Losi Rock Rey User guide

Download

Page 1

1/10 RTR ROCK RACER

INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

Page 2

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in

damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM

or Spektrum.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS AND WARNINGS

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor,

electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.

• Do not put ﬁngers or any objects inside rotating and moving parts, as this may cause damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio equipment.

TABLE OF CONTENTS

CONTENTS ................................................................................................................. 2

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ......................... 3

QUICK START .............................................................................................................3

CHARGING THE BATTERY .........................................................................................3

INSTALLING THE BATTERY........................................................................................4

SPEKTRUM DX2E RADIO SYSTEM ...........................................................................4

SRS4220 AVC TECHNOLOGY RECEIVER ................................................................ 4

INSTALLING THE TRANSMITTER BATTERIES ...........................................................4

STABILITY ASSIST RECEIVER ....................................................................................5

DRIVING PRECAUTIONS ...........................................................................................5

POWERING ON THE VEHICLE ................................................................................... 5

BEFORE RUNNING YOUR VEHICLE ..........................................................................5

AVC SENSITIVITY ......................................................................................................5

DISABLING AVC TECHNOLOGY ................................................................................6

PERFORMING A CONTROL DIRECTION TEST .......................................................... 6

RUN TIME...................................................................................................................6

CHANING THE TRAVEL ADJUST SETTINGS..............................................................6

DYNAMITE FUZE 130A SENSORLESS BRUSHLESS ESC .........................................6

DYNAMITE FUZE 2800KV BRUSHLESS MOTOR ......................................................8

TROUBLESHOOTING GUIDE .....................................................................................8

LIMITED WARRANTY ................................................................................................9

WARRANTY AND SERVICE CONTACT INFORMATION ..........................................10

FCC STATEMENT ................................................................................................10

IC INFORMATION ...............................................................................................10

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION................................10

REPLACEMENT PARTS ......................................................................................35–36

OPTIONAL PARTS ....................................................................................................36

EXPLODED VIEWS .............................................................................................37–41

CONTENTS

Register your vehicle now and be the ﬁrst to ﬁnd out about the latest option parts, product updates and more. Click on the Support tab at WWW.LOSI.COM and follow the product registration link to stay connected.

COMPONENTS

• Losi® Rock Rey™ RTR: 1/10-Scale 4WD Rock Racer (LOS03009T1/T2)

• Spektrum™ DX2E 2.4GHz Transmitter (SPM2330)

• Spektrum™ 4-Channel AVC® Surface Receiver (SPMSRS4220)

• Spektrum™ 12KG 23T Waterproof Metal Gear Servo (SPMS612HV)

• Dynamite® Fuze™ 130A Sensorless Brushless Waterproof ESC (DYN4955)

• Dynamite® Fuze™ 550 Brushless Motor 2800Kv 6-Pole (DYNS1614)

• 4 AA batteries (for transmitter)

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 3

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction

and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certiﬁed as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

QUICK START

Please read the entire manual to gain a full understanding of the Losi® Rock Rey™, ﬁne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

CHARGING THE BATTERY

Choose a battery designed to work with the Dynamite® Fuze™ 130A Sensorless BL Waterproof ESC. We recommend the Dynamite® 7.4 5000mAh 2S 30C LiPo: Hardcase with EC3™ connector (DYN9005EC) or Dynamite 11.1 5000mAh 3S 50C LiPo Hardcase with EC3 connector

(DYNB3803EC). Choose a charger designed to charge 2S and/or 3S Li-Po batteries. We recommend the Dynamite® Prophet™ Sport Li-Po 35W AC Battery Charger (DYNC2005CA). Refer to your battery and charger manuals for usage, safety, and charging information.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 4

INSTALLING THE BATTERY

1. Ensure the ESC is powered OFF.

2. Slide the lever to the right to release the battery door.

3. Install the fully charged battery in the vehicle.

4. Connect the battery to the ESC.

5. Close the battery door and slide the battery door lever to the left to secure it.

6. Power ON the transmitter, then the vehicle.

SPEKTRUM DX2E RADIO SYSTEM

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. BIND Button Puts the transmitter into Bind Mode

4. ON/OFF Switch Turns the power ON/OFF for the transmitter

5. ST. REV Reverses the function of the steering when the wheel is turned left or right

6. Indicator Lights

- Solid green light—indicates adequate battery power

- Flashing green light—indicates the battery voltage is critically low. Replace batteries

7. TH. REV Reverses the function of the speed control when pulled back or pushed forward

8. ST Trim Adjusts the steering center point

9. TH Trim Adjusts the throttle neutral point

10. ST Rate Adjusts the sensitivity of AVC

11. Antenna Transmits the signal to the model

SRS4220 AVC TECHNOLOGY RECEIVER

12. BIND

13. DISABLE

14. AUX 2

15. AUX 1

16. THR

17. STR

12 13

14 15 16 17

INSTALLING THE TRANSMITTER BATTERIES

1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.

2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the transmitter’s battery case.

