Page 1
Set Password Ⅱ
For the password Ⅱ, enter ‘00’, then press the setting button, the buzzer "di di" will sound for twice, the
yellow indicator light on.
① Enter your passwordⅡ, and press "#"
② Repeat the password, then press "#" to confirm.
③ The green indicator light on indicates that the password setting is successful.
1. The "di di" sound indicating that the password has been set successfully, "di di di di di" sounds
Tip:
indicate that the user does not enter the same password, please repeat the procedures.
2. Please verity the passwords after done the passwords setting, and lock the door after verification.
Three ways to open the door
1. The first unlocking method: Use the emergency key
SAFE
OPEN
LOW.VOLT
INPUT
1 23
456
789
0 #
*
2. The second unlocking method:
SAFE
OPEN
LOW.VOLT
INPUT
1 23
456
789
0 #
*
Insert the emergency key into the keyhole, turn
it counterclockwise to the limit. Then turn the
knob to open the safe door(Suitable for
unlocking or for the first opening, forgetting the
password, or when the battery is dead)
Use the keyboard password.
After installing the battery，enter your password
and then press the "#" key, the green indicator
light on, then turn the knob to the right to open
the door.
Dual Alarm System
1. After 3 consecutive time wrong password, the safe will activate the alarm system, the alarm will sound
for one minute, then enter the correct password and the alarm will be canceled. If you want to turn off the
alarm immediately, you need to open the safe with the emergency key, and then remove the battery.
2. In standby state, press the "#" button, the "yellow" indicator light on, then a beep of long "di" sound, the
Vibration alarm mode is turned on. If the box is shaken or violent hit, it will give an alarm immediately, at
this point, enter the correct password to stop the alarm.
When power on, the system default for alarm is off.
When the door is opened, the alarm is turned off and needs to be turned on again.
Under-voltage warning
When the voltage is around 4.8V after opening the door, the red and green indicator lights will on at the same
time, reminding the user that the battery is low and needs to be replaced.
How to use the adjustable shelf
Turn the fastener clockwise and pull out the
fastener horizontally, you can adjust the
position of the shelf or take out the shelf
according to your needs.
How to install foot mat?
How to mount the safe?
Instruction Manual
SAFE BOX
SAFE
INPUT
LOW.VOLT
OPEN
1 23
456
789
0 #
*
3. The third unlocking method: Use the emergency battery box + password.
SAFE
LOW.VOLT
INPUT
1 23
456
789
0 #
*
OPEN
When the battery is too low to open the door,
insert 4AA batteries in the emergency battery box,
plug the emergency power cord into the emergen-
cy power jack on the right edge of the panel, then
OPEN
enter the correct password to open the door.
4
1. Remove the stickers of the four
foot mats
2. Install the four foot mats on the
bottom of the safe
1. Place the safe at the installation place. Mark the drilling spots on the wall
from the inside pre-drilled holes, then remove safe and drill the holes.
2. Put the expansion bolts into the drilled holes, take the expansion bolt out of
the sleeves, then place the safe and align the pre-drilled holes with drilled
holes, and insert the expansion bolts into its sleeves from inside of the safe.
Please do not lock the emergency key and emergency battery box into the cabinet.
5
Page 2
Component Description
Parts List
System Setting
Step1 Open the safe box for the first time
SAFE
INPUT
1 23
456
789
*
Inner cabinet
SAFE
OPEN
LOW.VOLT
INPUT
SAFE
INPUT
LOW.VOLT
Indicator light
LOW.VOLT
OPEN
Password button
0 #
(#:Confirming button)
1 23
456
789
0 #
*
OPEN
Emergency power jack
Instruction Manual
SAFE BOX
SAFE
LOW.VOLT
INPUT
OPEN
123
456
789
0#
*
Please do not lock the emergency key and emergency battery box into the cabinet.
Quick start guide*1
OPEN
Emergency battery box*1
Foot mat*4
1 23
456
789
0 #
*
SAFE
LOW.VOLT
INPUT
1 23
456
789
0 #
*
Left slide the keyhole cover to expose the emergency keyhole,
OPEN
insert the emergency key, and turn it counterclockwise to the
limit, turn the knob clockwise to open the door successfully for
the first time.
Step2 Insert the battery
Emergency keyhole cover
Knob
Safe box *1
Expansion screws*6
Emergency key*2
Inner cabinet key*2
Remove the internal battery case cover and install 4 AA 1.5 Volt alkaline batteries, the system will
power on. (Note: Rechargeable battery is not recommended as it may destroy the internal electronic
components of the safe).
Step3 Set the digital password
Internal battery case
Warnings
Locking bolts
Key hook
1. Do not lock the emergency key or emergency battery box into the cabinet.
2. The initial password are "1234" and "123456", both need to be modified.
Setting button
LED light
Fastener
Shelf
Document folder
1
3. lf the safe box is not used for a long time, the battery should be removed to
prevent leakage of liquid from damaging the electronic system.
4. Purchase 4 AA batteries in advance, this safe does not contain batteries.
5. This safe contains a memory chip, the password saved will not be lost, you
don't need reset after power off.
2
Note: 1. The user can set two independent passwords for the safe.
2. The initial password are "1234" and "123456", both need to be modified.
3. The password consists of a minimum 1 number and maximum 8 numbers.
4. 20 seconds after pressing a key, the safe will go to sleep state if there is no follow-up action.
SAFE
OPEN
LOW.VOLT
INPUT
1 23
456
789
0 #
*
Set Password Ⅰ
To set the passwordⅠ, the door must be opened first, then press the setting button on the inner side
of the door. Buzzer "di di" will sound for twice, then the yellow indicator light will on.(In daily use, the
yellow light will flash during password entry.)
① Then enter your passwordⅠ, and press "#".
② Repeat the password, then press "#" to confirm.
③ The green indicator light on indicates that the password setting is successful.
3
Loading...