Losi TEN-MT User guide

INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

EN

EN

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.
For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in dam-

age to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and
responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with
incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and mainte­nance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon
Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM

or Spektrum.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS AND WARNINGS

As the user of this product, you are solely responsible for operating in a manner that does not
endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside
your control. This interference can cause momentary loss of control, so it is advisable to
always keep a safe distance in all directions around your model as this margin will help avoid
collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor,

electronic speed control and battery, because they generate high temperatures. You may
burn yourself seriously touching them.

• Do not put fingers or any objects inside rotating and moving parts, as this may cause
damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car. Always turn off
the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio
equipment.

TABLE OF CONTENTS

CONTENTS ................................................................................................................. 2

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ......................... 3

QUICK START .............................................................................................................3

CHARGING THE BATTERY .........................................................................................3

INSTALLING THE BATTERY........................................................................................4

SPEKTRUM DX2E RADIO SYSTEM ...........................................................................4

SRS4201 AVC TECHNOLOGY RECEIVER ................................................................ 4

INSTALLING THE TRANSMITTER BATTERIES ...........................................................4

SRS4201 STABILITY ASSIST RECEIVER....................................................................5

DRIVING PRECAUTIONS ...........................................................................................5

POWERING ON THE VEHICLE ................................................................................... 5

BEFORE RUNNING YOUR VEHICLE ..........................................................................5

AVC SENSITIVITY ......................................................................................................5

DISABLING AVC.........................................................................................................6

PERFORMING A CONTROL DIRECTION TEST .......................................................... 6

RUN TIME...................................................................................................................6

CHANING THE TRAVEL ADJUST SETTINGS..............................................................6

DYNAMITE FUZE 130A SENSORLESS BRUSHLESS ESC (DYN4955) ......................6

DYNAMITE FUZE 3800KV BRUSHLESS MOTOR (DYNS1616) ................................8

TROUBLESHOOTING GUIDE .....................................................................................8

LIMITED WARRANTY ................................................................................................9

FCC INFORMATION ............................................................................................10

IC INFORMATION ...............................................................................................10

WARRANTY AND SERVICE CONTACT INFORMATION ..........................................10

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION................................10

REPLACEMENT PARTS ......................................................................................36–37

OPTIONAL PARTS ....................................................................................................37

EXPLODED VIEWS .............................................................................................38–41

CONTENTS

REGISTER YOUR LOSI PRODUCT ONLINE

Register your vehicle now and be the first to find out about the latest option parts, product
updates and more. Click on the Support tab at WWW.LOSI.COM and follow the product
registration link to stay connected.

COMPONENTS

• Losi® TEN-MT RTR with AVC® technology: 1/10-Scale 4WD Monster Truck (LOS03006 T1/T2)

• Spektrum™ DX2E 2.4GHz Transmitter (SPM2330)

• Spektrum™ 4-Channel DSMR® AVC Surface Receiver (SPMSRS4201)

• Spektrum™ 9KG 23T Waterproof Servo (SPMS605)

• Dynamite® Fuze™ 130A Sensorless Brushless Waterproof ESC (DYN4955)

• Dynamite® Fuze™ 550 Brushless Motor 3800Kv (DYNS1616)

• 4 AA batteries (for transmitter)

2

2

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of
waterproof and water-resistant components to allow you to operate the product in many
“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your
vehicle should NOT be treated like a submarine. The various electronic components used in the
vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how­ever, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts
in the electrical cables, will be susceptible to corrosion if additional maintenance is not
performed after running in wet conditions. To maximize the long-term performance of your
vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose to run in wet
conditions. If you are not willing to perform the additional care and maintenance
required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and
complying with the following precautions could result in product malfunction
and/or void the warranty.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of
operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or
larger spur gear. This will increase torque (and motor life) when running in mud, deeper
puddles, or any wet conditions that will increase the load on the motor for an extended
period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the
body removed, place the vehicle upside down and pull full throttle for a few short bursts
until the water has been removed.

CAUTION: Always keep hands, fingers, tools and any loose or hanging objects

away from rotating parts when performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can
of compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a
garden hose. Avoid rinsing the bearings and transmission.

EN

EN

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you
have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before
use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the
manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water
is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certified
as water-resistant or waterproof. If the motor becomes excessively wet, apply very light
throttle until the water is mostly removed from the motor. Running a wet motor at high
speeds may rapidly damage the motor.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove
any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing
light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue
to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.

QUICK START

Please read the entire manual to gain a full understanding of the TEN-MT RTR vehicle, fine-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings
and instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline
or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to
initialize. Always power the transmitter ON before the vehicle and power it OFF
after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos
are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

CHARGING THE BATTERY

Choose a battery designed to work with the Dynamite® Fuze™ 130A Sensorless BL
Waterproof ESC. We recommend the Dynamite® 7.4 5000mAh 2S 30C LiPo: Hardcase
with EC3™ connector (DYN9005EC). Choose a charger designed to charge 2S Li-Po

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

batteries. We recommend the Dynamite® Prophet™ Sport Li-Po 35W AC Battery Charger
(DYNC2005CA). Refer to your battery and charger manuals for usage, safety, and charging
information.

3

3

EN

EN

INSTALLING THE BATTERY

1. Ensure the ESC is powered OFF

2. Turn the vehicle over.

3. Turn knob to release the battery door.

4. Install the fully charged battery in the vehicle.

5. Connect the battery to the ESC.

6. Close the battery door and twist the lock.

SPEKTRUM DX2E RADIO SYSTEM

7

6

5

8

9

4

3

10

2

7. Power ON the transmitter, then the vehicle.

IMPORTANT: Secure the ESC wires so they do not interfere
with the gearing.

1. Steering Wheel Controls direction (left/right) of the model

11

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. BIND Button Puts the transmitter into Bind Mode

4. ON/OFF Switch Turns the power ON/OFF for the transmitter

5. ST. REV Reverses the function of the steering when the wheel is turned left or right

6. Indicator Lights

- Solid green light—indicates adequate battery power

- Flashing green light—indicates the battery voltage is critically low. Replace batteries

7. TH. REV Reverses the function of the speed control when pulled back or pushed forward

8. ST Trim Adjusts the steering center point

9. TH Trim Adjusts the throttle neutral point

10. ST Rate Adjusts the sensitivity of AVC

11. Antenna Transmits the signal to the model

SRS4201 AVC TECHNOLOGY RECEIVER

12. BIND

13. DISABLE

1

14. AUX 2

15. AUX 1

16. THR

17. STR

12
13

14
15
16
17

INSTALLING THE TRANSMITTER BATTERIES

1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.

2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the
transmitter’s battery case.

