Louvolite Roller Duo Roll Fitting And Operating Instructions

Roller Duo Roll

Fitting and Operating Instructions

Roller Duo Roll

Fitting and Operating Instructions

Carefully unwrap the roller blind and its associated brackets.

The end brackets are universal and can be xed in a top, face or side x position.
The intermediate brackets can be either top or face x only.

Note – Duo link tting can only be used on system 40 and 45.

FITTING THE BRACKETS

Secure a control end bracket on the right hand side of the blind. Measure from
this bracket to a point the same distance as the width of blind number 1 and mark
the position.

Secure an intermediate bracket at this point ensuring the outside face of the
intermediate bracket lines up with the marked position.

Now measure and mark the distance from this intermediate bracket to the end
bracket on the left hand side of the blind and secure a control end bracket.

FITTING THE BLIND

NOTE: The right hand side blind must be tted rst.

With the fabric rolled around the tube insert the male idle end plug on the right
hand blind through the intermediate bracket. With this in place offer the control
end to the control end bracket and secure the blind in place ensuring the centre
lug has dropped into the bracket.

With the fabric wrapped around the tube on the left hand side blind, insert the

female idle end of the left hand side blind into the male idle end plug of the right
hand side blind. With this in place offer the control end of the left hand side blind
to the control end bracket and secure the blind in place ensuring the centre lug
has dropped into the bracket.

Roller Duo Roll

Fitting and Operating Instructions

CHILD SAFETY

®

Your blind will be supplied with either Easybreak

connectors attached to the

operating chain or a cord tidy that will need to be tted to the wall.

Easybreak® System

®

Two Easybreak

connectors are connected to the operating chain 200mm apart.
This ensures that at least one of them will be in the vertical position ensuring they
perform as required.

If excessive weight is applied within the loop an Easybreak® connector will break

apart.

If an Easybreak® connector comes apart then it will need to be re-connected.
To re-connect, check the Easybreak® connector for damage. If undamaged,
re-connect the chain by inserting the last ball on the end of the chain into the larger
hole of the connector and push it into place.

Easybreak® Connector

200mm apart

Tensioned System using cord tidy.

If the blind is tted with a continuous loop chain then a cord tidy will be attached
to the chain. This must be tted to the wall as follows:

Fitting a side x cord tidy.

The cord tidy is a two piece device and will arrive with a disposable red tab tted

to it.

Roller Duo Roll

Fitting and Operating Instructions

Cord tidy

Disposable red tab

Remove the disposable red tab by disengaging it from the chain and then pull
out the disposable red tab.

Disposable retaining thrust washer

Disposable red tab

Position the cord tidy to the wall at the furthest distance below the roller tube
adding appropriate tension to the chain and mark its location.

Roller Duo Roll

Fitting and Operating Instructions

Split the cord tidy and mark the remaining offset hole position
before drilling and plugging both location holes if necessary.

Screw into the offset hole to x the back piece of the cord tidy to the wall.

Re-assemble the cord tidy with the chain and x it in previously marked position

with a screw through the centre hole.

Roller Duo Roll

Fitting and Operating Instructions

Push t a cover cap over the screw hole opening.

Cover cap

Roller Duo Roll

Fitting and Operating Instructions

Fitting a face x cord tidy.

Position the face x cord tidy to the wall at the furthest distance below the

headrail adding appropriate tension to the chain and mark its location.

Mark the remaining hole position before drilling and plugging both location holes
if necessary.

Roller Duo Roll

Fitting and Operating Instructions

Attach the cord cover plate with the screw provided.

Push t a cover cap over the screw hole opening.

Cover cap x 3

Roller Duo Roll

Fitting and Operating Instructions

OPERATING THE BLIND.

For a conventional roller blind, in order to lower the blind, pull the rearmost length

of chain downwards with a smooth and steady pressure. To roll the blind up do the
same on the front length of chain.

For a reverse roll blind the opposite is true, to lower use the front chain and to raise,

use the rear chain.

NOTE TO INSTALLER:

Please ensure a general child safety warning tag is tted on the product.

Notes

Floor

Tensioned System with Cord Tidy

Child Safety - BS EN 13120 Guidelines for Roller Blinds

1

If xing height is unknown

Blind drop

size

Roller Blind

1

Chain

length

- Blind drop ≤ 2.5 metres, the
chain length must be ≤ 1 metre.

- Blind drop > 2.5 metres, the

chain length must be drop of

blind minus 1.5 metres.

Fixing height

Floor

Breakaway Connector System

Roller Blind

Blind drop

size

Fixing height

Cord tidy

3

2

Distance between

chain & floor

1

max 2/3

blind drop

Distance between

chain & floor

3

Chain with 2 x
Easybreak connectors
spaced 200mm apart

2

2

If xing height known

All blind drop sizes, distance
between oor and bottom of chain
must be greater than 1.5 metres.

3

Cord tidy

Afx a cord tidy to the wall at
the maximum distance possible

from the blind control mechanism
ensuring all operating cords are

taut (chain no more than 50mm
apart at entry/exit of cord tidy).

1

If xing height unknown

- Blind drop ≤ 2.5 metres, the chain
length must be max 2/3 blind drop.

- Blind drop > 2.5 metres, the chain
length must be max 2/3 blind drop.

2

If xing height known

All blind drop sizes, distance
between oor and bottom of chain

must be greater than 0.6 metres.

3

Chain must be tted with 2 x
Easybreak connectors 200mm apart

Will break apart when excessive
force is exerted on the chain.

NOTE TO INSTALLER: Please ensure general child safety warning tag is tted on the product.

WARNING

Young children can be strangled by loops in pull cords, chains, tapes and inner cords that operate the product.

To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become
wrapped around a child’s neck. Move beds, cots and furniture away from window covering cords.

S224902 02342 5/17

Do not tie cords together. Make sure cords do not twist and create a loop.

Louvolite Customer Services Tel: [phone] Email: [e-mail]

Visit the Louvolite website to view the links to all of our assembly instructional videos

www.louvolite.com

Also find us on: