T9100 &
Cancel Panel
Paging System Transmitter
U S E R M A N U A L
Installation, Warranty and Service Information
Long Range Systems, Inc.
4550 Excel Parkway, Su ite 200
Addison, TX 75 001
800. 437.4996 •www.pager.net
Table Of Contents
The T9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Provided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Optional Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Overview of T9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rest Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the T9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cancel Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
User Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display Current Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Antitheft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Vibe Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Keytone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preset Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Repaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Repeater Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Duty Pager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Restaurant ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Station ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
POCSAG (FM) Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Edit Manager Pager Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset to Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Server Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Range Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Find ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Three Digit POCSAG Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Pager Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Long Range Systems 1 T9100 User Manual
T9100 Cancel Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Overview of T9100 Cancel Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the T9100 Cancel Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cancel Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
User Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Paging from Cancel Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Associating the T9100 Cancel Panel to T9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Changing Transmitters as 2.4 GHz Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Service Questions and Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
LRS PAGERS AVAILABLE FOR THE T9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USING THE SP5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Reprogramming and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
USING THE LRS ALPHA E467 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Read Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Delete Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Time/Date Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Auto ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set Keytone On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Select Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
USING THE STAR PAGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cleaning & Charging Instructions for LRS Paging Equipment . . . . . . . . . . . . . . . . . . . . . . 30
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Long Range Systems 2 T9100 User Manual
THE T9100 Installation:
Hardware Provided
Each transmitter kit contains the transmitter, Instruction Booklet, two antenna, one 9VAC 1.5A power adaptor, one Staff Name board, and four mounting bracket kits.
Optional Hardware
The T9100 and T9100 Cancel Panel have the ability to print a server report to a POS Printer. Contact LRS if
you wish to purchase a printer.
Hardware Setup Procedure
1. Remove all items from their packaging.
2. Locate the silver connector on the top of the transmitter. Twist the antenna (about 3” long, BNC,
silver bottom) onto the connector.
3. Locate the gold connector on the top of the transmitter. Twist the antenna (about 4” long, SMA,
bends at right angle) onto the gold connector.
Note: Both antennas must be attached before turning on transmitter. Do not remove either an-
tenna at any time due to risk of damage.
4. Mount the power supply in convenient location with access to 110V power.
Mounting the Transmitter
The T9100 is designed to be mounted in various ways to accommodate the kitchen environment: to a horizontal surface (i.e. table, counter, shelf), to a vertical surface, or hanging to a wall or stand.
Caution: Mounting with the antenna near any large metal objects will degrade the operating range.
To place on a wall or stand, locate the four slots on the mounting plate. Then align four wall anchors (5mm
diameter) into the wall to the mounting plate.
Panel and Wall Mount
Mounting Holes
Long Range Systems 3 T9100 User Manual
For mounting to surfaces, place the mounting
brackets into the captive nuts for either horizontal
or vertical mounting. There are two sets of 4 cap-
ive nuts for mounting to horizontal surfaces, and
t
one set of captive nuts for mounting to vertical
surfaces.
Captive Nuts
To attach the clamps:
1. Align the mounting nuts to the clamps.
2. Use the #10-32 x 3/8” screws to hold
the clamps. Do not fully tighten
screws.
Clamp
Captive Nuts
Screws
3. Adjust the distance between clamps
until fits to the mounting surface.
4. Tighten screws.
Long Range Systems 4 T9100 User Manual
. Place the thumbscrew into the clamp op-
5
posite the one with the foam pad.
. Attach the foot of the thumbscrew.
6
. Adjust position of thumbscrew and tighten
7
to hold the transmitter in place.
Clamp with
oam Pad
F
Thumbscrew
Foot
Thumbscrew
Turn clockwise
to tighten
Turn counter-
clockwise to
loosen
Because the thumbscrews and brackets can be
mounted in many ways, they can be adapted to
most locations is possible.
Thumbscrew
Horizontal Mount
Mounting
Bracket
Mounting
Screws
Vertical Mount
Thumbscrew
Mounting
Bracket
Long Range Systems 5 T9100 User Manual
Mounting
Screws
Power Connection
. Plug the power supply into a standard 110V outlet and the barrel connector end into the jack on
1
the side of the transmitter.
. Upon completion of the setup, make sure pagers are fully charged.
2
Long Range Systems 6 T9100 User Manual
Overview of T9100
1
2
3
4
5
6
7
8
9
1
0
M1
M2
8
6
C
L
R
P
R
O
G
E
N
T
V
1
V
2
V
3
www.pager.net
0
CANCEL PANEL
Antenna
Status LED
Cancel Keys
Printer
Port
Reset Terminals
Function Keys
Number Keys
Vibration Keys
Power
Supply
Keypad
Function Keys
The function keys are located along the bottom row of the T9100.