3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting

in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

For more information on the transmitter, go to www.horizonhobby.com and click on the support tab for the Spektrum DX2E to download the instruction manual.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 5

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

STABILITY ASSIST RECEIVER

AVC® – ACTIVE VEHICLE CONTROL

The Spektrum receiver features Active Vehicle Control™ (AVC®) technology that responds similar to traction control in full-scale vehicles. In addition to traction control, AVC technology also increases steering stability during high speed driving or while driving over rough terrain. As you increase the AVC sensitivity, the system increases steering stability and traction control, similar to reducing the amount of steering rate in a computer transmitter. Reducing the sensitivity value increases the amount of steering control from the transmitter. The receiver also enables you to quickly turn AVC on or off if you participate in organized racing.

IMPORTANT: You must use digital servos with the AVC receiver. Do not use analog servos as they willl reduce the performance of the system and may cause overheating.

™

CALIBRATING THE RECEIVER

1. With the vehicle on a ﬂat, level surface, insert the Bind Plug in the BIND port on the receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The orange LED ﬂashes, indicating the receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Press and hold the BIND button while powering on the transmitter.

6. Release the BIND button when the orange LED slowly ﬂashes. The transmitter and receiver are linked when the orange LED is solid.

7. Pull the transmitter trigger to Full Throttle.

8. Push the transmitter trigger to Full Brake, then return the trigger to center.

9. Turn the transmitter steering wheel to Full Right.

10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center. The orange LED ﬂashes once.

11. Remove the Bind Plug, then power off the receiver to save the settings.

12. Power off the transmitter.

FORWARD BRAKE/REVERSE

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power, you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged to a voltage lower than the lowest approved voltage may become dam-

aged, resulting in loss of performance and potential ﬁre when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck. Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Remove the body from the vehicle.

4. Connect a fully charged battery pack to the ESC.

5. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a ﬂat, level surface and motionless for at least 5 seconds.

6. Re-install the body on the vehicle.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement. All suspension arms and steering components should move freely. Any binds will cause the vehicle to handle poorly.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

AVC® SENSITIVITY

The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the sensitivity, the AVC® system becomes more sensitive to the vehicle drifting left or right. You would use maximum sensitivity during high speed driving or drag racing, when you want the vehicle to stay in a straight line. As the sensitivity value increases, the amount of steering travel decreases.

Turn the ST RATE knob counter-clockwise to reduce the sensitivity. Turn the ST RATE knob clockwise to increase the sensitivity.

Page 6

DISABLING AVC® TECHNOLOGY

If you participate in organized racing, you may be required to turn AVC off. To turn AVC off:

1. Insert a Bind Plug in the BIND port on the receiver.

2. Insert a second Bing Plug in the DISABLE port on the receiver.

3. Connect a fully charged battery pack to the ESC.

4. Power on the ESC. The orange LED ﬂashes, indicating the receiver is in bind mode.

5. Center the ST TRIM and TH TRIM dials on the transmitter.

6. Press and hold the BIND button while powering on the transmitter.

7. Release the BIND button when the orange LED slowly ﬂashes. The transmitter and receiver are linked when the orange LED is solid.

8. Pull the transmitter trigger to Full Throttle.

9. Push the transmitter trigger to Full Brake, then return the trigger to center.

10. Turn the transmitter steering wheel to Full Right.

11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center. The orange LED ﬂashes once.

12. Remove the Bind Plug from the BIND port only, then power off the receiver to save the settings. The receiver will continuously blink to indicate AVC is disabled.

13. Power off the transmitter.

IMPORTANT: You must calibrate the receiver each time it is placed in bind mode. To activate AVC, see the steps in "Calibrating the Receiver."

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed. The battery connectors may become hot during driving. Batteries will lose performance and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger. When moving forward, the wheels should maintain a straight line without any steering wheel input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to turn the steering wheel.

CHANGING THE TRAVEL ADJUST SETTINGS

1. Hold the trigger in the full brake position and turn the steering wheel to Full Right while powering on the transmitter. The LED ﬂashes rapidly, indicating the programming mode is active.

2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob to adjust the full brake end point. Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left position. Turn the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST TRIM knob to adjust the right end point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings. The minimum Travel is 75%, and the Maximum travel is 150%.

IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate the receiver.

DYNAMITE® FUZE™ 130A SENSORLESS BRUSHLESS ESC

SPECIFICATIONS

Type Sensorless

Constant/Peak 130A/760A

Resistance 0.0004 Ohm

Function Forward/Brake–Forward/Brake Reverse

Operation Proportional forward, proportional reverse with braking delay

Input Voltage 7.4V–14.8V (The motor in this vehicle will not support 14.8V.)

BEC Output 6V/3A

Overload Protection Thermal

Dimensions (LxWxH) 53.5mm x 36mm x 36mm

Weight 79 g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause (xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON. If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause (x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

For sensorless brushless motors:

1. Connect the ESC terminal A (typically designated by a blue wire) to the motor’s terminal A (red wire on a Dynamite® Fuze™ sensorless motor). This may also be changed in Programming Item 12, Motor Rotation, without changing wire connections.

