Page 1
T Series LED Remote Controller
( T1/T2/T2M/T3/T3M/T3X) This manual applies to:
Dimming
(8 zones)
T1 T2 T2M
Color Temperature
(8 zones)
T3 T3M T3X
RGB Sync Control RGB Zone Control
(10 zones)
RGB ProgrammableColor Temperature
Page 2
Index
General Information
General Information
T1 (Dimming)
T2 (Color Temperature)
T2M (Color Temperature)
T3 (RGB)
T3M (RGB )
T3X (RGB)
After Service
Reset and Edit the Frequency Point
……………………………………………………………
…………………………………………………………
…………………………………………………………
…………………………………………………………
……………………………………………
………………………………………………………
……………………………………………
…………………………………………
……………………………
— 1 —
1~5
~
6 9
~
10 13
~
14 17
~
18 21
~
22 25
~
26 29
30
31
Page 3
A Notice for the Remote Charging:
1.
2.
Charging Completed
For T2/T2M/T3/T3M/T3X
Charging Completed
The remote can be chargeable even at the OFF state, on which the
indicator light is dark.
When charging, please connec t USB cable.
For T1
For T1, the white indicator
light flickers while charging,
and turns lasting light means
the charging is completed.
Fo r T2/T2M/T3/T3M/T3X,
the blue indicator light flickers
whi le c hargin g, and tu rns
green means the charging is
completed.
General Information
3. No memory effect in the lithium battery of remote control. Follow
the standard charging procedure even for the first three times, no
need over charge.
Indicator light flickers meaning low battery and need to be charged.
4.
(red light for T2/T2M/T3/T3M/T3X, white light for T1)
Charging in low battery will affect the life of battery.
For T1
LED indicator flickers
5.
The remote should be full charged and stored at a ventilated and
(White)
means low battery.
For
T2/T2M/T3/T3M/T3X
LED indicator flickers
(Red)
means low battery.
dry place when long time no use, and please full recharge every
3 months.
— 2 —
Page 4
B Technical Specs:
T1/T2/T2M/T3/T3M/T3 X Remote Control
Charging Voltage:
Working Current:
Working Frequency:
RF Remote Distance:
Battery Capacity:
Dimensions:
Package Size:
Weight (G.W.):
55
22
dc
5V (Built-in Lithium Battery)
<30mA
2.4GHz
30m
1000mAh
L145×W55×H22(mm)
L168×W96×H34(mm)
230g
145
T1/T2/T2M/T3/T3M/T3X
60
65
Remote Holder
General Information
T3-CV Receiving Controller
Compatible Remote:
Input Voltage:
Wireless Signal:
Max Current Load:
Max Output Power:
Working Temp.:
Dimensions:
Package Size:
Weight (G.W.):
27
86
T1/T2/T2M/T3/T3M/T3X
5～24Vdc
2.4GHz
6A × 3CH Max 18A
90W/216W/432W(5V/12V/24V)
-30℃～55℃
L175×W44×H30(mm)
L178×W48×H33(mm)
140g
175
44
170
30
T3-CV
— 3 —
Page 5
General Information
T3-CC Receiving Controller (Current 3 in 1)
Compatible Remote:
Wireless Signal:
Input Voltage:
Output Voltage:
Output Current:
Output Power:
Working Temp.:
Dimensions:
Package Size:
Weight (G.W.):
T1/T2/T2M/T3/T3M/T3X
2.4GHz
12～48Vdc
3-46Vdc
CC 350/700/1050mA × 3CH
1.05W～48.3W × 3CH Max 144.9W
-30℃～55℃
L175×W44×H30(mm)
L178×W48×H33(mm)
150g
175
44
170
30
T3-CC
T3-5A Receiving Controller
Compatible Remote Control:
Wireless Signal:
Input Voltage:
Max Current Load:
Max Output Power:
Working Temp.:
Dimensions:
Package Size:
Weight (G.W.):
40
30
— 4 —
T3/T3M/T3X
2.4GHz
12～24Vdc
5A x 3CH Max 15A
180W/360W(12V/24V)
-30℃～55℃
L211×W40×H30(mm)
L215×W43×H33(mm)
165g
211
203
15
16
T3-5A
Page 6
C Terminal of Receivers:
Running Light
Remote ID
Learning Button
dc
5~24V
Power Input
Socket
RUN
CV CONTROLLER
LED Lamp
Connected Socket
12~24V Power Input Socketdc
CV CONTROLLER
General Information
LED Lamp Connected Socket
T3-5A
Running Light
Remote ID
Learning Button
dc
12~48V
Power Input
Socket
Current
Selection Switch
Operation Table
RUN
T3-CV
CC CONTROLLER
T3-CC
LED Lamp
Connected Socket
— 5 —
T3- 5A
On/Off
Mode
Keys
T3-5A
Speed
Keys
Pause
Key
T3- CV T3- CC
Brightness
Keys
Page 7
T1
LED Dimming Controller
LED Dimming Controller (8 Zones)
1. Operation Panel and Component Instruction:
Touch Color Circle
Brightness
Shortcut Keys
Brightness Keys
Sync Status
Indicator Light
T1 remote works with T3-CV, T3-CC receiver.
