L&S SMART GATEWAY Technical Data Manual

SMART GATEWAY

Wi-Fi command interface / RF 433.92 MHz for connection between L&S
receivers and devices with Wi-Fi connection.

INDEX

1 - PRODUCT FEATURES

1.1 - TECHNICAL DATA

1.2 - USE

2 - NETWORK CONFIGURATION

2.2 - PROCEDURE FOR USING A HOTSPOT CONNECTION

2.3 - PROCEDURA PER L’UTILIZZO CON RETE WIFI ESISTENTE

3 - SYSTEM CONFIGURATION

3.2 - CREATING A DEVICE / ASSOCIATING THE DEVICE WITH THE RECEIVER

3.3 - DELETING OR MODIFYING A CREATED DEVICE

3.4 - CREATING A GROUP

3.5 - DELETING OR MODIFYING A CREATED GROUP

4 - GENERAL SETTINGS
5 - USER INTERFACE WINDOWS

5.2 - HOMEPAGE/DEVICES

5.3 - ZONES

5.4 - SCENARIOS

5.5 - PROGRAMMING THE TIMER

6 - FURTHER DETAILS

6.1 - CREATING A QUICK ACCESS COMMAND

6.2 - VERIFY THE NETWORK IP ADDRESS

7 - RECALL A SCENARIO USING TRANSMITTER

7.2 - ASSOCIATION OF THE TRANSMITTER

7.3 - ASSOCIATING A SCENARIO WITH THE TRANSMITTER KEY

7.4 - DELETING A TRANSMITTER

8 - RESET THE SYSTEM

8.2 - RESET THE SYSTEM CONFIGURATION

2.1 - INTRODUCTION

3.1 - INTRODUCTION

5.1 - INTRODUCTION

7.1 - INTRODUCTION

8.1 - RESET THE NETWORK CONFIGURATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may

025-FIS18_Smart_GATEWAY

cause undesired operation.

1

1 - PRODUCT FEATURES

1.1 TECHNICAL DATA

Power supply
Type of communication
Number of devices (mobile phones, PCs, etc.) simultaneously connected
Type of communication with receivers
Number of controllable receivers
Protection rating
Operating temperature
Dimensions

67mm

63mm

230Vac
Wi-
50

433.920MHz ISM
20
IP20

-20 +55 °C
174x46x35 mm

72mm

Picture 1.1b

KEY

Y key= reset network conguration
(if reset in hotspot with default password).
See paragraph 7.1

y

LED A

- Red/green/blue lights turn on in sequence when powered ON

- Flashes red while creating/connectiong to a network

- Blue light turn on if you set connecting to an existing network

- Red light turn on if you set creating a network hotspot

A

025-FIS18_Smart_GATEWAY

2

1.2 USE

To use the product you need:

- a Wi-Fi compatible device (e.g.: tablet, PC or Smartphone)

- Compatible radio receivers

To activate the system, follow the instructions in paragraph 2 on how to congure the hub network and access the
application. Next, follow the instructions in paragraph 3 on how to create user screens and associate them with the
receiver

2 - NETWORK CONFIGURATION

2.1 INTRODUCTION

The device can operate in two modes:

- the hub generates a Wi-Fi hotspot. To use the device, it must be connected to this network (therefore, not connected
to any other networks)

- connect the hub to an existing Wi-Fi network. Once congured, the hub can also be accessed when connected to the
existing network.

The rst solution is ideal for locations where no Wi-Fi network is available, but you wish to use a personal device for
driving the loads.
The second solution makes it possible to remain connected to existing Wi-Fi networks (e.g.: have internet access), while
using the hub at the same time.

According to the specications of the system, follow the instructions in:

- paragraph 2.2 to connect the hub for use with a hotspot

- paragraph 2.3 to connect the hub for use with an existing network

TYPE OF SYSTEM WITH HUB CONNECTED TO HOTSPOT

Device with Wi-Fi

Hub100
connection
(e.g.: Smartphone)

TYPE OF SYSTEM WITH HUB CONNECTED TO EXISTING WI-FI NETWORK

L&S
Receivers

Device with Wi-Fi
connection
(e.g.: Smartphone)

025-FIS18_Smart_GATEWAY

Existing Wi-Fi
Network

Hub100

L&S
Receivers

3

2.2 PROCEDURE FOR USING A HOTSPOT CONNECTION

STEP1

Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot

lampeggia rosso

STEP6

Click on "Congure network"
NOTE: this operation is not
necessary for usage, but it makes
the hub more secure and blocks
unwanted access to the system.