- M1 & M2 used to page and program Manager Pagers.
- 86 “All Call” button used to page all pagers.
- CLR used to clear an entry or to back up one menu level.
- PROG press once to program pagers, press a second time to access the menu functions.
- ENT used to enter functions.
Vibration Keys
V1, V2 and V3 select the number of vibrations a pager will respond with. This button is pressed before paging a pager. Sends message 1, 2 or 3 to Alpha pagers.
Number Keys
Number keys 1 through 10 located along the center row. Number 10 is also 0 when Programming, using the
Menus, or paging pagers greater than 10.
Long Range Systems 7 T9100 User Manual
Cancel Keys
The row of keys located below the display. These keys will cancel a call to the pager number shown on the
isplay immediately above the respective key. The Cancel Keys also are used during menu selection.
d
Antenna
he T9100 utilizes 2 antennas when transmitting.
T
UHF antenna, located to the user’s left, is used to communicate with the LRS pagers.
A
A 2.4 GHz antenna, located to the user’s right, communicates with the T9100 Cancel Panel.
Reset Terminals
The Reset Terminals are located to the user’s left side on the transmitter. These are used to reset a pager for
programming.
Status LED
This LED will light green to indicate that the T9100 is sending information to the pagers or T9100 Cancel
Panel.
System Specifications
Notice: Operation is subject to the following:
• This device may not cause interference
• This device will accept any interference including interference that may cause undesired operation of the unit.
Required Voltage: One 110/220V outlet for the T9100 transmitter
Operating Frequency: 420-470 MHz
Radiated Power: < 4900 micro-volts/meter
Operating Range: Dependent upon pagers used
Long Range Systems 8 T9100 User Manual
Using the T9100
Time and Date
Initial Power Up
uring power up, to enter the time and date:
D
• At [enter time], enter the hh mm (hour, minute) using the number keys, and then press ENT.
• Press 2 for AM or 10 for PM.
• At [date], enter the mm dd yy (month, day, year) using the number keys, and then press ENT.
Clock Menu
The time and date can also be set from the Clock menu by:
• Press PROG – PROG – 1 – ENT.
• Press the button under set.
• At [enter time], enter the hh mm (hour, minute) using the number keys, and then press ENT.
• Press the button under AM or PM.
• At [date], enter the mm dd yy (month, day, year) using the number keys, and then press ENT.
• If done, press Yes (button under Yes), if not, press No (button under No.)
Note: The transmitter will use a default selection of “Yes” after 30 seconds of inactivity.)
Send Time
This feature will automatically send the current time and date to the pagers every 15 minutes. The default
setting is OFF.
To enable:
• Press PROG – PROG – 1 – ENT.
• Press button under Send.
• At [Auto] select button under ON.
• If done, select Yes (button under Yes), if not, select No (button under No.)
To disable:
• Press PROG – PROG – 1 – ENT.
• Press button under Send.
• At [Auto] Press select button under OFF.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Paging
To page pagers 1 through 99, enter the 2 digit pager number using the number keys. The 10 key also is used
as the 0 key.
All Call
If all staff pagers need to be called at once, press the 86 key.
Manager Pagers
To page the managers, press the M1 for the #1 manager pager or M2 for the #2 manager pager.
Cancel Page
To clear/cancel a pager to the server, press the Cancel Key under the pager number.
Long Range Systems 9 T9100 User Manual
User Preferences
The T9100 will come with factory settings for normal operating use. Some features can change per the user’s
ustom needs.
c
Display Current Settings
To view the current settings for the transmitter:
• Press PROG – PROG – 1 – 6 – ENT.
• Press ENT to scroll through each item:
• Date
• Restaurant ID Number
• Station ID Number
• FM Start point
• Pre-canned Message
• Repage interval
• M1 (Manager 1) information
• M2 (Manager 2) information
• Duty Pager information
• Router Set
• Cancel Panel set to page (yes or no) (Note: Only seen on Cancel Panel)
• UHF Master
• T9100 is set to Master (yes or no)
• Node ID
• Pan and Channel ID
• Channel Scan is on or off
• Synched on or off
• Beeper (keytone) is on or off
• Code Version
• Error Count
• If done, press 6 for Yes, if not, press 10 for No.
Antitheft
Note: This feature is ONLY for text pagers.
This feature will make a pager beep and/or vibrate continuously if goes beyond the range of the transmitter.
To enable:
• Press PROG – PROG – 4 – ENT.
• At [theft] press button under ON.
• If done, select Yes (button under Yes), if not, select No (button under No.).
To disable:
• Press PROG – PROG – 4 – ENT.
