Page 1
LumeLEX 2030/2031 SERIES INSTALLATION INSTRUCTIONS
Important
Warning
Product
Overview
Purpose of
This Sheet
THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
This product must be installed in accordance with National Electrical Codes and all other
local codes by a person familiar with the construction and operation of the product and
the hazards involved.
To prevent electrical shock, turn off the power during installation or maintenance.
To reduce the risk of fire, keep away from combustible materials.
The LumeLEX 2030/2031 Series is a clean,
elegant stem mounted LED spotlight with a
discreetly hidden driver, making it appear no
different than a traditional halogen source.
With independent ratings of 97CRI, the
LumeLEX 2030/2031 series, based on the
latest in Remote Corrected Cold Phosphor
Technology by Xicato, has the highest Color
Rendering Index of any LED on the market
today, producing the most consistent, highest
quality white light and maintaining extremely
tight color control (within 2 MacAdam ellipses,
vs. the NEMA standard of 7). The LumeLEX
2030/2031 series also features a snap-out
cross baffle and accessory cartridge which
accepts up to two optical accessories, size
‘AAA’.
See the fixture label for voltage and wattage
input.
Please consult our Product Catalog or web
site for available accessories.
We recommend that you first install the
reflector and any accessories before
installing the fixture.
The purpose of this sheet is to provide step-by-step instructions to help you:
Install the fixture with any of the following: -00E fitting on an LSI track, -BUSE fitting on an LSI
Busway, -5AE canopy.
Install accessory filters and reflectors
Aim the self-locking and wrench-locking fixture
Clean the optical surfaces and reflector
LumeLEX 2030 Series Spotlight
www.LightingServicesInc.com Page 1 of 6 IS-0139_A
Page 2
Changing
or
Installing
the
Reflector
Before Changing Reflector: To maintain the
fixture’s current orientation, change the reflector
with the fixture in its location. If the orientation
does change, refer to the “Aiming the Fixture”
section of this sheet. Refer to our Product Catalog
or web site for reflector options.
Follow steps 1, 2, 4, and 5 if you are installing
the reflector for the first time.
STEP ACTION
1 Turn off all power to the fixture,
including the fixture switch on the
fitting, and let the LED cool.
WARNING: LED and fixture may be
hot.
2 Remove the cylinder housing by
grasping the fitting stem in one hand
and the cylinder housing in the other.
Pull in opposite directions while
rocking the housing gently side to
side. (Fig. 1).
3 Remove the reflector by turning it
counter-clockwise, then pulling it out
of the fixture. (Fig. 2).
4 Insert the new reflector by lining up
the three tabs with the notches in the
LED Adapter Ring, and rotating
clockwise until it is secured in
place.(Fig 3)
Figure 1. Cylinder housing loosened and
notches aligned (arrow). Pull off to expose
lamp, or push onto stem to close and secure
housing.
Figure 2. Rotate reflector counter-clockwise to
remove it.
5 Close the fixture front by replacing the
cylinder housing. Align the stem
notch to the cylinder housing notch
and push the cylinder housing onto
the stem notch until it clicks into place
and is secured. (Fig. 1).
6 Restore power.
WARNING: Do not look directly at
the lit LED.
www.LightingServicesInc.com Page 2 of 6 IS-0139_A
Figure 3. The three notches in the LED Adapter
Ring. Align the reflector tabs with these
notches and rotate clockwise to secure in it.
Page 3
r
r
w
Installing
the Fixture
with the
-00E Fitting
on an LSI
Track or a
-BUSE
fitting on
an LSI
Busway
FOR USE WITH LSI 3, 4, 5, 6, 8, AND 9 SERIES TRACK
AND LSI 20 SERIES BUSWAY SYSTEMS ONLY.
INSTALLATION INSTRUCTIONS: The track or busway
must already be installed according to code requirements.
When installing or using this track or busway system, basic
safety precautions should always be followed, including the
following:
Read all instructions.
