to ‘1,’ the corresponding GPIO pin is an output, or if cleared to ‘0,’ the corresponding GPIO pin is an input. Input values are read from the GPIO_in[7:0] bits in the GPIO input value register (address 3Dh), and output values are written to the GPIO_out[7:0] bits in the GPIO output value register (address 3Bh). The GPIO[7:0] pins all have internal 50 kΩ pull-up resistors.

Agere Systems Inc. 27

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table

Cells arriving from the UTOPIA bus obtain information from the external static RAM look-up table (LUT), which is divided among VPI, VCI, and OAM/RM records. Each of these records contains specific VPI or VPI/VCI translation and cell bus routing information. The size of the records is programmable to 8 bytes or an extended 16 bytes. The 16-byte mode adds two 32-bit counters to each record. The 16-byte mode is discussed in Section 8.4, Extended Records.

The VPI value in the header, in addition to the PHY port number, of the incoming cell points to a VPI record in the look-up table. This VPI record is examined first. If the VPI record indicates OAM F4 routing, the OAM record, to which the VPI record points, provides the OAM routing and VPI/VCI translation information. If OAM F4 routing is not indicated, information about the type of translation, VPI only or VPI/VCI, is obtained from the original VPI record. For VPI only translation, routing information is obtained from the VPI record, and full or partial VPI translation is performed.

For VPI/VCI translation, the VPI record points to the appropriate VCI record, where VPI/VCI translation and routing information is stored. If the VCI record indicates OAM F5 routing, the OAM record, to which the VCI record points, provides the OAM routing and VPI/VCI translation information. If no OAM F5 routing is indicated, VPI/VCI translation and cell routing is performed using the information in the VCI record.

8.1 Look-Up Table RAM

The number of memory devices (up to two) used for the look-up table and the size of the external SRAM are programmable. The tram_qnty_sel bit in the main configuration 1 register (address 0100h) specifies whether one or two RAM chips are used. If two memory devices are used, separate chip select signals are generated. These chip selects are created from the decoded RAM addresses. The tram_size configuration bits, also in the main configuration 1 register, are used to select memory sizes of 32 Kbytes, 64 Kbytes, 128 Kbytes, or 256 Kbytes. Therefore, the maximum look-up table size of 512 Kbytes is realized when two RAM chips of 256 Kbytes each are used.

28 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

8.2 Organization

Organization is discussed in terms of 8-byte records. Differences in organization for 8-byte records and 16-byte records will be discussed in Section 8.4, Extended Records. The look-up table may be configured to support up to 16 ports when multi-PHY mode is used, effectively creating a separate look-up table for each port.

For 32 ports, each even and odd pair of ports share a look-up table space.

All VPI, VCI, and OAM/RM records may be either 8 bytes or 16 bytes in length. (See Section 8.4, Extended Records for information on 16-byte records.) Figure 4 shows the translation RAM memory map for 8-byte records when the device is configured for 16 or less PHY ports. When greater than 16 PHY ports are used, the look-up table is shared between even and odd ports. Figure 5 shows this translation RAM memory map. OAM/RM translation records are located at the bottom of the memory space with 64 OAM/RM records used by each port. If the device is configured to support 16 to 32 ports, the first 1024 records will be used for OAM and RM translation records. This translates to 8 Kbytes of memory for 8-byte records. The remaining memory is then used for VPI and VCI records. For 8-byte records, when 16 ports or less are used, the base addresses of the OAM records are calculated from the following equation:

OBA = PN × 8 × 64 In this equation, OBA is the OAM base address, PN is the port number, 8 is the number of bytes per record, and 64

is the number of records per port. For example, the OAM/RM translation records for port 2 will have a base address of 1024 or 400h.

For 8-byte records, when greater than 16 ports are used, the base addresses of the OAM records are calculated from the following equation:

OBA = INT(PN/2) × 8 × 64 In this equation, OBA is the OAM base address, PN is the port number; 8 is the number of bytes per record, and 64

is the number of records per port. The INT function specifies that the term within the parentheses is an integer, i.e., the fractional part is discarded. For example, the OAM/RM translation records for port 5 will have a base address of 1024 or 400h.

Note: If the device is configured to use less than 16 ports, the OAM/RM translation record memory space will be

allocated enough memory to handle ports 0 through the maximum port number used. For example, if the device is configured to use ports 0, 2, 4, and 6 (see Section 9, UTOPIA Interface), the OAM/RM translation record memory space will use 448 records (for ports 0 through 6). OAM/RM translation record memory space for ports 1, 3, and 5 will be skipped even though the ports are not used.

Note: If the device is configured in PHY mode (see Section 9, UTOPIA Interface), the device supports only a single

PHY and the translation RAM memory will be addressed as port 0.

Separate VPI record base addresses may be set up for each port in multi-PHY mode (for up to 16 ports), and the number of incoming VPI bits used as a pointer into the look-up table may be programmed. (See Section 14.3, Extended Memory Registers, Table 103.) For 8-byte records, when 16 ports or less are used, the total memory used by the VPI records is calculated using the following equation:

MS = NP x 2

x 8

In this equation, MS is the memory size used for VPI records, NP is the number of ports used, 8 is the number of bytes per record, and NB is the number of incoming VPI bits used to address the look-up table.

For 8-byte records, when greater than 16 ports are used, the total memory used by the VPI records is calculated using the following equation:

MS = INT(NP/2) x 2

x 8

In this equation, MS is the memory size used for VPI records, NP is the number of ports used (greater than 16), 8 is the number of bytes per record, and NB is the number of incoming VPI bits used to address the look-up table. The INT function specifies that the term within the parentheses is an integer, i.e., the fractional part is discarded.

This calculated memory space must be reserved for VPI records.

Agere Systems Inc. 29

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Figure 4. Translation RAM Memory Map—8-Byte Records, for Up to 16 Ports

The four translation record types (VCI, OAM/RM, VPI only, and VPI for VPI/VCI) for 8-byte records are illustrated in Figure 6. There are two types of VPI translation records: one for VPI translation only and one for VPI/VCI translation. The VPI only translation record differs from other records in that it has the SH and SL bits which are used to indicate full or partial VPI translation. (See Table 12, the VPI Value Truth Table.) The other VPI record is used when VPI/VCI translation occurs. It has the VCI offset bits and max VCI value bits which are used to point to the VCI record where translation and routing information reside. The maximum VCI offset is 19 bits in length; therefore, only bits 3 through 18 are stored in the VPI record.

To address the appropriate VCI translation record, the VCI from the cell’s header is multiplied by 8 and added to bits 3 through 18 of the VCI offset which is obtained from the VPI record. This sum is the final offset into the lookup table. This final offset should then be added to the translation RAM memory beginning address 100000h (Table

125) to obtain the final address. The max VCI value indicates the maximum number of VCI translation records in the table. Therefore, if the VCI from the cell’s header is greater than the max VCI value, the cell’s VCI is out of range and is counted as a misrouted cell. Note that VPI records from different ports may reference the same VCI translation record. Other control bits in these records are described following Figure 6.

ROUTING LOOK-UP MEMOR Y MAP OAM CELL ROUTING PORT X RECORD MAP

0000h OAM CELL ROUTING PORT 0 +0000h VP OAM VCI = 0 (F4) 0200h OAM Cell Routing Port 1 •

•

0400h OAM CELL ROUTING PORT 2 0600h OAM CELL ROUTING PORT 3 0800h OAM CELL ROUTING PORT 4 +00F8h VP OAM VCI = 31 (F4)

0A00h OAM CELL ROUTING PORT 5 +0100h VP OAM VCI = 6 & PT = “110” (F4) (RM-VPC)

0C00h OAM CELL ROUTING PORT 6 +0108h VC OAM PTI = “100” (F5) 0E00h OAM CELL ROUTING PORT 7 +0110h VC OAM PTI = “101” (F5)

1000h OAM CELL ROUTING PORT 8 +0118h VC OAM PTI = “110” (F5) 1200h OAM CELL ROUTING PORT 9 +0120h VC OAM PTI = “111” (F5) 1400h OAM CELL ROUTING PORT 10 +0128h RESERVED 1600h OAM CELL ROUTING PORT 11 +0130h RESERVED 1800h OAM CELL ROUTING PORT 12 •

•

1A00h OAM CELL ROUTING PORT 13 1C00h OAM CEL L ROUTING PORT 14 1E00h OAM CELL ROUTING PORT 15 +01F8h RESERVED

2000h

ANY PURPOSE LOOK-UP MEM O RY

SHARED BETWEEN EACH OF THE

16 PORTS

7FFFFh

30 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Figure 5. Translation RAM Memory Map—8-Byte Records, for Greater than 16 Ports

ROUTING LOOK-UP MEMORY MAP OAM CELL ROUTING PORT X RECORD MAP

0000h OAM CELL ROUTING PORT 0 AND 1 +0000h VP OAM VCI = 0 (F4) 0200h OAM CELL ROUTING PORT 2 AND 3 •

•

0400h OAM CELL ROUTING PORT 4 AND 5 0600h OAM CELL ROUTING PORT 6 AND 7 0800h OAM CELL ROUTING PORT 8 AND 9 +00F8h VP OAM VCI = 31 (F4)

0A00h OAM CELL ROUTING PORT 10 AND 11 +0100h VP OAM VCI = 6 & PT = “110” (F4) (RM-VPC)

0C00h OAM CELL ROUTING PORT 12 AND 13 +0108h VC OAM PTI = “100” (F5) 0E00h OAM CELL ROUTING PORT 14 AND 15 +0110h VC OAM PTI = “101” (F5)

1000h OAM CELL ROUTING PORT 16 AND 17 +0118h VC OAM PTI = “110” (F5) 1200h OAM CELL ROUTING PORT 18 AND 19 +0120h V C OAM PTI = “111” (F5) 1400h OAM CELL ROUTING PORT 20 AND 21 +0128h RESERVED 1600h OAM CELL ROUTING PORT 22 AND 23 +0130h RESERVED 1800h OAM CELL ROUTING PORT 24 AND 25 •

•

1A00h OAM CELL ROUTING PORT 26 AND 27 1C00h OAM CELL ROUTING PORT 28 AND 29 1E00h OAM CELL ROUTING PORT 30 AND 31 +01F8h RESERVED

2000h

ANY PURPOSE LOOK-UP MEMORY

SHARED BETWEEN EACH OF THE

16 PAIRS OF PORTS

7FFFFh

Agere Systems Inc. 31

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Figure 6. Translation Record Ty pes—8 -Byte Records

The routing control bits for VPI, VCI, and OAM/RM records are described below:

■ Active (A). This bit is one when the VPI or VCI is considered active. See the truth table (Table 11) below. This bit

is used in all types of records.

■ Ignore (I). When this bit is one, the VPI or VCI is ignored. See the truth table (Table 11) below . This bit is used in

all types of records.

Table 11. Active and Ignore Truth Table

VPI ONLY TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A P E I VPI[11:0] +2 SH SL RES ERVED +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0]

VPI for VPI/VCI Translation Record

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A P E I RESERVED +2 BITS 3 THROUGH 18 OF VCI OFFSET[15:0] +4 MAX VCI VALUE[15:0] +6 RESERVED

VCI TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A — E I VPI[11:0]

+2 VCI[15:0] +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0]

OAM/RM TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A C1 C0 I VPI[11:0] +2 VCI[15:0] +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0]

AI Action

0 0 The cell is discarded, considered misrouted, and counted as a received cell. 0 1 The cell is discarded, is not flagged as misrouted, and is not counted as a received cell. 1 0 The cell is valid and is counted as a received cell. 1 1 The cell is discarded, is not flagged as misrouted, and is not counted as a received cell.

32 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

■ Enable OAM/RM Routing (E). When this bit is ‘1’ in the VPI record and the VCI is less than 32, the routing and

translation information is obtained from the appropriate OAM/RM F4 record. If this bit is ‘1’ in the VCI record and the most significant bit of the PTI in the cell header is ‘1,’ the routing and translation information is obtained from the appropriate OAM/RM F5 record. This bit is used only in VPI and VCI records.

■ VPI Translation (P). When this bit is ‘1,’ translation is on the VPI only. When this bit is ‘0,’ VPI/VCI translation is

performed. This bit is used only in VPI records.

■ VPI Value High (SH). When this bit is ‘1,’ bits 8 through 11 of the incoming VPI are replaced with the correspond-

ing bits in the VPI record. See the truth table (Table 12) below. This bit is used in VPI only translation records.

■ VPI Value Low (SL). When this bit is ‘1,’ bits 0 through 7 of the incoming VPI are replaced with the corresponding

bits in the VPI record. See the truth table (Table 12) below. This bit is used in VPI only translation records.

Table 12. VPI Value Truth Table

■ OAM Routing Control (C1, C0). These 2 bits determine if the cell is routed as OAM/RM and if VPI/VCI translation

is performed. See the truth table (Table 13) below. These bits are used only in OAM/RM records.

Table 13. OAM Routing Control Truth Table

1. The most significant 4 bits of the VPI will only be substituted if the global rplc_gfc bit in the direct configuration/control register (address 28h) is set in UNI mode or if the port is configured in NNI mode.

SH SL Action

0 0 No VPI translation is performed. 01VPI translation is performed only on bits 0—7 of the incoming VPI.

1 0 VPI translation is performed only on bits 8—11 of the incoming VPI. 1 1 Complete VPI translation is performed.

C1 C0 Action

0 0 Both incoming VPI and VCI are substituted with the VPI

and VCI, respectively, in the OAM/RM record, and the cell is routed according to the cell bus and tandem routing headers in the OAM/RM record.

0 1 The cell is not routed as OAM/RM. If the record is OAM/RM F5, the cell is translated and routed

according to the cell bus and tandem routing headers in the original VCI record. If the record is OAM/ RM F4, the cell is translated and routed according to the cell bus and tandem routing headers in the original VPI record.

1 0 The incoming VPI and VCI will be preserved, and the cell is routed according to the cell bus and tan-

dem routing headers in the OAM/RM record.

11Reserved.

Agere Systems Inc. 33

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

8.3 Look-Up Procedure

Look-up procedure is discussed in terms of 8-byte records. Differences in look-up procedures for 8-byte records and 16-byte records will be discussed in Section 8.4, Extended Records. When a cell is received, the set lutX_vpi_mask bits in the LUT X configuration structure (Table 103) indicate which incoming VPI bits are used to address the VPI record in the look-up table. The selected incoming VPI bits are concatenated and multiplied by eight (for 8-byte records) to create an offset into the table. The sum of this offset and the VPI base address, found in the LUT X configuration structure, creates the actual look-up table address for the VPI record associated with the cell. Note that only bits 3 through 18 of the VPI base address are stored in the LUT X configuration structure. If

the lutX_vpi_chk bit is set, all unused VPI bits in the cell header must be ‘0,’ or the cell will be considered out of range. If the port is configured as UNI, the upper four VPI bits (GFC field) will be ignored in the verification. When the cell is out of range, it is discarded and not counted as a received cell.

The validity of the accessed VPI record is determined by checking its active (A) and ignore (I) bits. If the cell is valid, the enable OAM/RM routing (E) bit is consulted to determine if F4 type OAM cell treatment should occur. (See the definition for these bits in Section 8.2, Organization.)

When the E bit is set and the incoming VCI is less than 32, the OAM record associated with the cell is read. To calculate the translation record address for the OAM/RM cell, the incoming VCI is multiplied by eight (for 8-byte records), and the resulting product is added to the port’s OAM base address. (See Section 8.2, Organization.) A special case exists when the incoming VCI is six and the PTI in the cell header is “110.” For this case, the OAM translation record address is the sum of the port’s OAM base address and 100h.

Next, the validity of the F4 OAM record is determined by checking its A and I bits. If it is valid, the cell is routed as described by the OAM routing control (C1, C0) bits. (See the definition for these bits in Section 8.2, Organization.)

If the E bit in the VPI record is not one or if the C1 and C0 bits in the OAM record are zero and one, respectively, the cell does not receive OAM routing. If the cell is not routed OAM, the virtual path routing bit (P bit) in the original VPI is checked to determine if the cell receives VPI only or VPI/VCI routing. If the P bit indicates VPI only routing, the cell’s VPI is replaced as indicated by the switch VPI high and low (SH, SL) bits in the VPI only translation record. (See the definition for these bits in Section 8.2, Organization.) The cell bus routing header and tandem routing header are then added to the cell, and the cell is transmitted on the cell bus.

If the P bit indicates VPI/VCI routing, the VCI translation record is accessed using the VCI offset and max VCI value bits in the VPI for VPI/VCI translation record. (The VCI offset and max VCI value bits are described in Section 8.2, Organization.) Again, the validity of the VCI translation record is determined by checking its A and I bits. Next, if the cell is valid, the E bit in the VCI record and the most significant bit of the PTI value in the cell header are

examined to determine if F5 type OAM cell treatment should occur. The value of the incoming cell’s PTI and port number determines the address in the OAM/RM record space. The following table outlines the look-up table offsets used for 8-byte records. The OAM translation record address is the sum of this offset and the port’s OAM base address.

Table 14. F5 Translation Record Addresses Table—8-Byte Records

PTI OAM Translation Offset

“100” Port’s OAM base address plus 108h “101” Port’s OAM base address plus 110h “110” Port’s OAM base address plus 118h

“111” Port’s OAM base address plus 120h

34 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Next, the validity of the F5 OAM record is determined by checking its A and I bits. If it is valid, the cell is routed as described by the OAM routing control (C1, C0) bits. (See the definition for these bits in Section 8.2, Organization.)

If the E bit in the VCI record is not one or if the C1 and C0 bits in the OAM record are zero and one, respectively, the cell does not receive OAM routing. If the cell is not routed as an OAM cell, information in the VCI translation record is used to route the cell. The cell’s VPI and VCI are replaced with the VPI and VCI, respectively, in the VCI record. The most significant 4 bits of the VPI will only be substituted if the global rplc_gfc bit in the direct configuration/control register (address 28h) is set or if the port is configured in NNI mode. The cell bus routing header and tandem routing header are then added to the cell, and the cell is transmitted on the cell bus.

Note: Unused OAM cell routing records in the LUT memory space can be used for other purposes.

Agere Systems Inc. 35

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

This look-up procedure is outlined in the flow diagram below.

5-7781F and 5-7782F

Figure 7. Translation RAM Flow Diagram

CELL IN

READ VPI

UNUSED

FROM ATM CELL

HEADER

VPI BITS ALL ‘0’

OR LUTX_VPI_CHECK

= ‘0’?

A bit = 1

AND

I bit = 0?

E bit = 1

AND

VCI < 32?

READ VP

OAM RECORD

A bit = 1

AND

I bit = 0?

C1 & C0

= “00” ?

C1 & C0

= “10” ?

P bit = 1 ?

VCI

CELL

DISCARDED

CELL

DISCARDED

YES

CELL

DISCARDED

YES

VPI/VCI

TRANSLATION;

ROUTING FROM

OAM RECORD

VPI/VCI

PRESERVED;

ROUTING FROM

OAM RECORD

VPI

TRANSLATION;

ROUTING FROM

VP RECORD

READ VPI

RECORD

VCI

READ VCI

FROM ATM CELL

HEADER

VCI IN

RANGE?

A bit = 1

AND

I bit = 0?

E bit = 1

AND

PTI[2] = ‘1’?

YES

READ VC

OAM RECORD

A bit = 1

AND

I bit = 0?

YES

CELL

DISCARDED

C1 & C0

= “00” ?

C1 & C0

= “10” ?

YES

VPI/VCI

TRANSLATION;

ROUTING FROM

OAM RECORD

VPI/VCI

PRESERVED;

ROUTING FROM

OAM RECORD

VPI/VCI

TRANSLATION;

ROUTING FROM

VC RECORD

CELL

DISCARDED

CELL

DISCARDED

YES

READ VCI

RECORD

36 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

8.4 Extended Records

The length of the translation records may be extended to 16 bytes to support two cell counts for each translation record. The lut_rec_form bits in the extended LUT configuration register (address 011Eh) are used to select this extended mode. In extended (16-byte) mode, two 32-bit counters are appended to the 8-byte records.

The first counter in the translation record, total cell count, keeps a total count of all incoming cells received from the UTOPIA bus and ultimately routed from this record. See the definition of the A and I bits in Section 8.2, Organization.

The second counter, special cell count, is a subset of the total cell count counter. This counter counts only cells whose PTI and CLP values in the cell header match the values specified in the extended LUT control register (address 0120h). For example, this counter may be used to track specific F5 type OAM/RM cells and cells indicating forward congestion (EFCI = 1) or lower priority (CLP = 1).

Agere Systems Inc. 37

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

The four translation record types for extended mode are illustrated in Figure 8 below.

