LSI LSIiBBU09 Quick Installation Manual

MegaRAID® LSIiBBU09 Intelligent Battery

49760-00B

Backup Unit

Quick Installation Guide

49760-00, Rev. B

August 2012

MegaRAID LSIiBBU09 Intelligent Battery Backup Unit Quick Installation Guide
June 2012

Revision History

Version and Date Description of Changes

49760-00 Rev. B, August 2012 Updated the list of RAID controllers that support the LSIiBBU09 unit.

49760-00 Rev. A, January 2011 Initial release of the document.

LSI, the LSI Design logo, and MegaRAID are registered trademarks of LSI Corporation or its subsidiaries. All other br and and product names may be trademarks of their respective companies.

LSI Corporation reserves the right to make changes to the product(s) or information disclosed herein at any time without notice. LSI Corporation does not assume any responsibility or liability arising out of
the application or use of any product or service described herein, except as expressly agreed to in writing by LSI Corporation; nor does the purchase, lease, or use of a product or service from LSI Corporation
convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Corporation or of third parties. LSI products are not intended for use in life-support
appliances, devices, or systems. Use of any LSI product in such applications without written consent of the appropriate LSI officer is prohibited.

Corporate Headquarters Website

Milpitas, CA www.lsi.com
800-372-2447

Document Number: 49760-00, Rev. B
Copyright © 2012 LSI Corporati on
All Rights Reserved

MegaRAID LSIiBBU09 Intelligent Battery Backup Unit Quick Installation Guide
August 2012

MegaRAID® LSIiBBU09 Intelligent Battery Backup Unit

Thank you for purchasing the LSI® MegaRAID® LSIiBBU09 intelligent battery backup unit (iBBU). Before you install and
connect the LSIiBBU09 unit, please take a few minutes to read this quick installation guide. This guide explains how to
connect the LSIiBBU09 unit to your MegaRAID SAS RAID controller.

If you need more information about any topic covered in this guide, refer to the related documents on your MegaRAID
Universal Software Suite CD.

Product Overview

The LSI MegaRAID LSIiBBU09 product is an iBBU based on Lithium ion (LiON) battery cell technology. The LSIiBBU09
unit protects the integrity of the cached data on a MegaRAID RAID controller for up to 48 hours (depending on the
derated retention time selected) in case of a complete AC power failure or a brief power outage. You can connect the
LSIiBBU09 unit either directly or remotely to your RAID controller, depending on which RAID controller you have.

LSI provides a family of MegaRAID iBBUs for use with its high-performance MegaRAID RAID controllers. The LSI
MegaRAID iBBUs provide an inexpensive alternative to using an uninterruptible power supply (UPS) and a second
level of fault tolerance when used with a UPS.

Product Overview

Direct Connection

Direct Connection

The LSIiBBU09 unit connects directly to the following MegaRAID SAS RAID controllers:

 MegaRAID SAS 9266-4i RAID controller
 MegaRAID SAS 9266-8i RAID controller

See Attaching a LSIiBBU09 Unit Directly to a MegaRAID SAS 9266 RAID Controller for instructions on how to attach the
LSIiBBU09 unit directly to these controllers.

Remote Connection

The LSIiBBU09 unit connects remotely to the following MegaRAID SAS RAID controllers:

 MegaRAID SAS 9265-8i RAID controller
 MegaRAID SAS 9266-4i RAID controller
 MegaRAID SAS 9266-8i RAID controller
 MegaRAID SAS 9285-8e RAID controller

The LSIiBBU09 unit connects remotely by cable to the MegaRAID SAS 9266-4i RAID controller and the MegaRAID SAS
9266-8i RAID controller.

The LSIiBBU09 unit connects remotely to a TMM02® transportable memory module that is attached to the MegaRAID
SAS 9265-8i RAID controller and the MegaRAID SAS 9285-8e RAID controller. You have two ways to connect the
remote LSIiBBU09 unit by cable to a TMM02 transportable memory module on these two controllers:

 Connect the LSIiBBU09 unit by cable to the TMM02 module on the RAID controller and then mount the LSIiBBU09

unit on the system chassis (see Connecting a Remote LSIiBBU09 Unit on the System Chassis to a TMM02 Module

on a RAID Controller on page 11 for the instructions).

LSI Corporation

- 3 -

MegaRAID LSIiBBU09 Intelligent Battery Backup Unit Quick Installation Guide

LSI CORP.© 2010 ALL RIGHTS RESERVED

Pb e1

ASSEMBLED

IN CHINA

RoHS

AsRPCB

E248037

94V0

Li Ion

Model: BAT1S1P-A

BBU P/N: L4-25407-00

BBU S/N: SAYWWSSSSSss

Contains:
Sony US454261A8TCell
Rechargeable Li-Polymer
Battery Pack
Rating:

3.7V; 1.59 Ah; 5.9Wh
Finished in China

WARNING: The battery used in this
device may present a risk of fire or
chemical burn if mistreated. DO NOT
disassemble, heat above 60C, crush or
puncture, short circuit external contacts,
or dispose of in fire or water.

MH29577

Li-ion

!

L3-25407-00A

Top View

Bottom View

85083-00

1

2

August 2012

 Connect the LSIiBBU09 unit on a remote mounting board by cable to the TMM02 module on the RAID controller

(see Connecting a LSIiBBU09 Unit on a Remote Mounting Board to a TMM02 Module on a RAID Controller on
page 13 for the instructions).