Congure network

STEP2*

The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar­tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.

Wi-Fi Activated

CHOOSE A NETWORK...

Hub Smart Control

STEP5

The user interface window will
open. Click on "menu".

menu

STEP3*

To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable

Hub Smart Control

ENTER PASSWORD

12345678

Access

STEP4*

You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.

Devices

Settings

Congure network

Congure system

STEP7*

You will be requested to enter a
password; the default password
is: “1234”.

Password

Enter password

1234

Conrm Cancel

*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi­ed previously, the system must
be reset; see paragraph 7.1.

Devices

STEP8

Click on "congure network"

congure network

Settings

CONFIGURE NETWORK

http://hub100.

Type a website address

STEP9

The current setting will be
displayed; click on "edit"

Congure network

Congure current network

Type of access : Hub hotspot

SSID : Hub Smart Control

Edit

Edit

025-FIS18_Smart_GATEWAY

4

STEP10

Click on "Hub hotspot"

Hub hotspot

Edit network

Select connection type

Hub hotspot

Wi-Fi network

STEP11

Fill in all elds with the connection data for the hotspot you wish to create.
Network name (SSID): the name of the hotspot generated by the hub.
See step 2 of this procedure (default: Hub Smart Control)
Current password: the existing password required to connect to the
hotspot used in step 3 of this procedure (default: 12345678)
New password: the new password which will be used in step 3.
It is recommended to set a new password for security reasons.
System name: the name to enter in the address bar of step 4 of this
procedure. The name cannot contain spaces.
NOTE: when entering the name in the address bar, it must always end with
a full stop (.)
EXAMPLE:
system name: “hubcasa”
address to enter: “http://hubcasa.”

ATTENTION:

To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured

STEP12

After lling in all the elds, click on
"Save" at the bottom of the page.

Network name (ssid)

Current password

New password

Conrm
password

System

System Name

Save

Save

Select connection type

Hub hotspot

Network wi

Network name (ssid)

Current password

New password

Conrm
password

System Name

STEP13

The hub will restart to activate the new settings;
the LED will ash red while creating the hotspot
(about 1 minute).
The personal device will disconnect from the hub’s
hotspot network.

Edit network

Hub hotspot conection

System

Save

NOTE:

it is important to remember the infor­mation entered as it is required in order
to use the hub with your own device
and to connect more devices at a later
time.

If the data are lost, the system must be
reset by following the procedure in
paragraph 7.1.

STEP14

To use the system, reconnect to the hub’s Wi-Fi
network (steps 2, 3 and 4 of this procedure) using the
new data entered during step 11.

NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1

025-FIS18_Smart_GATEWAY

5

2.3 PROCEDURA PER L’UTILIZZO CON RETE WIFI ESISTENTE

STEP1

Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot

lampeggia rosso

STEP6

Click on "Congure network"
NOTE: this operation is not neces­sary for usage, but it makes the
hub more secure and blocks
unwanted access to the system.

Congure network

STEP2*

The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar­tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.

Wi-Fi Activated

CHOOSE A NETWORK...

Hub Smart Control

STEP5

The user interface window will
open. Click on "menu".

menu

STEP3*

To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable

Hub Smart Control

ENTER PASSWORD

12345678

Access

STEP4*

You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.

Devices

Settings

Congure network

Congure system

STEP7*

You will be requested to enter a
password; the default password
is: “1234”.

Password

Enter password

1234

Conrm Cancel

*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi­ed previously, the system must
be reset; see paragraph 7.1.

Devices

STEP8

Click on "congure network"

congure network

Settings

CONFIGURE NETWORK

http://hub100.

Type a website address

STEP9

The current setting will be
displayed; click on "edit"

Congure network

Congure current network

Type of access : Hub hotspot

SSID : Hub Smart Control

Edit

Edit

025-FIS18_Smart_GATEWAY

6

STEP10

Click on "Wi-Fi network"

Network wi

Edit network

Select connection type

Hub hotspot

Network wi

STEP11

A list of existing networks detected by the hub will appear.
Select the network you wish to connect the device to, and enter the
password used to access the existing network.

Configure a static IP address:

IP ADDRESS: the network address to be associated with the hub.
If you know an available address in your network, enter it.
If you do not know this parameter, try to connect using the suggested
default address, or see paragraph 6.2.
This address will then be used to connect to the user command interface;
see step 14.