Figure 8. Translation Record Types—Extended Mode

EXTENDED VPI ONLY TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A P E I VPI[11:0] +2 SH SL RESERVED +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0] +8 TOTAL CELL COUNT[31:16] +A TOTAL CELL COUNT[15:0]

+C SPECIAL CELL COUNT[31:16]

+E SPECIAL CELL COUNT[15:0]

EXTENDED VPI FOR VPI/VCI TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A P E I RESERVED +2 BITS 3 THROUGH 18 OF VCI OFFSET[15:0] +4 MAX VCI VALUE[15:0] +6 RESERVED +8 RESERVED +A RESERVED

+C RESERVED

+E RESERVED

EXTENDED VCI TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A — E I VPI[11:0]

+2 VCI[15:0] +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0] +8 TOTAL CELL COUNT[31:16] +A TOTAL CELL COUNT[15:0]

+C SPECIAL CELL COUNT[31:16]

+E SPECIAL CELL COUNT[15:0]

EXTENDED OAM/RM TRANSLATION RECORD

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 +0 A C1 C0 I VPI[11:0] +2 VCI[15:0] +4 CELL BUS ROUTING HEADER[15:0] +6 TANDEM ROUTING HEADER[15:0] +8 TOTAL CELL COUNT[31:16] +A TOTAL CELL COUNT[15:0]

+C SPECIAL CELL COUNT[31:16]

+E SPECIAL CELL COUNT[15:0]

38 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Because the translation records are larger in extended mode, the look-up table memory map changes, the translation record address calculations change, and the memory size calculations change. Figure 9 shows the new translation RAM memory map for 16-byte records when the device is configured for 16 or less PHY ports. When greater than 16 PHY ports are used, the look-up table is shared between even and odd ports. Figure 10 shows this translation RAM memory map.

Figure 9

. Translation RAM Memory Map—Extended Mode, for Up to 16 Ports

ROUTING LOOK-UP MEMORY MAP OAM CELL ROUTING PORT X RECORD MAP

0000h OAM CELL ROUTING PORT 0 +0000h VP OAM VCI = 0 (F4) 0400h OAM CELL ROUTING PORT 1 •

•

0800h OAM CELL ROUTING PORT 2

0C00h OAM CELL ROUTING PORT 3

1000h OAM CELL ROUTING PORT 4 +01F0h VP OAM VCI = 31 (F4) 1400h OAM CELL ROUTING PORT 5 +0200h V P O AM VCI = 6 & PT = “110” (F4) (RM-VPC)

1800h OAM CELL ROUTING PORT 6 +0210h VC OAM PTI = “100” (F5)

1C00h OAM CELL ROUTING PORT 7 +0220h VC OAM PTI = “101” (F5)

2000h OAM CELL ROUTING PORT 8 +0230h VC OAM PTI = “110” (F5) 2400h OAM CELL ROUTING PORT 9 +0240h VC OAM PTI = “111” (F5) 2800h OAM CELL ROUTING PORT 10 +0250h RESERVED

2C00h OAM CELL ROUTING PORT 11 +0260h RESERVED

3000h OAM CELL ROUTING PORT 12 •

•

3400h OAM CELL ROUTING PORT 13 3800h OAM CELL ROUTING PORT 14

3C00h OAM CELL ROUTING PORT 15 +03F0h RESERVED

4000h

ANY PURPOSE LOOK-UP MEMORY

SHARED BETWEEN EACH OF THE

16 PORTS

7FFFFh

Agere Systems Inc. 39

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

Figure 10

. Translation RAM Memory Map—Extended Mode, for Greater than 16 Ports

The OAM/RM translation records at the bottom of the memory map now use 16 Kbytes of memory when the device is configured to support 16 to 32 MPHY ports, and the base addresses for the OAM records are now calculated using the following equation for 16 or less ports:

OBA = PN × 16 × 64 In this equation, OBA is the OAM base address, PN is the port number (for up to 16 ports), 16 is the number of

bytes per record, and 64 is the number of records per port. For 16-byte records, when greater than 16 ports are used, the base addresses of the OAM records are calculated

from the following equation: OBA = INT(PN/2) ×

16 × 64

In this equation, OBA is the OAM base address, PN is the port number (for greater than 16 ports), 16 is the number of bytes per record, and 64 is the number of records per port. The INT function specifies that the term within the parentheses is an integer, i.e., the fractional part is discarded.

ROUTING LOOK-UP MEMOR Y MAP OAM CELL ROUTING PORT X RECORD MAP

0000h OAM CELL ROUTING PORT 0 AND 1 +0000h VP OAM VCI = 0 (F4) 0400h OAM CELL ROUTING PORT 2 AND 3 •

•

0800h OAM CELL ROUTING PORT 4 AND 5

0C00h OAM CELL ROUTING PORT 6 AND 7

1000h OAM CELL ROUTING PORT 8 AND 9 +01F0h VP OAM VCI = 31 (F4) 1400h OAM CELL ROUTING PORT 10 AND 11 +0200h VP OAM VCI = 6 & PT = “110” (F4) (RM-VPC)

1800h OAM CELL ROUTING PORT 12 AND 13 +0210h VC OAM PTI = “100” (F5)

1C00h OAM CELL ROUTING PORT 14 AND 15 +0220h VC OAM PTI = “101” (F5)

2000h OAM CELL ROUTING PORT 16 AND 17 +0230h VC OAM PTI = “110” (F5) 2400h OAM CELL ROUTING PORT 18 AND 19 +0240h VC OAM PTI = “111” (F5) 2800h OAM CELL ROUTING PORT 20 AND 21 +0250h RESERVED

2C00h OAM CELL ROUTING PORT 22 AND 23 +0260h RESERVED

3000h OAM CELL ROUTING PORT 24 AND 25 •

•

3400h OAM CELL ROUTING PORT 26 AND 27 3800h OAM CELL ROUTING PORT 28 AND 29

3C00h OAM CELL ROUTING PORT 30 AND 31 +03F0h RESERVED

4000h

ANY PURPOSE LOOK-UP MEM O RY

SHARED BETWEEN EACH OF THE

16 PAIRS OF PORTS

7FFFFh

40 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

To calculate the 16-byte translation record address for the F4 type OAM cell, the incoming VCI is multiplied by 16,

and the resulting product is added to the port’s OAM base address. For the special case when the incoming VCI is six and the PTI in the cell header is “110,” the OAM translation record address is the sum of the port’s OAM base address and 200h.

The 16-byte OAM type F5 translation record offset is determined from the incoming cell’s PTI using the following table. The OAM translation record address is the sum of this offset and the port’s OAM base address.

Table 15. F5 Translation Record Addresses Table—Extended Mode

In extended mode, the memory space used by the VPI records also changes. The total memory now used by the VPI records is calculated using the following equation for 16 or less ports:

MS = NP x 2

x 16

In this equation, MS is the memory size used for VPI records, NP is the number of ports used, 16 is the number of bytes per record, and NB is the number of incoming VPI bits used to address the look-up table.

For 16-byte records, when greater than 16 ports are used, the total memory used by the VPI records is calculated using the following equation:

MS = INT(NP/2) x 2

x 16

In this equation, MS is the memory size used for VPI records, NP is the number of ports used (for greater than 16 ports), 8 is the number of bytes per record, and NB is the number of incoming VPI bits used to address the lookup table. The INT function specifies that the term within the parentheses is an integer, i.e., the fractional part is discarded.

To address the 16-byte VPI translation record, the selected incoming VPI bits (see Section 8.3, Look-Up Procedure) are concatenated and multiplied by 16 to create an offset into the look-up table. The sum of this offset and the VPI base address creates the actual VPI translation record address associated with the incoming cell. Note that only bits 3 through 18 of the VPI base address are stored

in the LUT X configuration structure.

To address the 16-byte VCI translation record, the VCI from the cell’s header is multiplied by 16 and added to bits 3 through 18 of the VCI offset which is obtained from the VPI record. This sum is the final offset into the look-up table. This final offset should then be added to the translation RAM memory beginning address 100000h (Table 125) to obtain the final address.

PTI OAM Translation Offset

“100” Port’s OAM base address plus 210h “101” Port’s OAM base address plus 220h

“110” Port’s OAM base address plus 230h “111” Port’s OAM base address plus 240h

Agere Systems Inc. 41

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

8 Look-Up Table (continued)

8.5 Diagnostics

The T8207 also includes diagnostics to track misrouted cells. A cell is considered misrouted if its A and I bits are

“00,” if its VCI is out of range, or if the lutX_vpi_chk bit is ‘1’ and the unused VPI bits in the incoming cell header are not all zero (see Section 8.3, Look-Up Procedure). When a misrouted cell is detected, the misrouted cell header high and low registers (addresses 0146h and 0148h) may be updated. If enabled, the mis_cell interrupt, the vci_or interrupt, or the vpi_or interrupt will be generated as appropriate (see Table 79 in Section 14.3, Extended Memory Registers).

The misrouted cell header high and low registers contain the first four header bytes of selected misrouted cells. Only a misrouted cell from a port whose mis_cell_lut_sel bit is set will update these registers, and this misrouted cell will update the registers only if it is the first received after the mis_cell_clr bit is set. The lst_mis_cell_lut bits indicate the port from which the header bytes in the misrouted cell header high and low registers were received. The mis_cell_lut_sel bits are located in the misrouted LUT 1 register (address 0142h). The mis_cell_clr, mis_cell_latch, and lst_mis_cell_lut bits are located in the misrouted LUT 2 register (address 0144h). (See Tables 70 and 71 in Section 14.3, Extended Memory Registers, for a complete description of the above bits.)

8.6 Setup

When configuring the lut_en bits in the LUT X configuration/status register (addresses 0320h through 033Eh), care

must be taken to ensure that the enabled ports’ LUTs correspond to the ports chosen in UTOPIA mode. (See Section 9.6, UTOPIA Pin Modes.) If a LUT is not enabled, corresponding bits in the LUT X configuration structure (Section 14.3.2.3, RX UTOPIA Monitoring, Table 103) will be ignored. Also, when the device is configured for UTOPIA PHY mode (see Section 9, UTOPIA Interfa ce), only port 0 entries in the external RAM look-up table are used; therefore, the look-up table should be set up accordingly.

42 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface

The

CelXpres

T8207 supports the ATM Forum’s UTOPIA level 1 and level 2 specifications for cell-level handshake

and MPHY operation with rates up to 353 Mbits/s. The device may be configured as an ATM layer or as a PHY layer by programming the phyen* bit in the main configuration 1 register (address 0100h).

As an ATM layer, the device may interface with a single PHY layer or multiple PHY layers (up to 32). Also as an A TM layer , it may be configured for shared UTOPIA mode if 16 or less PHYs are used. (Note that if shared UTOPIA mode is not used, the slave_en bit in the main configuration/control register (address 0110h) must be cleared at device setup.)

In PHY mode, the T8207 functions as a single PHY device on the UTOPIA bus or as one of 31 PHY devices on the UTOPIA level two bus.

In addition to the required UTOPIA signals, the T8207 supports an additional three transmit and three receive enable (u_txenb*[3:1] and u_rxenb*[3:1]) signals, an additional three transmit and three receive cell available (u_txclav[3:1] and u_rxclav[3:1]) signals, a transmit parity (u_txprty) signal, and a receive parity (u_rxprty) signal.

The T8207 UTOPIA signal names begin with u_tx, for UTOPIA transmit, or u_rx, for UTOPIA receive. References to transmit or receive are made relative to the UTOPIA data flow for the A TM layer UTOPIA interface. Therefore, signals starting with u_rx, such as u_rxenb*[3:0] and u_rxdata[7:0], are receive UTOPIA signals for devices in ATM mode but are transmit UTOPIA signals for devices in PHY mode. Furthermore, signals such as u_txclav[3:0] and u_txaddr[4:0] are transmit UTOPIA signals for devices in ATM mode but are receive UTOPIA signals for devices in PHY mode. The above ATM to PHY terminology will be used throughout this UTOPIA Interface section.

Agere Systems Inc. 43

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.1 Incoming UTOPIA Cell Interface

9.1.1 Incoming PHY Mode (Cells Received by T8207)

In PHY mode, only one enable (u_rxenb*[0]) signal and one cell available (u_rxclav[0]) signal are used. The

u_rxenb*[0] signal is an input connected to the ATM layer’s TxEnb* signal, and the u_rxclav[0] signal is an output connected to the ATM layer’s TxClav signal. As a PHY device, the T8207 uses only the LUT 0 configuration/status register (address 0320h) and LUT 0 configuration 1 registers (addresses 0704h—0706h). For UTOPIA level 2 functionality, the PHY address is programmed in the addr_match bits of the UTOPIA configuration register (address 0114h), and the addr_clav_en bits of the main configuration 2 register (address 0112h) can be programmed to any value mentioned in the register except “000.” As specified in the UTOPIA level 2 specification, during the polling process, the T8207 drives the u_rxclav[0] signal during the clock cycle following the cycle in which its address appears on the u_rxaddr pins. The u_rxclav[0] pin goes high impedance when not selected to support MPHY operation. In UTOPIA level 1, the above level 2 bits are not meaningful; therefore, the addr_clav_en bits must be programmed to “000,” the u_rxaddr pins must be grounded, and the addr_match bits cleared.

When the T8207 device is in PHY mode, if bit 5 (dont_inhibit_rxphy_clav) of register 0112h is cleared to ‘0,’ the

rx_clav signal is deasserted if the RX UTOPIA FIFO is considered full. If this bit is set to

‘1,’ the T8207 keeps

the rx_clav signal always asserted high indicating the capability to accept cells even if the RX UTOPIA FIFO could overrun, or is actually overrun.

9.1.2 Incoming ATM Mode (Cells Received by T8207)

In ATM mode, the T8207 may connect to PHY devices that either meet level 1 or level 2 UTOPIA specifications. If the connection is to devices that meet only UTOPIA level 1 specifications, the T8207 may access up to four of these PHY devices using the four enable (u_rxenb*[3:0]) and cell available (u_rxclav[3:0]) signals. Connection to more than one PHY device is possible only if the PHY’s data, start of cell, and parity outputs go high impedance when the device is not enabled. Polling of the cell available signals usually occurs while the current cell is received.

If the T8207 connects to PHY devices meeting level 2 UTOPIA specifications, one RxCLAV/RxENB pair supports up to 16 PHY ports. For 32 PHY ports, two RxCLAV/RxENB pairs support two groups of 16 PHY ports for a total of 32 PHY ports. In ATM MPHY mode, the u_rxdata[7:0], u_rxaddr[4:0], u_rxsoc, and u_rxprty signals are connected to each PHY port. In addition, the T8207 generates the address (u_rxaddr[4:0]) signals, permitting selection and arbitration among the MPHY ports. The number of address lines used in the connection may vary from one to four, giving a maximum address value of 15. (All five address lines must be connected to provide for the NULL address.) Refer to Section 9.6, UTOPIA Pin Modes, for more information about the possible combinations of address, cell available, and enable signals. The UTOPIA specification for operation with one TxClav and one RxClav is used when the T8207 connects to multiple level 2 PHY devices.

Whether the T8207 is connected to several level 1 or level 2 PHY devices, a round-robin algorithm is implemented that ensures that all PHY devices are serviced (accessed) in a timely manner. In addition, the number of clock cycles wasted for bus arbitration is minimized because polling is performed during cell transfer.

In ATM mode, all unused u_rxclav inputs require connection to ground. Note: The u_rxenb outputs are high impedance during powerup and reset. An attached PHY may interpret this

high-impedance state as an enable; however, the T8207 is not ready to properly handle input data during this time. Attach pull-up resistors to these outputs if a problem is anticipated.

When the T8207 is in ATM mode, if bit 6 (inhibit_rxuto_fifo_overrun) of register 0112h is set to ‘1,’ the T8207 prevents the RX UTOPIA FIFO from overflowing by deasserting its rx_enb* signal even though the rx_clav signal is high when polled, if the RX UTOPIA FIFO is considered full. If this bit is cleared to ‘0,’ the rx_enb* signal is not

deasserted even if the RX UTOPIA FIFO is considered full.

44 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.2 Outgoing UTOPIA Cell Interface

9.2.1 Outgoing PHY Mode (Cells Sent by T8207)

In PHY mode, only one enable (u_txenb*[0]) signal and one cell available (u_txclav[0]) signal are used. The

u_txenb*[0] signal is an input connected to the ATM layer’s RxEnb* signal, and the u_txclav[0] signal is an output connected to the ATM layer’s RxClav signal. As a PHY device, the T8207 may use queue group 0 (queues 0, 1, 2, and 3) in the SDRAM and TX UTOPIA cell buffer. The div_queue bits in the main configuration 2 register (address 0112h) may be programmed to “000” for 4 queues or “101” for 1 queue, and the port_rte[63:0] bits in the TX PHY FIFO routing 0, 1, 2, and 3 registers (addresses 017Ch, 017Eh, 017Ah, and 0178h respectively) must be programmed to zero. If only queue 0 is used, configure and use only the queue 0 registers at addresses 0440h and 2000h through 2016h. Also, if only queue 0 is used, program the mphy_select bits and priority_select bits in the routing information 1, 2, and 3 registers addresses 0200h, 0202h, and 0204h to the zero value of “110000.” If queues 0, 1, 2, and 3 are used, configure and use only the queue 0, 1, 2, and 3 registers at addresses 0440h through 0446h and 2000h through 2076h. Also, if queues 0, 1, 2, and 3 are used, only the mphy_select bits in the routing information 1 and 2 registers (addresses 0200h and 0202h) must all be programmed to the zero value of “110000.”

For UTOPIA level 2 functionality, the PHY address is programmed in the addr_match bits of UTOPIA configuration register (address 0114h), and the addr_clav_en bits of the main configuration 2 register (address 0112h)

can be

programmed to any value mentioned in the register except “000.”

As specified in the UT OPI A level 2 spec ifica tio n, the T8207 drives the u_txclav[0] signal during the clock cycle following the one with its address on the u_txaddr pins. The u_txclav[0] pin goes high impedance when not selected to support MPHY operation. When the tx_utopia_hi_z bit in the main configuration 1 register (address 0100h) is cleared, the u_txsoc, u_txdata[7:0] and u_txprty outputs go high impedance when not selected, allowing multiple PHYs to be connected on the same UTOPIA bus. In UTOPIA level 1, the above level 2 bits are not meaningful; therefore, the addr_clav_en bits must be

programmed to “000,” the u_txaddr pins must be grounded, and the addr_match bits cleared.

Note: If the SDRAM is bypassed, the T8207 uses only queue 0 in the TX UTOPIA cell buffer. Note: Even though the outgoing (egress) queues are 0—3, the egress port is determined by the address match

bits in register 0114h.

Agere Systems Inc. 45

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.2.2 Outgoing ATM Mode (Cells Sent by T8207)

In ATM mode, the T8207 may connect to PHY devices that either meet level 1 or level 2 UTOPIA specifications. If connection is to devices that meet only UTOPIA level 1 specifications, the T8207 may access up to four of these PHY devices using the four enable (u_txenb*[3:0]) and cell available (u_txclav[3:0]) signals. Polling of the cell available signals occurs while the current cell is transmitted.

If the T8207 connects to PHY devices meeting level 2 UTOPIA specifications, one TxCLAV/TxENB pair supports up to 16 PHY ports. For 32 PHY ports, two TxCLAV/TxENB pairs support two groups of 16 PHY ports for a total of 32 PHY ports.

In ATM MPHY mode, the u_txdata[7:0], u_txaddr[4:0], u_txsoc, and u_txprty outputs are connected to each PHY port. In addition, the T8207 generates the address (u_txaddr[4:0]) signals, permitting selection and arbitration among the ports. The number of address lines used in the connection may vary from one to four giving a maximum address value of 15. (All five address lines must be connected to provide for the NULL address.) Refer to Section

9.6, UTOPIA Pin Modes, for more information about the possible combinations of address, cell available, and enable signals. The UTOPIA specification for operation with one TxClav and one RxClav is used when the T8207 connects to multiple UTOPIA level 2 PHY devices.

In ATM mode, all unused u_txclav inputs require connection to ground. Note: The u_txenb outputs are high impedance during powerup and reset. An attached PHY may interpret this

high-impedance state as an enable; however, the T8207 is not ready to send data during this time. Attach pull-up resistors to these outputs if a problem is anticipated.

The TX UTOPIA cell buffer holds the next cells to be transmitted onto the UTOPIA bus. This TX UTOPIA cell buffer, which holds 128 cells, may be divided into 1, 4, 8, 16, 32, or 64 queues using the div_queue bits in the main configuration 2 register (address 0112h). The number of ports that the T8207 supports determines the number of queues that should be chosen. (See Section 9.6, UTOPIA Pin Modes.) The number of cells per queue, held by the buffer, is determined by dividing 128 (maximum number of cells that TX UTOPIA cell buffer holds) by the number of queues selected (e.g., two cells per queue for 64 queues and 32 cells per queue for 4 queues).