• At [theft] press button under OFF.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Long Range Systems 10 T9100 User Manual
Display Clock
The default setting for the clock is ON during normal operation.
To disable:
• Press PROG – PROG – 1 – 0 – ENT.
• Press button under Clock for the Clock sub-menu.
At [clock] Press button under OFF.
•
• If done, select Yes (button under Yes), if not, select No (button under No.)
To enable:
• Press PROG – PROG – 1 – 0 – ENT.
• Press button under Clock for the Clock sub-menu.
• At [clock] Press button under ON.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Vibe Level
The default Vibration Level for pagers can be set via:
1. Pressing the V1, V2, or V3 buttons for levels 1, 2, and 3 respectively.
2. From the menus:
• Press PROG – PROG – 1 – 2 – ENT.
• Enter a value of 1, 2, or 3 from the keypad
• If done, select Yes (button under Yes), if not, select No (button under No.)
Keytone
The transmitter default is for tones to sound with each key press.
To disable:
• Press PROG – PROG – 2 – 2 – ENT.
• At [beeper] press button under OFF.
• If done, select Yes (button under Yes), if not, select No (button under No.)
To enable:
• Press PROG – PROG – 2 – 2 – ENT.
• At [beeper] press button under ON.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Long Range Systems 11 T9100 User Manual
Preset Message
The LRS transmitters come with a list of preset messages that can be sent to Alpha Pagers. To edit which
message is sent:
Press PROG – PROG – 1 – 3 – ENT.
•
• Enter the preferred message from the table, then press ENT.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Pre Loaded Messages
000 Phone Call
001 Sales Call
002 Manager
003 Customer
004 Room
005 Visitor
006 call Ext
007 MTG Room
008 Lane
009 Aisle
010 Void
011 Stamps
012 Change
013 Station
014 Machine
015 Operator
020 Starter
021 Service drive
022 Showroom
023 Parked Call
024 Voice Mail
025 Dressing room
026 Price check
027 Department
028 Cashier
029 Office
030 Table
031 Winner
032 Pickup
033 Dock
034 You have mail
035 Table ready
040 Door
041 Survey
042 T-nnn Q-mm
043 Break
044 Fire
045 Unit
046 Window
047 Nurse
048 Register
049 Owner
050 Check
051 Drink
052 Food
053 Service
054 Seat
055 Booth
060 Car
061 Bus
062 Bay
063 Low battery
064 Error
065 Exit
066 Fax
067 host
068 Space
069 Location
070 Nursery
071 Teller
072 Officer
073 Buffet
074 Diaper change
075 Child crying
016 Emergency
017 XX Minutes
018 Tee
019 Pro Shop
036 No special
037 Hole
038 Kitchen
039 Bar
056 Lobby
057 Help
058 Restroom
059 Valet
076 To nursery
Repaging
Repaging sends repeated messages to the pagers.
Note: This feature requires use of an associated Cancel Panel to work.
Server
To set the re-page time for Server pagers:
• Press PROG – PROG – 6 – ENT.
• Press button under Repage.
• At [time] use the number keys to enter as mm ss (minute, seconds), then press ENT. The screen
will briefly show the updated re-page time.
Long Range Systems 12 T9100 User Manual
• If done, select Yes (button under Yes), if not, select No (button under No.)
Manager
To set the Manager to be paged once after the third re-page:
• Press PROG – PROG – 6 – ENT.
• Press button under More.
• At [mgr] press button under Mgr.
Press button On.
•
• If done, select Yes (button under Yes), if not, select No (button under No.)
To turn Off the Manager to be paged:
• Press PROG – PROG – 6 – ENT.
• Press button under More.
• At [mgr] press button under Mgr.
• Press button under Off.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Repeater Delay
When using a repeater it may be necessary to add a delay between pages when paging multiple pagers to
allow the repeater time to repeat the signal and detect the next one. Default setting is OFF.
To add repeat Delay:
• Press PROG – PROG – 6 – ENT.
• Press button under More.
• Press button under repeater.
• At [rPt], press button under ON to enable the Repeat Delay. Press button under OFF to disable
Repeat Delay.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Duty Pager
The duty pager is used to remind someone of a periodic repetitive task. To setup:
• Press PROG – PROG – 7 – ENT.
• At [duty] press button under On. (After 10 seconds, the screen will default to Off.)
• Enter the Duty Pager number with the keypad, then press ENT.
• Enter Vibe Level (value of 1, 2, or 3), then press ENT.
• Enter the repage time as mm ss (minutes, seconds), then press ENT.
• Screen will briefly display the new settings.
• If done, select Yes (button under Yes), if not, select No (button under No.)
To disable the Duty Pager:
• Press PROG – PROG – 7 – ENT.