Do not install any part of a track or busway system less
than 5 feet above the floor (8 feet for 277V).
Do not install any fixture closer than 6 inches from any
curtain or similar combustible material.
STEP ACTION
1 Flip the fitting switch off and open the fitting handle
(Fig. 4).
2
Are you using a one-circuit or two-circuit system?
If one-circuit, make sure the brass contacts that
protrude from the side of the fitting face the copper
busbars inside the track or busway.
If two-circuit, inserting the fitting in one direction
connects to circuit one. Removing and reversing
the direction of the fitting connects to circuit two.
3 Insert the fitting straight up into the track or busway
until fully seated (Fig. 5).
Figure 4. Fitting with switch OFF
and handle OPEN.
Figure 5. Inserted fitting
Installing
the Fixture
with a 5AE
Canopy
4
Close the handle and flip the fitting switch on (Fig 6).
WARNING: Do not look directly at lit LED.
5 To remove the fitting, hold the fixture in place, flip
the fitting switch off, open the handle, and pull the
fitting straight off the track or busway.
Before Installing: Consult the code requirements for fixture
mounting. Mount the fixture to a ceiling constructed of noncombustible material, away from any flammable materials.
STEP ACTION
1 Turn off all power to the fixture mount.
2 Unscrew the 2 supplied canopy mounting screws,
and remove the crossbar from the canopy (Fig. 7).
3 Attach the canopy crossbar (Fig. 8) to a ceiling
junction box with 2 screws (supplied by others).
4 Fasten the power wires (Fig. 8) from the junction
box to the LED driver. Secure the driver inside the
junction box with tape supplied, taking care not to
pinch or damage any wires. (Fig. 8)
Note: Connect green to ground, black to the
circuit line, and white to neutral.
5 Attach the canopy to the ceiling with the 2 supplied
canopy mounting screws.
Figure 6. Switch ON, fitting handle
closed
Figure 7. Fixture mounted on the
5AE Canopy
Crossba
Transformer/
Drive
Ground
Figure 8. Junction Box, crossbar,
ground screw (green) and a
transformer/driver secured.
Scre
www.LightingServicesInc.com Page 3 of 6 IS-0139_A
Page 4
Installing
Accessory
Filters and
Reflectors
Before Installing:
removable accessory cartridge that holds size-AAA LSI filters
and accessories, as well as other reflectors. The LumeLEX
2030/2031 package includes accessory cartridges and a
reflector. Consult our Product Catalog or web site for
accessory recommendations.
STEP ACTION
The LumeLEX 2030/2031 has a
1 Turn off all power to the fixture, including
the fixture switch on the fitting, and let the
lamp cool.
WARNING: LED and fixture may be hot.
2 Remove the cross-baffle cartridge
assembly by pulling it out of the cylinder
housing (Fig. 9) .
3 Insert any double combination of size-AAA
filters and accessories into the Accessory
Cartridge Clips (Fig. 10)(LX-2030) or
(Fig 11)(LX-2031).
Alternatively, the Accessory Cartridge will
accept a single or combination of size-AAA
gels, which are secured with the included
Backer Ring (Fig. 10). Insert the gel into
the Accessory Cartridge, taking care to
orient non-symmetrical gels properly (refer
to instruction sheet for LX2031 for specific
gel orientation) and having the dull side
facing in towards the LED. Secure the gels
by inserting the backer ring on top and
seating it firmly in the cartridge.
4 Reinsert Accessory Cartridge into the
cylinder housing by pushing in the
Retension Tabs on the sides of the
cartridge (Fig. 10).
Ensure that the cartridge is pushed all the
way in, with the Cross-Baffle being flush or
below the front edge of the housing (Fig.9).
For LX-2031, ensure that the top of the
Kicker Reflector Bracket is aligned with the
slot in the LX-2031 front. Push until the top
of the Kicker Reflector Bracket is bottomed
out in the slot. (Fig 11)
Figure 9. Remove Cross-Baffle cartridge
assembly by pulling it out of the cylinder
housing. Cross-Baffle should be flush
or below front edge of housing when
installed.