If the T8207_sel bit in the main configuration 2 register, Table 59, is set, each port is assigned four queues in the TX UTOPIA cell buffer except in the case of 32 ports. For 32 ports, each port is assigned two queues. Each group of four queues is priority encoded where the lowest-numbered queue has the highest priority. Groups of four queues are shared among two ports as follows:

■ Queues 0—3 are shared between ports 0 and 1.

■ Queues 4—7 are shared between ports 2 and 3.

■ Queues 8—11 are shared between ports 4 and 5.

■ Queues 12—15 are shared between ports 6 and 7.

■ Queues 16—19 are shared between ports 8 and 9.

■ Queues 20—23 are shared between ports 10 and 11.

■ Queues 24—27 are shared between ports 12 and 13.

■ Queues 28—31 are shared between ports 14 and 15.

■ Queues 32—35 are shared between ports 16 and 17.

■ Queues 36—39 are shared between ports 18 and 19.

■ Queues 40—43 are shared between ports 20 and 21.

■ Queues 44—47 are shared between ports 22 and 23.

■ Queues 48—51 are shared between ports 24 and 25.

■ Queues 52—55 are shared between ports 26 and 27.

■ Queues 56—59 are shared between ports 28 and 29.

■ Queues 60—63 are shared between ports 30 and 31.

46 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

If the T8207_sel bit is set and 16 or less ports are used, then each port uses four queues with priorities from 0 to 3, where 0 is the highest priority and 3 is the lowest priority. The lowest-numbered queue in the group of four is assigned priority 0, and the highest-numbered queue in the group is assigned priority 3. For 32 PHY ports, any of the four queues in each group may be assigned to either the even- or odd-numbered port. An example, which will be called

normal 32-port mode, assigns queues with priorities of 0 and 2 to the even-numbered ports and queues with priorities of 1 and 3 to the odd-numbered ports. See the port_rte[63:48], port_rte[47:32], port_rte[31:16] and port_rte[15:0] bits in the TX PHY FIFO routing 3, 2, 0, and 1 (addresses 0178h, 017Ah, 017Ch, and 017Eh) registers, respectively. Figure 1 1 illustrates the selection of ports when 32 are used.

If the T8207_sel bit in the main configuration 2 register (Table ) is cleared, the device cannot be configured to access 32 PHY ports. Only 16 PHYs and 32 queues are available. For 16 PHY ports, any of the four queues in each group may be assigned to either the even- or odd-numbered port. An example, which will be called normal 16-port mode, assigns queues with priorities of 0 and 2 to the even-numbered ports and queues with priorities of 1 and 3 to the odd-numbered ports.

5-7784.b F

Figure 11. Queue Priority Multiplexing

The TX UTOPIA cell buffer is kept full by cells transferred to it from the SDRAM. Each port has equal priority for transmitting onto the UTOPIA bus. The cell transmitted by any one port is determined by the priority of its queues with cells waiting to be transmitted. In addition, the number of clock cycles wasted for bus arbitration is minimized because polling is performed during cell transfer.

Cells arriving from the cell bus have their header error check (HEC) bytes removed. Therefore, the T8207 calculates the HEC and inserts it into each cell before transmitting it onto the UTOPIA bus. See Figure 12.

9.3 Counters

For each port selected in MPHY mode, two 16-bit registers (in_cnt_phyX[31:16] and in_cnt_phyX[15:0] in Table

102) are used as a 32-bit free-running incoming cell counter. Each port’s counter counts valid and misrouted incoming cells. Incoming cells are not counted if they encounter an ignore (I) bit in their translation records that is

‘1’ or if their VPI and/or VCI are out of range. The counter for port 0 is found at addresses 0700h and 0702h. See Table 102 in Section 14.3.2.3, RX UTOPIA Monitoring, for the addresses of other ports' incoming cell counters.

Also, for each port selected in MPHY mode, two 16-bit registers (out_cnt_phyX[31:16] and out_cnt_phyX[15:0] in Table 101) are used as a 32-bit free-running outgoing cell counter. Each port's counter counts all outgoing cells to the UTOPIA bus. The counter for port 0 is found at addresses 0600h and 0602h. See Table 101 in Section

14.3.2.2, TX UTOPIA Monitoring, for the addresses of other ports' outgoing cell counters.

CELL BUS

128

CELL

FIFO

QUEUE 0 QUEUE 1 QUEUE 2 QUEUE 3

P0 P1 P2 P3 P4 P5 P6 P7 P8 P9

P10

P30 P31

TX UTOPIA PORT

PRIORITY

DEMULTIPLEXER CONTROLLED BY

PORT_RTE[63:48], PORT_RTE[47:32],

PORT_RTE[31:16], PORT_RTE[15:0]

IN TX PHY FIFO ROUTING 3, 2, 0, AND 1 REGISTERS

(ADDRESSES 0178h, 017Ah, 017Ch, 017Eh)

QUEUE 60 QUEUE 61 QUEUE 62 QUEUE 63

Agere Systems Inc. 47

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.4 55-Byte UTOPIA Mode

In this special UTOPIA mode, the T8207 transmits a 55-byte cell, as opposed to 53 bytes, on the UTOPIA bus. The extra 2 bytes are the tandem routing header received with the cell from the cell bus. These 2 bytes are appended to the beginning of the cell with the tandem routing header [15:8] byte first, followed by the tandem routing header [7:0] byte. Clearing the sp_utopia_sel* bit in the main configuration 1 register (address 0100h) enables this mode. The start of cell signal (u_txsoc) is asserted only once with the first tandem routing header byte. The T8207 may be configured for 55-byte UTOPIA mode whether it is an ATM or PHY device.

5-7783aF

Figure 12. TX UTOPIA Cell Handling

EXTERNAL

SDRAM

CONTROLLER

QUEUE FILL

MANAGER

EFCI

INSERTION

FECN ENA

QUEUE 0

TX UTOPIA

CELL BUFFER

(2 CELLS)

QUEUE 1

TX UTOPIA

CELL BUFFER

(2 CELLS)

QUEUE 62

TX UTOPIA

CELL BUFFER

(2 CELLS) QUEUE 63

TX UTOPIA

CELL BUFFER

(2 CELLS)

HEC

INSERTION

53-byte CELL TO TX UTOPIA

48 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.5 Shared UTOPIA Mode

The shared UTOPIA mode supports up to 16 PHY ports using only 32 queues, and it allows two T8207 devices on different cell buses to share the same UTOPIA bus. This shared mode can be used to provide redundancy or to increase the cell bus system capacity. One T8207 device is configured as master and the other as slave, using the slave_en bit in the main configuration/control register (address 0110h). The master and the slave communicate to each other through the shared UTOPIA output (u_shr_o) and input (u_shr_i) pins. For the master, u_shr_o functions as the grant output, and u_shr_i, as the request input. For the slave, u_shr_o functions as the request output, and u_shr_i, as the grant input. Only T8207 devices configured for ATM mode may be used in shared UTOPIA mode. This configuration is supported for both UTOPIA level 1 and 2 configurations. The configuration for the addr_clav_en bits must be the same in both devices in MCF2 (0112h) and port_rte (0178h to 017Eh) registers.

Note: The T8207 will support shared UTOPIA mode for only up to 32 queues. T o use shared UTOPIA with 16 PHY

ports, only 32 queues, shared between even and odd ports can be used, which translates to a zero value for the T8207_sel bit (Table 59).

The TX UTOPIA cell buffers in the master and the slave may be divided into the same number of queues or different number of queues. The mast_queue_in[31:16], mast_queue_in[15:0], slav_queue_in[31:16], and slav_queue_in[15:0] bits in the master queue 0 (address 015Ch), master queue 1 (address 015Eh), slave queue 0 (address 016Ch), and slave queue 1 (address 016Eh) registers, respectively, must be configured in the master

device. These bits indicate which queues in the master and which queues in the slave are enabled. The master’s priority algorithm uses this information to determine which waiting cell should be transmitted. The slave queue 0 and 1 registers are ignored in the slave.

The transmit operation in shared UTOPIA mode is illustrated in Figure 13. For the transmit interface, all enable, start of cell, and data signals occur relative to the low-going start of grant signal from the master. The start of grant signal occurs every 60 clock cycles and is always preceded by at least six clock cycles of ones.

Both devices transmit on the TX UTOPIA bus; the master arbitrates the bus and grants the slave access via its u_shr_o pin. When the slave has cells waiting for transmission, it makes a request for each queue (up to 32) that contains cells. To make this request, the slave pulls its request output low for one clock cycle during the queue’s request period. The request period for each queue is assigned relative to the master’s start of grant signal. The request period for queue zero occurs ten clock cycles after the start of grant and is followed by the request period for queue one. The master uses the received queue number and a priority algorithm to determine if a slave’s cell should be transmitted before one of its own. Both master and slave have an equal chance to transmit cells if the cells have equal priority. The master grants the slave’s request by sending 8 bits of serial data, clocked at the rate of the UTOPIA transmit clock, to its grant output. The first bit is the low-going grant signal. The next 5 bits designate the queue number of the cell to be transmitted. The queue number is sent most significant bit first. The next bit is the valid bit; it is low if this grant is valid. Finally, the last bit (R[0]) is reserved for future use. The slave then has 53 cycles or 55 cycles to transmit its cell depending on the mode.

In UTOPIA receive mode, the master controls the UTOPIA bus, and the slave only monitors the bus. Both master and slave receive all cells and use their individual look-up tables to determine which cells are destined for their cell bus. The master controls the enable (u_rxenb[3:0]) and address (u_rxaddr[4:0]) signals to the UTOPIA bus. The slave monitors these signals to determine when the cell starts and which port is sending the cell.

In shared UTOPIA mode, the master always drives the u_rxaddr[4:0], u_txaddr[4:0], u_txsoc, u_rxenb*[3:0], and u_txenb*[3:0] signals. These signals become high impedance on the slave when the slave_en bit in the main configuration/control register (address 0110h) is set. Both the master and slave drive the u_txprty and u_txdata[7:0] signals when they transmit a cell; therefore, these signals must transition to a high-impedance state when not active. Clear the tx_utopia_hi_z bit in the main configuration 1 register (address 0100h) to force the u_txprty and u_txdata[7:0] signals to a high-impedance state when inactive.

Agere Systems Inc. 49

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

5-7786aF

Figure 13. TX UTOPIA Bus Sharing

XH0H1H2 P46P47P44 P46 P47P45

QS[3]

VALID

QS[4] QS[2] QS[1] QS[0] R[0]

INVALID INVALIDQR0 QR1 QR2

U_TXCLK

U_TXENB

U_TXSOC

U_TXDATA[7:0]

U_TXPRTY

GRANT

REQUEST

50 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.6 UTOPIA Pin Modes

In multi-PHY mode, the T8207 interfaces with up to 32 PHY ports. Each port is numbered and accessed using a certain combination of the cell available/enable (Clav/Enb*) and address (Addr) signals. The addr_clav_en bits in the main configuration 2 register (address 0112h) are used to select this combination of cell available/enable and address signals. Table 16 indicates the port numbering for each of the possible configurations.

The first selection of zero address and four cell available/enable signals (a value of

“000”

in bits 2:0 of register 0112h) is used for connection to UTOPIA level one devices. Use this selection to connect from one to four PHY devices to the T8207 in ATM mode. If only one PHY is connected, any of the four cell available signals may be connected to the PHY . For two PHY devices, connect any two (internal port number must be matched to the clav being used). All unused u_rxclav inputs require connection to ground. Four queues are allocated per PHY in this configuration.

The second selection of one address and four cell available/enable signals (a value of

“010”

in bits 2:0 of register 0112h) is used for connection to UTOPIA level two devices. The selection may be used for up to four PHY groups of two ports each. (See Appendix 1 of The ATM Forum Technical Committee UTOPIA Level 2, Version 1.0 specification.) All unused u_rxclav inputs require connection to ground. Four queues are allocated per PHY in this configuration.

The third selection of two address and four cell available/enable signals (a value of

“101”

in bits 2:0 of register 01 12h) is used for connection to four UTOPIA level 2 PHY groups of four ports each. If the T8207_sel bit in register 01 12h is set, four queues are allocated per PHY. If the T8207_sel bit is cleared, two queues are allocated per PHY if the

normal

16-port mode described in Section 11.4, Queuing is used or a programmable number of queues can

be allocated per PHY based on the settings in registers 017Ch—017Eh. The fourth selection of two address and two cell available/enable signals (a value of “100” in bits 2:0 of register

0112h) is used for connection to two UTOPIA level 2 PHY groups of four ports each. All unused u_rxclav inputs require connection to ground. Four queues are allocated per PHY in this configuration.

The fifth selection of three address and two cell available/enable signals (a value of

“111”

in bits 2:0 of register 0112h) is used for connection to two UTOPIA level 2 PHY groups of eight ports each. All unused u_rxclav inputs require connection to ground. If the T8207_sel bit in register 0112h is set, four queues are allocated per PHY. If the T8207_sel bit is cleared, two queues are allocated per PHY if the

normal

16-port mode described in Section 11.4,

Queuing is used or a programmable number of queues can be allocated per PHY based on the settings in registers

017Ch—017Eh. The sixth selection of three address and one cell available/enable signals (a value of “110” in bits 2:0 of register

0112h) is used for connection to eight UTOPIA level 2 PHY ports. All unused u_rxclav inputs require connection to ground. Four queues are allocated per PHY in this configuration.

The seventh selection of four address and one cell available/enable signals (a value of

“001”

in bits 2:0 of register 0112h) is used for connection to sixteen UTOPIA level 2 PHY ports. All unused u_rxclav inputs require connection to ground. If the T8207_sel bit in register 0112h is set, four queues are allocated per PHY. If the T8207_sel bit is cleared, two queues are allocated per PHY if the normal 16-port mode described in Section 11.4, Queuing is used

or a programmable number of queues can be allocated per PHY based on the settings in registers 017Ch—017Eh. Finally, the eighth selection of four address and two cell available/enable signals (a value of “011” in bits 2:0 of reg-

ister 0112h) is used for connection to two UTOPIA Level 2 PHY groups of 16 ports each. All unused u_rxclav inputs require connection to ground. The T8207_sel bit in register 0112h must be set to ‘1’ for this mode. Two queues are

allocated per PHY, if the normal 32-port mode described in Section 11.4, Queuing is used or a programmable number of queues can be allocated per PHY based on the settings in registers 0178h—017Eh.

Agere Systems Inc. 51

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

Table 16. Port Numbering for MPHY Configurations

# of

addr

# of

clav/enb*

Ports 0—7

Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7

0 4 enb*[0],

clav[0],

addr = 0

— enb*[1],

clav[1],

addr = 0

— enb*[2],

clav[2],

addr = 0

— enb*[3],

clav[3],

addr = 0

—

1 4 enb*[0],

clav[0],

addr = 0

— enb*[0],

clav[0],

addr = 2

— enb*[1],

clav[1],

addr = 0

— enb*[1],

clav[1],

addr = 2

—

2 4 enb*[0],

clav[0],

addr = 0

enb*[0],

clav[0],

addr = 1

enb*[0],

clav[0],

addr = 2

enb*[0],

clav[0],

addr = 3

enb*[1],

clav[1],

addr0

enb*[1],

clav[1],

addr = 1

enb*[1],

clav[1],

addr = 2

enb*[1],

clav[1],

addr = 3

2 2 enb*[0],

clav[0],

addr = 0

— enb*[0],

clav[0],

addr = 2

— enb*[0],

clav[0],

addr = 4

— enb*[0],

clav[0],

addr = 6

—

3 2 enb*[0],

clav[0],

addr = 0

enb*[0],

clav[0],

addr = 1

enb*[0],

clav[0],

addr = 2

enb*[0],

clav[0],

addr = 3

enb*[0],

clav[0],

addr = 4

enb*[0],

clav[0],

addr = 5

enb*[0],

clav[0],

addr = 6

enb*[0],

clav[0],

addr = 7

3 1 enb*[0],

clav[0],

addr = 0

— enb*[0],

clav[0],

addr = 2

— enb*[0],

clav[0],

addr = 4

— enb*[0],

clav[0],

addr = 6

—

4 1 enb*[0],

clav[0],

addr = 0

enb*[0],

clav[0],

addr = 1

enb*[0],

clav[0],

addr = 2

enb*[0],

clav[0],

addr = 3

enb*[0],

clav[0],

addr = 4

enb*[0],

clav[0],

addr = 5

enb*[0],

clav[0],

addr = 6

enb*[0],

clav[0],

addr = 7

4 2 enb*[0],

clav[0],

addr = 0

enb*[0],

clav[0],

addr = 1

enb*[0],

clav[0],

addr = 2

enb*[0],

clav[0],

addr = 3

enb*[0],

clav[0],

addr = 4

enb*[0],

clav[0],

addr = 5

enb*[0],

clav[0],

addr = 6

enb*[0],

clav[0],

addr = 7

# of

addr

# of

clav/enb*

Ports 8—15

Port 8 Port 9 Port 10 Port 11 Port 12 Port 13 Port 14 Port 15

04 ———————— 1 4 enb*[2],

clav[2],

addr = 0

— enb*[2],

clav[2],

addr = 2

— enb*[3],

clav[3],

addr = 0

— enb*[3],

clav[3],

addr = 2

—

2 4 enb*[2],

clav[2],

addr = 0

enb*[2],

clav[2],

addr = 1

enb*[2],

clav[2],

addr = 2

enb*[2],

clav[2],

addr = 3

enb*[3],

clav[3],

addr = 0

enb*[3],

clav[3],

addr = 1

enb*[3],

clav[3],

addr = 2

enb*[3],

clav[3],

addr = 3

2 2 enb*[1],

clav[1],

addr = 0

— enb*[1],

clav[1],

addr = 2

— enb*[1],

clav[1],

addr = 4

— enb*[1],

clav[1],

addr = 6

—

3 2 enb*[1],

clav[1],

addr = 0

enb*[1],

clav[1],

addr = 1

enb*[1],

clav[1],

addr = 2

enb*[1],

clav[1],

addr = 3

enb*[1],

clav[1],

addr = 4

enb*[1],

clav[1],

addr = 5

enb*[1],

clav[1],

addr = 6

enb*[1],

clav[1],

addr = 7

3 1 enb*[0],

clav[0],

addr = 8

— enb*[0],

clav[0],

addr = 10

— enb*[0],

clav[0],

addr = 12

— enb*[0],

clav[0],

addr = 14

—

4 1 enb*[0],

clav[0],

addr = 8

enb*[0],

clav[0],

addr = 9

enb*[0],

clav[0],

addr = 10

enb*[0],

clav[0],

addr = 11

enb*[0],

clav[0],

addr = 12

enb*[0],

clav[0],

addr = 13

enb*[0],

clav[0],

addr = 14

enb*[0],

clav[0],

addr = 15

4 2 enb*[0],

clav[0],

addr = 8

enb*[0],

clav[0],

addr = 9

enb*[0],

clav[0],

addr = 10

enb*[0],

clav[0],

addr = 11

enb*[0],

clav[0],

addr = 12

enb*[0],

clav[0],

addr = 13

enb*[0],

clav[0],

addr = 14

enb*[0],

clav[0],

addr = 15

52 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

Table 16. Port Numbering for MPHY Configurations (continued)

# of

addr

# of

clav/enb*

Ports 16—23

Port 16 Port 17 Port 18 Port 19 Port 20 Port 21 Port 22 Port 23

04 ———————— 14 ———————— 24 ———————— 22 ———————— 32 ———————— 31 ———————— 41 ———————— 4 2 enb*[1],

clav[1],

addr = 0

enb*[1],

clav[1],

addr = 1

enb*[1],

clav[1],

addr = 2

enb*[1],

clav[1],

addr = 3

enb*[1],

clav[1],

addr = 4

enb*[1],

clav[1],

addr = 5

enb*[1],

clav[1],

addr = 6

enb*[1],

clav[1],

addr = 7

# of

addr

# of

clav/enb*

Ports 24—31

Port 24 Port 25 Port 26 Port 27 Port 28 Port 29 Port 30 Port 31

clav[1],

addr = 8

enb*[1],

clav[1],

addr = 9

enb*[1],

clav[1],

addr = 10

enb*[1],

clav[1],

addr = 11

enb*[1],

clav[1],

addr = 12

enb*[1],

clav[1],

addr = 13

enb*[1],

clav[1],

addr = 14

enb*[1],

clav[1],

addr = 15

Agere Systems Inc. 53

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

9 UTOPIA Interface (continued)

9.7 UTOPIA Clocking

All TX UTOPIA signals in the T8207 are clocked on the rising edge of the TX UTOPIA clock, and all RX UTOPIA signals are clocked on the rising edge of the RX UTOPIA clock.

The UTOPIA specifications state that the ATM layer supplies the transmit and receive UTOPIA interface clocks to the PHY layers. The T8207 may be configured to drive these clocks or to be driven by them.

In the T8207, the clocks for transmit and receive UTOPIA interfaces may be independently derived from several sources. In addition, each of these clocks may be independently configured. The TX UTOPIA clock configuration (address 010Ch) and RX UTOPIA clock configuration (address 010Eh) registers are used to select and configure the transmit UTOPIA interface and the receive UTOPIA interface clocks, respectively. See these register descriptions for more information.