ATTENTION:

To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured; see
"URL" entry

Edit network

STEP12

After lling in all the elds, click on
"Save" at the bottom of the page.

SSID

Network1

Password

IP adress 192.168.1.200

Save

Encryption

Static IP setting

Save

Hub hotspot

Network wi

Password

IP adress

Net mask

STEP13

The hub will restart to activate the new settings,
and then connect to the existing Wi-Fi network.
The LED will ash blue during this phase (about 1
minute). After, will remain xed on blue.
The device will disconnect from the hub hotspot.
If the connection is unsuccessful see possible
causes below

Select connection type

Available Wi-Fi networks

SSID

Network1

Encryption

Static IP setting

192.168.1.200

255.255.0.0

Save

STEP14

To use the system:

- connect your device to the existing Wi-Fi network to
which the hub was connected

- open the browser and, in the address bar, type the
IP address which was saved in step 11
NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1

POSSIBLE REASONS FOR FAILURE TO CONNECT TO AN EXISTING NETWORK

Check the values entered in step 11 of this procedure.
The following are the most likely causes:

- incorrect network password: verify you have entered the correct network access password

- incorrect IP address: an address already in use, or incorrect address, was entered. See paragraph 6.2

- network not found: verify the Wi-Fi network is available

Make a reset (see paragraph 7.1) and do again this procedure from step 2.

025-FIS18_Smart_GATEWAY

7

3 - SYSTEM CONFIGURATION

3.1 INTRODUCTION

After the procedure in paragraph 2 is complete, the personal device is able to communicate with the hub.
The following step creates the various user command interfaces which will appear on the home screen of the application.
These interfaces can be either devices or groups.
Devices: the term device refers to an interface which is used to drive a load (e.g.: light or roller shutters)
Groups: the term ‘groups’ refers to an interface which is used to drive a set of previously created devices. This is useful for
creating a "switch OFF all lights" command or "lower all roller shutters" command.
To create devices, see paragraphs 3.2 and 3.3; to create groups, see paragraphs 3.3 and 3.4.
NOTE: both devices and groups will appear on the homepage. It is recommended to use the name which is assigned to
each interface to distinguish group commands from commands for a single device

3.2a CREATING A DEVICE

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP6

A list of created devices will
appear (the default list has no
devices).
Click on the "+" button to add
devices

STEP2

Click on "menu".

menu

Devices

STEP5

Click on "list of devices"

list of devices

STEP3

Click on "Congure system"

Congure system

Devices

Settings

Congure network

Congure system

STEP4*

You will be requested to enter a
password; the default
password is: “1234”.

1234

List of Devices

025-FIS18_Smart_GATEWAY

+

Congure system

LIST OF DEVICES

LIST OF GROUPS

RESET

Password

Enter password

Conrm Cancel

8

STEP7

The elds to ll in to create the device will appear:
NAME: the name which will appear on the homepage
TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor­med. This eld is chosen according to the receiver to be controlled. See the table below
ICON: the graphic icon which appears to the side of the device; for graphic purposes only

Congure system

Name

Type of
command

Icon

Save

STEP8

Click on "save" at the bottom of
the page.

Saving device

Deviced saved

TYPE OF COMMAND

On-Off

Open-Stop-Close

Impulse

Dimmer light

RGB/RGBW light

Tunable white light

EXECUTABLE ACTIONS

On - Off

Open - Stop - Close

Impulse

On - Off - Intensity setting

On - Off - Intensity setting - Colour management

On - Off - Intensity setting - Tunable light management

STEP9

The application displays the list
of updated devices. If you wish
to add more devices,
return to step 2 of this procedu­re.
If all user command interfaces
have been created, go to step

3.2b to associate them with the
central receivers.

NOTE

In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and
cannot be recovered, the system must be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings
(network name, page address, password).

The default password from "step 4" can be changed by accessing "menu-settings-change password".

025-FIS18_Smart_GATEWAY

9

3.2b ASSOCIATING THE DEVICE WITH THE RECEIVER

After the procedure in paragraph 3.2a is complete, the various devices which have been created will be displayed on the
homepage of the application.
The next step is to associate each device with the receiver to be driven.
The receiver must be accessed to complete this step.

PROCEDURE

STEP1

Access the receiver and perform the radio programming procedure for the multifunction radio transmitters.
See receiver manual.