T1 can realize the signal sync on multiple receivers, zone controlled
arbitrarily (no more than 8 zones) within effective distance, a very good
solution for the LED project needs sync/zone control wirelessly.
Can RF remote the functions of dimming, quick brightness selection
and DIY and so on. User-friendly color wheel for brightness adjustment,
unique LED state light for sync change indicated, user can simply know
the LED working state from distance by checking the remote control.
Scene-mode Keys
M1 M2
(Press for 3s to save the scene
mode in the 8 current zone control.)
Zone Control : Instruction
●
Select one of the zone: press any key of “1-8" on the remote.
●
Select zone control arbitrarily: press" + any number + ",
eg: take 456 as a zone, should press " 456 ".
●
All choose (8 zones): press " " twice.
●
When a zone is under inactive state, press the corresponding zone
No. to light up that zone.
Buzzer on/off: Press “Zone Selection Key” for 3 seconds.
— 6 —
Zone Selection Keys
On/Off
Page 8
2. The Learning ID Method of Remote:
LED Dimming Controller (8 Zones)
Learning ID:
A. Turn on the receiver and remote.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
B.
the running light keeps on, then long press any “1-8" “zone-selection
key” on the T1 remote, the running light returns to flash (the buzzer
long beep, the indicator light flashes 3 times), activated successful.
If installing multiple receivers in one zone, repeat the above steps,
choose the same zone key when ID learning.
T1 remote works with T3-CV, T3-CC receiver.
Canceling ID:
A. Turn on the receiver and remote.
B. Press “ID learning button” on the T3-CC/T3-CV receiver more
than 8s, the buzzer beep twice, delete all the learned remote.
— 7 —
Page 9
LED Dimming Controller (8 Zones)
3. System Diagram:
Unlimited receivers can be installed in per zone within the effective distance, no wiring needed between the receivers, the installed quantity
of LED receivers in per zone can be increased or decreased at any time based on the actual requirements. If you want to increase or
decrease the receivers, just activate or cancel the control ID on the remote control will be fine, no any changes and effects on other receivers.
zone1
zo
n
4
e
e2
e2
zo
n
e3
z
o
n
e
4
z
one1
z
o
ne2
z
o
n
e
1
z
o
ne2
z
one3
z
o
n
e
4
n
o
z
zone1
8
e
n
o
z
7
e
n
o
z
6
e
n
o
z
Centralized Zone-division
n
e
o
z
1
z
o
n
e
2
z
o
n
e
3
z
o
n
e
4
z
o
e 5
n
1
e
zon
4
e
n
o
z
zone3
one2
z
ne1
zon
zone3
2
one
z
o
z
4
e
n
zo
e3
zon
Spacing Zone-division
— 8 —
zone3
zo
n
e4
Page 10
4. Wiring Diagram:
5~24Vdc 5~24Vdc 5~24Vdc
LED Dimming Controller (8 Zones)
12~48Vdc 12~48Vdc 12~48Vdc
CV receiver
T3-CV
Single Color Strip
CV receiver
T3-CV
Single Color Strip
CV receiver
T3-CV
Single Color Strip
CV
……
T3-CC
350mA
Round LED
Panel Light
CC CC
CC receiver
350mA
700mA 700mA 700mA
350mA
LED Panel Light LED Panel Light
— 9 —
CC receiver
T3-CC
……
CC receiver
T3-CC
1050mA1050mA
CC
1050mA
Page 11
T2
LED Color Temperature Controller
LED Color Temperature Controllerl
1. Operation Panel and Component Instruction:
Touch Color Circle
Sync Status
Indicator Light
T2 remote works with T3-CV, T3-CC receiver.
