Lotus H586 Operating And Installation Instructions

Operating and installation instructions

for Fire

Lotus H586

Version 1, 24 May 2016

Introduction

Congratulations on your new Lotus Fire.

We hope and believe that it will give you many hours of warmth. Before you
really start enjoying your investment, please read these instructions thoroughly.
They provide important advice to ensure you derive great enjoyment from your
fire, both now and in the future.

First produced in 1979, Lotus wood-burning stoves boast a long history. The
stoves are manufactured in Langeskov on Funen and exported to many
European countries. So congratulations once again on your new Lotus fire,
which is certain to mark the start of a new, cosy life for you.

Installing the fire

Before installing and igniting the new fire, ensure that you take the time to read
these pages thoroughly.

Please ensure that all the necessary national and European standards and
regulations are complied with. Your Lotus dealer or your local chimney sweep
can provide you with the correct information.

Safety information

Burning wood releases thermal energy, which causes the surfaces, door, viewing
window, flue tubes and front panel of the stove to become very hot; please do not
touch these parts.
(Please use the enclosed heat-protection glove)

The plinth

Before installing the fire, ensure that your floor is capable of bearing the weight of
your fire. If this is not the case, you must take suitable measures to ensure the load­bearing capacity of your floor (e.g. a load distribution plate).

Flooring made of combustible materials must be protected by a non-combustible
covering around the opening of the fire. The non-combustible covering must extend
at least 50cm to the front and 30cm to each side of the opening of the fire.

Installation instructions

Model

Flue gas temperature at

nominal value °C

Measured in the

flue outlet

Performa

nce
kW

Flue gas

mass flow

g/s

Flue

extraction

Pa

Weight

kg

Distance from combustible materials

Free-standing

Behind

installation

Cm

Laterally to the

installation

Cm

H586

359

11

334

12

300 0 0

H486

The fire is ready to install and must be connected to your existing chimney with
a connector. The connector should be as short as possible, straight, horizontal or
slightly upwardly inclined. The connections should be sealed.

It must also be ensured that there is sufficient space to service the fire and clean
the connector.

It must be ensured that there is a sufficient air flow for combustion. This is
particularly important where there are tightly sealed windows and doors
(sealing lips). Air grilles should be positioned in such a way that they cannot
become blocked.

Replacement parts:

Only replacement parts expressly authorised or supplied by Lotus A/S may be
used. Where necessary, please contact your specialist dealer.

The fire must not be modified in any way!

The chimney dimensions should correspond to DIN 4705 T1, T2 or 13 13384-1,
or to the regulations pertaining in your country.

.

H586 was tested as an intermittent-burning fire.

The fire may be connected to multiple chimneys.

Chimney data from EN 13229 testing

The following instructions must be observed:

Distance from combustible building elements and furniture

Local and building regulations must be observed.
In case of doubt, please contact your local chimney sweep for advice.

Distance from non-combustible building elements and
furniture

There are no requirements relating to distance from non-combustible building
elements and furniture. (Defined in accordance with the relevant national
building regulations)

Installation in combustible construction materials protected by
insulation.

All mounted installations require ventilation.
The surround must provide openings for convection airflow.
Insufficient convection can result in damage to the surround/fire.
The illustration below shows the minimum permissible dimensions

to ensure sufficient
insulation/ventilation.

Convection air inlet: 400cm²
convection air outlet: 750cm²
Insulating material: any AGI Q132­approved insulation materials may be
used

.

Minimum permissible dimensions

Illustration of dimensions

H586 with carrying handle

Getting a fire started

Heating the fire for the first time will give rise to an unpleasant odour as the
protective paint dries. This will, however, be of short duration.

Use kindling with fire-lighter cubes to start up the fire. Suitable combustible
material may be added once the matchwood is alight.

Chimney/connection:

The chimney must be of the correct minimum length and diameter. It must be
carefully constructed to ensure that it is pressure-sealed throughout its length.
This is necessary to ensure the necessary updraught in the chimney required for
the correct functioning of the fire.

If these conditions cannot be met, please discuss other options with your
chimney sweep prior to installation.

Extractor hoods:

Extractor hoods, ventilation systems, etc. installed in the same room or
interconnected rooms as the fire can negatively impact on the fire’s functioning
(escape of smoke into living area) and must not be operated simultaneously
without suitable measures being undertaken.

Data for the chimney sweep:

Feed pressure:

Minimum feed pressure = 0.12 Pa.

