®
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
/ www.louroe.comtechsupport@louroe.com
INSTALLATION AND OPERATING INSTRUCTIONS
VERIFACT EGC
AUDIO MONITORING SYSTEM
DESCRIPTION
The Verifact E-AGC is an omni-directional, low
®
impedance, electret condenser microphone with built-in
preamp and automatic gain control. It can pick up
normal sounds approximately 25 ft. away, or within a 50
ft. diameter circle. It’s built-in limiter prevents the output
signal to be overdriven thus minimizing distortion.
Verifact E-AGC produces line level output (0 dB) and
®
can be located up to 1,000’ from the Louroe base
station. The gain of the microphone can be adjusted
through a potentiometer up to +10dB. The microphone
preamp is mounted inside a singe gang Bell Box
housing that is designed for outdoor use or in moist
environment. The Verifact E-AGC is compatible with
®
all Louroe Audio Base Stations or Louroe Audio
Interface Adapters.
®
VERIFACT EGC
FRONT
®
BACK
R
U
T
E
D
C
A
I
F
U
N
A
M
N
T
H
E
SPECIFICATIONS
Microphone Sensitivity
Frequency response
Output
Current drain
Supply voltage 12 Vdc
Output gain
Microphone housing
Dimensions
Weight
Weight
LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.
Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.
This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .
This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation
instructions provided by LOUROE ELECTRONICS.
Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.
®
-45dB
50 Hz to 8 kHz
Line Level (0 dB, 1kW at 1 Khz )
10 mA
+10dB
Standard single gang Bell Box
4 1/2” H x 2 3/4” W x 2 3/16” D
11.5 oz
1 lb
WARRANTY
®
®
IMPORTANT NOTICE
When this equipment is used as part of an
audio monitoring system, the law requires
that the public be given notice of AUDIO
MONITORING ON THE PREMISES. A
deca l noti ce is included with each
microphone shipped.
Federal Law References:
Federal Regulations, US Code, Title 18.
Crime and Criminal Procedure, Sec 2510.
®
®
®
AUDIO
MONITORING
On
These Premises
®
LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
PAGE 1 OF 4
(818)
Egc_mic-inst_12/14
INSTALLATION AND OPERATING INSTRUCTIONS
MECHANICAL INSTALLATION
Verifact EGC microphone Is designed for surface mounting to a wall or a pole. It should be located 6 to 8 ft. from
the area of desired coverage. One inch threaded knock-outs are located at the top and back side of the Bell Box
for conduit connection. As a finished unit, the Verifact E-AGC microphone is classified as Weather Resistant .
Sealing around faceplate and conduit connection is required. Make certain that when Verifact EGC assembly is
mounted, the microphone portion is facing downwards.
®
®
®
MICROPHONE CONNECTION
A 3-pin header is located on the back of the microphone housing, marked A, B, C.
A represents +12 Vdc Power
B represents Audio Output
C represents Ground
If using West Penn 452 or equivalent with same color code, starting from
right to left of the pluggable connector, connect as follows: (See
connections on right)
1. Red wire (12 Vdc) connects to terminal A or right hand most
terminal of the pluggable connector.
2. Black wire (audio out) connects to terminal B or middle terminal
of the pluggable connector
3. Bare wire (ground) connects to terminal C or left hand most of
the pluggable connector.
4. After all 3 wires are tightened in place on the pluggable
connector, plug it in to the 3 pin header located on the
pcboard. See interconnection diagram on next page.
CONNECTING VERIFACT EGC MICROPHONE TO A LOUROE BASE STATION OR AUDIO
®
INTERFACE ADAPTER
All Louroe audio base stations and Interface Adapters have corresponding terminal blocks marked A, B, C.
Connect other end of cable as follows:
1. Red wire from microphone connects to pin A of Base Station (12Vdc)
2. Black wire from microphone connects to pin B of Base Station (Audio Output)
3. Bare wire from microphone connects to pin C of Base Station (Ground)
CONNECTING VERIFACT™ E-AGC MICROPHONE TO OTHER AUDIO DEVICES.
If a Louroe audio base station is not used and microphone is being connected directly to another receiver from
other manufacturers, 12 Vdc power must be applied to terminals A and C. (A is positive, C is negative).
Terminals B and C of microphone (C is common) go to the “Audio In” or “Line in” of the audio source. We
recommend shielded cable connections for terminal B and C (See last page for interconnection diagram)
INSTALLATION TIP: If area to be monitored for audio is noisy or has background disturbances, the
microphone should be positioned close to the subject (4’ - 8’) if possible. Also, the microphone output can be
lowered by adjusting the gain control potentiometer. Rotating clockwise will increase the gain;
counterclockwise decreases the gain. The factory setting is 0dB output.
LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
®
website: www.louroe.com e-mail: sales@louroe.com
Page 2 of 4
(818)
Egc_mic-inst_12/14
INSTALLATION AND OPERATING INSTRUCTIONS
WIRING REQUIREMENTS
2 Conductor shielded cable, 22
gauge with a 24 gauge drain
wire.
NOTE: Unshielded cable is not
satisfactory for audio
systems.
TO LOUROE BASE STATION, AUDIO INTERFACE
OR OTHER RECEIVING DEVICES
PLUGGABLE HEADER
PLUGGABLE CONNECTOR
MICROPHONE GAIN ADJUSTMENT
The microphone has an audio output
gain potentiometer. Microphone is
always shipped with a 0dB output. If
it’s necessary to change the gain of
the microphone, insert a small
screwdriver into the potentiometer
rotate clockwise to increase or
counterclockwise to decrease.
Maximum gain is +10dB
A
B
C
MIC ELEMENT
LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
®
(818)
website: www.louroe.com e-mail: sales@louroe.com
Page 3 of 4
Egc_mic-inst_12/14
INSTALLATION AND OPERATING INSTRUCTIONS
CONNECTING A LOUROE MICROPHONE DIRECTLY
TO AN IP CAMERA, ENCODER OR DVR WITH 3.5mm
MONO AUDIO INPUT
CONNECTS TO MIC HEADER ON THE PC BOARD
MICROPHONE PLUGGABLE CONNECTOR
COMMON GROUND
12VDC POWER SUPPLY
Black Wire
S
T
E
R
E
O
3.5mm Stereo CONNECTION
3.5MM MONO PLUG
OTHER PLUGS WIRING CONFIGURATION
Red Wire
Black Wire
R
C
A
Audio In
of receiver
Audio In
of receiver
RCA CONNECTION
Red Wire
LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
®
website: www.louroe.com e-mail: sales@louroe.com
Page 4 of 4
(818)
Egc_mic-inst_12/14
Loading...