3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
Charging non-rechargeable batteries may cause the batteries to burst, resulting

in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose
of used batteries according to national regulations.

For more information on the transmitter, go to www.horizonhobby.com and click
on the support tab for the Spektrum DX2E to download the instruction manual.

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

4

4

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

EN

EN

SRS4201 STABILITY ASSIST RECEIVER

AVC® – ACTIVE VEHICLE CONTROL™

The Spektrum SRS4201 receiver features Active Vehicle Control™ (AVC®) technology that
responds similar to traction control in full-scale vehicles. In addition to traction control, AVC
technology also increases steering stability during high speed driving or while driving over
rough terrain. As you increase the AVC sensitivity, the system increases steering stability and
traction control, similar to reducing the amount of steering rate in a computer transmitter.
Reducing the sensitivity value increases the amount of steering control from the transmitter.
The SRS4201 receiver also enables you to quickly turn AVC on or off if you participate
in organized racing.

IMPORTANT: You must use digital servos with the SRS4201 receiver. Do not use analog
servos as they willl reduce the performance of the system and may cause overheating.

CALIBRATING THE RECEIVER

1. With the vehicle on a flat, level surface, insert the Bind Plug in the BIND port on the
receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The orange LED flashes, indicating the receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Press and hold the BIND button while powering on the transmitter.

6. Release the BIND button when the orange LED slowly flashes. The transmitter and receiver
are linked when the orange LED is solid.

7. Pull the transmitter trigger to Full Throttle.

8. Push the transmitter trigger to Full Brake, then return the trigger to center.

9. Turn the transmitter steering wheel to Full Right.

10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.
The orange LED flashes once.

11. Remove the Bind Plug, then power off the receiver to save the settings.

12. Power off the transmitter.

FORWARD BRAKE/REVERSE

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power,
you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is
not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries dis­charged to a voltage lower than the lowest approved voltage may become dam-

aged, resulting in loss of performance and potential fire when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.
Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Remove the body from the vehicle.

4. Connect a fully charged battery pack to the ESC.

5. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless for at least 5
seconds.

6. Re-install the body on the vehicle.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement. All suspension arms and steering components
should move freely. Any binds will cause the vehicle to handle poorly.

Tip: To increase the ride height and ground clearance of your vehicle, install the included
shock spacers. The stock shock spacer measures 4mm. You can add one or both of the
medium (2 mm) and/or small (1 mm) spacers to increase vehicle height and ground
clearance.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or
charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim
so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

AVC® SENSITIVITY

The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the
sensitivity, the AVC® system becomes more sensitive to the vehicle drifting left or right. You
would use maximum sensitivity during high speed driving or drag racing, when you want
the vehicle to stay in a straight line. As the sensitivity value increases, the amount of
steering travel decreases.

Turn the ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the ST RATE knob clockwise to increase the sensitivity.
IMPORTANT: The ST RATE knob will only adjust the sensitivity when

the transmitter is bound to a DSMR® receiver. When the transmitter
is bound to a DSM®, DSM2® or DSM Marine receiver,
the ST RATE knob controls the steering dual rate.

5

5

EN

EN

EN

DISABLING AVC® TECHNOLOGY

If you participate in organized racing, you may be required to turn AVC off. To turn AVC off:

1. Insert a Bind Plug in the BIND port on the receiver.

2. Insert a second Bing Plug in the DISABLE port on the receiver.

3. Connect a fully charged battery pack to the ESC.

4. Power on the ESC. The orange LED flashes, indicating the receiver is in bind mode.

5. Center the ST TRIM and TH TRIM dials on the transmitter.

6. Press and hold the BIND button while powering on the transmitter.

7. Release the BIND button when the orange LED slowly flashes. The transmitter and receiver
are linked when the orange LED is solid.

8. Pull the transmitter trigger to Full Throttle.

9. Push the transmitter trigger to Full Brake, then return the trigger to center.

10. Turn the transmitter steering wheel to Full Right.

11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.
The orange LED flashes once.

12. Remove the Bind Plugs, then power off the receiver to save the settings. The receiver will
continuously blink to indicate AVC is disabled.

13. Power off the transmitter.

IMPORTANT: You must calibrate the receiver each time it is placed in bind mode. To activate
AVC, see the steps in "Calibrating the Receiver."

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating
increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.
The battery connectors may become hot during driving. Batteries will lose performance
and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries
and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airflow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the
vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move
forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.
When moving forward, the wheels should maintain a straight line without any steering wheel
input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to
turn the steering wheel.

CHANGING THE TRAVEL ADJUST SETTINGS

1. Hold the trigger in the full brake position and turn the steering wheel to Full Right while
powering on the transmitter. The LED flashes rapidly, indicating the programming mode is
active.

2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust
the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob
to adjust the full brake end point. Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left position. Turn
the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST
TRIM knob to adjust the right end point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.
The minimum Travel is 75%, and the Maximum travel is 150%.

IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate
the SRS4201.

DYNAMITE® FUZE™ 130A SENSORLESS BRUSHLESS ESC (DYN4955)

SPECIFICATIONS

Type Sensorless

Constant/Peak 130A/760A

Resistance 0.0004 Ohm

Function Forward/Brake–Forward/Brake Reverse

Operation Proportional forward, proportional reverse with braking delay

Input Voltage 7.4V–14.8V (The motor in this vehicle will not support 14.8V)

BEC Output 6V/3A

Overload Protection Thermal

Dimensions (LxWxH) 53.5mm x 36mm x 36mm

Weight 79 g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause
(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that
the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON.
If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause
(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

6

6

For sensorless brushless motors:

1. Connect the ESC terminal A (typically designated by a blue wire) to the motor’s terminal
A (red wire on a Dynamite® Fuze™ sensorless motor). This may also be changed in
Programming Item 12, Motor Rotation, without changing wire connections.

2. Connect the ESC terminal B (typically designated by a yellow wire) to the motor’s terminal
B (blue wire on a Dynamite® Fuze™ sensorless motor).

3. Connect the ESC terminal C (typically designated by an orange wire) to the motor’s
terminal C (black wire on a Dynamite® Fuze™ sensorless motor).

NOTICE: Always disconnect the battery from the ESC when you have finished operating
your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC
will continue to draw current when connected to the battery, resulting in possible dam­age to the battery through over discharge.

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is
neutral and the throttle travel range is at 100%. Disable any special functions such as
ABS, etc.

3. Press the SET button while powering ON the ESC. Release the button as soon as the red
LED starts to flash.

4. Calibrate the throttle points by pressing the SET button once after each step.

- Neutral (1 flash)—leave the throttle at rest, untouched

- Full throttle (2 flashes)—pull the throttle fully back

- Full brake/reverse (3 flashes)—push the throttle fully forward

5. The motor will run 3 seconds after the last step is completed.

Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside
motor wires. The center wire must remain in the center and cannot be moved to another
motor tab.

