Lowell LPTR2-1019 Datasheet
Model: LPTR2-series
Lowell Pull & Turn Rack – 19"D(2 slides / 125 lbs. load)
escription:
D
The Pull & Turn Rack was designed for built-in wall and millwork applications and features a turntable on two heavy-duty slides for smooth pullout access to rackmounted equipment. The bottom base installs with
screws and can be mounted flush or recessed up to 2" in a boxed wall
or cabinetry to allow for equipment protrusions. The removable rack
base, with or without mounted equipment, docks and secures to the bottom base using two screws on the front and rear frame (no wing nuts
under the rack). When equipment is in place and wired, the assembly is
ecured in a fixed position with two screws through a perforated front se-
s
curity panel. The security panel can be removed to facilitate wiring and
servicing, allowing the rack to be pulled out from the wall or millwork. A
push button lock and release, accessible in the center front of the bottom
base, allows the rack to rotate 60º and 90º on the turntable. Note: the
rack must be fully forward to rotate with adequate clearance. If it is recessed up to 2" it will not rotate the full 90
0
.
The LPTR is engineered and packaged in two cartons for efficient onsite installation. The bottom base (with two slides and integral turntable)
along with two rear corner post rails and three cable lacing bars can be
sent ahead to the job site and installed in a boxed wall opening or cabinet.
The second carton contains the rack base, front and rear posts, side stiffeners, front vent panel and three lacing bars to assemble the rack for
pre-loading and testing of equipment in the shop — a real benefit for
boardroom and training facility installations.
Features:
• Made in the U.S.A. with 100% certified U.S. steel
• Base (14-ga. steel) with turntable and two heavy-duty slides
accommodate a load up to 125 lbs.
• Six corner-post rails tapped 10-32 (11-ga. steel)
• Two side stiffeners
• Six cable lacing bars
• Front security panel, perforated
• Black powder epoxy finish
Six cable lacing bars.
Two slides support a
load up to 125 lbs.
The LPTR2 ships unassembled
in two cartons.
Optional steel
top provides a
handy shelf.
Optional: (order separately)
• Top Cover (LPTR-TC): steel cover for top of rack. Black.
To Service Installed Rack:
1. Remove the bottom security panel (2 screws). If the security panel
is not used, the rack should be locked using two screws in the panel
location.
2. Pull the rack fully forward to clear the opening.
3. Locate the push button in the center of the base and depress it to
release the turntable, allowing it to rotate to 60
4. Depress the push button again to rotate the rack to the 90
Note: the 90
o
position is recommended when tying off cords and ca-
o
right or left.
o
position.
A & E Specifications:
The rack for built-in applications shall be Lowell Model ______. It shall
be 19.13"W and 19.22"D with 19" useable depth. Panel space shall be
________. The rack system shall include two heavy duty slides and a
turntable base allowing it to pull out and rotate 60
o
and 90o. The rack
shall be unassembled and ship in two cartons to facilitate job site installation of the bottom base and shop mounting and testing of equipment.
The rack system shall include cable management panels and be capable
of supporting a load up to 125 lbs. The rack shall be manufactured from
certified US steel and finished in smooth black powder epoxy.
[Rack shall also include a steel top (Model LPTR-TC).]
bles to rear lacing panels as it ensures adequate length at maximum
turn radius.
Model No. Description Rack Units* Overall D Useable D Panel Space Overall H Overall W
LPTR2-1019 Lowell Pull & Turn Rack – 2 slides 10 19.22" 19.00" 17.50" 20.08" 19.13"
LPTR2-1219 Lowell Pull & Turn Rack – 2 slides 12 19.22" 19.00" 21.00" 23.58" 19.13"
LPTR2-1619 Lowell Pull & Turn Rack – 2 slides 16 19.22" 19.00" 28.00" 30.58" 19.13"
LPTR2-2119 Lowell Pull & Turn Rack – 2 slides 21 19.22" 19.00" 36.75" 39.33" 19.13"
LPTR2-2419 Lowell Pull & Turn Rack – 2 slides 24 19.22" 19.00" 42.00" 44.58" 19.13"
LPTR-TC Steel Top
*One rack unit = 1.75"
Spec. No. 1035
(rev. 02.02.12)
pg. 1 of 2
©2012 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660
Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to
change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)
Model: LPTR2-series
13.97
19.22
19.13
3.0
11. 0
6.0
0.281 h
mo
18.13
12.13
16.00
1.41
0.261 hole if
mounting t
Lowell Pull & Turn Rack – 19"D(2 slides / 125 lbs. load)
Removable rack base allows shop wiring of equipment.
Both sections are shown
assembled with corner
posts and lacing panels.
Rack base
docks to the
bottom base.
Bottom base
has 2 slides
and turntable.
0oRotation
After docking,
secure the two
sections with screws
in front and rear.
Rack in 90oposition with cabling tied off.
o
60
Rotation
Six lacing panels are provided to guide cabling.
Perform wire tie off when
the rack is in 90
rotated position to ensure
adequate slack.
Dock and secure the rack
base to the bottom base
with screws on the front
and rear (no wing nuts
under the rack). When
equipment is in place and
wired, the assembly is
secured in a fixed position
with two screws through
the front of the bottom
base assembly.
o
90
Rotation
o
maximum
Security
panel
Bottom base installation
Spec. No. 1035
(rev. 02.02.12)
pg. 2 of 2
1.41
3.0
Push button
turntable release
0.261 hole if
16.00
18.13
12.13
6.0
11.0
19.13
©2012 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660
Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to
change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)
mounting to stud
0.281 holes for mounting
13.97
19.22
Overall H
19.13
19.00
Overall H
22
19.
All measurements are inches.
Loading...