Installation Instructions
1 | P a g e V 1 . 0 P u b l i s h e d o n 0 5 . 2 0 1 8
REMIUS LED RECTANGLE TALL BUNKER
SKU# 239406, 239407, 239408
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before using the product, installation and use of this product. Please keep instructions for future
reference.
Warranty
This light fitting is covered by a 3 year warranty. The warranty is from date of purchase, not the date of installation.
Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries
If the fitting is not installed by a licensed electrician it will void the warranty.
Warranty will be void if there is any damage due to improper usage or modification to the fitting.
This light fitting is not suitable for use with dimmer switches. Warranty will be void if the fitting is used on the same
circuit which has a dimmer switch.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation requirements
Must be assembled and installed by a licensed electrician.
All wiring and installation of the light fitting must adhere to local and national wiring rules.
eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
This is a CLASS I fitting and must be earthed during installation.
This fitting is not suitable for use with dimmer switches and should not be used with a circuit which has a dimmer.
This fitting is rated IP65, this must be maintained during wiring and installation.
Select a suitable location for installation:
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure there are no components missing before
assembling.
Check whether the fitting has been damaged during transport. Do not install any product which appears damaged in
any way. Return the complete product to the place of purchase for inspection, repair or replacement.
Ensure power to the circuit you are working on has been switched OFF, before commencing any electrical work.
Installation directions
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within
the packaging material. If assembly is required, place the fitting on a smooth non-scratch surface.
1. Remove the shade from the fitting by loosening the screws. (Fig. B)
2. Use the fitting as a template to mark the screw positions onto the wall. Drill holes into the wall and push the plastic
anchors into the holes.
3. Install the fitting onto the wall by using the mounting screws with rubber ring provided. Check and ensure the anchors
and mounting screws used are suitable for the mounting surface and the surrounding environment. (Fig. C)
4. Remove the terminal block cover by loosening the screw. Connect the mains supply wire to the terminal block.
(Fig. D)
Mains Supply Wire Fitting Wire
Earth – Yellow/Green Yellow/Green
Neutral – Blue or Black Blue
Live – Brown or Red Brown
5. Ensure that the wires are secure and no bare wires are exposed. Install the cover back onto the terminal block and
secure with the screw. (Fig. E)
Installation Instructions
2 | P a g e V 1 . 0 P u b l i s h e d o n 0 5 . 2 0 1 8
6. Select the colour temperature by sliding the adjustable switch. (Fig. E)
7. Install the shade back onto the fitting and secure by tightening the screws. (Fig. F)
8. After the installation, switch on the fitting to test and enjoy your new lighting product.
Safety tips
Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning or
adjustment to the fitting.
The fitting must not be used if the protective shield has been cracked or damaged. Replace any cracked protective
shield.
To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from hazards.
Ensure that the fitting does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the product in water or other liquids.
Specifications
SKU #
239406
239407
239408
Colour
Silver
Black
White
Rated Voltage
220-240V~ 50Hz
Rated Wattage
11W
LEDs
SUNPU, 650LM, 3000K or 4000K
IP Rating
IP65
Weight
0.56kg
Dimensions
H:200mm W:100mm E:70mm
Loading...