TEN-SCBE RTR, AVC: 1:10 4WD SCBE • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

EN

EN

ESC FUNCTIONS AND MODES

The ESC includes programming options so you can adjust the way your vehicle performs.
Refer to the included settings table to adjust the ESC for your driving conditions.

ESC PROGRAMMING PROCEDURE

Programming is accomplished using the SET button on the ON/OFF switch or Digital Program
Box (DYNS3005).

1. Connect a fully charged battery to the ESC.

2. Power ON the ESC using the ESC switch.

3. Hold the SET button for 1 second until the green LED blinks, then release the SET button
to enter programming mode.

PROGRAMMABLE ITEMS

Basic Items

1 Running Mode Forward w/ brake Forward/Reverse w/ brake Forward/Reverse

2 Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%

3 Low Voltage Cutoff non-protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

4 Start Mode Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9

PROGRAMMABLE ITEMS

Advanced Items

5 Max Brake Force 25% 50% 75% 100% disable

6 Max Reverse Force 25% 50% 75% 100%

7 Initial Brake Force = Drag Brake Force 0% 20% 40%

8 Neutral Range 6% (Narrow) 9% (Normal) 12% (Wide)

9 Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º

10 Reserved Item

11 Reserved Item

12 Motor Rotation Counterclockwise Clockwise

13 Li-Po Cells Auto Calculate 2 Cells 3 Cells 4 Cells 5 Cells 6 Cells

PROGRAMMABLE VALUE Default Settings
1 2 3 4 5 6 7 8 9

PROGRAMMABLE VALUE Default Settings
1 2 3 4 5 6 7 8 9

4. Press and release the SET button as needed to get to the desired menu option (the Green
LED will blink corresponding to the menu item number). Programming menu items 1
through 9 are accessible using the SET button on the ESC. Programming menu items 10 and
above are only accessible using the optional ESC programming card. Programming of menu
items 10 and 11 is only possible after firmware updates to the ESC programming card.

5. When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks.

6. Press the SET button to move among the settings based on how many times the red LED
blinks (Refer to the table for more information).

7. Save the setting by holding the SET button for 3 seconds.

8. Power OFF the ESC switch and repeat the instructions above to change other settings.

Tip: If desired, the ESC programming can be returned to default settings
by powering ON the ESC and holding the SET button for 5 seconds.

DESCRIPTIONS

1. Running Mode

- Forward Only with Brake
Intended for competition use, this mode allows only forward and brake controls.

- Forward/Reverse with Brake
This mode is the basic all-around mode, allowing forward, reverse and brake controls.
To engage reverse while moving forward, apply the brake until the vehicle has come to
a complete stop, release brake, then apply the brake again. While braking or in reverse,
engaging the throttle will result in the vehicle immediately accelerating forward.

2. Drag Brake Force

Adjusts the amount of brake automatically applied when the throttle is returned to the
neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing
improved turn-in and your vehicle’s general response to controls.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the
battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output
power shuts off and the red LED flashes twice repeatedly.

The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,
if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery
pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a

8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po
battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives
a very soft initial acceleration and level 4 gives a stronger initial acceleration.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking,
but can also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Initial Brake Force (minimum brake)

Adjusts the minimum amount of braking power when the brakes engage. The default
value is equal to the drag brake value. A high value can lock the wheels when the brake
is used.

8. Neutral Range

Adjusts the throttle sensitivity around the neutral point. A higher value results in the
throttle having to be moved more for the vehicle to move forward, backward or brake.

9. Timing

Adjusts the motor drive current timing. More timing gives more performance, but can
lower efficiency and cause damage to the motor and/or ESC by overload or overheating.

NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor
timing correctly can result in damage to the motor and ESC. Refer to the manufacturer
instructions for recommended timing settings.

The Following Programmable Items require the optional Digital ESC Program Box:

10. and 11. Available Items are subject to firmware updates to the ESC and the optional

digital program box.

12. Motor Rotation

Allows you to make this change in the ESC so no wires need to be changed between the
ESC and the motor.

13. Li-Po Cells

Allows the ESC to automatically detect or manually set the number of cells in your Li-Po
battery back.

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

7

7

EN

EN

EN

DYNAMITE® FUZE™ 3800KV BRUSHLESS MOTOR (DYNS1616)

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing for the stock platform. It offers an
ideal balance between speed, power and efficiency. Should you decide to customize your
vehicle with optional batteries or motors, it may be necessary for you to change the pinion or
spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater
torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with
fewer teeth will reduce torque and increase top speed. Care should be taken when installing
larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor
and ESC. When testing different gearing options, pay close attention to the temperature of
the motor and speed control to ensure you are operating within the temperature range of the
components. The motor or ESC should never be so hot that it cannot be touched. If tempera­tures are too hot, a different gearing combination with a lower pinion gear and/or higher spur
gear is suggested.

CHANGING THE PINION GEAR/GEAR RATIO

1. Unscrew the gear cover screw and remove the gear cover.

2. Loosen the motor screws and slide the motor back.

3. Place the new pinion on the end of the motor shaft so the set screw is located
over the flat on the shaft.

4. Position it so the teeth line up with the spur gear and secure the pinion by tightening
the set screw.

5. Set the gear mesh.

6. Reinstall the gear cover.

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting it is only necessary when changing
motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When
the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If
the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Unscrew the gear cover screw and remove the gear cover.

2. Loosen the motor screws and slide the motor back.

3. Put a small piece of paper between the pinion and spur gears.

4. Push the gears together while tightening the motor screws.

5. Remove the paper. Check the mesh at 3–5 different locations around
the spur gear for a small amount of movement.

6. Reinstall the gear cover.

NOTICE: For a 2S Li-Po battery, use the included 16T Pinion gear. For a 3S Li-Po battery,
use the optional 14T (Mod 1) pinion gear (LOSA3574).