• At [duty] press button under Off.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Restaurant ID
The ID of the Restaurant system. Set if more than one LRS system is in an area to prevent interference. To set:
• Press PROG – PROG – 1 – 4 – ENT.
Long Range Systems 13 T9100 User Manual
• At [rest ID], enter a value from 0 to 9, and then press ENT.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Station ID
The station that will be displayed on a pager if more than 1 station is in use. To set:
• Press PROG – PROG – 1 – 1 – ENT.
At [stn ID], enter a value from 0 to 9, and then press ENT.
•
• If done, select Yes (button under Yes), if not, select No (button under No.)
POCSAG (FM) Start
• Press PROG – PROG – 8 – ENT.
• Press button under FM Start (Note: A 10 second delay will default to FM Start).
• Set the start point at value from 00 to 99, and then press ENT.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Edit Manager Pager Number
In the event the Manger’s pager numbers are changed, to change the T9100:
• Press PROG – PROG – M1. (or M2)
• At [MGR1 num], enter the new manger number from the keypad (value from 0 to 99), then press ENT.
• Enter the Vibration Level (Value of 1, 2, or 3), then press ENT.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Reset to Factory Default
Note/Caution: If you reset the T9100 to factory defaults the system ID, vibration mode, and sta-
tion ID could be reset and you may have to re-set these to work with your exist-
ing pagers. If you still want to proceed with this function, do the following:
• Press PROG – PROG – 2 – 1 – ENT.
• At [reset] press button under Yes. (Select No to keep current settings.)
• If done, select Yes (button under Yes), if not, select No (button under No.)
Server Statistics
The T9100 can track the daily statistics of the number of times a server was paged, the server’s average response time, and the number of times a manager is paged.
To enable Server Statistics:
• Press PROG – PROG – 2 – 3.
• Press ENT.
• At [Stats], press button under ON.
• Enter the start time (example 3 for 3 AM or 3 PM) and then press ENT.
• Press button under AM or PM.
• The transmitter’s memory will clear.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Note:
• At the set time, the daily report will print to the POS Printer.
• At the set time, the memory will also clear to begin a new set of daily statistics.
To disable the Server Statistics:
• Press PROG – PROG – 2 – 3.
Long Range Systems 14 T9100 User Manual
• Press ENT.
• At [Stats], press button under OFF.
If done, select Yes (button under Yes), if not, select No (button under No.)
•
Printing Statistics
Note: S
er must be set as UHF Master.
t
he current POS Printer supported for the T9100 is the Star TSP650.
T
erver Stats needs to be turned ON before stats can be viewed or printed. The transmit-
The connection between the transmitter and printer is a “straight-through”. This is achieved with a standard
DB9 to DB25 adapter connected to the back of the printer, and a LRS provided serial cable to connect the
printer to the transmitter.
If the user attempts to use a “null cable” between the printer and the transmitter, a “null modem” will need
to be added in-line to correct the connection.
To print a current view of the Server Statistics:
• Press PROG – PROG – 2 – 4 – ENT.
• Enter a server number and press ENT.
• Press button under PRINT.
• The statistics will now print.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Note: The Statistics will also print at the time set in the Stats menu.
Example Print
Date:
Time:
Server Response Report
Svr Pages A.R.T. Mgr
1500:44 02
5400:29 01
12 3 00:15 --
17 4 00:25 01
--------------------------------------------------------------
Svr = Server
Pager = # of pages in last 24 hours
A.R.T. = Average Response Time
Mgr = # of times manager was paged
Viewing Statistics
To View the current Server Statistics:
• Press PROG – PROG – 2 – 4.
• Enter a server number and press ENT.
• Press button under VIEW.
• Press ENT to scroll through the list of servers. (The list will start at the number entered and will
continue to the end of the list or until CLR is pressed.)
• If done, select Yes (button under Yes), if not, select No (button under No.)
Long Range Systems 15 T9100 User Manual
Example Statistics View:
Server#
# of Pages in
24 hr Period
Average
Response time
# of Times
Manager Paged
(mm:ss)
1
05
00:44
02
Range Test
This can be used to determine the effective range of the T9100 in your environment. To start the range test:
• Press PROG – PROG – 8 – ENT.
• Press button under Range. The Range Test will begin automatically.
• Stop the Range Test by pressing any button.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Find ID
• Press PROG – PROG – 1 – 0 – ENT.
• Press button under ID. (Note: A 10 second delay will default to ID.)
• To start locating the ID, select Yes. (To not locate the ID, select No.)