2. Connect the ESC terminal B (typically designated by a yellow wire) to the motor’s terminal B (blue wire on a Dynamite® Fuze™ sensorless motor).

3. Connect the ESC terminal C (typically designated by an orange wire) to the motor’s terminal C (black wire on a Dynamite® Fuze™ sensorless motor).

NOTICE: Always disconnect the battery from the ESC when you have ﬁnished operating your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through over discharge.

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%. Disable any special functions such as ABS, etc.

3. Press the SET button while powering ON the ESC. Release the button as soon as the red LED starts to ﬂash.

4. Calibrate the throttle points by pressing the SET button once after each step.

- Neutral (1 ﬂash)—leave the throttle at rest, untouched

- Full throttle (2 ﬂashes)—pull the throttle fully back

- Full brake/reverse (3 ﬂashes)—push the throttle fully forward

Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside motor wires. The center wire must remain in the center and cannot be moved to another motor tab.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

TEN-SCBE RTR, AVC: 1:10 4WD SCBE • INSTRUCTION MANUAL

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 7

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

ESC FUNCTIONS AND MODES

The ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included settings table to adjust the ESC for your driving conditions.

ESC PROGRAMMING PROCEDURE

Programming is accomplished using the SET button on the ON/OFF switch or Digital Program Box (DYNS3005).

1. Connect a fully charged battery to the ESC.

2. Power ON the ESC using the ESC switch.

3. Hold the SET button for 1 second until the green LED blinks, then release the SET button to enter programming mode.

PROGRAMMABLE ITEMS

Basic Items

1 Running Mode Forward w/ brake Forward/Reverse w/ brake Forward/Reverse

2 Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%

3 Low Voltage Cutoff non-protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

4 Start Mode Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9

PROGRAMMABLE ITEMS

Advanced Items

5 Max Brake Force 25% 50% 75% 100% disable

6 Max Reverse Force 25% 50% 75% 100%

7 Initial Brake Force = Drag Brake Force 0% 20% 40%

8 Neutral Range 6% (Narrow) 9% (Normal) 12% (Wide)

9 Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º

10 Reserved Item

11 Reserved Item

12 Motor Rotation Counterclockwise Clockwise

13 Li-Po Cells Auto Calculate 2 Cells 3 Cells 4 Cells 5 Cells 6 Cells

PROGRAMMABLE VALUE Default Settings

1 2 3 4 5 6 7 8 9

PROGRAMMABLE VALUE Default Settings

1 2 3 4 5 6 7 8 9

4. Press and release the SET button as needed to get to the desired menu option (the Green LED will blink corresponding to the menu item number). Programming menu items 1 through 9 are accessible using the SET button on the ESC. Programming menu items 10 and above are only accessible using the optional ESC programming card. Programming of menu items 10 and 11 is only possible after ﬁrmware updates to the ESC programming card.

5. When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks.

6. Press the SET button to move among the settings based on how many times the red LED blinks (Refer to the table for more information).

7. Save the setting by holding the SET button for 3 seconds.

8. Power OFF the ESC switch and repeat the instructions above to change other settings.

Tip: If desired, the ESC programming can be returned to default settings by powering ON the ESC and holding the SET button for 5 seconds.

DESCRIPTIONS

1. Running Mode

- Forward Only with Brake Intended for competition use, this mode allows only forward and brake controls.

- Forward/Reverse with Brake This mode is the basic all-around mode, allowing forward, reverse and brake controls. To engage reverse while moving forward, apply the brake until the vehicle has come to a complete stop, release brake, then apply the brake again. While braking or in reverse, engaging the throttle will result in the vehicle immediately accelerating forward.

2. Drag Brake Force

Adjusts the amount of brake automatically applied when the throttle is returned to the neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing improved turn-in and your vehicle’s general response to controls.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output power shuts off and the red LED ﬂashes twice repeatedly.

The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries, if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a

8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial acceleration and level 4 gives a stronger initial acceleration.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking, but can also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Initial Brake Force (minimum brake)

Adjusts the minimum amount of braking power when the brakes engage. The default value is equal to the drag brake value. A high value can lock the wheels when the brake is used.

8. Neutral Range

Adjusts the throttle sensitivity around the neutral point. A higher value results in the throttle having to be moved more for the vehicle to move forward, backward or brake.

9. Timing

Adjusts the motor drive current timing. More timing gives more performance, but can lower efﬁciency and cause damage to the motor and/or ESC by overload or overheating.

NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor timing correctly can result in damage to the motor and ESC. Refer to the manufacturer instructions for recommended timing settings.

The Following Programmable Items require the optional Digital ESC Program Box:

10. and 11. Available Items are subject to ﬁrmware updates to the ESC and the optional

digital program box.

12. Motor Rotation

Allows you to make this change in the ESC so no wires need to be changed between the ESC and the motor.