54 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface

10.1 General Architecture

The high bandwidth, 32-bit cell bus is used to interconnect T8207 devices. Up to 32 devices may be connected to the bus, and cell exchange may occur between any of these devices. Each cell bus frame is 16 clock cycles, and during these 16 cycles, one cell is transmitted. The T8207 is designed to operate with a maximum cell bus frequency of 66 MHz, which translates to a cell bandwidth of 1.7 Gbits/s. The maximum achievable frequency for a given bus implementation is dependent on loading and other design considerations.

In addition to the 32 bits of data, the cell bus uses four additional control signals. The four signals include a read clock, a write clock, a frame synchronization signal, and an acknowledge signal.

The read and write clocks (cb_rc* and cb_wc* pins, respectively) establish the timing for reading and writing cells on the bus and are generated from an external clock source. The read clock is used to read the cell from the cell bus, and the write clock is used to write the cell to the cell bus. Because all devices on the cell bus read and write on the same clock edge, the write clock is delayed slightly, relative to the read clock, to ensure sufficient data hold time.

The active-low frame sync (cb_fs*) is generated by the bus arbiter and indicates the first cycle of the cell bus frame in 16 user mode or the first cycle of two cell bus frames for 32 user mode. This signal is generated every 16 clock cycles for 16 user mode or every 32 clock cycles for 32 user mode.

The acknowledge (cb_ack*) signal is used to acknowledge the successful receipt of a cell. This signal is asserted low during the next request cycle by the T8207 that receives the cell. This signal is not asserted for multicast or broadcast cells. In the event of an overflow in the control cell RX FIFO, the loopback FIFO, the TX PHY FIFO, or the cell bus input FIFO, the acknowledge signal will assert low. In the case of an overflow, this signal will not assert low for multicast and broadcast cells.

When cb_disable* is asserted, the device can receive data on the cb_d*[31:0] but cannot transmit data. The device cannot assert the cb_ack* even when a valid cell is received from the cell bus, if cb_disable* is asserted.

Several T8207 devices may reside on the cell bus, but one device must be configured as bus arbiter by clearing the cb_arb_sel bit in the cell bus configuration/status register (address 0130h) or by pulling the arb_en* lead low. The cell bus arbiter receives requests for access to the bus from all resident devices during the first cycle of the cell bus frame and grants one of these requests during the last cycle of the cell bus frame. Before issuing the grant and while a cell is transmitted on the cell bus, the arbiter executes its arbitration algorithm to determine the next device to transmit on the bus. The arbiter also generates the frame synchronization signal. Software shall designate only one device as cell bus arbiter, at any given time, to ensure proper operation of the bus.

A 5-bit unit address is assigned to each device (up to 32) on the bus. Each device uses this address to request cell transmission and to identify incoming cells destined for them. Each device is given a unique unit address by individually tying each address (ua*[4:0]) input high or low. The unit address inputs are active-low; therefore, a device

with its ua*[4:0] inputs tied to “10000” has address 15. The device makes a cell transmission request by driving the two assigned bits during the request cycle, which is the first cycle of a frame. For example, device 15 uses bits 30 and 31 of the request cycle as its request bits. (See Section 10.2, Cell Bus Frames.) Also, each device uses its unit address to determine if a received cell is destined for it. (See Section 10.3, Cell Bus Routing Headers.)

Agere Systems Inc. 55

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

The cell bus may be configured for 16-user or 32-user mode using the cb_usr_mode bit in the cell bus configuration/status register (address 0130h). In 16-user mode, all 16 devices assert their transmission requests during the first cycle of each frame, and the transmission grant for the next frame is given during the last cycle of the frame. In 32-user mode, the frame synchronization signal is asserted every two cell bus frames. The two frames are termed the odd and even frames. The frame synchronization signal marks the beginning of the even frame, and the odd frame starts 16 clock cycles later. During the request cycle of the even frame, devices zero through 15 assert their transmission requests, and during the request cycle of the odd frame, devices 16 through 31 assert theirs. Requests received from odd and even frames are serviced as a group, and grants are given in the order that the requests are received with the highest priority serviced first with the same priority requests serviced using a roundrobin algorithm. Transmission grants for the next frame are always given at the end of the current frame.

Cells to be transmitted onto the cell bus come from three sources internal to the T8207. Data cells from the UTOPIA bus are placed in the RX PHY FIFO to await transmission onto the cell bus. Control cells from the microprocessor wait in the control cell TX FIFO, and loopback cells from the cell bus wait in the loopback FIFO. Cells from these three FIFOs are priority multiplexed onto the cell bus output FIFO to be transmitted onto the cell bus.

Optional high priority can be established for data cells or control cells sent to the cell bus. If bit 9 in register 0130h

is cleared to ‘0’ then cells from the RX PHY FIFO have the highest priority , cells from the control cell TX FIFO have next highest, and finally, cells from the loopback FIFO have the lowest. If bit 9 in register 0130h is set to ‘1,’ then cells from the control cell TX FIFO have the highest priority, cells from the RX PHY FIFO have the next highest priority, and finally, cells from the loopback FIFO have the lowest priority. This bit on default is ‘0.’

Incoming cells may be broadcast, multicast, or single address types. The T8207 receiving device accepts single

address cells with an address field in the cell bus routing header that matches the device’s unit address. In addition, the device accepts all broadcast cells and certain multicast cells that it is configured to accept. (See Section

10.3.4, Multicast Routing (continued).) Before a cell is accepted, a check is done on the previous grant to verify whether it is a valid grant or not. The receiving device verifies the cell bus routing header cyclic redundancy check (CRC-4) value in the least significant 4 bits of the cell bus routing header. It also verifies the bit interleave parity (BIP-8) value from bits 24 to 31 of the last cell bus frame cycle. If either is corrupt, the cell is discarded. If kept, cells are routed to the loopback FIFO, control FIFO, or TX PHY FIFO, based on the information in its cell bus routing header. See Section 10.3, Cell Bus Routing Headers.

56 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.2 Cell Bus Frames

A cell bus frame is always 16 clock cycles. The cell bus frame has three sections (request, bus cell, and grant). During the request section, which is the first clock cycle of the frame, 16 devices assert their transmission requests onto the bus. During the bus cell section, which is the next 14 clock cycles, a cell is transmitted on the cell bus. This bus cell includes the cell bus routing header, the optional tandem routing header, and the 52-byte body of the cell. During the grant section, which is the last clock cycle of the frame, the grant is asserted, indicating which device may transmit its cell during the next frame. Also, during this last clock cycle, a parity vector is placed on the bus by the transmitting device so that error detection can be performed on the cell. Figure 14 illustrates the format for the cell bus frame.

Figure 14. Cell Bus Frame Format (Bit Positions for 16 User Mode)

31 16 15 0

CYCLE 0 U15 U14 U13 U12 U11 U10 U9 U8 U7 U6 U5 U4 U3 U2 U1 U0 CYCLE 1 CELL BUS ROUTING HEADER TANDEM ROUTING HEADER

CYCLE 2

GFC/

VPI[11:8]

VPI[7:0] VCI[15:0] PTICL

P CYCLE 3 PAYLOAD BYTE 0 PAYLOAD BYTE 1 PAYLOAD BYTE 2 PAY LO AD BYTE 3 CYCLE 4 PAYLOAD BYTE 4 PAYLOAD BYTE 5 PAYLOAD BYTE 6 PAY LO AD BYTE 7 CYCLE 5 PAYLOAD BYTE 8 PAYLOAD BYTE 9 PAYLOAD BYTE 10 PAYLOAD BYTE 11 CYCLE 6 PAYLOAD BYTE 12 PAYLOAD BYTE 13 PAYLOAD BYTE 14 PAYLOAD BYTE 15 CYCLE 7 PAYLOAD BYTE 16 PAYLOAD BYTE 17 PAYLOAD BYTE 18 PAYLOAD BYTE 19 CYCLE 8 PAYLOAD BYTE 20 PAYLOAD BYTE 21 PAYLOAD BYTE 22 PAYLOAD BYTE 23 CYCLE 9 PAYLOAD BYTE 24 PAYLOAD BYTE 25 PAYLOAD BYTE 26 PAYLOAD BYTE 27

CYCLE 10 PAYLOAD BYTE 28 PAYLOAD BYTE 29 PAYLOAD BYTE 30 PAYLOAD BYTE 31 CYCLE 11 PAYLOAD BYTE 32 PAYLOAD BYTE 33 PAYLOAD BYTE 34 PAYLOAD BYTE 35 CYCLE 12 PAYLOAD BYTE 36 PAYLOAD BYTE 37 PAYLOAD BYTE 38 PAYLOAD BYTE 39 CYCLE 13 PAYLOAD BYTE 40 PAYLOAD BYTE 41 PAYLOAD BYTE 42 PAYLOAD BYTE 43 CYCLE 14 PAYLOAD BYTE 44 PAYLOAD BYTE 45 PAYLOAD BYTE 46 PAYLOAD BYTE 47

CYCLE 15 BIT INTERLEAV E PARITY

—————————————————

GPG

GRANT NUMBER

Agere Systems Inc. 57

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

Figure 15. Cell Bus Frame Format (Bit Positions for 32 User Mode)

31 16 15 0

CYCLE 0 U15 U14 U13 U12 U11 U10 U9 U8 U7 U6 U5 U4 U3 U2 U1 U 0 CYCLE 1 CELL BUS ROUTING HEADER TANDEM ROUTING HEADER

CYCLE 2

GFC/

VPI[11:8]

VPI[7:0] VCI[15:0] PTICL

P CYCLE 3 PAYLOAD BYTE 0 PAYLOAD BYTE 1 PAYLOAD BYTE 2 PAYLOAD BYTE 3 CYCLE 4 PAYLOAD BYTE 4 PAYLOAD BYTE 5 PAYLOAD BYTE 6 PAYLOAD BYTE 7 CYCLE 5 PAYLOAD BYTE 8 PAYLOAD BYTE 9 PAYLOAD BYTE 10 PAYLOAD BYTE 11 CYCLE 6 PAYLOAD BYTE 12 PAYLOAD BYTE 13 PAYLOAD BYTE 14 PAYLOAD BYTE 15 CYCLE 7 PAYLOAD BYTE 16 PAYLOAD BYTE 17 PAYLOAD BYTE 18 PAYLOAD BYTE 19 CYCLE 8 PAYLOAD BYTE 20 PAYLOAD BYTE 21 PAYLOAD BYTE 22 PAYLOAD BYTE 23 CYCLE 9 PAYLOAD BYTE 24 PAYLOAD BYTE 25 PAYLOAD BYTE 26 PAYLOAD BYTE 27

CYCLE 10 PAYLOAD BYTE 28 PAYLOAD BYTE 29 PAYLOAD BYTE 30 PAYLOAD BYTE 31

CYCLE 11 PAYLOAD BYTE 32 PAYLOAD BYTE 33 PAYLOAD BYTE 34 PAYLOAD BYTE 35 CYCLE 12 PAYLOAD BYTE 36 PAYLOAD BYTE 37 PAYLOAD BYTE 38 PAYLOAD BYTE 39 CYCLE 13 PAYLOAD BYTE 40 PAYLOAD BYTE 41 PAYLOAD BYTE 42 PAYLOAD BYTE 43 CYCLE 14 PAYLOAD BYTE 44 PAYLOAD BYTE 45 PAYLOAD BYTE 46 PAYLOAD BYTE 47

CYCLE 15 BIT INTERLEAVE PARITY

—————————————————

GPG

GRANT NUMBER

CYCLE 16 U31 U30 U29 U28 U27 U26 U25 U24 U23 U22 U21 U20 U19 U18 U17 U16 CYCLE 17 CELL BUS ROUTING HEADER TANDEM ROUTING HEADER

CYCLE 18

GFC/

VPI[11:8]

VPI[7:0] VCI[15:0] PTICL

P CYCLE 19 PAYLOAD BYTE 0 PAYLOAD BYTE 1 PAYLOAD BYTE 2 PAYLOAD BYTE 3 CYCLE 20 PAYLOAD BYTE 4 PAYLOAD BYTE 5 PAYLOAD BYTE 6 PAYLOAD BYTE 7 CYCLE 21 PAYLOAD BYTE 8 PAYLOAD BYTE 9 PAYLOAD BYTE 10 PAYLOAD BYTE 11 CYCLE 22 PAYLOAD BYTE 12 PAYLOAD BYTE 13 PAYLOAD BYTE 14 PAYLOAD BYTE 15 CYCLE 23 PAYLOAD BYTE 16 PAYLOAD BYTE 17 PAYLOAD BYTE 18 PAYLOAD BYTE 19 CYCLE 24 PAYLOAD BYTE 20 PAYLOAD BYTE 21 PAYLOAD BYTE 22 PAYLOAD BYTE 23 CYCLE 25 PAYLOAD BYTE 24 PAYLOAD BYTE 25 PAYLOAD BYTE 26 PAYLOAD BYTE 27 CYCLE 26 PAYLOAD BYTE 28 PAYLOAD BYTE 29 PAYLOAD BYTE 30 PAYLOAD BYTE 31 CYCLE 27 PAYLOAD BYTE 32 PAYLOAD BYTE 33 PAYLOAD BYTE 34 PAYLOAD BYTE 35 CYCLE 28 PAYLOAD BYTE 36 PAYLOAD BYTE 37 PAYLOAD BYTE 38 PAYLOAD BYTE 39 CYCLE 29 PAYLOAD BYTE 40 PAYLOAD BYTE 41 PAYLOAD BYTE 42 PAYLOAD BYTE 43 CYCLE 30 PAYLOAD BYTE 44 PAYLOAD BYTE 45 PAYLOAD BYTE 46 PAYLOAD BYTE 47

CYCLE 31 BIT INTERLEAVE PARITY

—————————————————

GPG

GRANT NUMBER

58 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

Devices on the cell bus make their requests during the first cycle of each frame. In 16-user mode, each device asserts a request every frame. In 32-user mode, each device asserts a request every two frames. In 32-user mode, devices with unit addresses 0 through 15 assert their requests during the even frames, and devices with unit addresses 16 through 31 assert their requests during the odd frames. During cycle 0 of their assigned frame, each device drives two of the 32 data bits available. The position of the two request bits for each device is based

on the device’s unit address. The assigned bit positions for each device are illustrated in Figure 14 and Figure 15 for 16-user and 32-user modes, respectively. For example, in the figures, the device with unit address 0 makes its requests using the 2 bits labeled as U0. Two bits, instead of one, are used for each device so the priority of the request may be included. The priority of the request is set up using the cb_req_pr bits in the main configuration/control register (address 0110h). See Table 58 in Section 14.3, Extended Memory Registers, for more information.

During clock cycles 1 through 14, the device that was granted the bus at the end of the previous frame sends its bus cell. The bus cell sent includes the cell bus routing header, the tandem routing header, and the original UTOPIA cell with the header error check (HEC) byte removed. The HEC byte is removed because the cell bus does its own error check over the complete cell using the bit interleave parity byte. The HEC byte is recreated and inserted before the received cell is placed on the UTOPIA bus.

The cell bus routing header indicates the type of the cell (data, control, loopback) and its destination (single, multicast, broadcast). See Section 10.3, Cell Bus Routing Headers, for more information on the cell bus routing header structure. The optional tandem routing header is configured by the user.

The 32 bits of the grant section of the frame (clock cycle 15) includes the bit interleave parity (BIP-8) byte, the grant parity bit, the grant enable bit, and the grant number. The most significant 8 bits of the grant section of the frame is the BIP-8 byte. The BIP-8 byte is calculated over 54 bytes starting with the first tandem routing header byte and ending with the last payload byte. To calculate this bit interleave parity, an exclusive-OR operation is performed on

the first byte of the tandem routing header and the value “11111111.” The exclusive-OR operation then is performed on this result and the following byte. The operation is then repeated with every successive byte through the last data byte of the payload. The resulting byte becomes the BIP-8 byte of the grant section. The next 17 bits of the grant section are unused. The least significant 7 bits of the grant section are used to grant transmission requests. The grant number is located in the least significant 5 bits of the grant section and is the unit address of the device that transmits a cell during the next frame. The grant enable, bit 5, is an active-high signal that indicates if the grant is valid. Finally, the grant parity, bit 6, is the odd parity check calculated over the other six grant bits.

Agere Systems Inc. 59

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.3 Cell Bus Routing Headers

The cell bus routing header gives information about the cell and its routing. There are seven different formats for cell bus routing headers. See Figure 16. These headers cover broadcast, multicast, and single address routing. A T8207 device on the cell bus accepts all broadcast cells and certain multicast cells that it is configured to accept. Broadcast or multicast routed cells may be data cells or control cells. The T8207 receiving device accepts single

address cells with an address field in its cell bus routing header that matches the device’s unit address. Cells, routed as single address, may be data, control, or loopback cells.

Figure 16. Cell Bus Routing Headers

The H field (b0 to b3) is the cell bus routing header cyclic redundancy check (CRC-4) calculated over the other 12 bits (b4 to b15) of the header. It is provided for cell bus routing header error detection. When cells arrive from the cell bus, the receiving device calculates the CRC-4 over the most significant 12 bits of the cell bus routing header and compares its calculation to the CRC-4 value stored in the H field of the cell bus routing header. If the two do not match, the cell is discarded.

10.3.1 Control Cells

The microprocessor connected to the T8207 may send control cells to the cell bus by writing the cell to the control cell transmit direct memory at addresses A0h to D7h (or extended memory at addresses 0900h to 0936h). After the cell is written to memory, the microprocessor sets the cntl_cell_wr bit in the main configuration/control register (address 0110h). This bit returns to zero when the cell is transmitted and memory is available to load a new control cell into the device.

Control cells accepted from the cell bus are routed to the control cell RX FIFO. The microprocessor connected to the T8207 reads the control cell at the head of the FIFO using the control cell receive direct memory at addresses 60h to 93h (or extended memory at addresses 0800h to 0832h). After the microprocessor reads the cell, it sets the cntl_cell_rd bit in the main configuration/control register (address 0110h) to remove the cell from the head of the FIFO.

MULTICAST CONTROL CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

11— — MULTICAST NET NUMBER H

MULTICAST DATA CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

1 0 — — MULTICAST NET NUMB ER H

SINGLE DESTINATION DATA CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

0 0 — — — — 0 UNIT ADDRESS H

SINGLE DESTINATION CONTROL CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

0 1 — — — — 0 UNIT ADDRESS H

SINGLE DESTINATION LOOPBACK CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

0 0 0 — — — 1 UNIT ADDRESS H

BROADCAST DATA CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

0 0 1 ——— 1————— H

BROADCAST CONTROL CELL HEADER

b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0

0 1 1 ——— 1————— H

60 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.3.2 Data Cells

Data cells accepted from the cell bus are routed to the TX PHY FIFO. From the TX PHY FIFO, the cell is routed to

the appropriate transmit queue using the information about the cell’s priority and the queue group to which it is destined. The priority of the cell is indicated by 2 bits obtained from the first 64 bits of the bus cell (cell bus routing header, tandem routing header, and ATM cell header). The position of these 2 bits in the cell are user programmable during configuration using the prior0_sel[5:0] and prior1_sel[5:0] bits of the routing information 3 register (address 0204h). The queue group to which the cell is destined is indicated by 4 bits obtained from the first 64 bits of the bus cell (cell bus routing header, tandem routing header, and ATM cell header). The position of these 4 bits in these headers are user programmable using the mphy1_sel[5:0] and mphy2_sel[5:0] bits of the routing information 1 register (address 0200h) and the mphy3_sel[5:0] and mphy0_sel[5:0] bits of the routing information 2 register (address 0202h). See Tables 90, 91, and 92 in Section 14.3, Extended Memory Registers. None of the priority or MPHY bits are required to be adjacent. For more information on queue groups, see Section 11.4, Queuing.

If the T8207_sel bit (Table 59) is zero, the mphy3_sel[5:0] bits are not used.

10.3.3 Loopback Cells

A loopback cell may be sent to the cell bus for diagnostic purposes. Initially, the loopback cell is sent from one T8207 (device 1) to a second T8207 (device 2). The second T8207 (device 2) returns the cell to the first T8207 (device 1), or, if desired, the second T8207 (device 2) may send the cell on to one or more entirely different T8207 devices. Device 2 accepts the loopback cell and replaces the most significant 12 bits of the cell bus routing header with the routing_header bits in its loopback register (address 0118h). The 12 routing_header bits in the loopback register correspond to the upper 12 bits of a single destination control cell header, a multicast control cell header, or a broadcast control cell header. (See Figure 16.)