NOTICE: If you use the 16T (Mod 1) pinion gear with a 3S Li-Po battery, damage to the
vehicle, ESC, and/or motor will occur.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels
do not rotate

Steering does not work Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

ESC gets hot Motor over-geared Use smaller pinion or larger spur gear

Poor run time and/or sluggish
acceleration

Poor range and/or glitching Transmitter batteries low Check and replace

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft flat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Servo gears or motor damaged Replace or repair servo

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

Driveline bound up Check wheels and transmission for binding

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

8

8

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

EN

EN

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased
(the “Product”) will be free from defects in materials and workmanship at the date of
purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due
to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable
technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon
will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be
defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability
of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon
has no control over use, setup, final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,
the user accepts all resulting liability. If you as the purchaser or user are not prepared to
accept the liability associated with the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Horizon reserves the right to change or modify this warranty at any time without
notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.
Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and
service you in the event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll
free telephone number referenced in the Warranty and Service Contact Information section to
speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live
and use the Product in, please use the Horizon Online Service Request submission process
found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.
An Online Service Request is available at http://www.horizonhobby.com/content/_service­center_render-service-center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting your product
for service. When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA number, a list of the included
items, and a brief summary of the problem. A copy of your original sales receipt must be
included for warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a
Li-Po battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole
discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notification. Service estimates are
available upon request. You must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you
will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for
service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of
use and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of
the un-serviced Product, through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant Product for a period of 60
days from notification, after which it will be discarded.

10/15

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

9

9

EN

EN

EN

Warranty and Service Contact Information

Country of Purchase Horizon Hobby Contact Information Address

United States of America Horizon Service Center

(Repairs and Repair Requests)
Horizon Product Support

(Product Technical Assistance)
Sales [e-mail]

United Kingdom Service/Parts/Sales:

Horizon Hobby Limited

Germany Horizon Technischer Service [e-mail]

Sales: Horizon Hobby GmbH

France Service/Parts/Sales:

Horizon Hobby SAS

servicecenter.horizonhobby.com/RequestForm/ 4105 Filedstone Rd.

[e-mail]
877-504-0233

800-338-4639
[e-mail]

[phone]

[phone]

[e-mail]
[phone]

Champaign, Illinois 61822 USA

Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom

Christian-Junge-Straße 1
25337 Elmshorn, Germany

11 Rue Georges Charpak
77127 Lieusaint, France

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.

CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the

equipment.

This product contains a radio transmitter with wireless technology which has been tested and
found to be compliant with the applicable regulations governing a radio transmitter in the

2.400GHz to 2.4835GHz frequency range.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product
is in compliance with the essential requirements and other relevant provisions of the

R&TTE and EMC Directive.
A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

Antenna Separation Distance

When operating your Spektrum
transmitter, please be sure to
maintain a separation distance of
at least 5 cm between your body
(excluding fingers, hands, wrists,
ankles and feet) and the antenna
to meet RF exposure safety re­quirements as determined by FCC
regulations.

The following illustrations show
the approximate 5 cm RF exposure
area and typical hand placement
when operating your Spektrum transmitter.

IC Information

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.

Instructions for disposal of WEEE by users in the
European Union

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a designated
collections point for the recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or where you
purchased the product.

10

10

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

IT

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part # English Deutsch Français Italiano

DYN4955 Fuze 130A Sensorless Bl WP ESC: 4WD SCT 1/8 Fuze 130A Sensorless Bl WP ESC: 4WD SCT 1/8 4WD SCT 1/8 - Contrôleur Brushless Fuze 130A Fuze 130A ESC BL senza sensori WP: 4WD SCT 1/8
DYNS1616 FUZE 550 BL Motor 3800kv FUZE 550 BL Motor 3800kv Moteur Brushless Fuze 550 3800Kv FUZE 550 motore BL 3800kV
LOS230018 Body Set, Painted: TEN MT BK/BLUE Karosserieset lackiert: TEN MT schwarz /blau TEN MT - Carrosserie peinte noire et bleue Set carrozzeria verniciata: TEN MT nero/blu
LOS230019 Body Set, Painted: TEN MT BLACK/GREEN Karosserieset lackiert: TEN MT schwarz /grün TEN MT - Carrosserie peinte noire et verte Set carrozzeria verniciata: TEN MT nero/verde
LOS231015 Front and Rear Shock Towers: TEN MT/SCBE Dämpferbrücke v/h: TEN MT/SCBE TEN MT/SCBE - Supports d'amortisseurs avant

et arrière
LOS231016 Chassis and Brace: TEN MT Chassis und Halter: TEN MT/SCBE TEN MT - Châssis et renfort Telaio e trapezio: TEN MT
LOS231017 Battery Box: TEN MT Akkubox: TEN MT TEN MT - Boitier batterie Scatola batteria: TEN MT
LOS231018 Body Post Set: TEN MT Karosseriehalterset: TEN MT TEN MT - Support de carrosserie Supporti carrozzeria: TEN MT
LOS231019 Radio Tray: TEN MT RC Halterset: TEN MT TEN MT - Platine radio Piastra radio: TEN MT
LOS231020 Wing Mount: TEN MT Flügelhalter: TEN MT TEN MT - Fixation d'aileron Supporto alettone: TEN MT
LOS232015 Wheel Hex w/Pins (4): TEN MT Radmitnehmer m. Stifte (4): TEN MT TEN MT - Hexagones de roues avec goupilles (4) Esagone ruota con perno: TEN MT
LOS232016 Center Diff Mount Set: TEN MT Mitteldiffhalter Set: TEN MT TEN MT - Support de différentiel central Set supporto diff. centrale: TEN MT
LOS232017 Center Dogbone (2): TEN MT Antriebsknochen mitte (2): TEN MT TEN MT - Cardan central (2) Cardano centrale (2): TEN MT
LOS232018 Axle Dogbone (2): TEN MT Antriebsknochen Achse (2): TEN MT TEN MT - Cardan de pont (2) Giunto cardanico (2): TEN MT
LOS233006 Front & Rear Shock Body: TEN MT Dämpfergehäuse: TEN MT TEN MT - Corps d'amortisseur avant et arrière Corpo ammortizzatore ant./post.: TEN MT
LOS233007 Rear Shock Shaft (2): TEN MT Stoßdämpferkolben Set hinten (2): TEN MT TEN MT - Tige d'amortisseur arrière (2) Stelo ammortizzatore posteriore (2): TEN MT
LOS233008 Front Shock Shaft (2): TEN MT Stoßdämpferkolben Set vorne (2): TEN MT TEN MT - Tige d'amortisseur avant (2) Stelo ammortizzatore anteriore (2): TEN MT
LOS233009 Shock Spacer Set: TEN MT Stoßdämpferdistanzstücke Set: TEN MT TEN MT - Entretoise d'amortisseur Set distanziale ammortizz.: TEN MT
LOS233010 Servo Arm Set: Ten MT Losi Servoarmset : Ten MT Ten MT - Set de palonnier de servo Set braccetto servocomando: Ten MT
LOS234010 Suspension Link Set: TEN MT Aufhängungsset: TEN MT TEN MT - Biellettes de suspension Set collegamenti sospensione: TEN MT
LOS235017 5-40 x 1 1/4" BH Screw (8) 5-40 x 1 1/4" BH Schrauben (8) Vis BHC 5-40 x 1 1/4" (8) 5-40 x 1 1/4" viti a testa tonda (8)
LOS235018 Set Screw, M3 X 3mm (10) Madenschraubenset, M3 x 3 (10) Set de vis, M3 x 3mm (10) Vite di arresto, M3 X 3mm (10)
LOS236000 E-Clips 2.5mm (12) E-Clips 2.5mm (12) E-Clips 2,5mm (12) E-clips 2,5mm (12)
LOS236001 3.2mm x 7mm x .5mm Washer (10) 3.2mm x 7mm x .5mm Unterlegscheiben (10) Rondelle 3,2mm x 7mm x 0,5mm (10) Rondella 3,2mm x 7mm x 0,5mm (10)
LOS43010 Wheel and Tire Mounted (2): TEN MT Felge mit Rad montiert (2): TEN MT TEN MT - Pneu et jante montés (2) Cerchione e gomma montati: TEN MT