THE LED TURNS ON

Make a short

press of

the button

SMART1

STEP2

While programming the radio, you will be requested to transmit a command. To transmit the command, select the
device on the homepage and transmit any command using the keys available.
The receiver ashes three times to conrm programming was successful.

Make a short press

of the button related to

the output which the

transmitter wants

to be programmed.

THE LED TURNS ON

SMART4

SELECT THE DEVICE ON THE HOMEPAGE AND TRANSMIT
ANY COMMAND USING THE KEYS AVAILABLE

025-FIS18_Smart_GATEWAY

LED MAKES 3 FLASHES
AND TURNS OFF

SMART1

LED MAKES 3 FLASHES
AND TURNS OFF

SMART4

10

3.3 DELETING OR MODIFYING A CREATED DEVICE

If you wish to delete or modify a created device, change the name, icon or the type of command, perform the following
procedure:

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP6

A list of created devices will
appear.
Select the device to be modied

STEP2

Click on "menu".

menu

Devices

STEP5

Premere su “lista dispositivi”

list of devices

STEP3

Click on "Congure system"

Congure system

Devices

Settings

Congure network

Congure system

STEP4*

You will be requested to enter a
password; the default
password is: “1234”.

1234

List of devices

Device 1

STEP7

Click on "edit” to change the
settings or "delete" to remove it

List of devices

Device 1

Congure system

LIST OF DEVICES

LIST OF GROUPS

RESET

Password

Enter password

Conrm Cancel

ATTENTION

In step 4 of the procedure, the default values to be used will be suggested.
If these were modied previously and cannot be recovered, the system must
be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3);
it will only reset the network settings (network name, page address,
password).

The default password from "step 4" can be changed by accessing
"menu-settings-change password"

Edit Delete

025-FIS18_Smart_GATEWAY

11

3.4 CREATING A GROUP

After creating several devices, a group (comprising several individual devices) can be created to send multiple load
commands with a single action.
This procedure offers the advantage of creating and modifying groups without having to access the central receivers; the
commands will be sent sequentially, i.e. in series. If, for example, the OFF command is sent to a group of three devices,
the three lights will power OFF in sequence.
To command groups simultaneously, perform the device creation procedure (paragraph 3.2a) and associate all the
receivers you wish to be part of the group, rather than a single device (paragraph 3.2b).

PROCEDURE:

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP6

A list of the created groups will
appear (the default list has no
devices).
Click on the "+" button to add a
group

STEP2

Click on "menu".

menu

Devices

STEP5

Click on "list of groups"

List of groups

STEP3

Click on "Congure system"

Congure system

Devices

Settings

Congure network

Congure system

STEP4*

You will be requested to enter a
password; the default
password is: “1234”.

1234

List of groups

+

Congure system

LIST OF DEVICES

LIST OF GROUPS

RESET

Password

Enter password

Conrm Cancel

025-FIS18_Smart_GATEWAY

12

STEP7

The elds to ll in to create the group will appear:
NAME: the name which will appear on the homepage
TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor­med.
This eld is selected according to the devices which are part of the group: for example, if the group includes a
combination of coloured lights and dimmer lights, and a type of command such as "RGB/RGBW lighting" is
selected, the dimmer lights will remain unchanged if a colour command is transmitted.

Congure system

Name

Select
devices

Type of
command

Icon

Save

STEP8

Click on "save" at the bottom of
the page.

Saving device

TYPE OF COMMAND

On-Off

Open-Stop-Close

Impulse

Dimmer light

RGB/RGBW light

Tunable white light

EXECUTABLE ACTIONS

On - Off

Open - Stop - Close

Impulse

On - Off - Intensity setting

On - Off - Intensity setting - Colour management

On - Off - Intensity setting - Tunable light management

STEP9

The application displays the list
of updated devices. If you wish
to add more groups, return to
step 2 of this procedure.

Deviced saved

ATTENZIONE

In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and
cannot be recovered, the system must be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings
(network name, page address, password).

The default password from "step 4" can be changed by accessing "menu-settings-change password"

025-FIS18_Smart_GATEWAY

13

3.5 DELETING OR MODIFYING A CREATED GROUP

If you wish to delete or modify a created device, change the name, icon or the type of command, perform the following
procedure:

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP6

A list of created groups will
appear.
Select the group to be modied

STEP2

Click on "menu".

menu

Devices

STEP5

Click on "list of groups"

list of groups

STEP3

Click on "Congure system"

Congure system

Devices

Settings

Congure network

Congure system

STEP4*

You will be requested to enter a
password; the default
password is: “1234”.