13. Li-Po Cells

Allows the ESC to automatically detect or manually set the number of cells in your Li-Po battery back.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 8

DYNAMITE® FUZE™ 2800KV BRUSHLESS MOTOR

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing for the stock platform. It offers an ideal balance between speed, power and efﬁciency. If you customize your vehicle with optional batteries or motors, you might need to change the pinion or spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth provides more torque but reduced top speed. A pinion gear with more teeth or a spur gear with fewer teeth will reduce torque and increase top speed. Take care when installing larger pinion gears as this can “overgear” the vehicle and overheat the motor and ESC. When testing gearing options, check the temperature of the motor and speed control to ensure you are operating within the appropriate temperature range. If the motor or ESC are too hot, change to a lower pinion gear and/or higher spur gear combination.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels do not rotate

Steering does not work Servo plug not in receiver properly Verify the steering servo plug is connected to the receiver steering channel, noting proper polarity

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

ESC gets hot Motor over-geared Use smaller pinion or larger spur gear

Poor run time and/or sluggish acceleration

Poor range and/or glitching Transmitter batteries low Check and replace

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Servo gears or motor damaged Replace or repair servo

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

Driveline bound up Check wheels and transmission for binding

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 9

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals). This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_service-center_render-servicecenter. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will

be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment will be required without notiﬁcation or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service

you are agreeing to payment of the service without notiﬁcation. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby. com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the unserviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notiﬁcation, after which it will be discarded.

10/15

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 10

Warranty and Service Contact Information

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Germany

Horizon Service Center (Repairs and Repair Requests)

Horizon Product Support (Product Technical Assistance)

Sales

Horizon Technischer Service Sales: Horizon Hobby GmbH

servicecenter.horizonhobby.com/RequestForm/

productsupport@horizonhobby.com 877-504-0233

websales@horizonhobby.com 800-338-4639

service@horizonhobby.eu +49 (0) 4121 2655 100

4105 Filedstone Rd. Champaign, Illinois 61822 USA

Hanskampring 9 D 22885 Barsbüttel, Germany

FCC Statement

FCC ID: BRWDASRX12 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the

R&TTE and EMC Directive. A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the

2.400GHz to 2.4835GHz frequency range.

IC Information

IC ID: 6157 A-AMRX12 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofﬁce, your household waste disposal service or where you purchased the product.

ROCK REY ROCK RACER: 1:10 RTR, AVC • INSTRUCTION MANUAL

Page 11

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part # English Deutsch Français Italiano

DYN4955 Fuze 130A Sensorless Bl WP ESC: 4WD SCT 1/8 Fuze 130A Sensorlose Bl WP ESC: 4WD SCT 1/8 Contrôleur Dynamite Fuze Brushless 130A étanche ESC Fuze WP BL sensorless 130 A: 4WD SCT 1/8 DYNS1614 Fuze 550 BL 6-Pole Motor 2800kv Fuze 550 BL 6-poliger Motor 2800kv LOS230013 Body Button Base & Top (22): Baja Rey Body Button unten und oben (22): Baja Rey Baja Ray - Vis, rondelles et bouchons (22) Viti, rondelle e cappucci di protezione (22): Baja Ray LOS230027 Roll Cage, Sides, L & R: Rock Rey Überrollbügelteile links und rechts: Baja Rey Baja Rey - Faces latérales gauche et droite

LOS230028 Roll Cage, Roof, Front: Rock Rey Überrollkäﬁg, Dach, Vorderseite: Rock Rey Rock Rey - Cage, toit, avant Roll cage, tetto, anteriore: Rock Rey LOS230029 RR Tower Sup, X-Bar, Mud Guards: Rock Rey RR Tower Sup, X-Balken, Schmutzfänger: Rock Rey Rock Rey - Tour de suspension arrière, barre X,

LOS230030 Body, Painted, Blue: Rock Rey Karosserie, lackiert, blau: Rock Rey Rock Rey - Carrosserie, peinte, bleu Carrozzeria, verniciata, blu: Rock Rey LOS230031 Body, Painted, Yellow: Rock Rey Karosserie, lackiert, gelb: Rock Rey Rock Rey - Carrosserie, peinte, jaune Carrozzeria, verniciata, giallo: Rock Rey LOS230032 Interior Panel, Painted: Rock Rey Innenpanel, lackiert: Rock Rey Rock Rey - Panneau de carrosserie intérieur, peinte Pannello carrozzeria interno, verniciato: Rock Rey LOS231005 Rear Bulkhead, Fan Panel, Mudguards: Baja Rey Lüfterpanel, Schmutzfänger: Baja Rey Baja Rey - Cloison arrière, ventilateur et bavettes Paratia post., fan panel, parafango: Baja Rey LOS231006 Battery Tray, Door, Lock, 2S Spacer: Baja Rey Akkuhalter und Klappe, 2S Distanzstück: Baja Rey Baja Rey - Support batterie, trappe, verrou et

LOS231007 FR Upper Arm/Shock Mount, RR Chassis Brace:

Baja Rey LOS231008 Servo Mount, Steering Servo Set Plastic: Baja Rey Servohalter: Baja Rey Baja Rey - Support servo, servo de direction plastique Supporto servo, set servo sterzo in plastica: Baja Rey LOS231010 Chassis Plate & Motor Cover Plate: Baja Rey Chassisplatte und Motorabdeckung: Baja Rey Baja Rey - Platine de châssis et couvercle moteur Piastra telaio & piastra copertura motore: Baja Rey LOS231011 Center Chassis Brace & Standoffs: Baja Rey Chassishalter und Distanzstücke: Baja Rey Baja Rey - Renfort central de châssis et entretoises Montanti telaio centrali con distanziali: Baja Rey LOS231012 Motor Mount: Baja Rey Motorhalter: Baja Rey Baja Rey - Support moteur Supporto motore: Baja Rey LOS231013 Steering Hardware Set: Baja Rey Zubehörset Lenkung: Baja Ray Baja Rey - Set d’accessoires de direction Set hardware sterzo: Baja Rey LOS231021 FR Bumper/Skid Plate & Suppport: Rock Rey FR-Stoßdämpfer/Gleitplatte und -träger: Rock Rey Rock Rey - Pare choc avant/protection et support Paraurti anteriore/piastra proteggitelaio e

LOS231022 Front Shock Tower, Brace, Cmbr Link Mnt: Rock Rey Stoßdämpferbrücke vorne, Halterung, Cmbr Verb.-

LOS232001 Axle Housing Set, Rear: Baja Rey Achsgehäuseset hinten: Baja Rey Baja Rey - Carter de pont arrière Set alloggiamento asse posteriore: Baja Rey LOS232002 Center Transmission Housing: Baja Rey Achsgehäuse mitte: Baja Rey Baja Rey - Boitier de transmission centrale Scatola trasmissione centrale: Baja Rey LOS232003 Front Gear Box/Bulkhead: Baja Rey Getriebegehäuse mit Halter: Baja Rey Baja Rey - Set de carters de transmission avant/Cellule Scatola ingranaggio anteriore / paratia: Baja Rey LOS232004 HD Diff Housing & Internals: Baja Rey Differentialgehäuse mit Einsätzen: Baja Rey Baja Rey - Corps de différentiel renforcé et

LOS232005 Rear Driveshaft Set: Baja Rey Antriebswelle hinten: Baja Rey Baja Rey - Tiges de cardans arrière Set trasmissione posteriore: Baja Rey LOS232006 Hex, Rotor, Caliper & Pin Set (4): Baja Rey Scheibenbremse mit Bremssattel Vorne/Hinten:

LOS232007 Center Transmission Gear Set: Baja Rey Getriebeset Mitte: Baja Rey Baja Rey - Set de pignons de transmission centrale Set ingranaggio trasmissione centrale: Baja Rey LOS232010 Center Drive Shaft: Baja Rey Antriebswelle Mitte: Baja Rey Baja Rey - Cardan central Albero di trasmissione centrale: Baja Rey LOS232011 Rear Diff Locker: Baja Rey Differentialsperre hinten: Baja Rey Baja Rey - Verrou de diff arrière Diff. locker posteriore: Baja Rey LOS232012 Center Outdrive Set: Baja Rey Antriebsklaue mitte: Baja Rey Baja Rey - Set de noix de cardans centraux Set trascintore centrale: Baja Rey LOS232014 Rear Axle Shaft Set: Baja Rey Hinterachsewellenset: Baja Rey Baja Rey - Axe de roues arrière Set semiasse posteriore: Baja Rey LOS232019 42T Ring & 12T Pinion Gear: Baja Rey/Rock Rey Stirnrad 42 Zähne & 12 er Ritzel: Baja Rey/Rock Rey Baja Rey/Rock Rey - Anneau 42T et Pignon 12T

LOS232020 Front Axle Set: Rock Rey Vorderes Achsenset: Rock Rey Rock Rey - Axe de roues avant Set asse anteriore: Rock Rey LOS232021 Front Sliders: Rock Rey Vordere Schieber: Rock Rey Rock Rey - Sliders avant Steli forcella anteriore: Rock Rey LOS232022 Front Outdrive Shaft: Rock Rey Vordere Flexwelle: Rock Rey Rock Rey - Axe de transmission avant Albero trascinatore anteriore: Rock Rey LOS233001 Shock Ends, Tops, Piston: Baja Rey Stoßdämpferendteile, Kolben: Baja Rey Baja Rey - Chapes d’amortisseurs, bouchons

LOS233002 FR/RR Shock Body & Collar Set: Baja Rey Stoßdämpfergehäuse, Distanzringe v/h: Baja Rey Baja Rey - Corps d’amortisseurs avant/arrière

LOS233003 FR/RR Shock Shaft Set & Hardware: Baja Rey Dämpfer Kolbenstange mit Zubehör: Baja Rey Baja Rey - Tiges d’amortisseurs avant/arrière

LOS233004 FR/RR Shock Seal & Limiter Set: Baja Rey Stoßdämpferdichtung und Begrenzer: Baja Rey Baja Rey - Joint d’amortisseurs avant/arrière

LOS233005 Front and Rear Spring Set: Baja Rey Dämpferfedern v/h: Baja Rey Baja Rey - Ressort avant/arrière Set molle ant./post.: Baja Rey LOS234002 Shock Tower, Upper/Track Rod Mnts, Rear: Baja Rey Dämpferbrücke hinten: Baja Rey Baja Rey - Support d’amortisseurs, tirants Torretta ammortizz., supporti tirante sterzo