LOSA3576 1.0 Module Pitch Pinion,16T: 8E,SCTE Losi Ritzel 16Z Modul 1: 8E 8E, SCTE - Pignon module 1.0, 16T Pignone 16T modulo 1.0: 8E,SCTE

LOSA6198 5-40 x 1 7/8" Buttonhead Screw (4) 5-40 x 1 7/8" Halbrundschrauben (4) Vis à tête bombée 5-40 x 1 7/8" (4) 5-40 x 1 7/8" viti a testa tonda (4)
LOSA6240 5-40 x 1/2 Caphead Screw (8) Losi 5-40 x 1/2 Zylinderkopfschrauben (8) Vis CHC 5-40 x 1/2 (8) 5-40 x 1/2 viti a testa a brugola (8)
LOSA6256 4-40 x 1/2 Button Head Cap Screw (6) Losi 4-40 x 1/2 Rundkopfschrauben (6) Vis tête bombée 4-40 x 1/2 (6) 4-40 x 1/2 viti a testa tonda (6)
LOSA6262 8-32 x 1/2" FH Screws (10) Losi 8-32 x 1/2 Flachkopfschrauben (10) Vis FH 8-32 x 1/2" (10) 8-32 x 1/2" viti a testa piatta (10)
LOSA6270 5-40 x 3/8" Flat Head Screws (10) Losi 5-40 x 3/8 Flachkopfschrauben (10) Vis tête plate 5-40 x 3/8" (10) 5-40 x 3/8" viti a testa piatta (10)
LOSA6271 5-40 x 1/2" FH Screws (10) Losi 5-40 x 1/2 Flachkopfschrauben (10) Vis FH 5-40 x 1/2" (10) 5-40 x 1/2" viti a testa piatta (10)
LOSA6272 5-40 x 3/4" FH Screws (10) Losi 5-40 x 3/4 Flachkopfschrauben (10) Vis FH 5-40 x 3/4" (10) 5-40 x 3/4" viti a testa piatta (10)
LOSA6274 5-40 x 1 7/8" FH Screws (2) Losi 5-40 x 1 7/8 Flachkopfschrauben (2) Vis FH 5-40 x 1 7/8" (2) 5-40 x 1 7/8" viti a testa piatta (2)
LOSA6275 5-40 X 5/8" Flat Head Screws (10) Losi 5-40 X 5/8 Flachkopfschrauben (10) Vis tête plate 5-40 X 5/8" (10) 5-40 X 5/8" viti a testa piatta (10)
LOSA6277 5-40 x 3/8" BH Screws (8) 5-40 x 3/8" Rundkopfschrauben (8) Vis BH 5-40 x 3/8" (8) 5-40 x 3/8" viti a testa tonda (8)
LOSA6278 5-40 x 1/2" BH Screws (8) Losi 5-40 x 1/2 Rundkopfschrauben (8) Vis BH 5-40 x 1/2 (8) 5-40 x 1/2" viti a testa tonda (8)
LOSA6279 40 x 3/4" BH Screws (8) Losi 5-40 x 3/4 Rundkopfschrauben (8) Vis BH 40 x 3/4" (8) 40 x 3/4" viti a testa tonda (8)
LOSA6280 5-40 x 1" BH Screws (4) Losi 5-40 x 1 Rundkopfschrauben (4) Vis BH 5-40 x 1" (4) 5-40 x 1" viti a testa tonda (4)
LOSA6282 5-40 x 7/8" BH Screws Losi 5-40 x 7/8 Rundkopfschrauben Vis BH 5-40 x 7/8" 5-40 x 7/8" viti a testa tonda
LOSA6286 5-40 x 5/8 BH Screws (8) Losi 5-40 x 5/8 RundkopfSchrauben (8) Vis BH 5-40 x 5/8 (8) 5-40 x 5/8 viti a testa tonda (8)
LOSA6290 8-32 x 1/2 BH Screws (8) Losi 8-32 x 1/2 Rundkopfschrauben (8) Vis BH 8-32 x 1/2 (8) 8-32 x 1/2 viti a testa tonda (8)
LOSA6302 5-40 Locking Nuts, Steel Losi Stoppmmuter 5-40 Stahl (4) Nylstop, acier 5-40 5-40 dado autobloccante, acciaio
LOSA6306 4-40 Aluminum Mini-Nuts (10) Losi 4-40 Aluminium Mini-Muttern (10) Mini écrous en aluminium 4-40 (10) 4-40 mini dadi alluminio (10)
LOSA6350 #4 and 1/8" Hardened Washers Losi Unterlegscheiben #4 und 1/8 gehärtet Rondelles durcies #4 et 1/8" #4 and 1/8" rondelle
LOSA6947 5x11x4 Rubber Sealed Ball Bearing (4) Losi 5x11x4 Kugellager gekapselt (4) Roulements étanches 5x11x4 (4) 5x11x4 cuscinetti a sfera sigillati in gomma (4)
LOSA6956 12 x 18 x 4mm Ball Bearing (2) 12 x 18 x 4mm Kugellager (2) Roulement à bille12 x 18 x 4mm (2) 12 x 18 x 4mm cuscinetto a sfera (2)
LOSA6957 10x15x4 mm BB (2) with Nylon Retainer 10x15x4 mm Kugellager (2) mit Bundrand Roulements 10x15x4 flasques nylon (2) 10x15x4 mm cuscinetti (2) con fermo in nylon
LOSA6958 6x12x4 mm BB (2) with Nylon Retainer 6 x 12 x 4 BB mm Kugellager (2) mit Bundrand Roulements 6x12x4 flasques nylon (2) 6x12x4 mm cuscinetti (2) con fermo in nylon
LOSB2021 Front Suspension Arm Set: 10-T Querlenkerset vorne: 10-T 10-T - Set de triangles avant Set braccetto sospensione anteriore: 10-T
LOSB2022 Rear Suspension Mount Cover: TEN-SCTE Querlenkerabdeckung hinten: TEN-SCTE TEN SCTE - Couvercle support suspension arrière Copertura supporto sospensione post.: TEN-SCTE
LOSB2023 Rear Suspension Arm Set: 10-T Querlenkerset hinten: 10T 10-T - Set de triangles Arr Set braccetto sospensione posteriore: 10-T
LOSB2100 Front Spindle & Carrier Set: 10-T Achsschenkel und Achsschenkelträger: 10-T 10-T - Set fusées et étriers avant Set fusello e portafusello anteriore: 10-T
LOSB2103 Rear Hub & Spacer Set: 10-T Hintere Aufhängung: 10-T 10-T - Fusées arrières et entretoises Set hub posteriore con rondelle: 10-T
LOSB2123 Steering Bellcrank Set: 10-T Servosaver Set: 10-T 10-T - Parties plastiques de sauve servo Set squadrette sterzo: 10-T
LOSB2124 Steering Posts/Tubes & Hardware: 10-T Stehbolzen für Servosaver: 10-T 10-T - Support, tubes et accessoires de direction Set comandi sterzo e hardware: 10-T
LOSB2211 Fr/R Pin Mount Cover Set: 10-T Abdeckung f. Querlenkerhalter: 10-T 10-T - Set de protections de supports de pivots Set copertura montante perno ant./post.: 10-T
LOSB2213 Pivot Pin Mount Set, Steel (4): 10-T Querlenkerhalter Set (4) Stahl: 10-T 10-T - Supports de pivots en acier Set montante perno girevole, acciaio: 10-T
LOSB2222 Front/Rear Sway Bar Kit: 10-T Querstabilisatorset v/h: 10-T 10-T - Barre antis roulis av./arr Kit barra antitorsione ant./post.: 10-T
LOSB2279 Steering Drag Link & Hardware: 10-T Lenkgestänge und Zubehör: 10-T 10-T - Barre d'ackerman et accessoires Rinvio trascinamento sterzo e hardware: 10-T
LOSB2904 Shock Plastics Set (4): 10-T Kunststoffteile Stoßdämpfer (4): 10-T 10-T - Set pièces plastiques d'amortisseurs (4) Set parti in plastica ammortizz. (4): 10-T
LOSB2905 Fr/R Shock Boots (8): 10-T Stoßdämpfermanschetten (8):10-T 10-T - Chaussettes de protection de tiges