T2 can realize the signal sync on unlimited receivers within effective
distance, a very good solution for the LED project needs sync control
wirelessly.
Can RF remote the functions of color temperature dimming, quick
color temperature/brightness selection, DIY and delay off and so on.
User-friendly color wheel for color temperature adjustment, unique LED
state light for sync change indicated, user can simply know the LED
working state from distance by checking the remote control.
— 10 —
Speed+/Speed-
CT+/CTScene-mode Keys
(Press 3s to save)
CT Shortcut Keys
Delay Off Keys
★Buzzer on/off: Press “Delay Off key” for 3 seconds.
(Keep pressing to adjust
brightness continuously.)
BRT+/BRT-
Brightness
Shortcut Keys
On/Off
Page 12
2. The Learning ID Method of Remote:
Learning ID:
1. Turn on the receiver and remote.
2.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
the running light keeps on, then long press any key on the T2
remote (except “On/Off” key), the running light returns to flash (the
buzzer long beep, the indicator light flashes 3 times), activated
successful.
If you want to control multiple receivers synchronously, just follow
the above instructions for each receiver.
T2 remote works with T3-CV, T3-CC receiver.
LED Color Temperature Controller
Canceling ID:
1. Turn on the receiver and remote.
2. Press “ID learning button” on the T3-CC/T3-CV receiver more
than 8s, the buzzer beep twice, delete all the learned remote.
— 11 —
Page 13
3. System Diagram:
Unlimi ted receivers can be installe d within effective
distance, no wiring needed between the receivers, which
can be less or more in quantity according to your need
for the installation.
If you want to increase or decrease the receivers, just
activate or cancel the control ID on the remote control
will be fine, no any changes and effects on the other
receivers.
LED Color Temperature Controllerl
No quantity limit of the receivers.
— 12 —
Page 14
4. Wiring Diagram:
5~24Vdc 5~24Vdc 5~24Vdc
LED Color Temperature Controller
12~48Vdc12~48Vdc12~48Vdc
CV receiver
T3-CV
White/Warm White LED Strip
CV receiver
T3-CV
White/Warm White LED Strip
CVCV
CV CCCCCC
CV receiver
T3-CV
……
White/Warm White LED Strip
CC receiver
T3-CC
350mA
Round LED
Panel Light
CC receiver
T3-CC
700mA 1050mA
LED
Panel Light
CC receiver
T3-CC
LED
Panel Light
— 13 —
Page 15
T2M
LED Color Temperature Controller
LED Color Temperature Controller (8 Zones)
1. Operation Panel and Component Instruction:
Touch Color Circle
Sync Status
Indicator Light
T2M remote works with T3-CV, T3-CC receiver.
T2M can realize the signal sync on multiple receivers, zone controlled
arbitrarily (no more than 8 zones) within effective distance, a very good
solution for the LED project needs sync/zone control wirelessly.
Can RF remote the functions of color temperature touch adjustment,
brightness adjustment, and DIY scene modes. User-friendly color wheel
for color temperature adjustment, unique LED state light for sync change
indicated, user can simply know the LED working state from distance
by checking the remote control.
Speed+/Speed-
CT+/CT-
M1 M2
Scene-mode Keys
(Press for 3s to save the scene
mode in the 8 current zone control.)
Zone Control : Instruction
●
Select one of the zone: press any key of “1-8" on the remote.
