Lsc T16F User Manual
User Instructions
Product Descriptions
This is a 4 channels foot control chaser, features 17 built-in chase patterns and 7 fixed scenes,
each pattern has four operating modes: Audio, Fast, Medium and Slow. When linkup, this unit
can be used as a either a Master or Slave. A DMX controller or a foot controller(supplied) can
be used to control this unit after proper connection.
Control & Functions
5
6
1
2
3
4
9
8
1. Channel Output: 5A/CH., Total 15A max.
2. Circuit Breaker: 15A
3. Linkup Selector: Move this slider to select between Master and Slave.
4. Function Selector: This slider is used to select Audio/Fast/Medium/Slow mode for the patterns.
5. Channel LEDs: These LEDs indicate the intensity of corresponding channel or activity of the
pattern or scene.
6. Stand By Button: This button serves several functions. In Master mode, tap this button to
activate or deactivate Stand By(its LED flashes when Stand By is active).
Pressing this button for three seconds can activate 17 chase patterns or 7
fixed scenes. When chase patterns are activated, each tap of Pattern button
will select a chase pattern. When the scenes are activated, each tap of Pattern
button will forward a scene step by step.
7. Pattern Button: In Master mode, use this button to select chase pattern or scene.
11
10
7
24-004-0918
Rev 1.0
8. Power Cable: AC 120V~60Hz, 15 A max.
9. Power Switch: Press to turn on/off the power.
10. DMX In: In Master mode, this connector can be plugged in a foot controller(supplied) for
remote control. In DMX mode, this connector is used to receive an incoming
DMX signal from either a DMX controller or DMX output(11) on another unit.
11. DMX Output: This connector can be used to link to next unit.
About the accessory:
The Foot Controller incorporating a 3-pin female
XLR connector is specially designed for cable
remote control of the T16F. When the T16F is in
Master mode, it serves as the two buttons: Pattern
and Stand by on the T16F, has the same functions
and operations.
Accessory(supplied)
Technical Specifications:
Power Input .................................................................................. AC 120V~60Hz, 15A max.
Channel Output ......................................................................................... 5A/CH., Total 15A
DMX In ................................................................................................ 3 pin XLR male socket
DMX Out .......................................................................................... 3 pin XLR female socket
Protection
Accessory(supplied) .......................................................................... Foot Controller x1 PC
Dimensions .................................................................................................. 220x155x60mm
Weight ........................................................................................................................... 1.6Kg
.............................................................................................. 15 A Circuit Breaker
Product Instructions:
I. Master mode: Slide Linkup selector(3) to "Master", this unit will serve as a Master,
you can use this unit directly or by a foot controller(sold separately).
By linkup function, several unit can be linked together and controlled
by the Master.(There is only a Master in the linkup.)
II. Slave mode: Slide Linkup selector(3) to "Slave", this unit will serve as a Slave, all
function buttons on this unit will be disabled and this unit will be controlled by the Master unit when available.
II. DMX mode Be sure the Linkup selector is in "Slave" position. Connect this unit with
a DMX controller, this unit will be controlled by the DMX controller. DMX
value 0-9 of DMX channel 1 activates Stand By, DMX value 10-249
leads to any of 7 scenes or 17 chase patterns. When the DMX value of
channel 1 is among 250-255, this unit will act as a 4 channel dimmer
pack and the start channel is the 2nd DMX channel.
IV. Stand By: Tap Stand By button(6) to activate Stand By, its LED flashes indicating
Stand By is active, which will kill all output momentarily. The second
tap of Stand By will deactivate this function.
V. Full On: Keep pressing Pattern and Stand By buttons at a time, Full On will be
activated, all output will be brought to full intensity. Release these two
buttons to leave.
Loading...