d'amortisseurs (8)
LOSB2906 Shock Rebuild Set (2): 10-T Stoßdämpfer Reparatur Set (2):10-T 10-T - Kit de réparation d'amortisseur (2) Set riparazione ammortizz. (2): 10-T
LOSB2909 Piston Pack (2): TEN-T/TEN-SCTE Stoßdämpferkolben: TEN-SCTE TEN-T/TEN-SCTE - Pack de piston (2) Pistoni (2): TEN-T/TEN-SCTE
LOSB2963 Rear Racing Spring Set: TEN LOSI Rennfedernsatz hinten: TEN Set de ressorts arrière de compétition - TEN Set molle racing posteriori: TEN

Torrette ammortizz. ant./post.: TEN MT/SCBE

Protezione stelo ammortizzatore ant./post. (8): 10-T

36

36

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

LOSB3104 Front/Rear Gearbox Set: 10-T Diffgehäuse v/h Set: 10-T 10-T - Carter de transmission avant et arrière Set cellula ant./post.: 10-T
LOSB3436 40T Spur Gear, Mod 1: TEN-SCTE Zahnrad 40Z M1: TEN-SCTE TEN-SCTE - Couronne 40T, Mod 1 40T corona, Mod 1: TEN-SCTE
LOSB3553 Center Diff Outdrive Set (2): 10-T Diff Gehäuse u Dichtung Set : 10-T 10-T - Noix de cardan de diff central (2) Set trascinatore diff. centrale (2): 10-T
LOSB3563 Fr/R Diff Outdrive Set (2): 10-T Antriebswelle Vorne/hinten inkl. Zubehör: 10-T 10-T - Noix de cardan de sortie de diff avant et

arrière (2)

LOSB3564 Fr/R Driveshafts (2): 10-T Antriebswelle v/h (2): 10-T 10-T - Arbres de cardans av ou arr (2) Albero trasmissione ant./post. (2): 10-T
LOSB3565 Fr/R CV Couplers (4): 10-T CV Kuppungsstücke v/h: 10-T 10-T - Coupleurs de cardans avant ou arr CVD (4) Accoppiatori CV ant./post. (4): 10-T
LOSB3566 Fr/R Axles (2): 10-T Losi Achsen vorne / hinten (2): 10-T 10-T - Pont av./arr. (2) Assi ant./post. (2): 10-T
LOSB3568 Diff Gasket & Misc: 10-T Vergaserdichtung + div: 10-T 10-T - Set de joints et goupilles de diff Giunta diff. & hardware: 10-T
LOSB3569 Diff Gear Set w/Hardware: 10-T Zahnräderset Differential m Zbh.: 10-T 10-T - Pignons de différentiels avec accessoires Ingranaggio diff. & hardware: 10-T
LOSB3571 Fr Ring & Pinion Gear Set: 10-T Stirnrad vorne & Ritzelset: 10-T 10-T - Pignon conique d'attaque et couronne

conique avant

LOSB3572 Rear Ring & Pinion Gear Set: 10-T Stirnrad hinten & Ritzelset: 10-T 10-T - Pignon conique d'attaque et couronne

conique arrière

LOSB3590 Differential Gear Grease: TEN Differentialfett: TEN TEN -Graisse pour pignons de différentiel Grasso ingranaggio diff.: TEN
LOSB3591 Differential Screws (8): TEN Differentialschrauben (8): TEN TEN - Vis de différentiel (8) Viti differenziale (8): TEN
LOSB4022 Camber & Steering Ball Set (12): 10-T Kugelkopfset Lenkung & Spur (12): 10-T 10-T - Set de rotules de carrossage et direction (12) Camber & set sfere sterzo (12): 10-T
LOSB4109 Suspension Hinge & King Pin Set (10): 10-T Querlenkerstift (10): 10-T 10-T - Set d'axes de suspensions et d'axes de fusées (10) Braccetto sospensione & set king pin (10): 10-T
LOSB8154 Rear Wing & Hardware: 10-T 10-T Hinterer Flügel mit Zubehör Aileron arrière et visserie Alettone posteriore & hardware: 10-T