●
Select zone control arbitrarily: press" + any number + ",
eg: take 456 as a zone, should press " 456 ".
●
All choose(8 zones): press " " twice.
●
When a zone is under inactive state, press
No. to
light up that zone.
the corresponding zone
★Buzzer on/off: Press “Zone Selection Key” for 3 seconds.
— 14 —
BRT+/BRT-
(Keep pressing to adjust
brightness continuously.)
Zone Selection Keys
On/Off
Page 16
LED Color Temperature Controller (8 Zones)
2. The Learning ID Method of Remote:
Learning ID:
A. Turn on the receiver and remote. A. Turn on the receiver and remote.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
B.
the running light keeps on, then long press any “1-8" “zone-selection
key” on the T2M remote, the running light returns to flash (the buzzer
long beep, the indicator light flashes 3 times), activated successful.
If installing multiple receivers in one zone, repeat the above steps,
choose the same zone key when ID learning.
T2M remote works with T3-CV, T3-CC receiver.
Canceling ID:
B. Press “ID learning button” on the T3-CC/T3-CV receiver more
than 8s, the buzzer beep twice, delete all the learned remote.
— 15 —
Page 17
3. System Diagram:
The receivers can be divided into 1~8 zones within effective
distance(1pc receiver per zone), no wiring needed between the
receivers.
zone 7
zone
8
6
zone
zone 1
zone
2
4
zone 5
zone
LED Color Temperature Controller (8 Zones)
If you don't need color temperature smooth mode by pressing
the , each zone can set up unlimited receivers and achieve
brightness, color temperature adjustment synchronously.
8
e
n
o
z
zone 3
7
e
n
o
z
6
e
n
o
z
n
e
o
z
1
z
o
n
e
2
z
o
n
e
3
z
o
n
e
4
z
o
e 5
n
Centralized Zone-division
— 16 —
Page 18
LED Color Temperature Controller (8 Zones)
4. Wiring Diagram:
zone1
zon
e
one4
z
3
zone
e2
zon
1
e
n
o
z
e4
n
o
z
zone3
2
one
z
one1
z
4
e
on
z
zone3
2
e
zon
Spacing Zone-division
2
z
one3
z
o
n
e
4
zo
ne1
z
one
2
5~24Vdc 5~24Vdc
CV receiver
T3-CV
T3-CV
CV CC
CV receiver
……
CC receiver
T3-CC
T3-CC
12~48Vdc12~48Vdc12~48Vdc
CC receiver
CC receiver
T3-CC
zone3
z
o
n
e
4
zon
e
1
z
o
n
e
2
zo
ne
3
zo
ne
4
zone1
White/Warm White LED Strip
White/Warm White LED Strip
350mA
Round LED
Panel Light
700mA 1050mA
LED
Panel Light
LED
Panel Light
— 17 —
Page 19
T3
LED RGB Controller
T3 remote works with T3-CV, T3-CC, T3-5A receiver.
T3 can realize the signal sync on unlimited receivers within effective
distance, a very good solution for the LED project needs sync control
wirelessly.
Can RF remote the functions of switch, pause, changing modes,
changing speed and the brightness and so on. Built-in 32 changing
modes, you can save the changing modes in the shortcut key as you
like, which not only can call at any time, but also can combine into a
program to play in loop.
1. Operation Panel and Component Instruction:
Touch Full-color Circle
Speed Keys
Mode Keys
Pause Key
★Buzzer on/off: Press “Pause key” for 3 seconds.
— 18 —
LED RGB Controller
Sync Status
Indicator Light
Brightness Keys
Scene-mode Keys
(Long press 3s to save)
Press"PLAY" key to play cycle
modes.(merely play the dynamic
effect, the static effect will be
skipped automatically)
On/Off
Page 20
2. The Learning ID Method of Remote:
T3-5A Learning ID:
A. Turn on the receiver and remote.
B. Press “on/off” on the T3-5A for 2s, there is a buzzer sound, keep
press, then press any key on the T3 (except “on/off” key) until the
indicator light flashes 3 times(the buzzer long beep at the same
time), learning ID successful, release all the keys.