To create a loopback path from device 1 to device 2, and back to device 1, coordinated control of device 1 and device 2 is needed. First, the microprocessor connected to device 2 sets up the loopback by writing the routing_header bits in the loopback register of device 2. The routing_header bits indicate a single destination control cell with a unit address field for device 1. Second, the microprocessor connected to device 1 writes a loopback cell to the control cell transmit direct memory (addresses A0h to D7h) of device 1. (See Section 10.3.1, Control Cells of this document.) The cell bus routing header of this cell is the single destination loopback type, and the unit address section of the header contains the address of device 2. To send the loopback cell, a ‘1’ is then written to

the cntl_cell_wr bit of the main configuration/control register (address 0110h).

Care must be taken to ensure that the routing_header bits in a T8207 device are not changed until any previously setup loopback cell has been received and retransmitted. If these bits are changed prematurely, misrouting will occur.

10.3.4 Multicast Routing

The T8207 may be programmed to accept certain multicast data cells using the multicast memories at addresses E0h through FFh (or 0C00h through 0C1Eh) and 0C20h through 0DFEh. The net numbers of accepted multicast control cells are programmed in the memory space E0h through FFh (or 0C00h through 0C1Eh) and 0C20h through 0DFEh. These memory spaces hold 256 bits each. Each bit represents a multicast net number from 0 to

255.

If the T8207_sel bit (Table 59) is cleared, the multicast memories at addresses 0D00h to 0DFEh are ignored. Note: To prevent potential multicast memory errors, these memory spaces should be cleared during the initializa-

tion process.

For A TM mode, if the T8207_sel bit is cleared, the net numbers of accepted multicast data cells are programmed in the multicast number memories, which are divided among eight PHY ports. If 16 ports are used in this mode, each memory space is shared between two ports, e.g., ports zero and one use the memory assigned to PHY 0, ports two and three use the memory assigned to PHY 1, and so on (see Section 9.2.2, Outgoing ATM Mode (Cells Sent by T8207)).

Agere Systems Inc. 61

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.3.4 Multicast Routing (continued)

For ATM mode, if the T8207_sel bit is set, the net numbers of accepted multicast data cells are programmed in the multicast number memories, which are divided among sixteen PHY ports. If 16 ports are used, each port has one memory space. If 32 ports are used, each memory space is shared between two ports, e.g., ports zero and one use the memory assigned to PHY 0, ports two and three use the memory assigned to PHY 1, and so on.

The cell priority bits select the specific queue in the queue group to which the cell is routed. (See Section 11.4, Queuing.) Note that multicast control cells use the same multicast number memory as PHY 0 multicast data cells. See Table 122 in Section 14.3, Extended Memory Registers and Table 52 in Section 14.2, Direct Memory Access Registers, respectively.

For PHY mode, multicast cells are only transmitted to queue group 0, and only the PHY port 0 and control cell multicast direct memory at addresses E0h through FFh (or 0C00h through 0C1Eh) is used. The cell priority determines the specific queue in queue group 0 to which the cell is routed. (See Section 10.3.2, Data Cells.)

10.3.5 Broadcast Routing

Broadcast control cells are transmitted and received as described in Section 10.3.1, Control Cells. The broadcast control cell bus routing header has a broadcast control cell header type.

For ATM mode, if the T8207_sel bit (Table 59) is cleared and 8 PHY ports or less are being used, the broadcast data cells are transmitted to all the ports. If 16 ports are used, the broadcast data cells are transmitted to only 8 of the 16 ports depending on the cell priority bits that select the specific queue.

For ATM mode, if the T8207_sel bit (T able 59) is set, and 16 PHY ports or less are being used, the broadcast data cells are transmitted to all the ports. If 32 ports are used, the broadcast data cells are transmitted to only 16 of the 32 ports depending on the cell priority bits that select the specific queue.

For PHY mode, if SDRAM is bypassed, broadcast data cells are only transmitted to queue 0. If the SDRAM is

not bypassed, broadcast data cells are only transmitted to queue group 0, and only PHY port 0 is used (although the device will take the time to try to broadcast data cells to all the ports, cells will not be stored in queue groups other than 0).

10.4 Cell Bus Arbitration

One of the T8207 devices sharing the cell bus must be configured as bus arbiter by clearing the cb_arb_sel bit in the cell bus configuration/status register (address 0130h) or by pulling the arb_en* lead low. Using an arbitration algorithm, the arbiter decides the next device to transmit on the cell bus and issues the grant signals at the end of the cell bus frame. The arbiter also generates the active-low frame synchronization signal that occurs every 16 clock cycles in 16-user mode and every 32 clock cycles in 32-user mode.

To grant transmission requests, the arbiter must analyze requests received during the request section of the current frame for 16-user mode or during two request cycles for 32-user mode. The arbitration algorithm used is round-robin and based on the priority of the request and the last request granted.

The arbiter circuitry in all T8207 devices on the cell bus will synchronize to the active arbiter on the cell bus. So, when an inactive device becomes the arbiter, it will begin sending frame synchronization signals that coincide to the clock cycle that the original arbiter would have sent its next frame synchronization signal. This prevents the new arbiter from misinterpreting random signals on its first request cycle as valid requests.

62 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.5 Cell Bus Monitoring

Every T8207 device monitors the cell bus for proper operation. The monitoring section of the T8207 checks for the presence of the read clock, the write clock, and the frame synchronization signal. The cb_wc_miss bit in the main interrupt status 1 register (address 0102h) is set when the write clock is inactive for 32 mclk cycles. Likewise, the cb_rc_miss bit in the main interrupt status 1 register is set when the read clock is inactive for 32 mclk cycles. In addition, the cb_fs_miss bit in the main interrupt status 1 register is set when the frame synchronization signal is inactive for greater than 16 cell bus read clock cycles for 16-user mode or for greater than 32 read clock cycles for 32-user mode. This bit is also set when the cell bus write clock is inactive for 32 mclk cycles.

When cells arrive from the cell bus, the cell bus monitoring section of the receiving device calculates the bit interleave parity value over the 54-byte field from the first tandem routing header byte through the final payload byte. If this calculated value does not match the value in bits 24 through 31 of the final clock cycle of the frame, the cell is discarded.

The T8207 detects when a device asserts transmission requests and is not granted permission within a programmable time period. The cb_grnt_to bit in the main interrupt status 1 register (address 0102h) is set when a device has not been granted permission to transmit within the number of frames programmed in the cb_req_to bits of the main configuration 3 register (address 0116h).

10.6 GTL+ Logic

For the T8207, the cell bus data, frame sync, and acknowledge signals use onboard GTL+ transceivers, and the cell bus clock signals use onboard GTL+ receivers. The GTL+ bus drivers are open drain and require terminating resistors at both ends of each line. The terminating resistor (R) may be from 40 Ω to 50 Ω and should be pulled up to 1.5 V ±

10% (VTT). The actual value of the terminating resistors should be chosen to match the bus line imped-

ance. Figure 17A below illustrates the terminating resistors and the configuration of one GTL+ bus line. The termination resistors are typically placed at the ends of the bus of the backplane.

The signal rise and fall times from the transceivers are carefully controlled to minimize out of band signals without affecting the overall transmission rates. These controlled signal edges, in addition to proper resistive line termination, minimize noise and ringing. The slew rate of the GTL+ buffers can be programmed using bits [2:0] of register 2Eh.

The GTL+ receiver compares its input signal to a voltage reference, cb_vref, to determine the logic level of the input. The value of the voltage reference is 2/3 V

TT and is created using the voltage divider shown in Figure 17B.

The 1 kΩ resistors are 1% because the cb_vref voltage must track V

TT by 1%. The 0.01 µF capacitor is a decou-

pling capacitor on the cb_vref input.

Figure 17. GTL+ External Circuitry

5-8011a (F)

5-8012a(F)

A. GTL+ Bus with Terminating Resistors B. GTL+ Threshold Voltage Reference

TT VTT

CelXpres

T8207

CelXpres

T8207

CelXpres

T8207

1 k

Ω ± 1%

1 k

Ω ± 1%

1 k

Ω ± 1%

cb_vref

0.01 µF

cb_vref_vss

Agere Systems Inc. 63

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

10 Cell Bus Interface (continued)

10.7 Cell Bus Write and Read Clocks

The read and write clocks (cb_wc* and cb_rc* pins) are supplied from an external source. The write clock should be delayed 1.5 ns to 4 ns relative to the read clock to ensure sufficient data hold time. The position of the clock source relative to the cell bus devices on the card or on connecting cards determines the actual delay that should be used. When the clock source is centrally located among the cell bus devices, a longer delay may be used. When the clock source is at either end of the cell bus devices, a shorter delay is needed. Also, a higher clock frequency requires a shorter delay.

64 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface

For outgoing UTOPIA cells, the TX UTOPIA cell buffer supports 64 queues. These queues are separated into 16 queue groups, each consisting of four different priority queues as described in Section 9.2.2, Outgoing ATM Mode (Cells Sent by T8207). This cell buffer holds 128 outgoing cells. Additional buffering is provided by an external SDRAM. Connection to an external SDRAM is selected by clearing the sdram_bypass bit in the main configuration 1 register (address 0100h).

If the SDRAM is not used, it is bypassed by setting the sdram_bypass bit in the main configuration 1 register at start-up. When bypassed, only queue 0 of the 64 queues in the TX UTOPIA cell buffer is used. The only buffering available in this mode is the 128-cell internal memory (TX PHY FIFO) and up to 128 cells from queue 0 of the TX UTOPIA cell buffer. The TX PHY FIFO overflows only if the TX UTOPIA cell buffer is full, and as a result, the TX PHY FIFO is also full. The setting of the div_queue bits in the main configuration 2 register (address 0112h) determines the number of cell locations allocated to queue 0 of the TX UTOPIA cell buffer. Be sure to program these bits

to “101” to maximize buffering.

11.1 Memory Configuration

The SDRAM interface supports from 2 Mbytes to 32 Mbytes of memory. This memory size is realized using 16 Mbit or 64 Mbit devices. Table 17 below outlines the various memory configurations supported.

Table 17. Supported Memory Configurations

11.2 Powerup Sequence

The powerup sequence for the SDRAM must be performed manually before the SDRAM is enabled. Using the idle state 1 and 2 registers (addresses 0420h and 0422h), the manual access state 1 and 2 registers (addresses 0424h and 0426h), and the gen_man_acc bit in the SDRAM control register (address 0400h), follow the powerup command sequence prescribed by the SDRAM manufacturer. The T8207 does not control the chip select, the clock enable, and the DQM inputs to the SDRAM. These signals should be externally tied to the appropriate logic level or external control signal.

To manually execute SDRAM commands, first set up the idle values for CAS*, RAS*, WE*, bank select (BS), and the address signals using the cas_idle, ras_idle, we_idle, bs_idle[1:0], and addr_idle[11:0] bits in the idle state 1 and 2 registers. Then manually set up the value of these signals for the first SDRAM command using the cas_man, ras_man, we_man, bs_man[1:0], and addr_man[11:0] bits in the manual access state 1 and 2 registers. Finally, write a ‘1’ to the gen_man_acc bit in the SDRAM control register. Writing this ‘1’ drives the CAS, RAS, WE*, BS, and address values (in the manual access state 1 and 2 registers) onto the associated pins, for one SDRAM clock cycle. After the one clock cycle, these signals return to their idle state. Repeat this process, making sure minimum timing between commands is met, until the powerup process has been completed.

In the powerup sequence, configure the mode register of the SDRAM for a burst length of one and a CAS latency of two or three. With a burst length of one, sequential and interleave addressing behave the same, so the SDRAM may be configured for either addressing mode.

Number of

Devices

Device Memo ry Size and D ata

Bus Organization

Number of

Columns

Number of

Banks

Number of

Rows

Total

Memory

1 16 Mbit, 16-bit data bus 256 2 2048 2 Mbyte 2 16 Mbit, 8-bit data bus 512 2 2048 4 Mbyte 4 16 Mbit, 4-bit data bus 1024 2 2048 8 Mbyte 1 64 Mbit, 16-bit data bus 256 4 4096 8 Mbyte 2 64 Mbit, 8-bit data bus 512 4 4096 16 Mbyte 4 64 Mbit, 4-bit data bus 1024 4 4096 32 Mbyte

Agere Systems Inc. 65

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (continued)

11.3 SDRAM Interface Timing

The mclk clock is the source of the SDRAM clock (sd_clk) from the T8207. Based on the frequency of the SDRAM clock and the speed grade of the SDRAM, four timing parameters must be programmed into the SDRAM configuration register at address 0408h. These timing parameters are specified in SDRAM (mclk) clock cycles and are listed below:

■ RAS inactive to CAS active (ras2cas)—its value may be set from two to four SDRAM clock cycles.

■ CAS inactive to precharge command active (cas2pre)—its value may be set from one to four SDRAM clock

cycles.

■ Precharge command inactive to next command active (pre2cmd)—its value may be set from one to four SDRAM

clock cycles.

■ CAS before RAS (CBR) refresh command inactive to next CBR refresh command active (ref2cmd)—its value

may be set to 3, 7, or 15 SDRAM clock cycles.

Actual values for these parameters are obtained from the data sheet of the SDRAM used. For optimum performance, these parameters should be programmed to the lowest acceptable values. The earliest time that a CAS may be asserted after an RAS may be obtained from the data sheet parameter that describes the minimum time from the activate command to the read/write command. Three parameters affect the earliest time that a precharge command may follow a CAS. For read commands, a precharge command may be issued one clock earlier than the last read data. The actual number of clock cycles depends on the CAS latency needed for the device. For write commands, the earliest time that a precharge command may be issued following a CAS may be obtained from the SDRAM data sheet parameter that describes the minimum time from the last data in to the precharge command. In addition to these two parameters, the minimum time from the activate command to the precharge command may need to be considered to obtain the value for cas2pre. If the SDRAM is only accessed for queuing purposes, 28 consecutive CAS commands will be executed between the activate command and the precharge command, and the minimum time from the activate command to the precharge command does not need to be considered. If the microprocessor reads and writes the SDRAM memory, only one CAS command will be executed between the activate command and the precharge command. In this case, the minimum time from the activate command to the precharge command is significant and must be considered. The minimum time from the precharge command to the next command may be obtained from the data sheet parameter that describes the minimum time from the precharge command to the activate command. The minimum time from the CBR refresh command to the next CBR refresh command may be obtained from the data sheet. In the T8207, the minimum time from CBR refresh to any other command is 15 SDRAM clock cycles. In the data sheet, the parameters may be specified in actual time units rather than clock cycles. To determine the number of clock cycles, divide the parameter value by the SDRAM clock period. Figure 18 below illustrates these timing parameters and the number of clock cycles needed to read or write a cell using the default values for the parameters.

5-7785bF

Figure 18. SDRAM Timing Parameters

RAS

(1)

CBR

REFRESH

{2, 3, 4}

ras2cas

CAS

(1 TO 28)

{1, 2, 3, 4}

cas2pre

PRECHARGE

(1)

{3, 7, 15}

ref2cmd

{1, 2, 3, 4}

pre2cmd

COMMAND

SINGLE COMMAND

THE BOXES REPRESENT THE NUMBER

OF IDLE CYCLES BETWEEN STATES. DEFAULT

VALUES ARE IN BOLD FOR ras2cas, cas2pre, pre2cmd, AND ref2cmd.

(1)

66 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (contin ued)

11.4 Queuing

Queuing is different for a T8207 device with its T8207_sel (T able 59) bit set than a T8207 device with its T8207_sel bit cleared.

For a device configured in ATM mode with its T8207_sel bit set, up to 16 groups of queues with four priorities per group may be configured in the SDRAM for a total of 64 queues. Therefore, the four port group address bits point to one of 16 queue groups, and the two priority bits point to one of four queues in the group. (For a description of the port group address and priority bits, see Section 10.3.2, Data Cells.) Priority bits with a value of zero represent the highest priority, and those with a value of three, the lowest priority.

If the ATM is configured to support eight or less PHY ports, each port is mapped to one queue group using the port_rte[31:0] bits in the TX PHY FIFO routing 0 and 1 registers (addresses 017Ch and 017Eh). For example, for a configuration of eight PHY ports, which includes ports 0, 2, 4, 6, 8, 10, 12, and 14, PHY port 0 is assigned queue group zero or queues zero, one, two, and three. Likewise, PHY port 2 is assigned group one or queues four, five, six, and seven, and so on.

An ATM configured to support 16 PHY ports is a special case. When the T8207_sel bit is set and the ATM is configured to support 16 PHY ports, each port (0—15) is assigned to its associated queue group as illustrated in T able 18, regardless of the value of the port_rte[63:0] bits. In this case, port 0 is assigned to queue group 0, port 1 to queue group 1, and so on.

For an ATM configured to support 32 PHY ports, each queue group is shared between two ports as specified in Section 9.2.2, Outgoing ATM Mode (Cells Sent by T8207), and the four queues may be split in any way between the two ports using the port_rte[63:0] bits. Table 19 illustrates the relationship between the queue organization and the port group address/priority bits for a device configured to support 32 PHY ports and whose port_rte[63:0] bits are programmed to the normal 32-port mode as described in Section 9.2.2, Outgoing ATM Mode (Cells Sent by T8207). See the TX PHY FIFO routing 3, 2, 0, and 1 registers at addresses 0178h, 017Ah, 017Ch, and 017Eh.

When the T8207_sel bit is cleared, 32 PHY ports are not supported. In this mode, eight or less PHY ports are each mapped to one queue group using the port_rte[31:0] bits in the TX PHY FIFO routing 0 and 1 registers. For 16 PHY ports, each queue group is shared between two ports, and the four queues may be split in any way between the two ports using the port_rte[31:0] bits. Table 20 illustrates the relationship between the queue organization and the port address/priority bits for a device configured to support 16 PHY ports and whose port_rte[31:0] bits are programmed to the normal 16-port mode as described in Section 9.2.2, Outgoing ATM Mode (Cells Sent by T8207). See the TX PHY FIFO routing 0 and 1 registers at addresses 017Ch and 017Eh.