LOS234003 Trailing Arm, Steering,Upper, Drag Link St: Baja Rey Lenkgestänge: Baja Rey Baja Rey - Tringlerie de direction supérieure Braccetto longitudinale, sterzo, superiore, tirante

LOS234006 Front & Rear Sway Bar Links: Baja Rey Querlenkerverbinder vorne: Baja Rey Baja Rey - Tringlerie barre anti-roulis avant/arrière Collegamenti barra antitorsione ant./post.: Baja Rey LOS234007 Front Hinge Pins & Brace Set: Baja Rey Qiuerlenkerstifte und Halter: Baja Rey Baja Rey - Renfort de cellule avant Perni braccetti ant. e set piastrine LOS234011 Front Suspension Arm Set: Rock Rey Vorderradaufhängungsarm Set: Rock Rey Rock Rey - Bras de suspension avant Set braccetti sospensione anteriore: Rock Rey LOS234012 Caster Block Set: Rock Rey Radblockset: Rock Rey Rock Rey - Etriers porte fusées Set caster block: Rock Rey LOS234013 Steering Spindle Set: Rock Rey Lenkspindelset: Rock Rey Rock Rey - Fusées Fusello sterzo: Rock Rey LOS234014 Camber & Steering Link Set: Rock Rey Radsturz- und Lenkgliedset: Rock Rey Rock Rey - Rotules de carrossage et direction Set campanatura e collegamenti sterzo: Rock Rey LOS234015 FR/RR Shock Body & Collar Set: Rock Rey FR/RR Stoßdämpfer & Collar Set: Rock Rey Rock Rey - Corps d’amortisseurs avant/arrière

LOS235001 Cap Head Screws, M2 x 6mm (10) Zylinderkopfschraube, M2 x 6mm (10) Vis BTR, M2 x 6mm (10) Viti testa a brugola, M2 x 6mm (10) LOS235002 Cap Head Screws, M2.5 x 10mm (10) Zylinderkopfschraube, M2.5 x 10mm (10) Vis BTR, M2,5 x 10mm (10) Viti testa a brugola, M2,5 x 10mm (10) LOS235003 Cap Head Screws, M3 x 6mm (10) Zylinderkopfschraube, M3 x 6mm (10) Vis BTR, M3 x 6mm (10) Viti testa a brugola, M3 x 6mm (10) LOS235004 Cap Head Screws, M3 x 25mm (10) Zylinderkopfschraube, M3 x 25mm (10) Vis BTR, M3 x 25mm (10) Viti testa a brugola, M3 x 25mm (10) LOS235005 Button Head Screws, M2.5 x 6mm (10) TLR Rundkopfschraube, M2.5 x 6mm (10) Vis à tête bombée, M2,5 x 6mm (10) Viti testa tonda, M2,5 x 6mm (10) LOS235006 Button Head Screws, M2.5 x 20mm (10) TLR Rundkopfschraube, M2.5 x 20mm (10) Vis à tête bombée, M2,5 x 20mm (10) Viti testa tonda, M2,5 x 20mm (10) LOS235007 Button Head Screws, M4 x 12mm (10) TLR Rundkopfschraube, M4 x 12mm (10) Vis à tête bombée, M4 x 12mm (10) Viti testa tonda, M4 x 12mm (10) LOS235008 Flat Head Screws, M2.5 x 5mm (10) Flachkopfschraube, M2.5 x 5mm (10) Vis FHC, M2,5 x 5mm (10) Viti a testa piatta, M2,5 x 5mm (10) LOS235009 Flat Head Screws, M2.5 x 8mm (10) Flachkopfschraube, M2.5 x 8mm (10) Vis FHC, M2,5 x 8mm (10) Viti a testa piatta, M2,5 x 8mm (10)

Stoßdämpferbefestigung hinten mit Chassishalter: Baja Rey

Mnt: Rock Rey

Baja Rey

Moteur Dynamite Fuze Brushless 550 2800Kv 6 pôles

de l’arceau cage

pare choc

cales 2S Baja Rey - Triangle supérieur/ﬁxation

d’amortisseur avant, renfort arrière de châssis

Rock Rey - Support d’amortisseurs av, protection et support biellette de carrossage

éléments internes

Baja Rey - Hexagone, rotor, mâchoires et goupilles

avant/arrière

supérieurs et pistons

avec bague

avec visserie

avec limiteur

avec bague

Motore BL Fuze 550 6 poli 2800 Kv

Parti laterali roll cage D&S: Baja Rey

Torretta sospensione posteriore, barra a X, parafanghi: Rock Rey

Vano batteria, portello, chiusura, distanziale 2S: Baja Rey

Braccetto superiore ant. / supporto ammortizz., trapezio post.: Baja Rey

supporto: Rock Rey Torretta ammortizzatore anteriore, trapezio,

supporto camber link: Rock Rey

Scatola diff. HD ed parti interne: Baja Rey

Set esagone, rotore, spessore e perno: Baja Rey

42T ingranaggio & 12T pignone ant./post.: Baja Rey/Rock Rey

Terminali, tappi, pistoni ammortizz.: Baja Rey

Corpo ammortizz. ant./post & collarino

Stelo ammortizz. ant./post e hardware: Baja Rey

Set guarnizione ammortizz. ant./post. e limitatore: Baja Rey

superiore post.: Baja Rey

sterzo: Baja Rey

Set corpo ammortizzatore ant./post. e collarino: Rock Rey

ROCK REY ROCK RACER: 1:10 RTR, AVC

ROCK REY ROCK RACER: 1:10 RTR, AVC • MANUALE DI ISTRUZIONI

Page 12

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part # English Deutsch Français Italiano

