Lowell ACS2024-2C User Manual

ACS1524-2C, ACS2024-2C Series

15/20A Hardwired Mutli-Circuit AC Power Strips - ETL Listed

Installation Instructions

Models Features Installation

Rack rail mounting channel

Alternating colors
indicate 2 separate
circuits

White

Gray

White

Gray

● Twenty-four receptacles, 12
per circuit (adjacent recepta­cles on opposite circuit).

● Symmetrical design, recepta­cles can be oriented “up” or
“down”.

● Power connections can be
made from either end, or both
ends for feed-through.

● Light colored receptacles for
high visibility inside cabinets,
alternating white and gray
colors indicate separate cir­cuits.

● Dimensions: 70"x1.625"x1.5".

● Long cable ties provided for
securing power supplies (see
detail).

Nut

Screw

Mounting

clip

1) Install mounting clip to rack

rail mounting channel using
hardware provided.

2) Align power strip with

mounting clips and snap
into place.

Easy installation into Lowell cabinets

and racks with adjustable mounting rails.

Z-bracket in rear of cabinet

Nut

Mounting

clip

Screw

ACS-1524-2C (15A) ACS-2024-2C (20A)

Model Specifications

ACS-1524-2C ACS-2024-2C

15 Amp 20 Amp

24 outlets 24 outlets

125 VAC 125 VAC

70"L 70"L

1.5"W 1.5"W

1.625"D 1.625"D

P/N 16099

pg 1 of 2

Printed in U.S.A. © 10-09-08

1) Install mounting clip to rack

Z-bracket using hardware
provided.

2) Align power strip with

mounting clips and snap
into place.

Easy installation into Lowell cabinets

with fixed mounting rails.

Lowell Manufacturing Company • 100 Integram Drive • Pacific, Missouri 63069 U.S.A.

Ca ll 800.325.9 660 , 636 .25 7.3 400 • Fa x 636 .257.660 6 • Cl ic k www. low ell mfg.c om



Remove cover



Connect wires



(Two possible wiring options)

Remove knock-out(s) as needed

ACS1524-2C, ACS2024-2C Series

15/20A Hardwired Mutli-Circuit AC Power Strips - ETL Listed

Pull out pigtails and
identify circuits



Circuit Two
(white recept.)

Wht

Receptacle
ground

Pull out pigtails, identify circuits.

NOTE: Factory installed push-in connectors suitable for SOLID wire ONLY. For stranded wire remove
and discard push-in connectors and use wire nuts or other suitable connectors (not included).

Blk

Green

Wht

Red

Chassis ground
(enclosure bonding)

Green

12-3 MC or equiv. with
appropriate connector

Connect all
grounds together

P/N 16099

pg 2 of 2

Printed in U.S.A. © 10-09-08

Multi-wire branch circuit (shared neutral)

Circuits must be on opposite phases to pre­vent neutral oveload.

Red

Chassis ground wire

Green

Blk

Lowell Manufacturing Company • 100 Integram Drive • Pacific, Missouri 63069 U.S.A. Cal l 800 .325. 966 0, 636. 257 .3400 • Fax [phone] • Click w ww.l owe llmfg .co m

Blk



Attach cover

Wht

Wht

connected to safety
ground

Tuck wires inside chassis and
re-install cover assembly

Independent circuits and isolated ground

12-3 MC or equiv. with
appropriate connector

Red

Wht

Wht

Green

Blk

Wht

Pigtails at opposite end can be
utilized as feed-through to
connect additional power strip.

Green w/yellow strips

Isolated ground
connected to

Green

receptacle ground
wire