Accessory Clips
Backer Ring
Retension Tabs
Figure 10(LX-2030). Accessory Clips,
Retension Tabs, Backer Ring.
Accessory
Clips
Slot
Top of
Bracket
5 Restore power.
WARNING: Do not look directly at the lit
www.LightingServicesInc.com Page 4 of 6 IS-0139_A
LED.
Kicker
Reflector
Bracket
Figure 11(LX-2031). Accessory Clips,
Tabs, Kicker Reflector Bracket
Page 5
e
Aiming the
SelfLocking
and
WrenchLocking
Fixtures
Before Aiming: For self-locking, you do not need
an external locking device to set the horizontal and
vertical focus. For wrench locking, use the
supplied Allen key (3/32 inches) to set and lock the
horizontal and vertical focus.
STEP ACTION
1 Turn off all power to the fixture,
including the fixture switch on the
fitting, and let the lamp cool.
WARNING: LED and fixture may be
hot.
2 Do you want to aim the fixture
horizontally or vertically?
For horizontal aiming, hold the
lamp housing and turn it left or
right until you achieve your desired
orientation (Fig. 12).
For vertical aiming, hold the lamp
housing and angle it up and down
until you achieve your desired
orientation (Fig. 13).
For wrench locking: After aiming,
insert the Allen key into the
horizontal or vertical focus lock
(Fig. 14), and turn it clockwise to
tighten.
Note: Allen key is supplied for track
and busway fixtures. It is stored in
fitting handle (Fig. 15).
Figure 12. Turn fixture left or right to set the
horizontal focus.
Figure 13. Angle fixture up or down to set the
vertical focus.
3 Restore power.
WARNING: Do not look directly at
the lit LED.
Pull to remove
Push to stor
Figure 14. Horizontal focus lock (L). Vertical
focus lock (R).
Figure 15. Allen key storage in fitting.
Push in to secure the key.
www.LightingServicesInc.com Page 5 of 6 IS-0139_A
Page 6
Important
Cleaning
the
Reflector
CLEANING INSTRUCTIONS for
LumeLEX 2000 REFLECTORS
FOLLOW THESE INSTRUCTIONS SO TO PREVENT DAMAGE TO
YOUR REFLECTOR. NOT CLEANING THE REFLECTOR
CORRECTLY CAN REDUCE THE EFFICIENCY OF THE OPTICAL
SURFACE. DO NOT TOUCH THE SURFACE OF THE
REFLECTOR WITH YOUR BARE SKIN, AS HUMAN SKIN OIL
WILL DEGRADE THE OPTICAL SURFACE.
INSTRUCTIONS: Follow instructions from the specific
fixture and reflector for removal and assembly of the
reflector to that fixture. Wear blue nitrile gloves during
this process to ensure not to touch the optical surface of
the reflector with your bare skin.
MATERIALS REQUIRED:
● De-ionized water
● Blue Nitrile Gloves
● Dish soap (such as Dawn
● Can of clean compressed air OR ● Air Bulb (aka suction bulb)
● Lens Tissue (such as Kemwipes
®
) OR ● Isopropyl Alcohol
®
) OR ● Terry Cloth
STEP ACTION
1
2 Using either a can of clean compressed
3 Apply a generous amount of either
4 While wearing nitrile gloves, gently
5 Allow optic to dry prior to reinstalling
Remove the reflector from the fixture
air or a bulb, blow clean air across to
remove any surface dust or debris.
De-ionized water combined with a small
amount of dish soap, or Isopropyl
Alcohol, to a lens tissue or terry cloth.
clean the inside of the reflector with the
wet lens tissue or terry cloth.
onto the fixture.
www.LightingServicesInc.com Page 6 of 6 IS-0139_A
Loading...