LSI 620j, 630j, CTS 2600 User Manual

CTS2600, 620j, and 630j Branding
Guide
48321-00, Rev A
July 2010
Revision History
Version and Date Description of Changes
Rev A Initial Document
LSI and the LSI logo are trademarks or registered trademarks of LSI Corporation or its subsidiaries. All other brand and product names may be trademarks of their respective companies.
!LIST ANY OTHER REQUIRED TRADEMARKS! REMOVE THIS STATEMENT!
This preliminary document describes a preproduction product and contains information that may change substantially for any final commercial release of the product. LSI Corporation makes no express or implied representation or warranty as to the accuracy, quality, or completeness of information contained in this document, and neither the release of this document nor any information included in it obligates LSI Corporation to make a commercial release of the product. LSI Corporation reserves the right to make changes to the product(s) or information disclosed herein at any time without notice. LSI Corporation does not assume any responsibility or liab ility arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by LSI Corpor ation; nor does the purchase, lease, or use of a product or service from LSI Corporation convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Corporation or of third parties.
FOR ALL DOCUMENTS UNDER NDA INCLUDE THE PARAGRAPH BELOW: REMOVE THIS RED TEXT
This document contains proprietary information of LSI Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of LSI Corporation.
FOR INTERNAL DOCUMENTS INCLUDE THE PARAGRAPH BELOW: REMOVE THIS RED TEXT
This document contains proprietary information of LSI Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of LSI Corporation.
Corporate Headquarters Email Website
Milpitas, CA globalsupport@lsi.com www.lsi.com 800-372-2447
Document Number: 4831-00, Rev A
LSI 2600, LSI 620j. and LSI 630j Branding Guide Overview of the CTS2600, 620j, and 630j
Branding Guide
CTS2600, 620j, and 630j
This document shows Systems Builders and Systems Integrators how to brand these building blocks to integrate them into their own branded solutions.
Overview of the CTS2600, 620j, and 630j
LSI provides unbranded CTS2600, 620j, and 630j systems to vendors so that Systems Builders and Systems Integrators can brand the systems and integrate them into their own branded solutions.
Figure 1 shows a three-quarter view and a front view of the CTS2600-24 and the 620j
for 24 2.5" drives. Figure 2 shows a three-quarter view and a front view of the CTS2600-12 and the 630j for 12 3.5" drives.
Figure 1: CTS2600-24 and 630j for 24 2.5" drive
Figure 2: CTS2600-12 and 630j for 12 3.5 inch drives
LSI Corporation Confidential | July 2010 Page 3
Branding Guide for the LSI 2600, LSI 620j. and LSI 630jCTS2600-24 and 620j for 2.5" drives
CTS2600-24 and 620j for 2.5" drives
CTS2600-24 and 620j drive canister Figure 3 shows the drive canister and LED displays of the CTS2600-24 and the 620j for
This section describes the branding specifications for the CTS2600-24 and 620j for 2.5" drives.
24 2.5" drives. Figure 4 shows the drive lever badge. Figure 5 shows the drive lever badge assembly and its branding specifications.
Figure 3: Drive canister and LED display of the CTS2600-24 and 620j
Figure 4: Drive lever badge of the CTS2600-24 and 620j
Page 4 LSI Corporation Confidential | ***Release Date***
Branding Guide for the LSI 2600, LSI 620j. and LSI 630j CTS2600-24 and 620j for 2.5" drives
Figure 5: Drive lever badge assembly of the CTS2600-24 and 620j
12. FOR ALL PARTS PURCHASED TO THE MECHANICAL DRAWING, EACH SHIPMENT MUST HAVE A CERTIFICATE OF COMPLIANCE LISTING THE MATERIAL LISTED BELOW AND THE PURCHASE PART NUMBER.
11. PART IDENTIFICATION:
BAG AND TAG WITH PART NUMBER, REVISION AND DATE.
10. RADII: EDGES AND CORNERS REPRESENTED SHARP IN 3D DATABASE MAY BE FILLETED
UPON APPROVAL.
9. SECONDARY OPERATIONS: NONE.
8. FINISH: PART MUST BE FREE FROM IMPERFECTIONS, SCRATCHES. NO FLASH OR TRIM MARKS ON SURFACE MARKED.
7. MATERIAL:
A.LCR530 RESIN WITH DK900 CATALYSIS 1.78 .25MM THICK ALTERNATE : LCR 54C
RTF RESIN WITH DK124 HV CATALYST 1.78 .25MM THICK.
B.13MM THICK POLYESTER. ARTWORK PRINTED DIRECTLY ON THE TOP SURFACE. C.BACKING ADHESIVE MATL : 3M 200MP ADHESIVE, ALTERNATE :3M 9172MP
ADHESIVE.
6. 3D DATABASE FEATURES TAKE PRECEDENCE OVER 2D DRAWINGS. REFER TO 3D DATABASE FILES(S)
5. DIMENSIONS ON ASSEMBLY DRAWINGS ARE REFERENCE DIMENSIONS. TOLERANCES ON THOSE DIMENSIONS NORMALLY REPRESENT VALUES ARRIVED AT THROUGH A STANDARD RSS TOLERANCE ANALYSIS. THEY ARE GOVERNED BY THE PROCESS CAPABILITY SECTION OF ENG STD 3-03-02.MEETING THE ASSEMBLY DIMENSION DOES NOT ABSOLVE THE REQUIREMENT THAT ALL PIECE PARTS MEET TOLERANCE AS WELL.
LSI Corporation Confidential | ***Release Date*** Page 5
Loading...
+ 11 hidden pages