Flue gas mass flow:

Exhaust gas mass flow = 10.1m(g/s).

Exhaust gas temperature:

The exhaust gas temperature is 334ºC.

Room ventilation:

Since a fire consumes oxygen, it must be ensured that oxygen is able to enter
the living areas, particular in the case of well-insulated homes. Always leave
the doors open between all rooms when the fire is in use. This ensures that the
fire receives more oxygen and also improves heat distribution.

Kindling

Kindling should be around 23-25 cm in length and 3-4 cm in diameter.

Wood

Various types of wood, including oak, beech, birch and ash are suitable fuels.
Impregnated wood, particle board, colour brochures and coated paper are not
suitable, as these all contain hydrochloric acid or heavy metals that cause
damage to both the fire and the environment. Under no circumstances may
waste materials or flammable liquids be used.

Split logs must be approximately 25-30 cm in length and 7-9 cm in diameter. A
maximum moisture content of 15-20% is very important for good combustion.
Excessively damp wood sharply reduces the performance of your fire, as a
significant proportion of the energy produced is required to vapourise the water.

Furthermore, due to its lower temperature, water vapour also has the
disadvantage of condensing in the flue tubes, which causes water droplets to
form. This can lead to undesirable consequences, such as severe corrosion and
the accumulation of soot. Wood that is too dry gasifies quickly, with the wood
burning too quickly compared to the available air supply. This results in
incomplete combustion, which has an environmental impact.

Storing wood

When buying wood, you should ensure that you have a sufficient quantity
stored for 1-2 years’ use. The wood needs to be in the form of split logs of the
right size and be stored under cover for a minimum of one year, depending on
the type of wood.

Nominal heat output

The fire’s nominal heat output is ? kW. This is attained at a minimum pressure
of 12 Pa. No more than three wooden logs should be placed in the fire at any
one time.

The fire is an intermittent-burning fire; please follow the instructions below to
ensure compliance with this specification.

Operating the fire
Lighting and loading wood

1. Place around 3 kg of dry, finely split wood in the centre of the combustion
chamber and arrange it in a pyramid shape. Light the wood with the help of two
fire-lighter cubes.

2. Leave the door open by around 2 cm for the first 8-10 minutes – under
supervision – and open the air valve fully (slide it all the way to the right).

3. If necessary, push the air valve in during the lighting process.

4. When the fire has burned down to embers (i.e. when there are no longer any
flames), carefully open the door so as not to disturb the ashes, and spread the
embers out into an even layer.

5. Place three equal-sized pieces of wood (approx. 2.6 kg) in the combustion
chamber. Two pieces should be placed on top of the embers parallel to the front

of the fire, approximately 1 cm apart. The front piece will ignite more easily if
one of the split sides is perpendicular to the window and another side is turned
towards the embers. The third piece should be laid parallel to the front piece.
The door should then be closed immediately.

6. Open the valve fully and slide it back only when the fire is burning nicely.
The degree to which the air valve needs to be open will depend on the draught
in the chimney. The aim is to ensure a vigorous fire with stable flames. If the
flames are upright and very calm, there is insufficient air (turbulence) and you
need to open up the air valve a little further.

7. Once the fire has again burned down to embers (no flames), repeat the
procedure as described from point 4, leaving the air valve fully open for the
first two minutes or so.

Ashes

Ashes can be disposed of with your household waste. Ensure that there are no
embers in the ashes that could ignite in your rubbish bin. The ashes should
therefore be left to cool for at least 1-2 days prior to disposal.

Cleaning the fire

The surfaces of all Lotus fires have been finished by the manufacturer with
original Senotherm paint in either “coke” or grey. The fires will emit an
unpleasant odour when they are first lit. Please ensure good ventilation.
Surfaces are best cleaned with a soft brush or a vacuum cleaner with a brush
attachment.
The combustion chamber, flue gas paths and flue tubes should be inspected
each year for deposits and, if necessary, cleaned, e.g. following the sweeping of
the chimney. When re-commissioning the chimney, please therefore ensure that
its full diameter is clear of any blockages.

Maintaining the fire

Seals may seem in good condition, but can collapse as a result of heat and lose
their ability to seal the fire. You should change them at least once a year if you
use the fire frequently. We recommend that they are regularly inspected by a
specialist.

It is easy to replace thermal components that are worn or disintegrating.

Baffle plates may also become worn down. They are easily replaced and can be
removed and re-inserted as described above.