Agere Systems Inc. 67

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (continued)

Table 18. Queue Organization and Port Group Address/Priority Bits for 16 Ports with T8207_sel = 1

Port Number Queue Group Queue Number Priority Port Group Address Bits Priority Bits

0 0 0 Highest “0000” “00” 0 0 1 High “0000” “01” 0 0 2 Low “0000” “10” 0 0 3 Lowest “0000” “11” 1 1 4 Highest “0001” “00” 1 1 5 High “0001” “01” 1 1 6 Low “0001” “10” 1 1 7 Lowest “0001” “11” 2 2 8 Highest “0010” “00” 2 2 9 High “0010” “01” 2 2 10 Low “0010” “10” 2 2 11 Lowest “0010” “11” 3 3 12 Highest “0011” “00” 3 3 13 High “0011” “01” 3 3 14 Low “0011” “10” 3 3 15 Lowest “0011” “11” 4 4 16 Highest “0100” “00” 4 4 17 High “0100” “01” 4 4 18 Low “0100” “10” 4 4 19 Lowest “0100” “11” 5 5 20 Highest “0101” “00” 5 5 21 High “0101” “01” 5 5 22 Low “0101” “10” 5 5 23 Lowest “0101” “11” 6 6 24 Highest “0110” “00” 6 6 25 High “0110” “01” 6 6 26 Low “0110” “10” 6 6 27 Lowest “0110” “11” 7 7 28 Highest “0111” “00” 7 7 29 High “0111” “01” 7 7 30 Low “0111” “10” 7 7 31 Lowest “0111” “11” 8 8 32 Highest “1000” “00” 8 8 33 High “1000” “01” 8 8 34 Low “1000” “10” 8 8 35 Lowest “1000” “11” 9 9 36 Highest “1001” “00” 9 9 37 High “1001” “01” 9 9 38 Low “1001” “10” 9 9 39 Lowest “1001” “11”

68 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (contin ued)

Table 18. Queue Organization and Port Group Address/Priority Bits for 16 Ports with T8207_sel = 1

(continued)

Port Number Queue Group Queue Number Priority Port Group Address Bits Priority Bits

10 10 40 Highest “1010” “00” 10 10 41 High “1010” “01” 10 10 42 Low “1010” “10” 10 10 43 Lowest “1010” “11” 1 1 11 44 Highest “1011” “00” 11 11 45 High “1011” “01” 1 1 11 46 Low “1011” “10” 1 1 11 47 Lowest “1011” “11” 12 12 48 Highest “1100” “00” 12 12 49 High “1100” “01” 12 12 50 Low “1100” “10” 12 12 51 Lowest “1100” “11” 13 13 52 Highest “1101” “00” 13 13 53 High “1101” “01” 13 13 54 Low “1101” “10” 13 13 55 Lowest “1101” “11” 14 14 56 Highest “1110” “00” 14 14 57 High “1110” “01” 14 14 58 Low “1110” “10” 14 14 59 Lowest “1110” “11” 15 15 60 Highest “1111” “00” 15 15 61 High “1111” “01” 15 15 62 Low “1111” “10” 15 15 63 Lowest “1111” “11”

Agere Systems Inc. 69

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (continued)

Table 19. Queue Organization and Port Group Address/Priority Bits for 32 Ports

Port Number Queue Group Queue Number Priority Port Group Address Bits Priority Bits

000High

“0000” “00”

002Low

“0000” “10”

101High

“0000” “01”

103Low

“0000” “11”

214High

“0001” “00”

216Low

“0001” “10”

315High

“0001” “01”

317Low

“0001” “11”

428High

“0010” “00”

4210Low

“0010” “10”

529High

“0010” “01”

5211Low

“0010” “11”

6 3 12 High

“0011” “00”

6314Low

“0011” “10”

7 3 13 High

“0011” “01”

7315Low

“0011” “11”

8 4 16 High

“0100” “00”

8418Low

“0100” “10”

9 4 17 High

“0100” “01”

9419Low

“0100” “11”

10 5 20 High

“0101” “00”

10 5 22 Low

“0101” “10”

11521High

“0101” “01”

11523Low

“0101” “11”

12 6 24 High

“0110” “00”

12 6 26 Low

“0110” “10”

13 6 25 High

“0110” “01”

13 6 27 Low

“0110” “11”

14 7 28 High

“0111” “00”

14 7 30 Low

“0111” “10”

15 7 29 High

“0111” “01”

15 7 31 Low

“0111” “11” 16 8 32 High “1000” “00” 16 8 34 Low “1000” “10” 17 8 33 High “1000” “01” 17 8 35 Low “1000” “11” 18 9 36 High “1001” “00” 18 9 38 Low “1001” “10” 19 9 37 High “1001” “01” 19 9 39 Low “1001” “11” 20 10 40 High “1010” “00” 20 10 42 Low “1010” “10”

70 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (contin ued)

Table 19. Queue Organization and Port Group Address/Priority Bits for 32 Ports

(continued)

Port Number Queue Group Queue Number Priority Port Group Address Bits Priority Bits

21 10 41 High “1010” “01” 21 10 43 Low “1010” “11” 22 11 44 High “1011” “00” 22 11 46 Low “1011” “10” 23 11 45 High “1011” “01” 23 11 47 Low “1011” “11” 24 12 48 High “1100” “00” 24 12 50 Low “1100” “10” 25 12 49 High “1100” “01” 25 12 51 Low “1100” “11” 26 13 52 High “1101” “00” 26 13 54 Low “1101” “10” 27 13 53 High “1101” “01” 27 13 55 Low “1101” “11” 28 14 56 High “1 110” “00” 28 14 58 Low “1110” “10” 29 14 57 High “1 110” “01” 29 14 59 Low “1110” “11” 30 15 60 High “1111” “00” 30 15 62 Low “1111” “10” 31 15 61 High “1111” “01” 31 15 63 Low “1111” “11”

Agere Systems Inc. 71

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (continued)

Table 20. Queue Organization and Port Group Address/Priority Bits for 16 Ports with T8207_sel = 0

Port Number Queue Group Queue Number Priority Port Group Address Bits Priority Bits

000High

“000” “00”

002Low

“000” “10”

101High

“000” “01”

103Low

“000” “11”

214High

“001” “00”

216Low

“001” “10”

315High

“001” “01”

317Low

“001” “11”

428High

“010” “00”

4210Low

“010” “10”

529High

“010” “01”

5211Low

“010” “11”

6 3 12 High

“011” “00”

6314Low

“011” “10”

7 3 13 High

“011” “01”

7315Low

“011” “11”

8 4 16 High

“100” “00”

8418Low

“100” “10”

9 4 17 High

“100” “01”

9419Low

“100” “11”

10 5 20 High

“101” “00”

10 5 22 Low

“101” “10”

11 5 21 High

“101” “01”

11 5 23 Low

“101” “11”

12 6 24 High

“110” “00”

12 6 26 Low

“110” “10”

13 6 25 High

“110” “01”

13 6 27 Low

“110” “11”

14 7 28 High

“111” “00”

14 7 30 Low

“111” “10”

15 7 29 High

“111” “01”

15 7 31 Low

“111” “11”

72 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (contin ued)

Of the four priority queues, the highest-priority (priority zero), lowest-delay queue may be used for constant bit rate (CBR) traffic. The other three queues, in descending order of priority, may be used for variable bit rate (VBR), available bit rate (ABR), and unspecified bit rate (UBR) traffic, respectively. Generally , as the priority becomes lower, the queues become larger because lower-priority cells are likely to accumulate while higher-priority cells are transmitted.

The size and location of each queue is programmable using the base_addressX[24:6] and end_addrX[24:6] bits in the Queue X Definition Structure shown in Table 119. Using these base and end address registers, the size of each queue may be programmed to a minimum of four cells and up to a maximum of 512K cells in one-cell increments.

Each queue must be disabled during queue configuration by clearing the queueX_rd_en and queueX_wr_en bits in the queue X registers (addresses 0440h through 04BEh) (Table 118).

Cells sent to write-disabled queues will be discarded. Cells sent to read-disabled queues will be written into the SDRAM but never transmitted to the TX UTOPIA port. Read-disabled queues may be used, as large external memory, to store cells bound for the microprocessor. The microprocessor may use as many queues as required for different type cells. Because the microprocessor reads only 2 bytes from the SDRAM per access, the cas2pre value (see Section 11.3, SDRAM Interface Timing) may need to be larger than that required for the transferring of cells only. Therefore, to maximize the bandwidth of the SDRAM for cell bus to UTOPIA traffic, restrict microprocessor access of the SDRAM to the initialization function (e.g., downloading microcode over the cell bus).

When the microprocessor increments the read pointer to read the SDRAM, it must first write the three least significant bits (rd_pntX[8:6]) of the read pointer for the appropriate queue followed by the 16 most significant bits (rd_pntX[24:9]). This order must be followed for proper operation. All queues used for microprocessor cell reception must be at least 32 cells long. (See the Queue X Definition Structure, Table 1 19, for more information on these bits.)

11.5 SDRAM Refresh

The T8207 SDRAM interface performs CAS before RAS (CBR) refresh commands at a rate programmed in the ref_cnt bits of the refresh register (address 0410h). The value in the refresh register represents refresh cycles in SDRAM clock cycles. One refresh command is executed every ref_cnt clock cycles, on average, when the SDRAM is idle. In addition, the value programmed in the refresh lateness register (address 0412h) represents the maximum time, in programmed refresh cycles, between actual refresh cycles. If this limit is exceeded, the ref_late bit in the SDRAM interrupt status register (address 0402h) will be set, and if the ref_late interrupt is enabled, an interrupt will be generated. The ref_late indication is provided for diagnostic purposes and does not necessarily indicate a fatal error. Bit errors in the actual cell are reported in the crc8_err_even and crc8_err_odd bits of the SDRAM interrupt status register.

Agere Systems Inc. 73

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

11 SDRAM Interface (continued)

11 .6 SDRAM Throughput

The SDRAM clock frequency must be fast enough for cell transfers, to and from the SDRAM, to occur without overruns to the TX PHY FIFO or underruns to the TX UTOPIA cell buffer. Using the default values for ras2cas, cas2pre, and pre2cmd, thirty-five clock cycles are required to transfer one cell (56 bytes) into or out of the SDRAM. The assumed efficiency rate is 90%. Therefore, the number of cells per second that can be read or written into the SDRAM is calculated using the following equation:

Cell Rate = (f

mclk/35 cycles per cell x 90%)

where f

mclk is the frequency of the SDRAM clock.

The maximum UTOPIA and cell bus bandwidths must be calculated to ensure that the SDRAM clock frequency supports these bandwidths. For example, assume that the total bandwidth on the UTOPIA bus is 64 Mbits/s and that the cell bus clock rate is 33 MHz. The maximum number of cells per second that the cell bus can send is:

= 2.06 Mcells per second.

On the UTOPIA port, the total number of cells that can be sent is:

= 151 Kcells per second.

Thus, the total number of cells per second from the cell bus and to the UTOPIA bus is 2.21 Mcells per second. For the cell rate equation above, the required SDRAM clock frequency is:

* 35 cycles per cell = 86 MHz.

This is a worst-case example and assumes that all potential cells on the cell bus are going to this one device. The SDRAM frequency calculation produces a lower frequency if the actual system characteristics are considered and if the distribution of cells is controlled.

33 MHz

16 cycles per cell

--------------------------------------------- -

64 Mbits/s

53 bytes per cell 8 bits per byte×

---------------------------------------------------------------------------------------

2.21 Mcells per second

0.9

-------------------------------------------------------------

74 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

12 Traffic Management

12.1 Cell Loss Priority (CLP)

To avoid congestion, cells with their CLP bit set may be automatically discarded upon reception at the TX PHY FIFO or upon reception at a queue in the SDRAM. The cells are discarded if the TX PHY FIFO or SDRAM queue is filled beyond the programmed limit and this feature is enabled.

For the TX PHY FIFO, this limit is programmed in the clp_fill_limit bits of the main configuration/control register (address 0110h). The feature is enabled when the cell_drop_en bit in the main configuration/control register (address 0110h) is set.

For the SDRAM queues, this limit is programmed for each queue (X) in the clp_fillX[24:9] and clp_fillX[8:6] bits in Table 119. The feature is enabled when the queueX_clp_en bit in the queue X registers (address 0440h through 04BEh) is set. When a received cell exceeds the CLP fill level for a queue, the T8207 sets the corresponding queueX_clp_lim status bit in the queue X registers. If the fill level is set to zero, the corresponding queueX_clp_lim bit is set by the first received cell for the queue. Any fill greater than zero has an inherent inaccuracy of seven cells; therefore, a fill limit of eight or less is not meaningful. The number of cells in each queue may be determined by reading the value of the read and write pointers for the specific queue.

12.2 Forward Explicit Congestion Notification (FECN)

The T8207 supports FECN for data cells using the explicit forward congestion indication (EFCI) bit in the cell header PTI. If enabled, FECN indicates cells that have encountered congestion by setting their EFCI bit. The T8207 sets the EFCI bit in cells that leave a queue that is filled beyond the limit programmed in the fecn_fillX[24:9] and fecn_fillX[8:6] bits in Table 119. (See Figure 12.) The T8207 only sets the EFCI bit in cells when the function is enabled by the queueX_fecn_en bit in the queue X registers (address 0440h through 04BEh). When a received cell exceeds the FECN fill level for a queue, the T8207 sets the corresponding queueX_fecn_lim status bit in the queue X registers. If the fill level is set to zero, the corresponding queueX_fecn_lim bit is set by the first received cell for the queue. Any fill greater than zero has an inherent inaccuracy of seven cells; therefore, a fill limit of eight or less is not meaningful. The number of cells in each queue may be determined by reading the value of the read and write pointers for the specific queue.

12.3 Partial Packet Discard (PPD)

Partial packet discard (PPD) is accomplished through the cooperation of the T8207 (source) that places the cell on the cell bus and the T8207 (destination) that receives the cell from the bus. The source T8207 uses its translation RAM to place a unique ID (PPD pointer) and PPD enable bit in the cell for each AAL5 connection. The PPD pointer and PPD enable bit may consist of any bit in the first 64 bits of the bus cell (cell bus routing header, tandem routing header, and ATM cell header) and are created at connection establishment.

The destination T8207 uses the PPD state memory (address 1000h to 13FEh) to track the state of AAL5 virtual channels for partial packet discard. Each bit in the memory represents one of 8192 potential AAL5 virtual channels. When the virtual channel connection is initially established, the bit in PPD state memory pointed to by the PPD pointer is cleared. When a cell that has its PPD enabled is discarded, the bit pointed to by the PPD pointer becomes set. Once this bit is set, successive cells with the same PPD pointer will be discarded until the last cell is received. The last cell is identified using the SDU-type bit in the PTI of the cell header. When the last cell of the packet is received, the virtual channel’s corresponding bit in the PPD state memory is automatically cleared, and the last cell is transmitted.

The ppd_en_sel[5:0] bits in the PPD information 1 register specify which of the bus cell’s first 64 bits (cell bus routing header, tandem routing header, and ATM cell header) enable PPD. PPD is enabled when the associated bit in the headers is one. The partial packet discard bits specify which of the bus cell’s first 64 bits are used to create the PPD pointer. These pointer bits are ppd_pnt0_sel[5:0] through ppd_pnt12_sel[5:0] in the PPD information 1 through 7 registers (addresses 0206h through 0212h). When an AAL5 virtual channel connection is initially established, its PPD bit in the PPD state memory must be cleared using the write_pul, write_val, and write_addr bits in the PPD memory write register at address 0418h.

Agere Systems Inc. 75

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

13 JTAG Test Access Port

A 5-pin test access port, consisting of the jtag_tclk, jtag_tms, jtag_tdi, jtag_tdo, and jtag_trst signals, provides the standard interface to the test logic. The jtag_trst signal is active-low and resets the JTAG circuitry . When jtag_trst is high, the JTAG interface is enabled. If the JTAG port is not used, jtag_trst should be tied low.

JT AG may be used only to test the inputs, outputs, and their connection to the printed-wiring board. In JTAG, serial bit patterns are shifted into the device through the jtag_tdi pin, and the results can be observed at the I/O and at the corresponding JTAG serial output, jtag_tdo. Since this JTAG conforms to the JTAG standard, the jtag_tdi and jtag_tdo may be linked to the JTAG port of other devices for systemic testing. The boundary-scan description language may be found on the Agere website.

13.1 Instruction Register

The instruction register (IR) is 3 bits in length. The instructions are defined in Table 21.

T able 21. Instruction Register

Instruction Binary Code Description

EXTEST “000” Places the boundary-scan registe r in exte st mode.

SAMPLE “ 00 1” Places the boundar y -sc an re gis te r in sampl e mode.

Reserved “010”—“110” R es erve d.

BYPASS “111” Places the bypass register in the scan chain.

76 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

13 JTAG Test Access Port (continued)

13.2 Boundary-Scan Register

The boundary-scan register (BSR) is 222 bits in length. Table 22 gives descriptions of each cell in the boundaryscan chain beginning with the least significant bit.

Table 22. Boundary-Scan Register Descriptions

Boundary-Scan

Name Pin Name Description

0—4 UA_N(0:4) ua*[0:4] Input.

5 ENARB_OE

—

ENARB is an input when ENARB_OE = 0. 6 ENARB arb_enb* Bidirectional. 7CKOE_IN

—

CKO is high impedance when CKOE_IN = 0. 8 CKO cko 3-statable output. 9 CKOE cko_e Input.

10 GPIO_OE(0)

—

GPIO(0) is an input when GPIO_OE(0) = 0.

11 GPIO(0) gpio[0] Bidirectional. 12 GPIO_OE(1)

—

GPIO(1) is an input when GPIO_OE(1) = 0.

13 GPIO(1) gpio[1] Bidirectional. 14 GPIO_OE(2)

—

GPIO(2) is an input when GPIO_OE(2) = 0.

15 GPIO(2) gpio[2] Bidirectional. 16 GPIO_OE(3)

—

GPIO(3) is an input when GPIO_OE(3) = 0.

17 GPIO(3) gpio[3] Bidirectional. 18 GPIO_OE(4)

—

GPIO(4) is an input when GPIO_OE(4) = 0.

19 GPIO(4) gpio[4] Bidirectional. 20 GPIO_OE(5)

—

GPIO(5) is an input when GPIO_OE(5) = 0.

21 GPIO(5) gpio[5] Bidirectional. 22 GPIO_OE(6)

—

GPIO(6) is an input when GPIO_OE(6) = 0.

23 GPIO(6) gpio[6] Bidirectional. 24 GPIO_OE(7)

—

GPIO(7) is an input when GPIO_OE(7) = 0.

25 GPIO(7) gpio[7] Bidirectional. 26 MUX mux Input. 27 RESET_N reset* Input. 28 CB_ACK_N cb_ack* Bidirectional.

29—60 CB_D_N(0:31) cb_d*[0:31] Bidirectional.

61 CB_F_N cb_fs* Bidirectional. 62 CB_DISBL cb_disable* Input. 63 CB_RC_N cb_rc* Input. 64 CB_WC_N cb_wc* Input.

65—72 A(0:7) a[0]/ale,

a[1:7]

Input.

73 D_OE — D(0:7) are inputs when D_OE = 0.

74—81 D(0:7) d[0:7] Bidirectional.

82 MOTO mot_sel Input. 83 RD_WR_N rd*_rw* Input.

Agere Systems Inc. 77

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

13 JTAG Test Access Port (continued)

Table 22

. Boundary-Scan Register Descriptions (continued)

Boundary-Scan

Name Pin Name Description

84 RDY_DTACK_N_OE

—

RDYDTACK is high impedance when

RDY_DTACK_N_OE = 0. 85 RDYDTACK rdy_dtack* 3-statable output. 86 SEL_N sel* Input. 87 WR_N wr*_ds* Input. 88 DEVHIZ_N_HIGH_DRIVE

—

INT_IRQ, SD_A(11:0), SD_BS(1:0), SD_CAS_N,

SD_RAS_N, and SD_WE_N are high impedance

when DEVHIZ_N_HIGH_DRIVE = 0. 89 INT_IRQ int_irq* 3-statable output.

90—101 SD_A(0:11) sd_a[0:11] 3-statable output.

102—103 SD_BS(0:1) sd_bs[0:1] 3-statable output.

104 SD_CAS_N sd_cas* 3-statable output. 105 SD_CLK_OE

—

SD_CLK is an input when SD_CLK_OE = 0.

106 SD_CLK sd_clk Bidirectional. 107 SD_D_OE

—

SD_D(15:0) are inputs when SD_D_OE = 0.

108—123 SD_D(0:15) sd_d[0:15] Bidirectional.

124 SD_RAS_N sd_ras* 3-statable output. 125 SD_WE_N sd_we* 3-statable output. 126 TR_CONT_OE

—

TR_OE_N, TR_WE_N, TR_A(17:0), and

TR_CS(1:0) are high impedance when

TR_CONT_OE = 0.

127 TR_OE_N tr_oe* 3-statable output.

128 TR_WE_N tr_we* 3-statable output. 129—146 TR_A(0:17) tr_a[0:17] 3-statable output. 147—148 TR_CS(0:1) tr_cs*[0:1] 3-statable output.

149 TR_D_OE

—

TR_D(7:0) are inputs when TR_D_OE = 0.

150—157 TR_D(0:7) tr_d[0:7] Bidirectional.

158 U_RXADDR_OE

—

U_RXADD(4:0) are inputs when U_RXADDR_OE = 0.

159—163 U_RXADD(0:4) u_rxaddr[0:4] Bidirectional.

164 U_RXCLAV0_OE

—

U_RXCLV0 is an input when U_RXCLAV0_OE =

165 U_RXCLV0 u_rxclav[0] Bidirectional. 166—168 U_RXCLV1—U_RXCLV3 u_rxclav[1:3] Input.

169 U_RXCLK_OE — U_RXCLK is an input when U_RXCLK_OE = 0.

170 U_RXCLK T1 Bidirectional. 171—178 U_RXDAT(0:7) u_rxdata[0:7] Input.

179 U_RXENB0_OE — U_RXENB(0) is an input when U_RXENB0_OE =

78 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

13 JTAG Test Access Port (continued)

Table 22

. Boundary-Scan Register Descriptions (continued)

Boundary-Scan

Name Pin Name Description

180 U_RXENB(0) u_rxenb*[0] Bidirectional. 181 U_RXENB_OE

—

U_RXENB(3:1) are inputs when U_RXENB_OE =

182—184 U_RXENB(1) –

U_RXENB(3)

u_rxenb*[1:3] Bidirectional.

185 U_RXPRTY u_rxprty Input. 186 U_RXSOC u_rxsoc Input. 187 U_SHR_I u_shr_i Input. 188 U_SHR_O_OE — U_SHR_O is an input when U_SHR_O_OE = 0.

189 U_SHR_O u_shr_o Bidirectional. 190 U_TXADDR_OE

—

U_TXADD(4:0) are inputs when U_TXADDR_OE = 0.

191—195 U_TXADD(0:4) u_txaddr[0:4] Bidirectional.

196 U_TXCLAV0_OE

—

U_TXCLV0 is an input when U_TXCLAV0_OE =

197 U_TXCLV0 u_txclav[0] Bidirectional.

198—200 U_TXCLV1 – U_TXCLV3 u_txclav[1:3] Input.

201 U_TXCLK_OE — U_TXCLK is an input when U_TXCLK_OE = 0. 202 U_TXCLK u_txclk Bidirectional. 203 U_TXDATA_OE

—

U_TXDAT(7:0) are high impedance when U_TXDATA_OE = 0.

204—211 U_TXDAT(0:7) u_txdata[0:7] 3-statable output.

212 U_TXENB0_OE

—

U_TXENB0 is an input when U_TXENB0_OE = 0. 213 U_TXENB0 u_txenb*[0] Bidirectional. 214 U_TXENB_OE

—

U_TXENB1, U_TXENB2, and U_TXENB3 are

high impedance when U_TXENB_OE = 0.