• The transmitter will begin by transmitting on ID 0 (zero). If the pager received the page, at the
prompt [receive] select Yes. If not, select No. The transmitter will automatically increment to
the next ID and page. Repeat this step until the pager receives the page.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Three Digit POCSAG Paging
If using the T9100 in an LRS system with Group Programmed POCSAG Pagers, the Group Paging mode
will allow the T9100 to page the three digit individual pager number of the POCSAG Pager.
When this mode is turned on, numbers on the keypad and display are treated as +100. (ex: Pressing 22, the
LED Display will show 22, pager #122 will be paged.)
Note: Turning on this mode will not enable support to page Group Numbers 1-99. The trans-
mitter will only page individual numbers 100-199.
To turn on Group Paging Support:
- Press PROG – PROG – 2 – 0 – ENT
- Press the button under Yes
- If done, select Yes (Button under Yes), if not select No (Button under No)
Long Range Systems 16 T9100 User Manual
Pager Programming
Star and Alpha Pagers can be reprogrammed from the T9100 transmitter. If the pagers need to have their
identification code reprogrammed, contact LRS before proceeding. The following is the basic procedure to
use:
For Server Pagers:
1. Be sure to set the T9100 for the System ID in use.
2. Be sure the POCSAG (FM) start is correct for the pagers in use.
3. Reset the pager:
• Rechargeable pagers are removed from the charger (or touched to the reset terminals. They
stop vibrating when reset is complete.)
• Battery powered pagers reset when turned off and then back on (or remove and replace battery).
4. Press PROG- # - ENT (# is the pager number 1 through 99).
5. After the pager responds, page it to ensure it programmed okay.
• Star pagers will do one glow mode cycle.
• Alpha pagers will beep 4 times.
For Manager Pagers:
1. Be sure to set the T9100 for the System ID in use.
2. Be sure the POCSAG (FM) start is correct for the pagers in use.
Long Range Systems 17 T9100 User Manual
T9100 CANCEL PANEL
1
2
3
4
5
6
7
8
9
1
0
M1
M
2
8
6
C
L
R
P
R
O
G
E
N
T
V
1
V
2
V
3
www.pager.net
0
CANCEL PANEL
Overview of T9100 Cancel Panel
Antenna
Cancel Keys
Power
Supply
Reset Terminals
Function Keys
Number Keys
Vibration Keys
Keypad
Function Keys
The function keys are located along the bottom row of the Cancel Panel.
- M1 & M2 used to page and program Manager Pagers.
- 86 “All Call” button used to page all pagers.
- CLR used to clear an entry or to back up one menu level.
- PROG press once to program pagers, press a second time to access the menu functions.
- ENT used to enter functions.
Vibration Keys
V1, V2 and V3 select the number of vibrations a pager will respond with. This button is pressed before paging a pager. Sends message 1, 2 or 3 to Alpha pagers.
Cancel Keys
The row of keys located below the display. These keys will cancel a call to the pager number shown on the
display immediately above the respective key. The Cancel Keys also are used during menu selection.
Long Range Systems 18 T9100 User Manual
Using the T9100 Cancel Panel
Paging
o page pagers 1 though 99 enter the 2 digit number of the pager.
T
The transmitter can page up to 16 pagers at one time without using the 86 “all call” button.
When paged, the pager number will show on Cancel Panel display. If not canceled, the pager number will
begin to flash after the first re-page time expires. The pager number will flash faster after the second re-page
time expires.
Cancel Page
To Cancel a page, press the Cancel Key immediately under the number of the pager.
If using a Cancel Panel with T9100, the pager number may be canceled from the Cancel Panel or by pressing CLR then the pager number on the T9100.
Long Range Systems 19 T9100 User Manual
User Preferences
The T9100 Cancel Panel operates as a “Slave” to the T9100. Many settings are transmitted to the Cancel Panel
via the T9100.
To edit preferences, refer to the User Preferences of the T9100. Note: To enter selections greater than 10, the
user will need to enter as two numbers. Example, enter 15 by pressing 1 and then 5.
Paging from Cancel Panel
This feature enables or disables the Cancel Panel from paging pagers. This feature is only available and
only set on the Cancel Panel. The default setting is On to page pagers. To disable:
• Press PROG – PROG – 1 – 7.
• At [CP Paging] press the cancel button under OFF.
• If done, select Yes (button under Yes), if not, select No (button under No.)
To enable
• Press PROG – PROG – 1 – 7 – ENT.
• At [CP Paging] press the cancel button under ON.
• If done, select Yes (button under Yes), if not, select No (button under No.)
Long Range Systems 20 T9100 User Manual
Associating the T9100 Cancel Panel to T9100
1. Apply power to T9100 and allow it to boot up.
2. While T9100 is booting, apply power to the cancel panel and allow it to boot up.
3. The transmitter times should synchronize.
If a Canel Panel doesn not synchronize.