LOS235010 Flat Head Screws, M2.5 x 12mm (10) Flachkopfschraube, M2.5 x 12mm (10) Vis FHC, M2,5 x 12mm (10) Viti a testa piatta, M2,5 x 12mm (10) LOS235011 Set Screws, M3 x 3mm Cup Point (10) Ringschneide Gewindestift, M3 x 3 (10) Vis à tête creuse auto-taraudeuses M3 x 3 (10) Set viti a grano M3 x 3 mm (10) LOS235012 Set Screws, M4 x 4mm Cup Point (10) Ringschneide Gewindestift, M4 x 4 (10) Vis à tête creuse auto-taraudeuses M4 x 4 (10) Set viti a grano M4 x 4 mm (10) LOS235013 Flat Nut, M3 x 0.5 x 5mm (10) Flachmutter, M3 x 0.5 x 5mm (10) Écrou plat, M3 x 0,5 x 5mm (10) Dado piatto, M3 x 0,5 x 5mm (10) LOS235014 Lock Nut, M2 x 0.4 x 4mm (10) Muttern Nylock angeﬂanscht, M2 x 0.4 x 4mm (10) Écrou auto-freiné M2 x 0,4 x 4mm (10) Dadi autobloccanti M2 x 0,4 x 4 mm (10) LOS235015 Lock Nut, Flanged M5 x 0.8 Serrated (10) Muttern Nylock angeﬂanscht gezackt, M5 x 0.8 (10) Écrou auto-freiné épaulé strié M5 x 0,8mm (10) Dadi a colletto dentato M5 x 0,8 (10) LOS235023 Hinge Pin Screws, FR (10): Rock Rey Scharnierstiftschrauben, FR (10): Rock Rey Rock Rey - Vis de cellule avant (10) Viti perni cerniere ant. (10): Rock Rey LOS239001 Fluorescent Yellow Decal Sheet: Rock Rey Aufkleberbogen/Fluor Gelb: Rock Rey Rock Rey - Planche de décoration jaune ﬂuo Decalcomanie giallo ﬂuorescente: Rock Rey LOS239002 Electric Blue Decal Sheet: Rock Rey Aufkleberbogen/Blau: Rock Rey Rock Rey - Planche de décoration bleue électrique Decalcomanie blu elettrico: Rock Rey LOS330001 LED Roof Light Bar Set: Baja Rey LED-Leuchtbalkenset, Dach: Baja Rey Baja Rey - Rampe lumineuse DEL toit Barra luci LED tetto: Baja Rey LOS43012 Maxxis Creepy Crawler LT Mounted 2.35" x 5.75" - 2.2 Maxxis Creepy Crawler LT montiert Pneus montés Maxxis Creepy Crawler LT Maxxis Creepy Crawler LT montato LOS43013 Maxxis Creepy Crawler LT Tire 2.35" x 5.75" - 2.2" Maxxis Creepy Crawler LT Reifen Pneus Maxxis Creepy Crawler LT Pneumatico Maxxis Creepy Crawler LT LOS43014 Wheels 2.2" (4): Rock Rey Räder 2.2" (4): Rock Rey Rock Rey - Roues 2,2" (4) Ruote 2,2" (4): Rock Rey