1234

List of groups

Light group 1

STEP7

Click on "edit” to change the
settings or "delete" to remove it

List of groups

Light group 1

Congure system

LIST OF DEVICES

LIST OF GROUPS

RESET

Password

Enter password

Conrm Cancel

ATTENZIONE

In step 4 of the procedure, the default values to be used will be suggested.
If these were modied previously and cannot be recovered, the system must
be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3);
it will only reset the network settings (network name, page address,
password).

The default password from "step 4" can be changed by accessing "menu-set­tings-change password"

Edit Delete

025-FIS18_Smart_GATEWAY

14

4 - GENERAL SETTINGS

4.1 EDITING THE GENERAL SETTINGS

The following settings can be modied:LINGUA: modica la lingua dei testi dell’applicazione
DATA/ORA: serve ad impostare data e ora all’interno dell’applicazione. Quest’impostazione è necessaria per utilizzare le
programmazioni orarie
PASSWORD: change the network and system conguration access password; see paragraphs 2 and 3

PROCEDURE

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP2

Click on "menu".

menu

Devices

STEP3

Click on "Settings"

Settings

Devices

Settings

Congure network

Congure system

STEP4

Click on the parameter you wish
to modify

Modica Elimina

Settings

CHANGE LANGUAGE

EDIT DATE/TIME

CHANGE PASSWORD

025-FIS18_Smart_GATEWAY

15

5 - USER INTERFACE WINDOWS

5.1 INTRODUCTION

Once the hub has been congured (paragraph 2), the devices have been created and
associated (paragraph 3.2), as well as any groups (paragraph 3.4), the application is
ready for use.
There are 4 main command screens:
HOMEPAGE / DEVICES: all created devices and groups are displayed in
alphabetical order; see paragraph 5.2
ZONES: the devices and groups can be divided into zones to facilitate use, see
paragraph 5.3
SCENARIOS: scenarios can be created by inputting different actions in different
devices; see paragraph 5.4
HOURLY PROGRAMMING: actions can be created for devices which
automatically activate at the desired time. See paragraph 5.5
To switch from one screen to another, click on the related icon. The red cursor indicates
which screen is active.

5.2 HOMEPAGE/DEVICES

The created devices and groups are displayed in alphabetical order on the homepage.
Each device will have its own user command interface according to the "type of
command" selected during the procedure in paragraph 3.2a.
The following example describes each type of interface along with its functionality.
NOTE: in the example, the device name which appears on the homepage corresponds
to the type of command; the name entered by the user during the procedure in
paragraph 3.2 will appear, in a real situation

Devices

Icon of the selected screen

Devices

Open-Stop-Close

Impulse

Dimmer Ligh

%

RGB/RGBW light

RGBCCT

Tunable white light

On-Off

Type of command "Open-Stop-Close" Type of command "Impulse"

Device name Device name

025-FIS18_Smart_GATEWAY

16

Type of command "Dimmer Light" Type of command “On-Off”

Device name

ON OFF

Intensity

Type of command "RGB/RGBW Light"

Device name

Color Memo

Click on

ON OFF

<

Device name

R:25 G:142 B:191

Device name

ON OFF

Save:

Saves light colour setting for
the next time it is powered ON

White Light:

sets the white light

:

play / stop cycle

Intensity

Type of command "Dynamic White Light"

Device name

Color Memo

Click on

ON OFF

Save

Effect Effect speed

Device name

<

White light

R G B

RGB:
sets the three values for R, G and B

Effect speed:

colour settings for the colour cycle

Effect speed:

sets the duration of the colour cycle

Save:

Saves light temperature setting
for the next time it is powered ON

Neutral white:

sets the neutral white light

Intensity

025-FIS18_Smart_GATEWAY

Memo Bianco neutro

17

5.3 ZONES

The default setting of the zones screen is empty.
The user can reorganise the created devices and groups (displayed on the homepage screen) to facilitate access and use.
EXAMPLE:
CI create the "living room" zone where I insert both the lights and the roller shutters in the room.
I create the "garden" zone which includes the devices located in the garden.

PROCEDURE FOR CREATING ZONES

STEP1

Click on the zones icon. Only devices which have
been divided and organised into zones are displayed.

Zones

Zone

STEP2

Click on the "+" icon.
The zones creation menu will open

+

Zones

STEP4

The application returns to the "zones" menu and
displays the created zones. To create more zones,
return to step 2

Zones

Living room

Dimmer light

%

RGB/RGBW light

RGB

STEP3

Enter the name of the zone (e.g.: living room) and
select the devices and groups which are in the zone;
now click on "save zone".

List of

devices

List of

groups

New zone

Name

List of device

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white lightOn-Off

List of groups

Ground oor lights

Living room

Save zone

Save

Name
of the zone

Selection

025-FIS18_Smart_GATEWAY

18

PROCEDURE FOR DELETION OR MODIFICATION OF CREATED ZONES

If you wish to delete or modify a created zone, change its name or the devices which are a part of the zone,
perform the following procedure:

STEP1

Click on the zones icon. Only devices which have
been divided and organised into zones are displayed.

Zones

Living room

Dimmer light

%

RGB/RGBW light

RGB

Zone

STEP2

Click on the "pencil" icon. The "gear" icon is
displayed next to each zone.

pencil

Zones

Living room

Dimmer light

gear

%

RGB/RGBW light

RGB

STEP4

EDIT: modify the values and click on "Save zone"
DELETE: click on the "recycle bin" icon

New zone

Nome

List of device

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
On-Off

List of groups

Ground oor lights

Save Recycle bin

Living room

Save zone

STEP3

Click on the name of the zone you wish to delete or
modify. The zone settings menu will be displayed,
along with the parameter settings.

New zone

Name

List of device

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
On-Off

List of groups

Ground oor lights

Living room

Save zone

025-FIS18_Smart_GATEWAY

19

5.4 SCENARIOS

"Scenario" commands, or rather a command which brings the status of various devices to the set value, can be created
through the procedure described below.
Once created, the scenarios can be recalled by clicking on the dedicated key on the scenario interface; see step 6 of the
procedure or create a time setting.
Scenario commands are sequential (a command is transmitted to one device at a time).
EXAMPLE:
SCENARIO 1: the white lights power OFF and the suffused blue light powers ON

PROCEDURE FOR CREATING SCENARIOS

STEP1

Click on the scenarios icon.
Any created scenarios will be displayed.

Scenarios

Scenarios

STEP5

The application returns to the "scenarios" menu and
displays the created scenarios. To create more
scenarios, return to step 2.

Scenari

Total Off

STEP2

Click on the "+" icon.
The scenarios creation menu will open.

Scenarios

+

STEP4

Enter the name of the scenario (e.g.: power OFF
everything) and select the devices involved and their
action.

New scenario

Title

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
On-Off

Total Off

Title

Select device

See/edit action settings

Save scenario

STEP6

To recall the scenario which has been set, press the "Play" icon on the
scenarios screen.
To create a time setting which automatically activates the scenario at a
scheduled time and day; see paragraph 5.5.

025-FIS18_Smart_GATEWAY

Scenarios

Total Off

Play scenario

20

PROCEDURE TO DELETE OR MODIFY CREATED SCENARIOS

If you wish to delete or modify a created scenario, change its name or the actions of the devices, perform the
following procedure:

STEP1

Click on the scenarios icon.
Any created scenarios will be displayed.

Scenari

Scenari

STEP4

EDIT: modify the values and click on "Save scenario"
DELETE: click on the "recycle bin" icon

Edit scenario

Title

Total Off

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
On-Off

Title

Select device

See/edit action settings

STEP2

Click on the "pencil" icon.
The "gear" icon is displayed next to each scenario.

Scenarios

Pensil

Total Off

Gear

STEP3

Click on the name of the zone you wish to delete or
modify. The settings menu will be displayed, along
with the parameter settings.

Edit scenario

Title

Total Off

Open-Stop/Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
On-Off

Save scenario

Save Recycle bin

Save scenario

025-FIS18_Smart_GATEWAY

21

5.5 PROGRAMMING THE TIMER

ATTENTION: To operate correctly, the date and time must be set following the procedure in paragraph 4.
ATTENTION: in case of power failure you must updated the time manually, where possible, therefore, it is advisable
to connect the hub to a UPS.

The following procedure is used to create timer settings, meaning the creation of time setting for the automatic transmis­sion of one or more commands from a scenario at a scheduled time and day of the week.
EXAMPLE: time setting 1: the roller shutters open at 7 A.M., from Monday to Friday

PROCEDURE FOR CREATING TIMER SETTINGS

STEP1

Click on the timer settings icon. Any created settings
will be displayed.