Senotherm spray can be sprayed onto the fire to touch up stains. To preclude
the risk of fire, it is of the utmost importance that the fire is not in use (cold).
Larger defects must first be carefully rubbed down with fine steel wool and
surfaces must be free of dust and grease.

The spray can must be shaken vigorously and the fire coated from a distance of
15-20 cm

What is in the fire?

The fire contains installation and operating instructions, as well as heat­protection gloves to protect against burns.

Malfunctions

Should you experience problems with your Lotus fire, you may be able to find
out the cause below.

The fire is difficult to control – it is burning too fast

If your fire is new, please check that you are following the operating
instructions. If your fire is more than one year old or has been subjected to
heavy use, you may need to replace the seals. When the seals have been in use
for too long, they become flat and lose the ability to seal the fire effectively.

The fire has a poor draught since installation

Check that the installation instructions have been correctly followed. In
particular, there may be problems in connection with the chimney and
connector. If the diameter and length of the chimney are correct, is it properly
sealed and are the flue tubes and connections sealed? You may need to contact
your chimney sweep to resolve the problem, as there may be a blockage in the
chimney.

I can smell smoke and soot

This can be caused by wind blowing down the chimney and can occur when the
wind is coming from certain directions. The chimney might be too short, or
trees may have grown and be causing turbulence, or there might be an
insufficient supply of combustion air. If windows and doors are sealed, it may

be that there is no longer a sufficient supply of air, which can have an adverse
impact on the air flow in your heater. A possible solution would be an
additional supply of fresh air, e.g. by installing a ventilation flap near the
heating device or providing the fire with a direct supply of fresh air.
If an extractor hood is installed in the same room or interconnected rooms
sharing an air supply, it may negatively affect the function of your fire (and
cause it to emit smoke) when in operation and must therefore never be used
simultaneously.

Heating during periods of transitional weather/unfavourable
feed pressure

In periods of transitional weather, i.e. when outside temperatures are fluctuating
between hot and cold, sudden increases in temperature may lead to disturbances
in the air flow in your chimney, leading to the incomplete removal of the hot
gases. Where this is the case, the fire should be filled with lower amounts of
fuel and the primary air valve/controller opened to a higher setting, so that the
fuel is burned more rapidly (with visible flames), thus stabilising the chimney
draught.

What to do in the event of a soot fire in your chimney

If the wrong wood or overly damp wood is used, deposits may form in the
chimney, leading to a soot fire in the chimney. Close all the fire’s vents
immediately and inform the fire brigade. Once the fire in the chimney has burnt
out, have your chimney examined by a specialist to identify any cracks or leaks.

2. Lift the door handle,
which will allow you to
open the door outwards

How to clean the (internal) glass panel

1. Open the sealing mechanism

The baffle plates should also be regularly removed to allow the

1

2

removal of any soot deposits that can frequently accumulate here.

First remove the vermiculite and then the steel baffle plates.

WARRANTY CERTIFICATE

Lotus wood-burning stove – 10-year warranty

As from 1 September 2014, Lotus is now offering a 10-year warranty rather than the
previous five-year warranty. This warranty is applicable to all fires supplied by
Lotus after this date.

This warranty certificate is for the Lotus fire type _________, production number
_____________, purchased on ____________.

Claims under the warranty are valid only under normal operational conditions, i.e.
using normal split wood and compressed briquettes, and only if the wood-burning
stove has been operated in accordance with the instructions.

The warranty covers the correct functioning of the fire and does not cover damage
caused by overheating, damage to paintwork, parts subject to wear and tear and

moving parts such as glass, fireclay, stones, riddling grate, baffle plates, seals, slide

valves and the lock.

The warranty is invalid if the wood-burning stove is not operated in accordance with
the instructions, and if defects or the like are repaired by a person not authorised by
Lotus Heating Systems A/S, and in the event of attempted repairs by a person not
authorised by Lotus Heating Systems A/S. The warranty does not cover damage
caused by improper use.

If a product is returned to Lotus Heating Systems A/S and it transpires that the
damage is not covered by the warranty, the customer shall be liable for the ensuing
costs.

Any repair under warranty does not extend the warranty period for the repair, which
is in line with the original warranty period.

This warranty certificate shall only be valid if completed and accompanied by the
dealer's original invoice. The warranty period commences on the date of the invoice.

We hope you enjoy using your new Lotus wood-burning stove.

Yours sincerely Dealer:

Johnny Ebstrup Lotus Heating Systems A/S