WARNING The battery used in this device might present a fire or chemical burn hazard if mistreated. Do
not disassemble, heat above 100 °C (212 °F) or incinerate. Dispose of used battery correctly. Keep it away
from children.

Top View and Bottom View of the LSIiBBU09 Unit

The following figure shows the top view and the bottom view of the LSIiBBU09 unit. The top view is the side that
you can see after you install the LSIiBBU09 unit on the system chassis or when the unit is installed on a remote
mounting board.

Figure 1 Top View and Bottom View of the LSIiBBU09 Unit

Top View and Bottom View of the LSIiBBU09 Unit

Remote Connection

1. Board-to-Board Connector

2. Remote Cable Connector

NOTE Record your controller serial number in a safe location in case you need to contact LSI.

LSI Corporation

- 4 -

MegaRAID LSIiBBU09 Intelligent Battery Backup Unit Quick Installation Guide
August 2012

Attaching a LSIiBBU09 Unit Directly to a MegaRAID SAS 9266 RAID Controller

Removing the RAID Controller from the Computer

Attaching a LSIiBBU09 Unit Directly to a MegaRAID SAS 9266 RAID Controller

This section describes how to connect the MegaRAID LSIiBBU09 unit directly to a MegaRAID SAS 9266-4i RAID
controller or a MegaRAID SAS 9266-8i RAID controller.

WARNING The battery used in this device might present a fire or chemical burn hazard if mistreated. Do
not disassemble, heat above 100 °C (212 °F) or incinerate. Dispose of used battery correctly. Keep it away
from children.

Perform the following tasks described in this section to attach the LSIiBBU09 unit directly to the MegaRAID SAS 9266
RAID controller.

1. Remove the RAID controller from the computer. See Removing the RAID Controller from the Computer.

2. Attach the LSIiBBU09 unit directly to the RAID controller. See Attaching the LSIiBBU09 Unit to the RAID Controller.

3. Reinstall the RAID controller on the motherboard. See Reinstalling the RAID Controller on the Motherboard on
page 6.

CAUTION Electrostatic discharge (ESD) can damage the LSIiBBU09 unit and the RAID controller. Make
sure that you install the LSIiBBU09 unit at an ESD-safe workstation that meets the EIA-625 standard. When
you install the LSIiBBU09 unit, follow the ESD-recommended practices in the latest revision of the
IPC-A-610 standard.

Removing the RAID Controller from the Computer

Follow these steps to remove the RAID controller from the computer.

1. Turn off the power, and unplug the power cords.

2. Ground yourself, and make sure that the system is grounded.

3. Remove the cover from the computer, according to the instructions in the system user’s manual, to permit access
to the controller.

4. Unplug all cables from the controller, remove the screw that attaches the bracket to the computer chassis, and
carefully remove the controller from the slot.

5. Place the controller on a flat, clean, static-free surface, and continue with the next procedure.

Attaching the LSIiBBU09 Unit to the RAID Controller

Follow these steps to attach the LSIiBBU09 unit directly to the front of the RAID controller.

WAR NING There is danger of an explosion if the battery is incorrectly replaced. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

1. Ground yourself, and make sure that the system is grounded.

2. Remove the LSIiBBU09 unit from the package.

3. Place the LSIiBBU09 unit front-side-up on a flat, clean, static-free surface.

4. Place the RAID controller front-side-up on a flat, clean, static-free surface.

5. Hold the LSIiBBU09 unit so that the top of the battery is facing upward, and the J1 connector lines up with the
J1A3 BBU connector on the RAID controller, as the following figure shows.

LSI Corporation

- 5 -

MegaRAID LSIiBBU09 Intelligent Battery Backup Unit Quick Installation Guide

3_00896-00

J1A3

LSIiBBU09

August 2012

Figure 2 Attaching the LSIiBBU09 Unit to the RAID Controller

6. Carefully press the LSIiBBU09 unit onto the RAID controller so that the two connectors are firmly joined.

7. Secure the LSIiBBU09 unit to the RAID controller with the screws and the standoffs in the three screw holes.

The standoffs are threaded at both ends, and a screw goes into each end. The screw threads from the back of the
controller board into the board-to-board standoffs on the bottom of the LSIiBBU09 unit.

Center the screwdriver carefully to avoid stripping the screw heads. Do not over-tighten the screws.

Attaching a LSIiBBU09 Unit Directly to a MegaRAID SAS 9266 RAID Controller

Reinstalling the RAID Controller on the Motherboard

Reinstalling the RAID Controller on the Motherboard

Follow these steps to reinstall the RAID controller on a motherboard.

1. Make sure that the power to the chassis is still turned off, the power cords are unplugged, and the chassis is
grounded and has no AC power.

2. Install the RAID controller in a PCI Express slot on the motherboard, as the following figure shows.

NOTE Some PCI Express slots support only PCI Express graphics cards. If a RAID controller is installed in
one of these slots, the controller will not function. Refer to your computer documentation for information
about the PCI Express slot.

3. Press down gently, but firmly, to seat the card correctly in the slot.

4. Secure the controller to the computer chassis.

LSI Corporation

- 6 -