215—217 U_TXENB1 – U_TXENB3 u_txenb*[1:3] 3-statable output.

218 U_TXPRTY_OE — U_TXPRTY is an input when U_TXPRTY_OE =

0. 219 U_TXPRTY u_txprty Bidirectional. 220 U_TXSOC_OE

—

U_TXSOC is high impedance when U_TXSOC_OE = 0.

221 U_TXSOC u_txsoc 3-statable output.

Agere Systems Inc. 79

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers

The T8207 has two distinct memory spaces, which are the direct memory access registers and the extended memory registers. The direct memory access registers are directly addressed 8-bit (byte) registers and are mapped between addresses 00h and FFh. The extended memory registers are indirectly addressed and mapped between addresses 0100h and 3FFFFFEh. The extended memory registers are mapped into three major blocks: the main registers, the UTOPIA registers, and the SDRAM registers. They contain the SDRAM memory, the translation

RAM, internal memories, and the device’s configuration, status, and control registers. Extended memory registers are 16 bits wide. All accesses to the extended memory registers are executed internally as 16 bits. Direct memory access registers are located in Section 14.2, Direct Memory Access Registers, and extended memory registers are located in Section 14.3, Extended Memory Registers.

14.1 Register Types

Ta ble 23. Register Map

Read/Write (RW):

These registers may be written or read.

Read Only (RO): These registers may only be read. Read-Only Latch (ROL): The read-only latch is used for interrupt status registers. Reading a read-only latch

register has no effect on the contents. To clear a bit set in an ROL register, a one must be written to the bit. Writing a zero to the bit has no effect. If the corresponding interrupt enable bit is set, an interrupt will be continuously generated until the bit in the ROL register is cleared.

Write Only (WO): These registers may only be written. The write-only registers in the T8207 are a

pulse type. When they are written to one, they generate a pulse internally for one clock cycle and then return to zero.

Direct Configuration/Control Register (DCCR) 28h

Interrupt Service Request (ISREQ) 29h

mclk PLL Configuration 0 (MPLLCF0) 2Ah

mclk PLL Configuration 1 (MPLLCF1) 2Bh

GTL+ Slew Rate Configuration (GTLSRCF) 2Eh

GTL+ Control (GTLCNTRL) 2Fh

Extended Memory Address 1 (Little Endian) (EMA1_LE) 30h

Extended Memory Address 2 (Little Endian) (EMA2_LE) 31h

Extended Memory Address 3 (Little Endian) (EMA3_LE) 32h

Extended Memory Address 4 (Little Endian) (EMA4_LE) 33h

Extended Memory Access (Little Endian) (EMA_LE) 34h

Extended Memory Data Low (Little Endian) (EMDL_LE) 36h 87 Extended Memory Data High (Little Endian) (EMDH_LE) 37h 87 Extended Memory Address 4 (Big Endian) (EMA4_BE) 30h 88 Extended Memory Address 3 (Big Endian) (EMA3_BE) 31h 88 Extended Memory Address 2 (Big Endian) (EMA2_BE) 32h 88 Extended Memory Address 1 (Big Endian) (EMA1_BE) 33h 88 Extended Memory Access (Big Endian) (EMA_BE) 34h 89 Extended Memory Data High (Big Endian) (EMDH_BE) 36h 89 Extended Memory Data Low (Big Endian) (EMDL_BE) 37h 89 GPIO Output Enable (GPIO_OE) 39h 90 GPIO Output Value (GPIO_OV) 3Bh 90

80 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 23. Register Map

(continued)

GPIO Input Value (GPIO_IV) 3Dh 90 Control Cell Receive Direct Memory (CCRXDM) 60h to 93h 91 Control Cell Transmit Direct Memory (CCTXDM) A0h to D7h 91 PHY Port 0 and Control Cells Multicast Direct Memory (PP0MDM) E0h to FFh 92 Main Configuration 1 (MCF1) 0100h 93 Main Interrupt Status 1 (MIS1) 0102h 94 Main Interrupt Enable 1 (MIE1) 0104h 95 TX UTOPIA Clock Configuration (TXUCCF) 010Ch 96 RX UTOPIA Clock Configuration (RXUCCF) 010Eh 97 Main Configuration/Control (MCFCT) 0110h 98 Main Configuration 2 (MCF2) 0112h 99 UTOPIA Configuration (UCF) 0114h 100 Main Configuration 3 (MCF3) 0116h 100 Loopback (LB) 0118h 101 UTOPIA Configuration 3 (UCF3) 011Ah 101 UTOPIA Configuration 2 (UCF2) 011Ch 101 Extended LUT Configuration (ELUTCF) 011Eh 101 Extended LUT Control (ELUTCN) 0120h 102 Cell Bus Configuration/Status (CBCFS) 0130h 103 Main Interrupt Status 2 (MIS2) 0132h 103 Main Interrupt Enable 2 (MIE2) 0134h 104 Misrouted LUT 1 (MLUT1) 0142h 105 Misrouted LUT 2 (MLUT2) 0144h 105 Misrouted Cell Header High (MCHH) 0146h 105 Misrouted Cell Header Low (MCHL) 0148h 105 Master Queue 3 (MQ3) 0158h 108 Master Queue 2 (MQ2) 015Ah 108 Master Queue 0 (MQ0) 015Ch 109 Master Queue 1 (MQ1) 015Eh 109 Slave Queue 0 (SQ0) 016Ch 110 Slave Queue 1 (SQ1) 016Eh 110 TX PHY FIFO Routing 3 (TXPFR3) 0178h 111 TX PHY FIFO Routing 2 (TXPFR2) 017Ah 112 TX PHY FIFO Routing 0 (TXPFR0) 017Ch 113 TX PHY FIFO Routing 1 (TXPFR1) 017Eh 114 Routing Information 1 (RI1) 0200h 115 Routing Information 2 (RI2) 0202h 116 Routing Information 3 (RI3) 0204h 117 PPD Information 1 (PPDI1) 0206h 118 PPD Information 2 (PPDI2) 0208h 119 PPD Information 3 (PPDI3) 020Ah 120 PPD Information 4 (PPDI4) 020Ch 121 PPD Information 5 (PPDI5) 020Eh 122

Agere Systems Inc. 81

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Ta ble 23. Register Map

(continued)

PPD Information 6 (PPDI6) 0210h 123 PPD Information 7 (PPDI7) 0212h 124 PPD Memory Write (PPDMW) 0418h 124 HEC Interrupt Status 1 (HIS1) 0302h 106 HEC Interrupt Enable 1 (HIE1) 0304h 106 HEC Interrupt Status (HIS) 0306h 106 HEC Interrupt Enable (HIE) 0308h 106 LUT Interrupt Service Request (LUTISR) 030Eh 106 LUT X Configuration/Status (LUTXCFS) 0320h to 033Eh 107 SDRAM Control (SCT) 0400h 128 SDRAM Interrupt Status (SIS) 0402h 128 SDRAM Interrupt Enable (SIE) 0404h 128 SDRAM Configuration (SCF) 0408h 129 Refresh (RFRSH) 0410h 130 Refresh Lateness (RFRSHL) 0412h 130 Idle State 1 (IS1) 0420h 130 Idle State 2 (IS2) 0422h 130 Manual Access State 1 (MAS1) 0424h 131 Manual Access State 2 (MAS2) 0426h 131 SDRAM Interrupt Service Request 4 (SISR4) 0438h 132 SDRAM Interrupt Service Request 3 (SISR3) 043Ah 132 SDRAM Interrupt Service Request 1 (SISR1) 043Ch 132 SDRAM Interrupt Service Request 2 (SISR2) 043Eh 132 Queue X (QX) 0440h to 04BEh 133 PHY Port X Transmit Count Structure (PPXTXCNT) 0600h to 067Ch 125 PHY Port X Receive Count Structure (PPXRXCNT) 0700h to 07F8h 126 LUT X Configuration 1 Structure (LUTXCF1) 0704h to 077Ch 127 Control Cell Receive Extended Memory (CCRXEM) 0 0800h to 0832h 137 Control Cell Transmit Extended Memory (CCTXEM) 0900h to 0936h 137 PHY Port 0 and Control Cells Multicast Extended Memory (PP0MEM) 0C00h to 0C1Eh 138 PHY Port X Multicast Memory (PPXMM) 0C20h to 0DE0h 139 PPD Memory (PPDM) 1000h to 13FEh 140 Queue X Definition Structure (QXDEF) 2000h to 27E0h 135 Translation RAM Memory (TRAM) 100000h to 17FFFEh 141 SDRAM (SDRAM) 2000000h to

3FFFFFEh

141

82 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2 Direct Memory Access Registers

The direct memory access registers are the only registers that can be directly addressed. These registers provide some status and initial control of the device. In addition, the direct memory access register set includes some extended memory access registers, which are used to indirectly access the extended memory registers. All unde-

fined addresses in the direct memory access registers’ memory map, 00h to FFh, are reserved and should not be accessed.

Table 24. Identification 0 (IDNT0) (00h)

Table 25. Identification 1 (IDNT1) (01h)

Table 26. Identification 2 (I DNT2) (02h)

1. RN represents the current revision number of the device.

Name Bit Pos. Type Reset Description

Device ID 0 7:0 RO 4Fh Device Identification 0.

Name Bit Pos. Type Reset Description

Device ID 1 7:0 RO 07h Device Identification 1.

Name Bit Pos. Type Reset Description

Device ID 2 7:0 RO RN

Revision Number.

Agere Systems Inc. 83

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 27. Direct Configuration/Control Register (DCCR) (28h)

Name Bit Pos. Type Reset Description

cyc_per_acc 0 RW 0

Cycles Per Access. This bit is used to indicate the number of cycles per read/write to the translation RAM.

‘0’

= 2 mclk cycles.

‘1’

= 3 mclk cycles.

srst_reg* 1 RW 0 Software Reset Main Registers. A logic level zero on this bit resets

the main registers only. The direct memory access registers (including this one) are not affected by this reset. This bit must be ‘0’ while the mclk PLL configuration 0 and 1 registers are being modified. Activelow.

srst* 2 RW 0 Software Reset. A logic level zero on this bit resets the entire device

except the direct memory registers and the main registers. This bit must be ‘0’ while the mclk PLL configuration 0 and 1 registers are being modified and clocks are not present. Active-low.

Reserved 3 RW 0 Reserved. This bit must be programmed to ‘1.’

rplc_gfc 4 RW 0 Replace GFC. If this bit is ‘1’ and the device is in UNI mode, the GFC

field of incoming cells will be replaced during a VPI-VCI translation. If this bit is ‘0’ and the device is in UNI mode, the GFC field will be left untouched. When the device is in NNI mode or when a VPI only translation is performed, this bit has no effect.

big_end 5 RW 0 Big Endian. If this bit is ‘0,’ register fields in the direct address space,

30h to 37h, will be in little-endian format. If ‘1,’ fields in the direct address space, 30h to 37h, will be in big-endian format.

Reserved 7:6 RW 0 Reserved. These bits must be programmed to ‘0.’

84 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 28. Interrupt Service Request (ISREQ) (29h)

Table 29. mclk PLL Configuration 0 (MPLLCF0) (2Ah)

Name Bit Pos. Type Reset Description

Reserved 0 RO 0

Reserved.

int_serv_mainreg 1 RO 0 Interrupt Service Request for Main Registers. When this bit is

‘1,’ an interrupt in the main register group of the extended memory registers needs servicing. The control cell sent and control cell available status bits do not affect this bit. Only enabled interrupts will cause this bit to become set.

int_serv_sdramreg 2 RO 0 Interrupt Service Request for SDRAM Registers. When this bit

is ‘1,’ an interrupt in the SDRAM register group of the extended memory registers needs servicing. Only enabled interrupts will cause this bit to become set.

int_serv_utopiareg 3 RO 0 Interrupt Service Request for UTOPIA Registers. When this bit

is ‘1,’ an interrupt in the UTOPIA register group of the extended memory registers needs servicing. Only enabled interrupts will cause this bit to become set.

Reserved 4 RO 0 Reserved.

ctrl_cell_sent_sr 5 RO 0 Control Cell Sent Interrupt Service Request. When this bit is

‘1,’ the control cell sent interrupt in the main interrupt status 1 register needs servicing. The corresponding interrupt does not need to be enabled for this bit to become set.

ctrl_cell_av_sr 6 RO 0 Control Cell Available Interrupt Service Request. When this

bit is ‘1,’ the control cell available interrupt in the main interrupt status 1 register needs servicing. The corresponding interrupt does not need to be enabled for this bit to become set.

Reserved 7 RO 0 Reserved.

Name Bit Pos. Type Reset Description

lf[3:0] 3:0 RW 0

Loop Filter. See Section 5, PLL Configuration, for information on these bits.

Reserved 5:4 RO 0

Reserved.

bypb 6 RW 0 Bypass PLL. If this bit is ‘0,’ the PLL is bypassed. If ‘1,’ the output

of the PLL supplies mclk.

pllen 7 RW 0 PLL Enable. If this bit is ‘1,’ the PLL is enabled. If ‘0,’ the PLL is

disabled.

Agere Systems Inc. 85

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 30. mclk PLL Configuration 1 (MPLLCF1) (2Bh)

Table 31. GTL+ Slew Rate Configuration (GTLSRCF) (2Eh)

Table 32. GTL+ Control (GTLCNTRL) (2Fh)

Name Bit Pos. Type Reset Description

pll_m[4:0] 4:0 RW 0

PLL M Count Value. See Section 5, PLL Configuration, for information on these bits.

pll_n[2:0] 7:5 RW 0 PLL N Count Value. See Section 5, PLL Configuration, for informa-

tion on these bits.

Name Bit Pos. Type Reset Description

slew_rate[2:0] 2:0 RW 4h GTL+ Slew Rate Control [2:0]. The slew rates of the GTL+ (cell bus)

output signals are controlled by these bits. The minimum slew rate time is 0.9 ns and the maximum slew rate time is 3.8 ns.

“000” = Fastest slew rate “001” “010” “011” = Nominal slew rate (on fast side) “100” = Nominal slew rate (on slow side) “101” “110”

“111” = Slowest slew rate Reserved 3 RW 1 Reserved. Program to ‘1.’ Reserved 7:4 RW 0 Reserved. Program to ‘0.’

Name Bit Pos. Type Reset Description

Reserved 0 R 1 Reserved. Program to ‘1.’

GTLRPDN 1 RW 1 GTL+ Receive Powerdown. When this bit is cleared to ‘0,’ the

GTL+ receivers on the cell bus pins are powered down. Under this condition, no cells can be received from the backplane.

When this bit is set to ‘1,’ the GTL+ receivers are powered up and cells are received from the backplane.

GTLTPDN 2 RW 1 GTL+ Transmit Powerdown. When this bit is cleared to ‘0,’

the GTL+ transmitters on the cell bus pins are powered down. Under this condition, no cells can be transmitted to the backplane.

When this bit is set to ‘1,’ the GTL+ transmitters are powered

up and cells are transmitted to the backp la ne. Reserved 4:3 R 0 Reserved. Program to ‘0.’ Reserved 5 R 1 Reserved. Program to ‘1.’ Reserved 7:6 R 0 Reserved. Program to ‘0.’

86 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2.1 Little-Endian Format (big_end = 0) for Extended Memory Access Registers 30h—37h

Table 33. Extended Memory Address 1 (Little Endian) (EMA1_LE) (30h)

Table 34. Extended Memory Address 2 (Little Endian) (EMA2_LE) (31h)

Table 35. Extended Memory Address 3 (Little Endian) (EMA3_LE) (32h)

Table 36. Extended Memory Address 4 (Little Endian) (EMA4_LE) (33h)

Table 37. Extended Memory Access (Little Endian) (EMA_LE) (34h)

Name Bit Pos. Type Reset Description

Reserved 4:0 RO 0

Reserved.

ext_a[8:6] 7:5 RW 0

Extended Access Address [8:6]. This extended access register points to words.

Name Bit Pos. Type Reset Description

ext_a[16:9] 7:0 RW 0

Extended Access Address [16:9]. This extended access register points to words.

Name Bit Pos. Type Reset Description

ext_a[24:17] 7:0 RW 0

Extended Access Address [24:17]. This extended access register points to words.

Name Bit Pos. Type Reset Description

ext_a[25] 0 RW 0

Extended Access Address [25]. This extended access register points to words.

Reserved 7:1 RO 0 Reserved.

Name Bit Pos. Type Reset Description

ext_a[5:1] 4:0 RW 0

Extended Access Address [5:1]. This extended access register points to words. ext_a[0] is

hardwired to ‘0.’

ext_we[1:0] 6:5 RW 0

Extended Access Write Enable. These bits are active-high write enables for word accesses. If both bits are low, a read is performed. If ext_we[1] is high, the contents of ext_d[15:8] are written, and if ext_we[0] is high, the contents of ext_d[7:0] are written. If both bits are high, both data bytes are written.

ext_strt_acc 7 RW 0 Start Access to Extended Memory. Write a ‘1’ to this bit to start the

access to the extended memory registers. This bit is automatically cleared when the access is complete.

Agere Systems Inc. 87

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 38. Extended Memory Data Low (Little Endian) (EMDL_LE) (36h)

Table 39. Extended Memory Data High (Little Endian) (EMDH_LE) (37h)

Name B it Pos. Type Reset Description

ext_d[7:0] 7:0 RW 0

Extended Access Data Low. The least significant byte of data to be written to extended memory is written here before the extended write begins. The least significant byte of data read from extended memory is available here after the extended read is complete.

Name B it Pos. Type Reset Description

ext_d[15:8] 7:0 RW 0

Extended Access Data High. The most significant byte of data to be written to extended memory is written here before the extended write begins. The most significant byte of data read from extended memory is available here after the extended read is complete.

88 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2.2 Big-Endian Format (big_end = 1) for Extended Memory Access Registers 30h—37h

Table 40. Extended Memory Address 4 (Big Endian) (EMA4_BE) (30h)

Table 41. Extended Memory Address 3 (Big Endian) (EMA3_BE) (31h)

Table 42. Extended Memory Address 2 (Big Endian) (EMA2_BE) (32h)

Table 43. Extended Memory Address 1 (Big Endian) (EMA1_BE) (33h)

Name Bit Pos. Type Reset Description

ext_a[25] 0 RW 0

Extended Access Address [25]. This extended access register points to words.

Reserved 7:1 RO 0 Reserved.

Name Bit Pos. Type Reset Description

ext_a[24:17] 7:0 RW 0

Extended Access Address [24:17]. This extended access register points to words.

Name Bit Pos. Type Reset Description

ext_a[16:9] 7:0 RW 0

Extended Access Address [16:9]. This extended access register points to words.

Name Bit Pos. Type Reset Description

Reserved 4:0 RO 0

Reserved.

ext_a[8:6] 7:5 RW 0

Extended Access Address [8:6]. This extended access register points to words.

Agere Systems Inc. 89

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

T able 44. Extended Memory Access (Big Endian) (EMA_BE) (34h)

T able 45. Extended Memory Data High (Big Endian) (EMDH_BE) (36h)

Table 46. Extended Memory Data Low (Big Endian) (EMDL_BE) (37h)

Name Bit Pos. Type Reset Description

ext_a[5:1] 4:0 RW 0 Extended Access Address [5:1]. This extended access register points

to words. ext_a[0] is hardwired to ‘0.’

ext_we[1:0] 6:5 RW 0

ext_strt_acc 7 RW 0

Start Access to Extended Memory. Write a ‘1’ to this bit to start the access to the extended memory registers. This bit is automatically cleared when the access is complete.

Name Bit Pos. Type Reset Description

ext_d[15:8] 7:0 RW 0

Name Bit

Pos.

Type Reset Description

ext_d[7:0] 7:0 RW 0

90 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2.3 General-Purpose I/O Control Registers

Table 47. GPIO Output Enable (GPIO_OE) (39h)

Table 48. GPIO Output Value (GPIO_OV) (3Bh)

Table 49. GPIO Input Value (GPIO_IV) (3Dh)

Name Bit Pos. Type Reset Description

GPIO_oe[7:0] 7:0 RW 0

GPIO Output Enable. If this bit is set to

‘1,’ the corresponding GPIO pin is an output. If cleared to ‘0,’ the corresponding GPIO pin is an input.

Name Bit Pos. Type Reset Description

GPIO_out[7:0] 7:0 RW 0

GPIO Output Buffer. Output bits for the GPIO[7:0] pins are written to this buffer. A bit in this buffer is only written to the pin if the corresponding output enable bit is high.

Name Bit Pos. Type Reset Description

GPIO_in[7:0] 7:0 RO 0

GPIO Input Buffer. This buffer contains the values at the GPIO[7:0] pins.

Agere Systems Inc. 91

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2.4 Control Cells

T able 50. Control Cell Receive Direct Memory (CCRXDM) (60h to 93h)

The control cell receive memory may also be accessed from extended memory. See Table 120.