Time setting

Time setting

STEP4

Click on the "clock" icon.

New time setting

Title

List of devices

Open-Stop/Close 1
Open-Stop/Close 2
Luce Dimmer
Luce RGB/RGBW
Luce Bianco dinamico
On-Off

Time setting

Wake Up

Clock icon

STEP2

Click on the "+" icon.
The timer settings creation menu will open.

Time setting

+

STEP3

Enter the name of the timer setting (e.g.: morning
wake up) and select the devices involved and their
action.

New time setting

Title

List of devices

Open-Stop/Close 1
Open-Stop/Close 2
Luce Dimmer
Luce RGB/RGBW
Luce Bianco dinamico
On-Off

Time setting

Wake Up

Title

Device setting

See/edit action settings

Save

STEP5

Set the time and the days you wish the action to be
performed and click on the "OK" key to conrm.

When

min

11h20

121321

22

Monday

Tuesday

Wednesday

025-FIS18_Smart_GATEWAY

OK

Thursday

Friday

Saturday

Sunday

Hour:
scroll through the hours and
minutes and click on the selected value

Days:
Select the days of the week

"OK" key

Save

STEP6

The application returns to the "timer settings" menu.
To create other settings, return to step 2. Timer
settings can be activated/deactivated.

Time setting

Wake Up

Activate/Deactivate timer setting

22

NOTE

- If you wish to create events which automatically activate and deactivate (e.g.: the lights power ON at a set time and
power OFF at a later time), create two timer settings.

- Once created, the settings can be activated and deactivated by clicking on the dedicated key on the on the timer
settings interface; see step 6 of the procedure.

- the commands transmitted by the hub are sequential (e.g.: if the action consists of powering OFF three lights, they will
be powered OFF one at a time).

PROCEDURE TO DELETE OR MODIFY CREATED TIMER SETTINGS

If you wish to delete or modify created timer settings, change its name, the actions of the devices or the automatic
time settings, perform the following procedure:

STEP1

Click on the timer settings icon. Any created settings
will be displayed.

Time setting

Programming the timer

STEP4

EDIT: modify the values and click on "Save"
DELETE: click on the "recycle bin" icon

New time setting

Title

Wake Up

List of devices

Open-Stop/Close 1
Open-Stop/Close 2
Luce Dimmer
Luce RGB/RGBW
Luce Bianco dinamico
On-Off

Time setting

Title

Device setting

See/edit action settings

STEP2

Click on the "pencil" icon. The "gear"
icon is displayed next to each setting.

Time setting

Wake Up

Gear

STEP3

Click on the name of the setting you wish to delete or
modify. The settings menu will be displayed, along
with the parameter settings.

New time setting

Titolo

List of devices

Open-Stop/Close 1
Open-Stop/Close 2
Luce Dimmer
Luce RGB/RGBW
Luce Bianco dinamico
On-Off

Time setting

Wake Up

Save

025-FIS18_Smart_GATEWAY

Save

23

6 - FURTHER DETAILS

6.1 CREATING A QUICK ACCESS COMMAND

The creation of a quick access command for the application makes it easier to use.
The procedure differs depending on the type of device in use. Several examples are described below:

ANDROID

1 - Start up Chrome for Android and open the application page according to the settings in paragraph 2
2 - Click on the "Menu" button in Chrome, then click on "add to home screen".
3 - Give the link a name and Chrome will then add it to the homepage.
Almost all other Android compatible browsers have this feature; in Firefox for Android, for example, simply click on the
menu button, then Page, and Add to Home.

IPHONE, IPAD, AND IPOD TOUCH

1 - Start up Safari on the Apple iOS and open the application page according to the settings in paragraph 2
2 - Click on the Share button in the toolbar of the browser (the rectangle with an arrow facing upwards which is located
in the upper part of an iPad display, and in the lower part of an iPhone or iPod Touch display) and click on "Add to
Home"
3 - You will be requested to assign a name to the link before clicking the “Add” button.
Other browsers, such as Chrome for iOS, do not have this function due to the limitations of iOS.

WINDOWS

1 - Start up Chrome and open the application page according to the settings in paragraph 2
2 - Click on the options icon (the three dots located at the top of the display, to the right of the address bar), click on
“More tools”, then click "Add to desktop".
With Internet Explorer, simply click on the settings icon (the gear icon located at the top of the display, to the right of
the address bar), then click on "Add site to Start menu".