1. On T9100, press PROG – PROG – 2 - 9 - ENT to start Associate mode.
Note: The T9100 will stay in Associate for 2 minutes.
2. On Cancel Panel, press PROG – PROG – 2 – 9 – ENT to start Associate mode. When the Cancel
Panel associates, it will display:
• Attempt Join
• PAN Found
• Then display channel and Pan ID.
Changing Transmitters as 2.4 GHz Master
Any T9101, T9100, or T9100 can act as a single coordinater for the 2.4 GHz network, synchronizing most settings and clocks for all transmitters.
To Set a Transmitter as Master:
1. Press PROG-PROG-25 (T9101) or PROG-PROG-2-5 (T9100/CP).
2. Select YES.
3. The transmitter will now restart and display the time and date entry. Enter the time and date.
If another transmitter in the network does not successfully change from “Master” to “Slave” status on T9101:
1. Press PROG-30 to release from Network.
2. Press 7 for YES. Transmitter will restart and enter Associate Mode.
3. On “Master” of network Press PROG-PROG-29 (T9101) or PROG-PROG-2-9 (T9100/CP) to enter Associate Mode.
4. If T9101 does not initially associate, Press PROG-PROG-29 to enter Associate Mode.
Long Range Systems 21 T9100 User Manual
SERVICE QUESTIONS AND ANSWERS
Should your paging system ever fail or should you need additional paging supplies, call Long Range Systems
at (800) 437-4996.
Normal Business Hours
Monday – Friday 8:30 am to 5:00 pm Central Time.
Weekend or Night Emergencies:
• Long Range Systems has 24/7 live technical support available.
• Please keep in mind that replacement options are limited over the weekend.
Long Range Systems 22 T9100 User Manual
LRS PAGERS AVAILABLE FOR THE T9100
www.pager.net
(These pagers are sold separately)
SP5 Rechargeable Alpha
LRS Alpha E467
Star Rechargeable Pager
USING THE SP5
Select Button
Charging
Any rechargeable pager will require use of an LRS charger. The SP5 uses the Charger 5 (CH-R5)
1. Place the pager in the charger
2. Allow unit to charge fully overnight.
3. Remove from charger and the pager will vibrate or beep to show it is working.
4. The LCD will show the pager’s ID
5. Return the pager to the charger at the end of each day
Menus
To access the vibe/contrast menu, simply remove the pager from the charger or use the reset terminal on the
T9100. While it is vibrating or beeping, press and hold the Select Button for 8 seconds. The following top
level menu will display:
VIBE CONTRAST
. If you PRESS and RELEASE the Select Button, the menu selector will scroll to the right and will high-
light “Contrast
VIBE CONTRAST
To exit this menu wait 8 seconds
To re-enter the vibe/contrast menu at any time, reset the pager, and then hold the SP5 pager button.
Long Range Systems 23 T9100 User Manual
Vibe
To set the Vibration Level:
. Remove the pager from the charger
1
. While vibrating or beeping, press and hold the Select Button for 5-8 seconds
2
. Highlight the Vibe selection then PRESS and HOLD the Select Button until the screen shows.
3
VIBE
4. Press or hold the Select Button until the desired vibration level is selected
5. If holding down on the Select Button, the vibe level will increase to max and then decrease towards the minimum
6. Release the Select Button when desired vibration level has been reached
7. To exit, wait 8 seconds and the pager will go back to the vibe/contrast menu
Contrast
To set the Contrast Level
1. Remove the pager from the charger
2. While vibrating or beeping, press and hold the Select Button for 5-8 seconds
3. Highlight the Contrast selection then PRESS and HOLD the Select Button until the screen shows.
VIBE CONTRAST
CONTRAST:
4. Press or hold the Select Button until the desired contrast is selected
5. If holding down on the Select Button, the contrast level will increase to Max (NOTE: screen could
be dark and hard to read)
6. Release the Select Button and press or hold again to change the level back towards the minimum
or until your desired contrast is selected
7. To exit, wait 8 seconds and the pager will go back to the vibe/contrast menu
VIBE CONTRAST
8. To exit this menu wait 8 additional seconds
Long Range Systems 24 T9100 User Manual
Settings
To view the current pager settings
1. Remove pager from the charger or reset on the T9601, T9100, or T9101 reset terminals.
2. Press the Select Button repeatedly to scroll through the settings:
C1: [System ID number] and Pager ID number
C2: [System ID number] and All Page number
C3: [System ID number] and System ID number
G: Group number
Enc: Encryption enabled (128) or none
Ver: Current Firmware Version
3. To exit, wait 8 seconds.
Messages
The pager stores the last 5 received messages.
