Page 1
Job: ________________________
Item: _______________________
Hinged Lid Ice Cream Dispenser
CTAL-5
Shown with optional lid locking assembly
Quantity: ___________________
Models
length
❑ CTAL-5 50 3/8”
❑ CTAL-66 66 3/8”
❑ CTAL-7 74 3/8”
Benefits:
Large capacity of half pint
cartons
Durable and easy to clean
Standard Features
✔ 14 gauge stainless steel tops
✔ Insulated stainless steel hinged doors
✔ Molded fiberglass body
✔ Self-leveling dispensers
✔ 6 stainless steel trays per compartment
✔ Welded stainless steel interior
✔ 4” swivel casters
Optional Features (specify)
❑ (A) Tray slide, stainless, solid V ridge
❑ (B) Tray slide, stainless, flat surface
❑ (D) Cutting board, stainless
❑ (AA) Cam operated line-up locks
❑ (DD) Convenience outlet, flush mount
❑ (EE) Convenience outlet, pedistal mount
❑ (FF) End drop shelf, stainless
❑ (GG) Lid Locks
❑ (SS) Stainless steel legs
❑ (TT) Wrap-around bumper
❑ (**) Stainless or laminate body construction (specify)
❑ 5” swivel casters
❑ Optional height (specify ______________)
Tel: 770.478.8803 • Fax: 770.471.3715
www.lowtempind.com • colorpoint@lowtempind.com
Easy mobility
Cartons kept at easy-to-reach
height
Performance
These Heavy Duty, versatile units are designed to maintain proper holding temperatures with a forced air finned coil system.
They provide fast, efficient product access
through hinged, insulated stainless steel lids
that help maintain approved temperatures.
P.O. Box 795 • Jonesboro, GA 30237
24
Page 2
Hinged Lid Ice Cream Dispenser
”
2
/
1
1
30”
length
Plan View End View Elevation View
36”
”
4
/
1
5
Job: ____________________________
Item: ___________________________
Quantity: _______________________
Drain Valve
120V/1 phase
Capacity
Model Length Tray Size Top Opening using 3 oz cups Comp. Amps Plug Ship Weight
3
CTAL-5 50
CTAL-66 66
one - 20x20
CTAL-7 74
General Specifications
Body: Body to be seamless molded fiberglass (F.R.P.) with
/8” one - 20x20 1 692
one - 10x20
3
/8”
3
/8” two - 20x20 2 1344
2 992
smooth exterior surfaces and rounded corners. To be constructed
by a hand lay-up process with four layers of 1.5 oz continuous
strand fiberglass mat, plus a 24 oz layer of woven roving on
the bottom for added strength. Fiberglass to be flame retardant
per specification ASTM E-162 having a flame spread of 25 or
less. Body interior to be reinforced at each end with 4” wide, 12
gauge galvanized channels welded to form integral “U” frame for
maximum stress relief.
Top: Top to be 30” wide and fabricated from 14 ga. stainless
steel with square turndown on all sides and corners fully welded,
ground and polished. Top to have #4 satin finish and all edges
having #7 hi-lite finish.
Refrigerated Dispenser: Unit shall have a welded stainless
steel watertight interior liner with 2” of urethane foam insulation
and full perimeter breaker strips at the top. 1” brass drain shall
extend to a shut off valve below the fiberglass body. An interior
box temperature of -10 degrees shall be maintained by a finned
tube forced air coil with accessible thermostatic expansion valve,
and shall include an installed condensate evaporator. Openings
will be fitted high impact plastic throat liner and hinged insulated
stainless steel lids.
Each opening to contain a stainless steel self-leveling mecha
P.O. Box 795 • Jonesboro, GA 30237
Tel: 770.478.8803 • Fax: 770.471.3715
www.lowtempind.com • colorpoint@lowtempind.com
-
nism enclosed in a stainless steel housing, and shall be field
adjustable without the use of tools. Dispenser shall support the
product with a heavy gauge stainless steel frames and will include
six (6) stainless removable divider trays.
Compressor Housing: Cross flow ventilated compartment to
have two stainless steel exterior frames complete with removable
stainless steel louvers.
Condensing Unit: Unit to contain a fully hermetic system using
R-507 refrigerant, with all necessary controls for proper operation.
System to be hooked-up, tested in the factory and made ready to
plug in on the job.
Casters: 4” diameter, ball bearing, swivel type casters to be
non-marking and with brakes on all wheels. Casters are mounted
with exterior and interior bracing for maximum stress relief.
We reserve the right to change specifications and product design without notice. Such revisions
do not entitle the buyer to corresponding changes, improvements, additions or replacement for
previously purchased equipment.
All equipment to be built in accordance with the Underwriters Laboratories. Inc. and the National
Sanitation Foundation, Inc. standards and shall bear the Underwriters Laboratories, Inc. listing
label for safety and the Underwriters Laboratories classification label for sanitation.
1
/2 H.P. 16 5-20P 500 lbs.
1
/2 H.P. 16 5-20P 550 lbs.
1
/2 H.P. 16 5-20P 600 lbs.
03/2007
U.L. SanitationClassified to NSF Standards
Loading...