T3-5A Cancelling ID:
A. Turn on the receiver and remote.
B. Press “on/off” on the T3-5A for 2s, there is a buzzer sound,
keep press, after 5s press any keys on the T3 (except “on/off”),
until the indicator light flashes 3 times, release all the keys.
T3 remote works with T3-CV, T3-CC, T3-5A receiver.
T3-CC/T3-CV Learning ID:
A. Turn on the receiver and remote.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
B.
the running light keeps on, then long press any keys (except “on/off”)
on the T3, the running light returns to flash (the buzzer long beep,
the green light flashes 3 times), activated successful.
T3-CC/T3-CV Cancelling ID:
A. Turn on the receiver and remote.
B. Press “ID learning button” on the T3-CC/T3-CV receiver more
than 8s, the buzzer beep twice, delete all the learned remote.
If you need to control multiple receivers synchronously, follow the
above steps for each receiver.
— 19 —
LED RGB Controller
Page 21
3. Tables of Changing Mode:
No.
1
Static red
Static green
2
Static blue
3
Static yellow
4
Static purple
5
Static cyan
6
Static white
7
RGB jumping
8
7 colors jumping
9
White strobe
10
7 colors strobe
11
Red fade out and fade in
12
Green fade out and fade in
13
Blue Fade out and fade in
14
Yellow fade out and fade in
15
Purple fade out and fade in
16
Comment: Speed/Brightness adjustable.
Mode
No.
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Cyan fade out and fade in
Mode
White fade out and fade in
RGB fade out and fade in
Red/Green color smooth
Red/Blue color smooth
Green/Blue color smooth
Red/Yellow color smooth
Green/Cyan color smooth
Blue/Purple color smooth
Green/Yellow color smooth
Blue/Cyan color smooth
Red/Purple color smooth
Blue/White color smooth
Yellow/Purple/Cyan color smooth
RGB color smooth
Full-color smooth
4. System Diagram:
Unlimited receivers can be installed within effective distance, no
wiring needed between the receivers, if you want to increase or
decrease the receivers, just activate or cancel the control ID will
be fine, no any changes and effects on other receivers.
— 20 —
LED RGB Controller
Page 22
5. Wiring Diagram:
12~24Vdc 12~24Vdc 12~24Vdc 5~24Vdc
LED RGB Controller
5~24Vdc 5~24Vdc 12~48Vdc 12~48Vdc 12~48Vdc
CV
CV receiver
RGB Strip
CV receiver
T3-CV
RGB Strip
T3- 5A
T3- 5A
RGB Strip
T3- 5A
RGB Strip
T3-CV
RGB Strip
CV CC
CV receiver
T3-CV
CC receiver
T3-CC
350mA
CC receiver
T3-CC
700mA 1050mA
RGB Strip
Round LED
Panel Light
LED
Panel Light
CC receiver
T3-CC
LED
Panel Light
— 21 —
Page 23
T3M
LED RGB Controller
T3M remote works with T3-CV, T3-CC, T3-5A receiver.
T3M can realize the signal sync on multiple receivers, zone controlled
arbitrarily (no more than 10 zones) within effective distance, a very good
solution for the LED project needs sync control wirelessly.
Can RF remote the functions of switch, pause, changing modes,
changing speed and the brightness and so on. Satisfied with your
requirement of sync control multiple zones, group control or control
separately, which it is easy to use.
— 22 —
LED RGB Controller (10 Zones)
1. Operation Panel and Component Instruction:
Touch Full-color Circle
Speed Key
Mode Key
32
5
6
4
87
9
Zone Selection Keys
10
M1
M2
Scene-mode Keys
Press for 3 seconds, can save
the scene mode
in the 10 current zone control
Zone Control : Instruction
●
Select one of the zone: press any key of “1-10" on the remote.
●
Select zone control arbitrarily: press" + any number + ",
eg: take 456 as a zone, should press " 456 ".
●
All choose(10 zones): press " " twice.