To view the messages:
1. At the (blank screen/time & date) menu display, press the Select Button once
2. Messages 2 lines in length will show a > symbol at the end of the first line and a < symbol at the beginning of the second line
3. Messages over 2 lines in length, the middle lines will show “< the next line of the message >”
4. Press the Select Button to continue scrolling forward through the message or messages
Time
Pager will display the current time. This feature is automatically updated by the T9100 transmitter. If the time
does not appear, a flashing star will appear on the right side of LCD to show pager is operational.
Reprogramming and Reset
To reset and reprogram the pager, see Pager Programming of this document.
Long Range Systems 25 T9100 User Manual
USING THE LRS ALPHA E467
www.pager.net
Menus
Read All
10/25 10:38am
SCROLL UP
SCROLL DOWN
SELECT/READ
BUTTON
SCROLL UP
SCROLL DOWN
Selecting functions
1. From Read All screen, press Up (or Down) Scroll button until desired selection displays
2. Press Read/Select button to select item
3. Press Up (or Down) Scroll button to choose/adjust
4. Press Read/Select to confirm/set
Power On/Off
Set ON (if unit is off)
1. Press and hold Scroll Up until YES/NO shows.
2. At “Power ON?” use Up (or Down) Scroll button to select YES
3. Press Read/Select button to set
Set OFF
1. Using the Up (or Dn) scroll button scroll until display shows “Power OFF?”
2. Press Read/Select button to set power on/off
3. At “Power OFF?” screen, use Up (or Down) Scroll button to select YES
4. Press Read/Select button to set
Long Range Systems 26 T9100 User Manual
Read Message
Appel Telephonique
• Messages are displayed upon receipt.
• Press Read/Select to display.
To review stored messages:
1. Select “Read All?”
2. Press Read/Select to display messages and time stamps
3. Use the Up (or Down) Scroll button to scroll through messages
Delete Messages
1. Using the Up (or Down) scroll button, scroll until display shows “Delete All?”
2. Press Read/Select
3. Use the Up (or Down) scroll button to select Yes or No
4. Press Read/Select button to confirm
Time/Date Set
1. Using the Up (or Down) scroll button scroll until display shows “Set Time/Date”
2. Press Read/Select to set time/date
3. Press Up (or Down) scroll button to set each time or date segment and press Read/Select to move
through the segments
[01/16]
10:04 AM
01/02/2008
SCROLL UP
SCROLL DOWN
Set Contrast
1. Using the Up (or Down) scroll button scroll until display shows “Set Contrast”
2. Press Read/Select
3. Use the Up (or Down) scroll button to adjust
4. Press Read/Select to confirm
Auto ON/OFF
1. Using the Up (or Down) scroll button scroll until display shows “Auto ON/OFF”
2. Press Read/Select to set auto on/off
3. Use the Up (or Down) scroll button to select On or Off
4. Press Up (or Down) scroll button to set on/off time and press Read/Select to move through the segments
Set Key Tone On/Off
1. Using the Up (or Down) scroll button scroll until display shows “Set Key Tone”
2. Press Read/Select to set key tone on/off
3. Use the Up (or Down) scroll button to select On or Off
4. Press Read/Select to set
Long Range Systems 27 T9100 User Manual
Select Alert
1. Using the Up (or Down) scroll button scroll until display shows “Set Alert Mode”
2. Use the Up (or Down) scroll button to select Beep/Vibe Off
3. Press Read/Select to set:
Beep - Use the Up (orDown) scroll button to select:
• Select Loud or Soft and press Read/Select to set
Select Duration (seconds) and press Read/Select to set
•
Vibe Off - Use the Up (or Down) scroll button to select
• Press Read/Select to set
Long Range Systems 28 T9100 User Manual
Using the Star Pager
1
2
3
4
8
00
.
4
3
7.
4
9
9
6
w
w
w
.
p
a
g
e
r
.
n
e
t
1
4
Charging
Any rechargeable pager will require use of an LRS charger. The Star Pager (SP4) uses the Charger 9 (CH-R9)
1. Place the pager in the charger
2. Allow unit to charge fully overnight (at least 24 hours)
3. Remove from charger, and pager will vibrate, beep, and light
4. Replace the pager in the charger at the end of each day
Messages
The pager can vibrate, beep, and light up message lights.
• Star pagers are intended to vibrate the number of times determined by the Vibe mode selected.
On the T9100 this is done by choosing the V1, V2 or V3 button. This can be a way to send additional information or to identify 1 of 3 stations.