Table 51. Control Cell Transmit Direct Memory (CCTXDM) (A0h to D7h)

The control cell transmit memory may also be accessed from extended memory. See Table 121.

Name Offset Type Reset Description

header[31:24] 00h RO X These 52 bytes are the control cell received from the

cell bus. This memory space in direct memory is a shadow of the control cell receive extended memory. When present, the control cell should be read from this direct memory space.

header[23:16] 01h header[15:8] 02h header[7:0] 03h payload_byte0 04h payload_byte1 05h

. . .

. .

. payload_byte46 32h payload_byte47 33h

Name Offset Type Reset Description

cell_bus_routing_header[15:8] 00h RW X These 56 bytes are the cell routing header, the tan-

dem routing header, and the control cell to be transmitted onto the cell bus. This memory space in direct memory is a shadow of the control cell transmit extended memory. A control cell to be transmitted should be written to this direct memory space.

cell_bus_routing_header[7:0] 01h tandem_routing_header[15:8] 02h tandem_routing_header[7:0] 03h header[31:24] 04h header[23:16] 05h header[15:8] 06h header[7:0] 07h payload_byte0 08h payload_byte1 09h

. . .

. payload_byte46 36h payload_byte47 37h

92 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

14.2.5 Multicast Memories

Table 52. PHY Port 0 and Control Cells Multicast Direct Memory (PP0MDM) (E0h to FFh)

The PHY port 0 and control cells multicast memory may also be accessed from extended memory (see Table 122).

Name Offset Type Reset Description

multicast_receive_enable[15:0] 00h RW X This memory space contains 256 active-high

enable bits. Each bit represents a multicast net number from 0 through 255. If a bit is set, the corresponding multicast addressed data cell is sent to the queue group for PHY port 0, or the corresponding multicast control cell is sent to the control cell receive direct and extended memory. The least significant bit is multicast net number 0. This memory space in direct memory is a shadow of the PHY port 0 and control cells multicast extended memory space.

multicast_receive_enable[31:16] 02h multicast_receive_enable[47:32] 04h

. . .

. .

. multicast_receive_enable[159:144] 12h multicast_receive_enable[175:160] 14h multicast_receive_enable[191:176] 16h multicast_receive_enable[207:192] 18h multicast_receive_enable[223:208] 1Ah multicast_receive_enable[239:224] 1Ch multicast_receive_enable[255:240] 1Eh

Agere Systems Inc. 93

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14Registers (continued)

14.3Extended Memory Registers

The

CelXpres

T8207’s extended memory registers are mapped into three major blocks: the main registers, the

UTOPIA registers, and the SDRAM registers.

14.3.1Main Registers

Table 53. Main Configuration 1 (MCF1) (0100h)

Name Bit Pos.Type Reset Description

Reserved 7:0 RO 00h

Reserved.

tx_utopia_hi_z 8 RW 0

Transmit UTOPIA High Impedance. When the device is in ATM

and shared UTOPIA mode, this bit must be cleared to ‘0’:

■For the slave device, the u_txsoc output will always be high

impedance while the u_txdata[7:0] and u_txprty outputs go high impedance when not active.

■For the master device, the u_txdata[7:0] and u_txprty outputs go

high impedance when not active.

When the device is in ATM and nonshared UTOPIA mode and this

bit is cleared to ‘0,’ the u_txdata[7:0] and u_txprty outputs go high impedance when not active.

When the device is in PHY mode and this bit is cleared to ‘0,’ the u_txsoc, u_txdata[7:0], and u_txprty outputs go high impedance when not active. If the device acts as one of the multi-PHY devices, then this bit must be cleared to ‘0.’

When this bit is set to ‘1,’ the u_txsoc, u_txdata[7:0], and u_txprty outputs never go high impedance.

sdram_bypass 9RW0SDRAM Bypass.

When this bit is ‘1,’ the T8207 will not use SDRAM and will use only internal memory to buffer cell bus data. Clear this bit to enable the SDRAM interface. Only queue 0 is used when the SDRAM is bypassed.

phyen

10 RW 1 PHY Enable.

When this bit is ‘1,’ the UTOPIA bus is configured for ATM mode. When ‘0,’ the UTOPIA bus is configured for PHY mode.

tram_qnty_sel

11 RW 0 Translation RAM Quantity Select.

When two external SRAM devices are used, this bit should be set. When this bit is cleared, only one external SRAM will be accessed using tr_cs*[0].

sp_utopia_sel 12 RW 1 Special UTOPIA Mode Select. When this bit is ‘1,’ the T8207 will

send 53-byte cells on the UTOPIA bus. When it is ‘0,’ the 55-byte UTOPIA mode is selected, and the tandem routing header bytes will be appended to the beginning of each cell.

tram_size 14:13 RW 0 Translation RAM Size. These bits identify the size of the external

SRAM used for the look-up table RAM. “00” = 32K bytes

“01” = 64K bytes “10” = 128K bytes “11” = 256K bytes

Reserved 15 RW 0 Reserved. Program to ‘0.’

94 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 54. Main Interrupt Status 1 (MIS1) (0102h)

Note: Immediately following device setup, write FFFFh to this register to clear erroneously set bits.

Name Bit Pos. Type Reset Description

cb_wc_miss 0 ROL 0

Cell Bus Write Clock Missing. This bit is set when the cell bus write clock is inactive for 32 mclk cycles. An interrupt is generated if the corresponding enable bit is set.

cb_rc_miss 1 ROL 0 Cell Bus Read Clock Missing. This bit is set when the cell bus read

clock is inactive for 32 mclk cycles. An interrupt is generated if the corresponding enable bit is set.

cb_fs_miss 2 ROL 0 Cell Bus Frame Synchronization Signal Missing. This bit is set

when the cell bus frame sync is not asserted every 16 read clock cycles in 16-user mode, or every 32 read clock cycles in 32-user mode. It is also set when cell bus write clock is not present because the frame synchronization signal is clocked onto the cell bus by the write clock. An interrupt is generated if the corresponding enable bit is set.

BIP8_err 3 ROL 0 Bit Interleave Parity Error. This bit is set when an error is detected in

the BIP-8 field of the last cell bus frame cycle. An interrupt is generated if the corresponding enable bit is set.

ctrl_cell_ack 4 ROL 0

Control Cell Acknowledged. This bit is set when a control cell is sent on the cell bus and an acknowledge is received. This bit is not set for broadcast or multicast cells. An interrupt is generated if the corresponding enable bit is set.

ctrl_cell_nack 5 ROL 0

Control Cell Not Acknowledged. This bit is set when a control cell is sent on the cell bus and an acknowledge is not received. This bit is not set for broadcast or multicast cells. An interrupt is generated if the corresponding enable bit is set.

cb_grnt_to 6 ROL 0 Cell Bus Grant Time-Out. This bit is set when a cell bus request has

not been granted within the time programmed in the cb_req_to bits. An interrupt is generated if the corresponding enable bit is set.

ctrl_cell_sent 7 ROL 0 Control Cell Sent. This bit is set when a control cell is sent onto the

cell bus. An interrupt is generated if the corresponding enable bit is set.

ctrl_cell_av 8 ROL 0 Control Cell Available. This bit is set when a control cell is waiting to

be read by the microprocessor. An interrupt is generated if the corresponding enable bit is set.

cb_rh_crc_err 9 ROL 0 Cell Bus Routing Header CRC Error. This bit is set when an error is

detected in the CRC field of the cell bus routing header. An interrupt is generated if the corresponding enable bit is set.

rx_prty_err 10 ROL 0 Receive Parity Error. This bit is set when the odd parity calculated

over the data received on the RX UTOPIA port does not match the u_rxprty signal. An interrupt is generated if the corresponding enable bit is set. When a receive parity error occurs, the cell is still counted as received and is translated and routed.

soc_err 11 ROL 0 Start of Cell Error. This bit is set when a SOC framing error is

detected on the RX UTOPIA port. An interrupt is generated if the corresponding enable bit is set. When a start of cell error occurs, the received cells are dropped.

Reserved 15:12 RO 0 Reserved.

Agere Systems Inc. 95

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

T able 55. Main Interrupt Enable 1 (MIE1) (0104h)

Name Bit Pos. Type Reset Description

cb_wc_miss_ie 0 RW 0

Cell Bus Write Clock Missing Interrupt Enable. An interrupt is generated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

cb_rc_miss_ie 1 RW 0 Cell Bus Read Clock Missing Interrupt Enable. An interrupt is

generated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

cb_fs_miss_ie 2 RW 0 Cell Bus Frame Synchronization Signal Missing Interrupt

Enable. An interrupt is generated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

BIP8_err_ie 3 RW 0 Bit Interleave Parity Error Interrupt Enable. An int erru pt is gener -

ated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

ctrl_cell_ack_ie 4 RW 0 Control Cell Acknowledged Interrupt Enable. An interrupt is gen-

erated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

ctrl_cell_nack_ie 5 RW 0 Control Cell Not Acknowledged Interrupt Enable. An interrupt is

generated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

cb_grnt_to_ie 6 RW 0 Cell Bus Grant Time-Out Interrupt Enable. An interrupt is gener-

ated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

ctrl_cell_sent_ie 7 RW 0 Control Cell Sent Interrupt Enable. An interrupt is generated if this

bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

ctrl_cell_av_ie 8 RW 0 Control Cell Available Interrupt Enable. An interrupt is generated

if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

cb_rh_crc_err_ie 9 RW 0 Cell Bus Routing Header CRC Error Interrupt Enable. An inter-

rupt is generated if this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

rx_prty_err_ie 10 RW 0 Receive P ar i ty Er ro r I nt e rr up t E n ab le . An interrupt is generated if

this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

soc_err_ie 11 RW 0 Start of Cell Error Interrupt Enable. An interrupt is generated if

this bit and the corresponding status bit are set. The interrupt is generated until this bit or the corresponding status bit is reset.

Reserved 15:12 RO 0 Reserved.

96 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 56. TX UTOPIA Clock Configuration (TXUCCF) (010Ch)

Name Bit Pos. Type Reset Description

tx_utopia_clk_div 7:0 RW 01h

TX UTOPIA Clock Division. The selected TX UTOPIA clock source is divided by the number programmed in these bits as follows:

“00000000” = reserved “00000001” = no division “00000010” = divide by 2 “00000011” = divide by 3

. . .

“11111111” = divide by 255 These bits are meaningful only when the T8207 generates the

TX UTOPIA clock.

tx_utopia_clk_src_sel 9:8 RW 0

TX UTOPIA Clock Source Select. The source of the TX UTOPIA clock is selected via these bits as follows:

“00” = cell bus write clock “01” = reserved “10” = pclk “11” = mclk

These bits are meaningful only when the T8207 generates the TX UTOPIA clock.

Reserved 10 RW 0

Reserved.

Program to ‘0.’

tx_utopia_clk_en 11 RW 0

TX UTOPIA Clock Enable.

If this bit is ‘1,’ the T8207 generates the TX UTOPIA clock on the u_txclk pin. If this bit is ‘0,’ the u_txcl k pin is configured as an input.

Reserved 15:12 RO 0

Reserved.

Agere Systems Inc. 97

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 57. RX UTOPIA Clock Configuration (RXUCCF) (010Eh)

Name Bit Pos. Type Reset Description

rx_utopia_clk_div 7:0 RW 01h

RX UTOPIA Clock Division. The selected RX UTOPIA clock source is divided by the number programmed in these bits as follows:

“00000000” = reserved “00000001” = no division “00000010” = divide by 2 “00000011” = divide by 3

. . .

“11111111” = divide by 255

These bits are meaningful only when the T8207 generates the RX UTOPIA clock.

rx_utopia_clk_src_sel 9:8 RW 0

RX UTOPIA Clock Source Select. The source of the RX UTO

PIA clock is selected via these bits as follows:

“00” = cell bus write clock “01” = reserved “10” = pclk “11” = mclk

These bits are meaningful only when the T8207 ge

nerates the

RX UTOPIA clock.

Reserved 10 RW 0

Reserved.

Program to ‘0.’

rx_utopia_clk_en 11 RW 0

RX UTOPIA Clock Enable.

If this bit is ‘1,’ the T8207 generates the RX UTOPIA clock on the u_rxclk pin. If this bit is ‘0,’ the u_rxclk pin is configured as an input

Reserved 15:12 RO 0

Reserved.

98 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 58. Main Configuration/Control (MCFCT) (0110h)

Table 59. Main Configuration 2 (MCF2) (0112h)

Name Bit Pos. Type Reset Description

cntl_cell_rd 0 WO 0

Control Cell Has Been Read. W

rite ‘1’ to this bit after a control cell is read from the control cell FIFO. The ‘1’ will pulse for one clock cycle and will clear to ‘0’ automatically.

cntl_cell_wr 1 RW 0

Control Cell Written in Control Cell Memory.

Write ‘1’ to this bit

after a control cell is written in the control cell memory. This

bit is

automatically cleared when the cell is transmitted to the cell bus.

cb_req_pr 3:2 RW 0

Cell Bus Request Priority. These bits indicate the priority of standard requests sent on the cell bus as follows:

“00” = disabled, receives cells from cell bus but cannot transmit “01” = low pr iority “10” = medium priority “11” = high priority

clp_fill_limit 10:4 RW 0

CLP Fill Limit. These bits indicate the TX PHY FIFO fill level at which cells with their CLP bit set to one will be discarded.

cell_drop_en 11 RW 0

Cell Drop Enable. If this bit is one, incoming cells with their CLP bit set to one will be discarded when the TX PHY FIFO fill limit programmed in the clp_fill_limit bits is reached.

inv_crc 12 RW 0

Invert CRC. If this bit is one, the CRC-4 in the routing header is inverted before transmission to the cell bus. This bit is used to simulate errors.

cb_rx_en 13 RW 0

Cell Bus Receive Enable.

If this bit is ‘1,’ cells are received from

the cell bus. If ‘0,’ cells are not accepted.

slave_en 14 RW 1

Slave Enable. If this

bit is ‘1,’ the T8207 is configured as a slave in shared UTOPIA mode. The default value of this bit is ‘1.’ Clear this bit if shared UTOPIA is not used. For shared UTOPIA, only one of

the two devices may have this bit cleared. Dynamically changing this bit will cause cell loss.

When this bit is ‘1,’ u_rxenb*[0] and

u_rxenb*[3:1] become inputs.

Reserved 15 RO 0

Reserved.

Name Bit Pos. Type Reset Description

addr_clav_en 2:0 RW 0

UTOPIA Address, Cell Available, and Enable Signals. These bits configure the number of address, cell available, and enable signals on the UTOPIA bus as follows (see Section 9.6 on page 50):

“000” = 0 ADDR, 4 CLAV, 4 ENB “001” = 4 ADDR, 1 CLAV, 1 ENB “010” = 1 ADDR, 4 CLAV, 4 ENB “011” = 4 ADDR, 2 CLAV, 2 ENB

“100” = 2 ADDR, 2 CLAV, 2 ENB “101” = 2 ADDR, 4 CLAV, 4 ENB “110” = 3 ADDR, 1 CLAV, 1 ENB “111” = 3 ADDR, 2 CLAV, 2 ENB

Reserved 3 RO 0 Reserved.

Agere Systems Inc. 99

Advance Data Sheet September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

T able 59. Main Configuration 2 (MCF2) (0112h) (continued)

Name Bit Pos. Type Reset Description

T8207_sel 4 RW 0 T8207 Select Bit. This bit should be programmed to ‘1’ to obtain all of the

T8207 features. If th is b it is p rog ram me d to ‘0, ’ the tw o a ddi tio nal d iv_qu eue bit settings (“100” and “101”) affect its operation. If div_queue is programmed to “100” and the T8207_sel bit is ‘0,’ the TX UTOPIA cell buffer is divided into 64 queues, but only 32 are used. In addition, if this bit is programmed to ‘0,’ the UTOPIA Configuration 3 (011Ah) (Table 63), M aster Queue 3 (0158h) (Table 80), Master Queue 2 (015Ah) (Table 81), TX PHY FIFO Routing 3 (0178h) (Table 86), and TX PHY FIFO Routing 2 (017Ah) (Table 87) registers do not need to be programmed.

dont_inhibit_rxphy

_clav

5RW0Don’t In hibit RX PHY_CLAV. This bit, when set to ‘1,’ ke eps the rx_cla v sig-

nal always asserted high, indicating the capability to accept cells even if the RX UTOPIA FIFO could overrun, or is actually overrun. This bit is valid only when the RX UTOPIA is in PHY mode.

When this bit is cleared to ‘0,’ the rx_clav signal is deasserted if the RX

UTOPIA FIFO is considered full.

inhibit_rxuto_fifo_

overrun

6RW0Inhi bit RX UTO PIA FIFO Overrun. Th is bit, when s et to ‘1,’ p revent s the RX

UTOPIA FIFO from overflowing by deasserting its rx_enb* signal, even though the rx_clav signal is high when polled, if the RX UTOPIA FIFO is considered full. It is considered full when four cells are stored in it that have not yet been read and process ed by the T8207 . This bit is va lid when the R X UTOPIA is in ATM mode.

When this bit is cleared to ‘0,’ the rx_enb* signal is not deasserted even if

the RX UTOPIA FIFO is considered full.

Reserved 7:5 RO 0 Reserved.

div_queue 10:8 RW 0 Divide into Queues. These bits indicate the number of queues used in the

TX UTOPIA cell buffer as follows: “000” = 4 queues—32 cells per queue

“001” = 8 queues—16 cells per queue “010” = 16 queues—8 cells per queue “011” = 32 queues—4 cells per queue “100” = 64 queues—2 cells per queue “101” = 1 queue—128 cells per queue

When the T8 207 is configured to UTOPIA level 1 ATM mode or when it is configured for PHY mode, the number of queues selected should be one to maximize cell buffering.

T8207_sel = 1 (up to 32 PHYs are supported): When the device is configur ed to UTOPIA level 2 ATM mode and is connected to multiple PHY ports, each PHY port uses four queues unless 32 PHY ports are selected. If 32 PHY ports are selected, each PHY port uses two queues. Therefore, for 16 or less PHY ports, selecting four queues will provide only for PHY port 0, selec ting ei ght que ues will provid e only fo r PHY ports 0 and 1, and so on. For 32 PHY ports, selecting four queues will provide only for PHY ports 0 and 1, selecting eight queues will provide only for PHY ports 0, 1, 2, and 3, and so on.

T8207_sel = 0 (up to 16 PHYs are supported): When the device is configur ed to UTOPIA level 2 ATM mode and is connected to multiple PHY ports, each PHY port uses four queues unless 16 PHY ports are selected. If 16 PHY ports are selected, each PHY port uses two queues. Therefore, for 8 or less PHY ports, selecting four queues will provide only for PHY port 0, selec ting ei ght que ues will provid e only fo r PHY ports 0 and 2, and so on. For 16 PHY ports, selecting four queues will provide only for PHY ports 0 and 1, selecting eight queues will provide only for

PHY ports 0, 1, 2, and 3, and so on. Reserved 14:11 RO 0 Reserved. Reserved 15 RW 0 Reserved. Program this bit to ‘1.’

100 Agere Systems Inc.

Advance Data Sheet

September 2001

ATM Interconnect

CelXpres

T8207

14 Registers (continued)

Table 60. UTOPIA Configuration (UCF) (0114h)

Table 61. Main Configuration 3 (MCF3) (0116h)

Name Bit Pos. Type Reset Description

hec_mask 7:0 RW 55h

Header Error Control (HEC) Mask. An exclusive-OR function is performed on these bits and the HEC value received from the UTOPIA bus before the HEC is checked for error. Also, an exclusive-OR function is performed on these bits and the HEC value calculated before it is transmitted on the UTOPIA bus. Note that a value of zero will not change the HEC value, and a value of FFh will invert the HEC value.

addr_match 12:8 RW 0 Address Match. These bits represent the UTOPIA address of the

T8207 in level 2 UTOPIA multi-PHY mode. These bits are only used when the T8207 is configured as a PHY.

Reserved 15:13 RO 0 Reserved.

Name Bit Pos. Type Reset Description

cb_req_to 7:0 RW 0

Cell Bus Request Time-Out. These bits determine the number of frames that a cell bus request may be present before the cell bus grant time-out (cb_grnt_to) status bit is set.

gfc_value 11:8 RW 0 Generic Flow Control (GFC) V alue. These are the bits inserted in

the GFC field of the TX UTOPIA outgoing cells when the GFC insert feature is enabled.

gfc_insert_en 12 RW 0 GFC Insert Enable.

If this bit is ‘1,’ the gfc_value will be inserted

in all cells transmitted to the UTOPIA bus.

Reserved 15:13 RO 0

Reserved.

Lucent Technologies Inc T8207-BAL-DB, T8207-BAL-DT Datasheet

Specifications and Main Features

Frequently Asked Questions

User Manual