Lowell LWTR-3SB Specifications
Model No.
LWTR-3S
• Tilt-out wall rack, surface-mount
Wall-mount rack stores equipment vertically; front panel tilts down for equipment activation or servicing. Ideal for mounting ampliers, small mixers, PA
systems and consumer electronics in schools, training facilities or retail outlets.
Features
Spec No. 1596 [REV. 02.21.17] Page 1/2
Exterior decorator style cutouts
for quick access to optional
low-voltage devices without
opening the rack. Blank covers
conceal unused positions.
Center key lock
Slots on frame provide 3/4”
front-rear exibility when
screwing frame to backbox
to allow some adjustment for
uneven wall surface.
Adjustable-height
brackets help secure
non-rackmount gear
• Installation: Installs in brick, concrete block or stud wall construction. Proj-
ects 5.81” from wall surface.
• Construction: Steel construction and hinges provide solid support when
opened to 90 degree position. Neutral Network Grey wrinkle powder epoxy
nish. Beveled edges. Main compartment tilts down 15 degrees for equipment operation and 90 degrees for servicing. Note: Some equipment may
need to be horizontal to operate correctly.
• Measurements:
— Overall: 29.125”W x 29.125”H x 5.81”D
— Backbox: 29.125”W x 29.125”H x 4.00”D
— Frame: 29.06” x 29.06” x 1.81”D
— Accepts equipment up to 5.25”H x 17.5”D x 19”W
• Cutouts: Decorator style cutouts enable optional low-voltage devices to be
installed for easy exterior access (3) or secure interior access (2). Ideal for
volume controls, microphone connectors, phono jacks, or switches. Includes
blank cover plates (factory installed) for unused positions.
• Load Capacity: 50 lbs.
• Clamping Brackets: Two brackets (with adjustable height) help secure
non-rackmount consumer gear (equipment less than 19”W).
• Mounting Rails: One pair front-to-rear adjustable rails (7 positions), tapped
10-32
• Knockouts: 0.875” knockouts in top/base
• Vents: Front vents.
• Lock: Center key lock.
• E.O. box: Single gang EO box in base allows convenient connection to AC
power.
• Hardware: Pilot Point screws with captive washers
• EIA/TIA/RoHS compliant
Optional (order separately)
• Thumb Latch (TLK): Replaces key lock for key-less entry.
• Volume Control (100LVC-DW): 100W volume control with decorator style
plate, white. Additional models available online.
Adjustable mounting
rails tapped 10-32
Decorator style cutouts
on the interior provide
secure access to optional
low-voltage devices like
volume controls.
Rack includes factory-mounted
EO box in base
Closed view
Decorator style cutouts on the
exterior allow quick access to
optional low-voltage devices
without opening the rack.
Blank covers are included to
conceal unused positions.
A&E Specifications
The surface-mount wall rack with tilt-out operation shall be Lowell Model LWTR3S, which shall provide 3 rack units (5.25”) panel space for vertical mounting of
19”W equipment. Construction shall be steel with Network Grey wrinkle powder
epoxy nish. Overall measurements shall be 29.125”W x 29.125”H x 5.81”D.
The rack shall feature three exterior and two interior decorator style cutouts
with cover plates to mount optional devices (low voltage only). The rack shall
also feature front vents, center key lock, 0.875” knockouts in top/base, integral
handle, two brackets to help secure non-rackmount equipment, and one pair
mounting rails tapped 10-32 (front-to-rear adjustable in seven slotted positions). The assembly shall have a load capacity of 50 lbs. and include a single
gang EO box in the base.
Lowell makes every effort to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without notication.
©2017 Lowell Manufacturing Company, 100 Integram Dr., Pacic MO 63069 | 800.325.9660 | www.lowellmfg.com
Spec No. 1596 [REV. 02.21.17] Page 2/2
REAR VIEW
Model No. Summary
Model No. Description Rack Space Overall Width Overall Height Frame Depth Backbox Depth Wall Projection
LWTR-3S Tilt-out wall rack, surface-mount 3U (vertical) 29.125” 29.125” 1.81” 4.0” 5.81”
One rack unit (RU or U) = 1.75 inches or 44.45 mm. Some measurements may have been rounded.
Technical Drawings
Measurements are inches unless indicated otherwise.
5.81
5.81
TOP VIEW
BOTTOM VIEW
29.125 (BACKBOX)
29.06 (FRAME)
4.00
29.06
(FRAME)
29.125
(BACKBOX)
SIDE VIEW
18.314
FRONT VIEW
18.000
16.000
Lowell makes every effort to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without notication.
©2017 Lowell Manufacturing Company, 100 Integram Dr., Pacic MO 63069 | 800.325.9660 | www.lowellmfg.com
FRONT VIEW (OPEN)
Loading...