★Buzzer on/off: Press “Pause key” for 3 seconds.
Indicator Light
Brightness Key
Sync Status
Pause Key
On/Off
Page 24
2. The Learning ID Method of Remote:
T3-5A Learning ID:
A. Turn on the receiver and remote.
Press “on/off” on the T3-5A for 2s, there is a buzzer sound,
B.
keep press, then press any key of “1-10" zone on the T3M until the
indicator light of remote flashes 3 times (the buzzer long beep at
the same time), learning ID successful, release all the keys.
T3-5A Cancelling ID:
A. Turn on the receiver and remote.
Press “on/off” on the T3-5A for 2s, there is a buzzer sound, keep
B.
press, after 5s press any key of “1-10" zone on the T3M, until the
indicator light of remote flashes 3 times, release all the keys.
T3M remote works with T3-CV, T3-CC, T3-5A receiver.
LED RGB Controller (10 Zones)
T3-CC/T3-CV Learning ID:
A. Turn on the receiver and remote.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
B.
the running light keeps on, then long press any key of “1-10" zone
on the T3M remote, the running light returns to flash (the buzzer
long beep, the green light flashes 3 times), activated successful.
T3-CC/T3-CV Cancelling ID:
A. Turn on the receiver and remote.
Press “ID learning button” on the T3-CC/T3-CV receiver more
B.
than 8s, the buzzer beep twice, delete all the learned remote.
— 23 —
Page 25
3. Tables of Changing Mode:
No.
1
2
3
4
5
6
7
8
9
Mode
3 colors jumping
7 colors jumping
White strobe
7 colors strobe
RGB fade out and fade in
Red/Green color smooth
Red/Blue color smooth
Green/Blue color smooth
Red/Yellow color smooth
No.
10
Green/Cyan color smooth
11
Blue/Purple color smooth
12
Green/Yellow color smooth
13
Blue/Cyan color smooth
14
Red/Purple color smooth
15
Blue/White color smooth
16
Yellow/Purple/Cyan color smooth
17
RGB color smooth
18
Full-color smooth
Mode
LED RGB Controller (10 Zones)
4. System Diagram:
The receivers can be divided into 1~10 zones within effective
distance(1pc receiver per zone), no wiring needed between the
receivers.
0
1
one
z
ne 9
o
z
e 8
n
zo
e 7
n
zo
zon
e
1
zo
n
e 2
zo
n
e 3
z
o
n
e 4
Comment: Speed/Brightness adjustable.
— 24 —
zone 6
zon
e 5
Page 26
5. Wiring Diagram:
12~24Vdc 12~24Vdc 12~24Vdc 5~24Vdc
LED RGB Controller (10 Zones)
5~24Vdc 5~24Vdc 12~48Vdc 12~48Vdc 12~48Vdc
CV
CV receiver
RGB Strip
CV receiver
T3-CV
RGB Strip
T3- 5A
T3- 5A
RGB Strip
T3- 5A
RGB Strip
T3-CV
RGB Strip
CV CC
CV receiver
T3-CV
CC receiver
T3-CC
350mA
CC receiver
T3-CC
700mA 1050mA
RGB Strip
Round LED
Panel Light
LED
Panel Light
CC receiver
T3-CC
LED
Panel Light
— 25 —
Page 27
T3X
LED RGB Programmable Controller
LED RGB Programmable Controller
1. Operation Panel and Component Instruction:
Touch Full-color Circle
Sync Status
Indicator Light
T3X remote works with T3-CV, T3-CC, T3-5A receiver.
T3X can realize the signal sync on unlimited receivers within effective
distance, a very good solution for the LED project needs sync control
wirelessly.
Can RF remote the functions of switch, pause, mode, speed and LED
brightness. More proudly, the T3X has the brand-new programmable
function, only 10 seconds to DIY a new change effect.
Programming has never been so easy.
Speed Keys
Mode Keys
Scene-mode Keys
(Press 3 seconds to save)
(Press"PLAY" to play cycle modes.
merely play the dynamic effect,
the static effect will be skipped)
DIY Key for Color Selection
DIY Key for Color Selection
Long press for 2 seconds to enter DIY programming function.
