Lotus ILMAS10 Instruction Manual
ILMAS10
3
ILMAS10
2
CONTENTS
1. Features ___________________________________________________________ 3
2. Names of Components ______________________________________________ 6
3. Switching the Mode (Display Function) ______________________________ 10
4. Hand 0-Position Check and Correction _______________________________ 11
• 0-Position Check
• 0-Position Correction
5. Setting the Time and Date __________________________________________ 15
• Setting the Time
• Setting the Date
• When the Date is not in the Center of the Calendar Window
6. Using the Chronograph _____________________________________________ 22
7. Setting Local Time ________________________________________________25
8. Using the Alarm __________________________________________________ 27
9. All-Reset _________________________________________________________29
10. Precautionary Items and Usage Limitation _________________________ 31
11. Warranty and After-Sales Service __________________________________ 41
12. Specifications ____________________________________________________ 43
13. Please Direct Inquiries To __________________________________________ 45
This watch is an analog quartz watch equipped with multiple functions including an
auto calendar function that changes the date automatically, a daily alarm function
that can be set based on a 24-hour clock, and a chronograph function that allows
measurement of time in 1/20 second units up to 59 minutes, 59.95 seconds.
1. FEATURES
ILMAS10 ILMAS10
4
5
Warning (caution) symbol followed by instructions that should be followed or
precautions that should be observed
Important instructions that should be followed are classified with the following symbol.
Can or will cause minor or moderate injury or damage
Can cause serious injury or death
Injuries and damage that might be caused by using the watch improperly or neglecting
any of the instructions or precautions contained in this manual are classified
with the following symbols.
Thank you for your purchase of this Lotus watch. Before using this watch, read this
instruction manual carefully to ensure correct use. After reading this manual, store it in
a safe place for future reference.
This manual contains the following the instructions that should be strictly followed at all
times to prevent injury to yourself and other persons as well as damage to property.
Safety precautions (Instructions to be followed at all times)
WARNING
CAUTION
Name/Mode Time/Calendar Chronograph
1. Mode hand TME CHR
2. Function hand Stops at 0-position
Chronograph minutes
1/20th seconds
3. Date Displays date
Date display
(TME or L-T)
4. Hour hand Displays hours
Displays hours
(TME, L-T or ALM)
5. Minute hand Displays minutes
Displays minutes
(TME, L-T or ALM)
6. Second hand Displays seconds Chronograph seconds
7. 24·hour hand
24·hour time display in
coordination with hour hand
24-hour time display in
coordination with hour hand
Local Time Alarm
L-T ALM
Stops at 0-position Stops at 0-position
Displays date of local time Date display (TME or L-T)
Displays hours of local time Displays alarm hours
Displays minutes of local time Displays alarm minutes
Displays seconds Displays ON/OFF
24-hour local time display
incoordination with hour hand
24-hour alarm time display in
coordination with hour hand
ILMAS10 ILMAS10
6
7
2. NAMES OF COMPONENTS
Name
Crown Alarm
position
¡Time/Calendar Chronograph
8 Crown
Normal position Mode switching Mode switching
Position 1 Calendar correction
0-position check/correction
(function hand, date wheel)
Position 2 Time correction
0-position check/correction
(second hand, 24 hour hand, hour hand, minute hand)
Button (A)
Normal position Not used
Start/stop, reset
(pressing continuously for at least 2 seconds)
Position 1 Not used
Function hand and date weel
0-position correction
Position 2 Not used
Second hand 0-position
correction
Button (B)
Normal position Not used Recalls 1/20 seconds when stopped
Position 1 Month correction Not used
Position 2 Not used Not used
Local Time Alarm
Mode switching Mode switching
Local time display Alarm ON/OFF setting
Local time correction Alarm time correction
(including ON/OFF switching)
Not used
Alarm tone monitor
(pressing continuously for at least 2 seconds)
Not used
ON/OFF switching
Not used
ON/OFF switching
Not used
Not used
Not used
Not used
Not used
Not used
ILMAS10 ILMAS10
8
9
ILMAS10 ILMAS10
10
11
4. HAND 0-POSITION CHECK AND CORRECTION3. SWITCHING THE MODE (DISPLAY FUNCTION)
This watch is equipped with four modes consisting of time/calendar,
chronograph, local time and alarm. Since the mode changes when the
crown is turned, the current mode can be confirmed with the mode hand.
Before using this watch, check that the functions of the watch operate
properly by performing the following procedure.
0-Position: This refers to the base position of each hand that enables
the watch to function properly.
[0-Position Check]
1. Turn the crown to switch the watch to the chronograph [CHR] mode.
2. Pull the crown out to Position 1 to check the 0-position (function hand
and date wheel correction mode). Confirm that the 24 hour hand, hour
hand, minute hand, second hand and function hand rapidly advance to
the 0 position, and the date wheel displays “1”.
ILMAS10 ILMAS10
12
13
0 Positions of each Hand (Base Positions)
24 hour hand: 24:00
Hour hand, minute hand: 00:00
Second hand: 00 seconds
Function hand: 0 position (12:00 position)
Date wheel: 1st
Perform the “0-Position Correction” when
the hands and date wheel are not at the
positions indicated above.
1. Pull the crown out to Position 1 in the chronograph [CHR] mode to correct
the function hand and date wheel.
2. Click (turn) the crown to the left to align the date wheel.
The 12:00 position immediately after the date changes to the “1st” is the 0
position of the function hand. After correcting the date wheel to the “31st” by
turning the crown, press button (A) to finely correct the function hand so that the
function hand is aligned at the 0 position after the date wheel changes to the “1st”.
(1 ) Clicking the crown once causes the function hand to make four
revolutions and the date to be corrected by one day.
(2) Turning the crown rapidly (clicking continuously two or more times)
causes the function hand to advance continuously.
When stopping the function hand, click the crown once to the right or left. When
the function hand is not stopped manually, it stops automatically after advancing
31 days
0-Position Correction of Function Hand and Date Wheel
[0. Position Correction]
Loading...