Lowell ACSP-1502-RPC Specifications

Models: ACSP-1502-VTE, ACSP-1502-RPC

Compact 15A Surge Suppressor with cord

Description

This advanced surge suppressor provides the highest current ca­pacity available in devices of its size to protect multiple pieces of
sensitive electronic equipment on a single circuit. It features in­dustrial strength “zero failure” technology backed by a ten year
warranty. It also includes a patented* rotating outlet plate that
makes it easy to change the position of the outlets from top to side
access. The compact body has a very low profile (1.75"H x 6"D x
9"W) and includes two mounting brackets made for easy installa­tion — on a wall behind a flat panel TV, under a counter, in a rack
or just about anywhere. Both models have two 15A outlets and a
detachable cord.

• Model ACSP-1502-VTE: includes VTE over/under protec­tion (automatically turns outlets off when line voltage drops
below 100V or rises above 140V).

• Model ACSP-1502-RPC: includes remote power control ca­pability by a low voltage sequencer, switch or control system
that provides maintained dry contact closure.

ACSP-1502-RPC

Includes detachable
IEC cord with NEMA 5­15P plug and mounting
brackets.

ACSP-1502-VTE

*US Patent No. D535178S

Features

• ETL Listed, ANSI C62.41 Compliant

• Conforms to UL1449-3

• Low-profile chassis (1.75”H x 6”D x 9”W)

• Two 15A outlets spaced for power supplies

• Patented* plate rotates 90º for front or side access.

• Front LEDs provide visual system status.

• Suppresses line to neutral with no ground contamination.

• TCR technology defeats surges up to 72,000 amps with zero
failures

• Two mounting brackets allow versatile installation. (Optional
mounting ears are available if standard 19” panel installation
is preferred.)

• 6-ft. detachable IEC cord with NEMA 5-15P plug.

• 10 year warranty

A & E Specifications

The 15A single-circuit surge suppressor shall be Lowell model
__________ with two single outlets. It shall be ETL Listed and
conform to UL1449-3. It shall meet ANSI C62.41 and protect line
to neutral without ground wire contamination. It shall be capable
of protecting electronic equipment from transient voltages, spikes
and surges up to 72,000 amps and have a response time of less
than 5 nanoseconds. It shall surface or rear rackmount using
mounting brackets and include outlets mounted on a plate that
can be rotated 90º for front or side access. It shall include LEDs
for visual ground verification and surge diagnostics. [Model ACSP­1502-VTE shall also include automatic over/under voltage shut­down protection when voltage drops below 100V or rises above
140V. Model ACSP-1502-RPC shall also include remote power
control capability (by a low voltage sequencer, switch or control
system that provides a maintained dry contact closure).]

Optional mounting
ears (ACC-1ME) are
available if standard
19” rackmount instal­lation is preferred.

Mechanical Specifications:

Dimensions: 9"W x 1.75"H x 6"D
Weight: 5 lbs.
Input Connections: Detachable IEC cord with NEMA 5-15P plug
Output Connections: (2) single 15A receptacles mounted on 90˚

Chassis: Steel with black powder epoxy finish
Mounting: (2) mouning brackets

Performance Specifications:

Operating Voltage/Current: 120VAC / 15A, 60Hz
Maximum Surge Current: 72,000A (exceeds UL1449-3 6000V, 3000A)
Initial Clamping Voltage: 205V, UL rating 400V
Endurance: IEEE C62.41-1991, B3 (C1), Pulses (lifetime):

Transient Noise Reduction: 29dB@100kHz, 70dB@1MHz
Response Time: Less than 5 nanoseconds
Temperature Range: 25˚C (77˚F) nominal
Protection Mode: Line to neutral, zero ground leakage
UL1449-2 Adjunct Results: 1000 surges, 6000 volts, 3000A, C1, and B3

Federal GSA specs (1996) Grade A, Class 1, Mode 1
Diagnostic LEDs (surge)** Top (green): ON = ground verified

Applicable Standards: UL1449-3, IEEE standard 587-80 A & B, IEEE

Safety Agency Approvals: ETL Listed US and Canada.

**TCR surge suppression technology provides the assurance of Grade A, Class 1, Mode 1
endurance and performance testing plus visual diagnostic LEDs. The ground verified (green
LED), protection active (green LED) should always be ON and the reduced protection (red
LED) should be OFF. In the unlikely event the red LED illuminates, full suppression capability
is NOT immediately or even necessarily compromised. The red LED indicates the overall life
expectancy of the unit may be reduced. Contact Lowell for repair or replacement under the
unit’s ten year warranty.

rotatable plate.

1kv≥1,000,000; 3kv≥100,000; 6kv≥5000

waveforms (IEEE C62.41), NO FAILURES

Center (green): ON = protection active
Bottom (red): ON = protection reduced*

standard C62.41-1991, IEC 1000-4-5-1995
(IEC 801-5).

Model No. Description Outlets Amperage Termination Over/Under Protection Remote Control Capable

ACSP-1502-VTE Compact surge suppressor 2 15A detachable cord Yes No
ACSP-1502-RPC Compact surge suppressor 2 15A detachable cord No Yes
ACC-1ME Mounting Ears (1-pr)

Spec. No. 1c-113
(rev. 05.18.12)
pg. 1 of 2

©2012 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660
Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to
change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)

Front Panel Layout

ACSP-1502-VTE

Rotating Outlet Plate*

Remove the 4 screws holding the rotating
outlet plate (2 on front, 2 on top).

Installation Options with Mounting Brackets

ACSP-1502-RPC

Re-install the 4 screws.Pull the outlet plate away from the

chassis and rotate.

*US Patent No. D535178S

Surface-mount with
exposed brackets.

Control Options for ACSP-1502-RPC

Spec. No. 1c-113
(rev. 05.18.12)
pg. 2 of 2

©2012 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660
Fax—636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to
change specifications and/or improve manufacturing methods without notification. (lowellmfg.com)

Surface-mount with concealed
brackets (behind unit).

Mount to rack rail supports or
10-32 tapped rack rail.