●
1. Select any color on , the controller will save immediately.
2. Press to enter next color. (can save 1-10 colors)
3. After color selection, press to switch jumping/smooth/flickering changing effect.
4. Adjust the brightness and the speed by pressing the “SPEED” and “ BRT”.
5. Save the new program into the “Scene-mode keys”.
●
Additional Functions:
▲
Long press ”DIY key for color selection” to clear the current color.
▲
Press “MODE” key under DIY function, can display the standard color for black,
red, green, blue, yellow, purple, cyan and white. Among them, black can be used
for editing fade in dimming effect, etc.
★Buzzer on/off: Press “Scene-mode Key” for 3 seconds.
— 26 —
Brightness Keys
On/Off
Switch Key for
Changing Modes
Page 28
2. The Learning ID Method of Remote:
T3-5A Learning ID:
A. Turn on the receiver and remote.
Press “On/Off” on the T3-5A for 2s, there is a buzzer sound,
B.
keep press, then press any key on the T3X (except “On/Off” key)
until the indicator light flashes 3 times(the buzzer long beep at
the same time), learning ID successful, release all the keys.
T3-5A Cancelling ID:
A. Turn on the receiver and remote.
Press “On/Off” on the T3-5A for 2s, there is a buzzer sound,
B.
keep press, after 5s press any key on the T3X (except “On/Off”),
until the indicator light flashes 3 times, release all the keys.
T3X remote works with T3-CV, T3-CC, T3-5A receiver.
LED RGB Programmable Controller
T3-CC/T3-CV Learning ID:
A. Turn on the receiver and remote.
Short press "ID learning button" on the T3-CC/T3-CV receiver,
B.
the running light keeps on, then long press any key (except “On/Off”)
on the T3X remote, the running light returns to flash (the buzzer long
beep, the green light flashes 3 times), activated successful.
T3-CC/T3-CV Cancelling ID:
A. Turn on the receiver and remote.
B. Press “ID learning button” on the T3-CC/T3-CV receiver more
than 8s, the buzzer beep twice, delete all the learned remote.
If you need to control multiple receivers synchronously, follow the
above steps for each receiver.
— 27 —
Page 29
3. Tables of Changing Mode:
No.
1
Static red
2
Static green
3
Static blue
4
Static yellow
5
Static purple
6
Static cyan
7
Static white
8
RGB jumping
9
7 colors jumping
10
White strobe
11
7 colors strobe
12
Red fade out and fade in
13
Green fade out and fade in
14
Blue fade out and fade in
15
Yellow fade out and fade in
16
Purple fade out and fade in
Comment: Speed/Brightness adjustable.
Mode
No.
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Cyan fade out and fade in
Mode
White fade out and fade in
RGB fade out and fade in
Red/Green color smooth
Red/Blue color smooth
Green/Blue color smooth
Red/Yellow color smooth
Green/Cyan color smooth
Blue/Purple color smooth
Green/Yellow color smooth
Blue/Cyan color smooth
Red/Purple color smooth
Blue/White color smooth
Yellow/Purple/Cyan color smooth
RGB color smooth
Full-color smooth
LED RGB Programmable Controller
4. System Diagram:
Unlimited receivers can be installed within effective distance, no
wiring needed between the receivers, if you want to increase or
decrease the receivers, just activate or cancel the control ID will
be fine, no any changes and effects on other receivers.
— 28 —
Page 30
5. Wiring Diagram:
12~24Vdc 12~24Vdc 12~24Vdc 5~24Vdc
LED RGB Programmable Controller
5~24Vdc 5~24Vdc 12~48Vdc 12~48Vdc 12~48Vdc
CV
CV receiver
RGB Strip
CV receiver
T3-CV
RGB Strip
T3- 5A
T3- 5A
RGB Strip
T3- 5A
RGB Strip
T3-CV
RGB Strip
CV CC
CV receiver
T3-CV
CC receiver
T3-CC
350mA
CC receiver
T3-CC
700mA 1050mA
RGB Strip
Round LED
Panel Light
LED
Panel Light
CC receiver
T3-CC
LED
Panel Light
— 29 —
Page 31
Ⅰ. Attention:
A. The product shall be installed and serviced by the qualified person.
B. This product is non-waterproof. Please avoid the sun and rain.
When installed outdoors please ensure it is mounted in a water
proof enclosure.
