LSI LSISAS3442E-R Quick Installation Manual

®
80-00148-01
Thank you for purchasing the LSI Logic LSISAS3442E-R PCI Express to 3.0Gbit/s Serial Attached SCSI (SAS) Host Bus Adapter (HBA). Please take a few minutes to read this Quick Installation Guide before you install the LSISAS3442E-R.
If you need more information about any topic covered in this guide, please refer to the other documents on the accompanying LSI Device Drivers & Utilities CD.
CONTENTS OF THE LSI DEVICE DRIVERS & UTILITIES CD
The LSI HBA CD contains utility programs, device drivers for various operating systems, and the following documentation:
PCI Express to 3.0Gbit/s Serial Attached SCSI (SAS) Host
Adapters User’s Guide
LSI Fusion-MPT Device Management User’s Guide
LSI HBA technical product briefs
QUICK HOST ADAPTER INSTALLATION
To install the LSISAS3442E-R host adapter, follow these steps:
Step 1 Unpack the host adapter and inspect it for damage.
Unpack the host adapter in a static-free environment. Remove the host adapter from the antistatic bag and inspect it for damage. If it appears to be damaged, or if any component is missing, contact LSI or your reseller support representative.
Make a backup of your data before changing your system configuration.
Step 2 Prepare the computer.
Turn off the computer and remove the power cord from the back of the power supply. Remove the cover from the chassis.
Be certain to disconnect the computer from the power supply and from any networks before installing the controller card.
Step 3 Insert the LSISAS3442E-R in an available PCI
Express slot.
Locate an empty PCI Express slot. Remove the blank bracket panelonthe back of the computer that is aligned with the PCI Express slot you have selected. Save the bracket screw when present.
Align the host adapter with a PCI Express slot. Press down gently but firmly to properly seat the host adapter in the slot. The following figure illustrates how to insert the host adapter in a PCI Express slot.
Step 4 Secure the bracket to the system chassis.
Install the bracket screw, when present, or engage the system’s retention mechanism to secure the host adapter to the system’s chassis.
Note: The HBA shape, size, and locations of components may
vary from this illustration.
32-bit Slots
64-bit Slot
(3.3 V Only)
(3.3 V Only)
Edge of
Host Board
Bracket
Press Here
HDD
Connector
Serial Signal Cables
HBA to HDD
4-Lane Internal HBA Connector
4-Lane
External
PCB
Receptacle
and Cable
with
Jackscrews
Screw
SFF-8484
SFF-8470
Breakout Cable
Press Here
PCI Express X8 Slot
LSISAS3442E-R PCI Express to 3.0 Gbit/s Serial Attached SCSI (SAS) Host Bus Adapter
Quick Installation Guide
DB11-000079-00, Version 1.0, July 2006 Find a list of LSI Logic Corporation’s U.S. distributors, international distributors,
sales offices, and design resource centers on the LSI Logic web site at:
http://www.lsilogic.com/contacts/index.html
®
LSI Logic, the LSI Logic logo design, and Fusion-MPT are trademarks or registered trademarks of LSI Logic Corporation. All other brand and product names may be trademarks of their respective companies.
Copyright © 2006 by LSI Logic Corporation. All rights reserved. LSI Logic Corporation reserves the right to make changes to any products and
services herein at any time without notice. LSI Logic does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by LSI Logic; nor does the purchase, lease, or use of a product or service from LSI Logic convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Logic or of third parties.
Step 5 Connect the serial cable(s) between the host adapter
and the serial hard disk drive(s) (HDD).
The LSISAS3442E-R has two SAS signal connectors (one external and one internal), each connecting to four 3 Gbit/s SAS ports. The HBA needs to be connected to SAS storage devices using the appropriate cable. A SAS External Cable with a standard SAS External Plug connector (SFF-8470) is required to connect to external devices.
For connection to internal drives or backplanes, an internal cable with a standard SAS Internal Wide Port connector (SFF-8484) on the controller side of the cable is required. The other end of the cable may fan out into four cables with either SATA-style signal connectors or SAS device connectors at the end for direct connection to disk drives (and some backplanes) or single SAS Internal Wide Port connector for backplane attachment. The preceding figure illustrates the connector locations on the LSISAS3442E-R HBA and use of controller­based, fan-out cable to connect to drives requiring a SATA-style signal connector.
Step 6 Replace the cover, the power cord(s) and power-up
the system.
Replace the system’s cover, reconnect the power cord(s) and any network cables. Turn power on to the system.
The LSISAS3442E-R host adapter hardware installation is complete, and you are ready to install the operating system drivers.
WINDOWS DRIVER INSTALLATION
To load the SYMMPI.SYS miniport driver during a new Windows 2000 or Windows XP system installation or to load the LSI_SAS.SYS driver during a new Windows 2003 installation, you can boot directly from the Microsoft installation CD-ROM. The Windows drivers are not interchangeable; however, the instructions are very similar.
To install a new Windows operating system and its appropriate device driver, follow these steps:
Step 1 Using another computer, copy the appropriate driver files
supplied on the LSI Device Drivers and Utilities CD onto a diskette. This will be needed in Step 6.
To create the driver diskette, open the driver folder on the CD, then open the folder for the version of Windows to be installed on the new system. Next, select all folders and files within the directory and copy to the root director of a clean floppy diskette.
Step 2 Boot the computer from the Microsoft Windows CD-ROM. Step 3 Shortly after Windows Setup begins, press F6 when the
words Setup is inspecting your computer's hardware configuration appear, or when prompted to press F6
if you need to install a third-party SCSI or RAID driver.
Important: You must press F6 for the new driver to be recognized.
Otherwise, the system does not recognize the devices controlled by the driver during the Windows setup.
Step 4 Follow the instructions until a screen displaying the
words Setup could not determine the type of one or more mass storage device… appears.
Step 5 Press S to Specify Additional Devices.
Step 6 Followthe prompts and insert the Windows driver diskette
when prompted to insert the hardware support disk. Select the driver version appropriate for your system.
Step 7 Follow the Microsoft Windows installation procedure to
complete the installation. Microsoft provides documentation with its installation CD-ROM.
Note: Refer to the Fusion-MPT™ Device Management User’s
Guide for detailed configuration and installation
instructions for all firmware and drivers.
LINUX DRIVER INSTALLATION
Consult the Linux ReadMe.txt file on the LSI Device Drivers & Utilities CD. LSI provides Open Source drivers that may be implemented in the following ways:
Step 1 Adding precompiled binaries to an existing installation
using driver update disks or RPMs for selected distributions.
Step 2 Adding or updating the Fusion-MPT™ source in the
Linux kernel for any distribution.
Technical Support
For assistance installing, configuring, or running the LSISAS3442E-R, contact LSI Technical Support:
Phone Support
1-800-633-4545 (North America) +44 1344 413 441 (Europe)
Web Site
http://www.lsilogic.com/support/
Loading...