• On the front of the pager are four lights 1 through 4. In normal operation each “station” or
T9100 would be set for different STATION ID’s (e.g. kitchen is station 1, etc.) Each station will
also send different messages (example 1st light for station 1, 2nd light for station 2, 4th and 1st
light for station 5, etc.). So if they were paged they can look down at the pager to see which station sent the message (which light was lit). As an option you can also send the message as a
V1 for a station one message, or V2 for station 2, or V3 for station 3. This will enable the person being paged to avoid having to look down to see the lights.
Long Range Systems 29 T9100 User Manual
Cleaning & Charging Instructions For LRS Paging Equipment
Cleaning:
LRS pagers are made from industrial-strength, polycarbonate material. However, this
material is susceptible to hairline cracking if non-approved cleaners are used. When cleaning LRS pagers, we recommend only using ISOPROPYL ALCOHOL-BASED CLEANERS.
To clean the equipment:
1. Take a clean rag and an isopropyl-alcohol based cleaner
2. Soak the clean rag with the isopropyl alcohol cleaner
3. Wipe down the pagers or equipment.
Cleaning equipment with any other non-approved cleaners can weaken plastic and
cause hairline cracks. Pagers and equipment that are cleaned with unapproved cleaners and suffer cracking will not be covered under warranty.
Do not submerge any LRS paging equipment in any type of liquid as this will also damage the equipment and is not covered under the standard warranty.
Charging:
Place rechargeable pagers on the charger and let them charge for 8 hours prior to first use.
Rechargeable pagers should be kept on charge even during extremely long periods of
inactivity.
Only 12 VDC power supplies should be used with LRS chargers and transmitters. DC
power supplies will cause damage to equipment that is not covered under the standard
warranty.
Should you have any questions, please contact the LRS Customer Service Department
at 800.437.4996.
Long Range Systems 30 T9100 User Manual
Warranty
Long Range Systems, LLC permits a one-year manufacturer’s warranty following the original consumer purchase date
of any LRS system. Any individual components or products purchased will receive a 30-day manufacture warranty. This
warranty covers any defects due to faulty material or workmanship, but does not include damage to the product resulting from accident, misuse or improper electrical connection. If the product or system should become defective within the
warranty period, we will repair or replace with equivalent equipment, free of charge. We will pay transportation charges
to return your product via standard FedEx Ground shipping, provided the product is shipped prepaid to:
Long Range Systems, LLC
4550 Excel Pkwy, Suite 200
Addison, TX 75001
No return or replacement can be received without prior authorization from the LRS Customer Support department or without the proper RMA# posted on the outside of the shipping container. Contact Customer Support at 800.437.4996 or
www.pager.net. This warranty gives you specific legal rights and you may also have rights that vary by state.
Copyright © 2013, Long Range Systems, Inc. All Rights Reserved
This manual contains proprietary information of Long Range Systems, Inc. (LRS) and is intended for use only by its employees or customers. None of the material contained herein may be copied, reproduced, republished, downloaded, displayed, posted, or transmitted in any form or by any means, including but not limited to, electronic, mechanical,
photocopying, recording, or otherwise without the prior written permission of LRS. Additional copies of this manual may
be obtained by contacting LRS.
Screen displays, keyboard layouts, hardware descriptions, or software are proprietary to LRS and are subject to copyright and other intellectual property rights of LRS and shall be treated in accordance with the previous paragraph.
All attempts have been made to make the information in this document complete and accurate. LRS is not responsible
for any direct or indirect damages or loss of business resulting from inaccuracies or omissions. Specifications and other
information contained within this document are subject to change without notice.
Long Range Systems, Inc. reserves the right to make changes without further notice to any products herein. LRS, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor
does LRS, Inc. assume any liability arising out of the application or use of any product or circuit, and specifically disclaims
any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be
provided in LRS, Inc. data sheets and/or specifications can and do vary in different applications and actual performance
may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. LRS, Inc. products are not designed, intended, or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the LRS, Inc. product could
create a situation where personal injury or death may occur. Should Buyer purchase or use LRS, Inc. products for any
such unintended or unauthorized application, Buyer shall indemnify and hold LRS, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that LRS, Inc. was negligent regarding the design or manufacture of the part, device or system.
EU DECLARATION OF CONFORMITY
We, Long Range Systems hereby declare under our sole responsibility that the T9100 and T9100CP paging transmitters
and on-site pagers comply with the essential requirements in the European RE&TTE Directive 1999/5/EC of the European
Parliament of the Council of 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity. The following standards were utilized:
ETS 300 224: 1998 EN 301 489-2: 2002
EN61000-3-2: 1998 EN 61000-3-3: 1995
EN 60950: 1992 with A1, A2, & A3
Long Range Systems 31 T9100 User Manual
XU-0039 053013
Loading...