C. Good heat dissipation will prolong the working life of the controller.
Please ensure good ventilation.
D. Please check if the output voltage of the LED power supply used
comply with the working voltage of the product.
E. Please ensure that adequate sized cable is used from the controller
to the LED lights to carry the current. Please also ensure that the
cable is secured tightly in the connector.
F. Ensure all wire connections and polarities are correct before applying
power to avoid any damages to the LED lights.
G. If a fault occurs, please return the product to your supplier. Do not
attempt to fix this product by yourself.
Ⅱ. Warranty Agreement:
A. We provide lifelong technical assistance with this product:
A 5-year warranty is given from the date of purchase. The warranty
is for free repair or replacement if cover manufacturing faults only.
For faults beyond the 5-year warranty, we reserve the right to charge
for time and parts.
B. Warranty exclusions below:
Any man-made damages caused from improper operation, or
connecting to excess voltage and overloading.
The product appears to have excessive physical damage.
Damage due to natural disasters and force majeure.
Warranty label, fragile label and unique barcode label have been
damaged.
The product has been replaced by a brand new product.
C. Repair or replacement as provided under this warranty is the
exclusive remedy to the customer. We shall not be liable for any
incidental or consequential damages for breach of any stipulation
in this warranty.
D. Any amendment or adjustment to this warranty must be approved
in writing by our company only.
★ This manual only applies to this model. We reserve the right to
make changes without prior notice.
— 30 —
After Service
Page 32
Reset and Edit the Frequency Point
Reset and Edit the Frequency Point
A. Reset Function:
Feature: Reset function is available when remote operates abnormally.
Operation:
B. Check and Edit the Frequency Point on the Remote:
Feature:
Attn: After reset or revised the frequency points in the remote, receivers only can be used after relearn the ID.
Check the Frequency Point on the Remote:
Turn on the remote, long press the key for 5 seconds until the red light ( for T1) flashes 3 times, and then the green light
(white light for T1 ) flashes, the numbers of the flash will be the frequency point of the remote. you can only edit the frequency point after 3 seconds.
Edit the Frequency Point on the Remote:
Method 1:
Method 2:
Long press the 2 keys on the positions of simultaneously, release after 3 seconds, the remote will be auto off,
means reset completed. and then could restart the remote.
a.
Revising the frequency point to eliminate the external disturbance. 12 revisable frequency points for user.
A
b. Multiple remotes sync-control becomes available when they use the same frequency point.
Remotes of the same frequency point, only one remote could be used to execute the learning ID process, the rest needs to be off.
white light
In frequency changing state,
2
3
Short press any key on the positions of , the frequency point will be “1-9” correspondingly, the light will flash in the same
numbers. Then press any key or touch the color circle to exit the frequency edit state.
1
4
5
6
8
9
7
Long press “on/off” key over 5 seconds, the green light (white light for T1) flashes, the flash times plus 1 means the frequency
point accumulate 1. In short, long press the “on/off” key over 5 seconds each time, the frequency point will accumulate 1, which will
again become value 1 when added to 12, and that cycle repeats.
— 31 —
Update Time:2016.01.21_A5
1
4
7
3
2
6
5
9
8
A
Page 33
T Series LED Remote Controller
Applied Range
Architectural ornament: business area, airport, subway station.
Interior decoration: hotel, shopping mall, square, restaurant,
pub, home furnishing, etc.
Signboard, billboard.
Anywhere else, where uses LED for dimming, color temperature
and full color adjustment.
Parameters
Charing Voltage: 5Vdc (Built-in Lithium Battery)
Working Current: ≤30mA
Working Frequency: 2.4GHz
Remote Distance: 30m
With USB Charging Por t
warranty
5 years
Loading...