025-FIS18_Smart_GATEWAY

24

6.2 VERIFY THE NETWORK IP ADDRESS

Using a Smartphone connected to the existing network, the IP address of your network can be displayed.

ANDROID

1 - Open the settings menu to view the available network connections
2 - Verify you are connected to the network for which you want to know the address, then click on the network name to
display the information
3 - Display the "IP Address"
When the hub is connecting, the IP address which contains the same rst three numbers as those displayed, and the
nal modied number, must be used (see the example). If you do not know an available address to enter as the nal
number, try using numbers from 150 to 250.

EXAMPLE:
IP address displayed: 192.168.1.6
IP address to enter in the hub: 192.168.1.200

IPHONE, IPAD, E IPOD TOUCH

1 - Open the settings menu to view the available network connections
2 - Verify you are connected to the network for which you want to know the address, then click on the "info" icon to the
right of the network name
3 - Scroll through the menu until "IP Address" is displayed
When the hub is connecting, the IP address which contains the same rst three numbers as those displayed, and the
nal modied number, must be used (see the example). If you do not know an available address to enter as the nal
number, try using numbers from 150 to 250.

EXAMPLE:
IP address displayed: 192.168.1.6
IP address to enter in the hub: 192.168.1.200

025-FIS18_Smart_GATEWAY

25

7 - RESET THE SYSTEM

7.1 RESET THE NETWORK CONFIGURATION

This procedure deletes the network congurations set under paragraph 2, then the hub restarts in hotspot mode with the
default passwords.
The default password to access the network and system conguration will also be reset.
NOTE: any devices groups, zones, scenarios and timer settings will be deleted

STEP1

Press and hold the reset key until
the LED begins to ash

STEP2

Press and release the key again.
The LED ashes quickly and
powers OFF

RESET

KEY

PRESS FOR
8 SECONDS

RESET

KEY

SHORT

PRESS

Following this procedure, the values will be those indicated in the procedures from paragraph 2 and 3 of this manual.

025-FIS18_Smart_GATEWAY

26

7.2 RESET THE SYSTEM CONFIGURATION

This procedure deletes any devices, groups, zones, scenarios and timer settings.

STEP1

Access the application according
to the network conguration
performed in paragraph 2

STEP6

Click on Reset

STEP2

Click on "menu".

menu

Devices

STEP5

Click on "Reset"

Reset

STEP3

Click on "Congure system"

Congure system

Devices

Settings

Congure network

Congure system

STEP4*

You will be requested to enter a
password; the default
password is: “1234”.

1234

Reset Impianto

Delete all Devices,

Groups, Zones,

Scenarios and Time settings?

Reset

Reset

STEP7

The system will be restored

Reset system

System restored

Congura impianto

LISTA DISPOSITIVI

LISTA GRUPPI

RESET

Password

Enter password

Conrm Cancel

ATTENZIONE

In step 4 of the procedure, the default values to be used will be suggested.
If these were modied previously and cannot be recovered, the system must
be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3); it
will only reset the network settings (network name, page address, password).

The default password from "step 4" can be changed by accessing "menu-set­tings-change password".

025-FIS18_Smart_GATEWAY

27

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

FCC NOTE:

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure environment.

To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully

supported by the operating and installation configurations of the transmitter and its antenna.

025-FIS18_Smart_GATEWAY

WARNING

Save these instructions.The instructions for use must be scrupulously complied with during

installation and use.

TECHNICAL DATA

- Rating for protection against dust, solid objects and moisture: IP20 (Standard Ref. EN 60529 –

EN 60598-1)

KEY TO SYMBOLS (for EUROPE)

Appliance in class III. The power appliance must be very low voltage security. Use

only power supplies guaranteed SELV or SELV equivalent . (Standard Ref. EN

61347-2-13).

DEMOLITION AND DISPOSAL OF THE LIGHTING APPLIANCE

The appliance should be considered as EEE (electrical and electronic equipment)

and must be disposed of as such.

The symbol shown below indicates that at the end of its life the equipment is to be considered

WEEE (waste electrical and electronic equipment).

As such the appliance may not be disposed of as mixed municipal waste, but must be taken

to the special collection centres set up by the local au¬thorities or by the manufacturers, who

will arrange for the separate collection of WEEE.

When purchasing a new appliance, an old appliance to be disposed of may also be handed

over to the distributor.

Contact the competent authorities or the distri¬butor/manufacturer for further information on

the matter.

MAINTENANCE

In case of failure, replace the whole set.

28