SPM2330 DX2E 2Ch DSMR Surface Radio w/SR310 DX2E 2Ch DSMR Surface Radio mit SR310 Émetteur DX2E 2 voies DSMR avec RX SR310 DX2E trasmittente DSMR a due canali con SR310
SPMSRS4201 Replacement Rx: SRS4201 DSMR AVC Ausstauschempfänger Rx: SRS4201 DSMR AVC Récepteur SRS4201 DSMR AVC de remplacement Ricevente di ricambio: SRS4201 DSMR AVC
TLR8202 Body Clips, Black (12): 22 Body Clips, schwarz (12): 22 22 - Clips de carrosserie noirs (12) Clip carrozzeria, neri (12): 22

TLR237000 5x8x2.5mm Bearings (2) 5x8x2.5mm Kugellager (2) Roulements 5x8x2,5mm (2) 5x8x2.5mm cuscinetti (2)

TLR245002 5-40 x 1/4" BH Screws (10) TLR 5-40 x 1/4'' BH Schrauben (10) Vis BH 5-40 x 1/4" (10) 5-40 x 1/4" viti a testa tonda (10)

TLR332001 HD Diff Housing, Integrated Insert: TEN TLR TEN : HD Diff Gehäuse TEN -Carter de différentiel renforcé, insert intégré Alloggiamento diff. HD, con inserti: TEN
TLR332051 Coupler Outdrive: SCTE 2.0 TLR Kupplungsstück für Antriebsklaue: SCTE 2.0 SCTE 2.0 - Noix de cardan Accoppiatore trascinatore: SCTE 2.0
TLR334000 O-Rings, Bleeder Shock Cap (8): TEN TLR O-Rings / Dämpferkappe mit Entlüftung (8): TEN TEN -Joints toriques de bouchons d'amortisseurs

à purge (8)

Set trascinatore diff. ant./post. (2): 10-T

Anello ant. & set pignoni: 10-T

Anello post. & set pignoni: 10-T

O-ring, tappo ammortizzatore con vite di spurgo
(8): TEN

IT

Optional Parts // Optionale Teile // Pièces Optionnelles // Parti Opzionali

Part # English Deutsch Français Italiano

DYNC2010CA Prophet Sport Plus 50W AC/DC Charger Dynamite Prophet Sport Plus 50W Gleich- und

LOS230017 Body Set, Clear: TEN MT Karosserieset transparent: TEN MT TEN MT - Carrosserie transparente Set carrozzeria trasparente: TEN MT
LOSB2130 Rear Hubs, Aluminum: TEN Losi Radträger hinten, Aluminium: TEN TEN - Fusées arrière en aluminium Mozzi posteriori, alluminio: TEN
LOSB2825 Front Shock Body (2): 10-T Dämpfergehäuse vorne: 10-T 10-T - Corps d'amortisseurs avant (2) Set corpo ammortizzatore ant. (2): 10-T
LOSB2826 Rear Shock Body (2): 10-T Dämpfergehäuse hinten: 10-T 10-T - Corps d'amortisseurs arrière (2) Set corpo ammortizzatore post. (2): 10-T
LOSB2845 Fr/R Shock Shaft Set (4): 10-T Stoßdämpferkolbenstange v/h (4): 10-T 10-T - Set de Tiges d'amortisseurs avant et arrière (4) Set stelo ammortizzatore ant./post. (4): 10-T
LOSB2959 Front Racing Spring Set: TEN Federnsatz Racing vorne: TEN TEN -Set de ressorts avant de compétition Set molle racing ant.: TEN
LOSB2963 Rear Racing Spring Set: TEN Federnsatz Racing hinten: TEN TEN -Set de ressorts arrière de compétition Set molle racing post.: TEN
LOSB3575 Front/Rear HD Lightened Outdrive Set (2): TEN Antriebsklauenset v/h HD extra leicht: (2): TEN TEN -Noix de cardans av/arr renforcées allégées (2) Set trascinatori ant./post. HD (2): TEN
LOSB3576 Center HD Lightened Outdrives (2): TEN Antriebsklauenset mitte HD extra leicht: (2): TEN TEN -Noix de cardans centrales renforcées

LOSB4003 Front/Rear Steering Turnbuckle Set (6): 10-T

(Requires LOSB4023)
LOSB4023 Rod End Set: 10-T (Requires LOSB4003) Losi Kugelpfannen Set (erfordert LOSB4003): 10-T 10-T - Set de Chapes (20) (nécessite LOSB4003) Set tiranti: 10-T (necessita LOSB4003)
LOSB4112 Adjustable Front Hinge Pin Holder Set: TEN Losi Querlenkerhalterset vorne einstellbar,

LOSB4113 Adjustable Rear Hinge Pin Holder Set: TEN Losi Querlenkerhalterset hinten einstellbar,

LOSB7013 320S Force Wheel, Chrome (2) Losi 320S Force Wheel/ Chrome (2) Jante 320S Force Chrome (2) 320S cerchione force, cromo (2)
SPMS601H Extra High Torque Servo Extra High Torque Servo Servo couple très élevé Servocomando extra high torque
TLR233020 Front Spring Set, Hard (3 pair): 22T/SCT, SCTE TLR Stoßdämpferfedernset vorne, hart (3 paar):

TLR234001 Carbon Front Tower: SCTE 2.0

(Requires LOS234009)
TLR234002 Carbon Rear Tower: SCTE 2.0

(Requires LOS234009)
TLR234039 Hinge Pin Set, TiCN (6): SCTE TLR Scharnierbolzen Set, TiCN (6): SCTE SCTE - Set d'axes de suspension Ti-Cn (6) Set perni braccetti, TiCN (6): SCTE
TLR234040 Front Shock Shaft, TiCN (2): SCTE TLR Kolbenstange vorne, TiCN (2): SCTE SCTE - Axes de triangles avant Ti-Cn (2) Stelo ammortizzatore ant., TiCN (2): SCTE
TLR234041 Rear Shock Shaft, TiCN (2): SCTE TLR Kolbenstange hinten, TiCN (2): SCTE SCTE - Axes de triangles arrière Ti-Cn (2) Stelo ammortizzatore post., TiCN (2): SCTE
TLR334017 Ft Spindle Carrier, 15 Deg, +2mm, Alum: SCTE TLR SCTE Radträger 15° + 2mm, Alu SCTE - Étrier porte fusée, 15°, +2mm en

TLR5062 Bleeder Shock Caps, Aluminum (2): TEN TLR TEN: Stoßdämpferendkappe Aluminium (2) TEN - Bouchons d'amortisseurs à purgeurs en

TLR99004 TLR Embroidered Cargo Bag TLR Tasche Sac de transport TLR brodé Borsone TLR
TLR99014 TLR Foam Pit Mat TLR Schraubermatte Schaum Tapis de stand en mousse TLR TLR Foam Pit Mat

Wechselstrom-Ladegerät

Gewindestifte Lenkung (6): 10T
(erfordert LOSB4023)

Aluminium: TEN

Aluminium: TEN

22 T/SCT, SCTE
TLR SCTE 2.0: Dämpferbrücke vorne Carbon

(erfordert LOS234009)
TLR SCTE 2.0 : Dämpferbrücke hinten Carbon

(erfordert LOS234009)

Chargeur Prophet Sport Plus 50W AC/DC Prophet Sport Plus 50W AC/DC caricabatteria

allégées (2)
10-T - Biellettes de direction avant et arrière (6)

(nécessite LOSB4023)

TEN - Support d’axes de suspension avant réglable Set piastrine regolabili anteriori: TEN

TEN - Support d’axes de suspension arrière réglable Set piastrine regolabili posteriori: TEN

22T/SCT, SCTE - Ressorts d'amortisseurs avant,
durs (3 paires)

SCTE 2.0 - Support d'amortisseurs avant en
carbone (nécessite LOS234009)

SCTE 2.0 - Support d'amortisseurs arrière en
carbone (nécessite LOS234009)

aluminium

aluminium (2)

Set trascinatori centrali HD (2): TEN

Set tiranti filettati ant./post.(6): 10-T
(necessita LOSB4023)

Set molle anteriori, dure (3 paia): 22T/SCT, SCTE

Torretta ant. in carbonio: SCTE 2.0
(necessita LOS234009)

Torretta post. in carbonio: SCTE 2.0
(necessita LOS234009)

Portafusello ant., 15°, +2mm, allu.: SCTE

Tappi ammortizzatore con vite di spurgo, allu.
(2): TEN

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

37

37

IT

TLR8202

LOSB8154

LOSA6278

LOS231020

LOSB8154

LOS231020

LOSA6278

LOS231020

Clear/Transparent/Transparente/Trasparente = LOS230017

Blue/Blau/Bleu/Blu = LOS230018

Green/Grün/Vert/Verde = LOS230019

Exploded View // Explosionszeichnung // Vue éclatée des pièces // Vista esplosa delle parti

38

38

TLR8202

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

CHASSIS EXPLODED VIEW

VUE ÉCLATÉE DU CHÂSSIS

VISTA ESPLOSA DEL TELAIO

CHASSIS EXPLOSIONSZEICHNUNG

IT

LOSA6262

LOS231017

LOS231016

LOS235017

LOS231016

LOS233010

LOSA6277

LOSB4022

LOSA6256

LOS232017

LOSA6256

LOSB4022

LOS234010

TLR237000

LOSA6350

LOSA6277

LOSB2124

DYN4955

LOSA6277

LOSB2123

LOSA6306

LOSA6350

LOSB2123

TLR237000

LOSA6275

LOSA6275

LOSB4022

LOSB4022

LOSB2123

LOSB2124

TLR237000

LOSB2124

LOSA6262

LOSA6270

LOSB2279

LOSA6350

LOSA6256

LOS231019

LOSA6350

SPMSRS4201

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

SPMS605

TLR8202

LOS231019

LOSA6270

39

39

IT

REAR EXPLODED VIEW

VUE ÉCLATÉE ARRIÈRE

DYNS1616

LOSB3553

HECK EXPLOSIONSZEICHNUNG

VISTA ESPLOSA DELLA PARTE POSTERIORE

LOS231018

LOSA6279

LOSB2906

LOSA6256

LOSA6279

LOS231015

TLR245002

LOS232016

LOSB2103

LOSA6240

LOSA3576

LOSA6958

TLR332001

LOS232015

LOSB3566

LOS232015

LOSB3570

LOSB3436

LOSA6956

LOSB3568

LOSB3569

TLR332001

LOSB3569

LOSB3569

TLR332001

TLR332001

LOSA6956

LOSB3568

LOS232016

LOSA6270

LOSB2906

LOSA6274

LOSB2022

LOSA6256

LOSB2906

LOSA6280

LOSB2213

LOSB3104

LOSA6256

LOSB2023

LOSA6280

LOSA6286

LOSA6302

LOSB2103

LOSB4109

LOSB4109

LOSA6302

LOSB4022

LOSB3564

LOSB3565

LOSB3563

LOS234010

LOSA6302

LOSA6282

LOSA6302

LOSA6957

LOSB4022

LOSB2904

REAR SHOCKS / STOSSDÄMPFER H

LOS233006

LOSB2906

LOS233009

LOSB2963

LOSB2904

LOSB2906

LOSB3553

LOS232017

LOSB2904

LOS233007

LOSB2904

LOSB2906

40

40

LOSB2213

LOSB2211

LOSA6271

AMORTISSEURS ARR / AMMORTIZZATORI POSTERIORE

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

LOSB2100

LOSB2904

LOSB2904

LOSB2963

LOS233007

LOSB2906

LOSB2904

LOS233009

LOS233006

LOSB2904

LOSB2906

LOSB2906

LOS232015

IT

LOSB3566

LOS43010

VUE ÉCLATÉE AVANT

FRONT EXPLODED VIEW

FRONT EXPLOSIONSZEICHNUNG

VISTA ESPLOSA DELLA PARTE ANTERIORE

LOSA6290

LOSB2021

LOSB3563

LOSB4109

LOSB3564

LOSB2021

LOSB2100

LOSB2100

LOSB3566

LOSA6957

LOSA6958

LOS232015

LOSB4109

LOS43010

LOSB2100

LOS43010

LOS43010

LOSA6272

LOSB4022

LOSA6290

LOSB4022

LOSA6302

LOS234010

LOSA6302

LOS234010

LOSB4022

LOSB2963

LOSA6286

LOSA6280

LOSA6282

LOSB2187

LOS233008

LOSB2904

LOS233006

LOSB2906

LOSB2904

LOSB2904

FRONT SHOCKS / STOSSDÄMPFER V

LOSB2906

LOS233009

AMORTISSEURS AVANT / AMMORTIZZATORI ANTERIORE

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

LOSA6256

LOS231015

LOSA6275

LOSB2211

LOSB2213

LOSA6256

LOSA6279

LOSA6947

TLR332051

LOSB3104

LOSA6956

LOSB3571

LOSB3568

LOSB3571

TLR332001

TLR332001

LOSB3568

LOSA6956

LOSB3569

LOSB4109

LOSB3104

LOSB4109

LOSB2213

LOSA6275

LOSB2211

LOSA6275

41

41

LOS231015

WWW.LOSI.COM

©2016 Horizon Hobby, LLC.
Losi, DSM, DSM2, DSMR, AVC, Active Vehicle Control, EC3, Dynamite, Fuze, Prophet and the Horizon Hobby logo are trademarks or
registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Patents pending.
Updated 09/16 49177.1 LOS03006 T1/T2