LOSA3572 1.0 Module Pitch Pinion, 12T

LOSA6250 Set Screws, 4mm & 5mm (6) Madenschraube, 4mm & 5mm (6) Vis STHC, 4mm & 5mm (6) Grano, 4mm & 5mm (6) LOSA6937 5 x 10mm Shielded Ball Bearing (2) 5x10mm Kugellager mit Staubschutzscheibe (2) Roulements épaulés 5 x 10mm (2) Cuscinetto a sfera schermato 5 x 10 mm (2) LOSA6940 6 x 12mm Sealed Ball Bearing (4) 6 x 12mm Kugellager mit Gummiabdeckung (4) Roulements étanches 6 x 12mm (4) Cuscinetto a sfera sigillato 6 x 12 mm (2) LOSA6956 12 x 18 x 4mm Ball Bearing (2) 12 x 18 x 4mm Kugellager (2) Roulements 12 x 18 x 4mm (2) Cuscinetto a sfera 12 x 18 x 4 mm (2) LOSA6957 10 x 15 x 4mm BB (2) with Nylon Retainer 10 x 15 x 4mm Kugellager (2) with Nylon Retainer Roulements 10 x 15 x 4mm ﬂasque nylon (2) Cuscinetto a sfera 10 x 15 x 4 mm con fermo di nylon (2) LOSB3008 3 x 6 x 2.5mm Ball Bearing (2) 3 x 6 x 2.5mm Kugellager (2) Roulements 3 x 6 x 2,5mm (2) Cuscinetto a sfera 3 x 6 x 2,5 mm (2) SPMS612HV 12KG Servo, WP, Metal, 23T 12KG WP-Metall-Servo 23T Servo 12kg à pignons métal, étanche, 23T Servo 12 kg, resistente all’acqua, metallo, 23T SPMSRS4220 SRS4220 DSMR AVC Surface Rx SRS4220 DSMR AVC Sender Récepteur SRS4220 DSMR AVC Radio AVC DSMR SRS4220 TLR5903 Button Head Screws, M3 x 10mm (10) Halbrundschraube, M3 x 10mm (10) Vis à tête bombée, M3 x 10mm (10) Viti a testa tonda, M3 x 10mm (10) TLR5904 Button Head Screws, M3 x 12mm (10) Halbrundschraube, M3 x 12mm (10) Vis à tête bombée, M3 x 12mm (10) Viti a testa tonda, M3 x 12mm (10) TLR5909 Button Head Screws, M3 x 16mm (10) Halbrundschraube, M3 x 16mm (10) Vis à tête bombée, M3 x 16mm (10) Viti a testa tonda, M3 x 16mm (10) TLR5910 Button Head Screws, M3 x 14mm (10) Halbrundschraube, M3 x 14mm (10) Vis à tête bombée, M3 x 14mm (10) Viti a testa tonda, M3 x 14mm (10) TLR5911 Button Head Screws, M3 x 20mm (10) Halbrundschraube, M3 x 20mm (10) Vis à tête bombée, M3 x 20mm (10) Viti a testa tonda, M3 x 20mm (10) TLR5913 Button Head Screws, M2.5 x 12mm (10) Halbrundschraube, M2.5 x 12mm (10) Vis BHC, M2,5 x 12mm (10) Viti a testa tonda, M2,5 x 12mm (10) TLR5934 Cap Head Screws, M3 x 16mm (10) Sechskantschraube, M3 x 16mm (10) Vis CHC M3 x 16mm (10) Viti a testa piatta M3 x 16mm (10) TLR5961 Flathead Screws, M3 x 8mm (10) Flachkopfschraube, M3 x 8mm (10) Vis FHC, M3 x 8mm (10) Viti a testa piatta, M3 x 8mm (10) TLR5963 Flathead Screws, M3 x 12mm (10) Flachkopfschraube, M3 x 12mm (10) Vis FHC, M3 x 12mm (10) Viti a testa piatta, M3 x 12mm (10) TLR5964 Flathead Screws, M3 x 16mm (10) Flachkopfschraube, M3 x 16mm (10) Vis FHC, M3 x 16mm (10) Viti a testa piatta, M3 x 16mm (10) TLR5965 Flathead Screws, M3 x 20mm (10) Flachkopfschraube, M3 x 20mm (10) Vis FHC, M3 x 20mm (10) Viti a testa piatta, M3 x 20mm (10) TLR5965 Flathead Screws, M3 x 20mm (10) Flachkopfschraube, M3 x 20mm (10) Vis FHC, M3 x 20mm (10) Viti a testa piatta, M3 x 20mm (10) TLR6312 Locknut, M2.5 x .45 x 5mm (6) Muttern Nylock angeﬂanscht, M2.5 x .45 x 5mm (6) Ecrou auto-freiné M2,5 x 0,45 x 5mm (6) Dadi autobloccanti, M2,5 x .45 x 5 mm (6) TLR6313 Locknut, M3 x .5 x 5.5mm (10) Muttern Nylock angeﬂanscht, M3 x 0.5 x 5.5mm (10) Ecrou auto-freiné M3 x 0,5 x 5,5mm (10) Dadi autobloccanti, M3 x .5 x 5,5 mm (10) TLR6352 Washers, M3 (10) TLR U-Scheibe, M3 (10) Rondelles M3 (10) Rondelle, M3 (10) TLR74006 Silicone Shock Oil, 30wt, 2oz Silikon-Stoßdämpferöl, 30 wt, 60 ml (2 oz) Huile silicone d’amortisseur, 30wt, 60 ml Olio al silicone per ammortizzatore, 30wt, 2oz

VTR236025 M4 Nylock Flanged Nut (10)

VTR246001 Screw Pin, Clip Post (10): Glamis Uno Stiftschraube (10) GLU Supports de clips avec goupilles (10): GLU Perni viti clip (10): GLU

Optional Parts // Optionale Bauteile // Pièces optionnelles // Pezzi opzionali

Part # English Deutsch Français Italiano

DYN9005EC Reaction 7.4V 5000mAh 2S 30C LiPo Hardcase: EC3 Reaction 7,4 V 5000 mAh 2S 30C LiPo,

DYNB3803EC Reaction 11.1V 5000mAh 3S 50C LiPo, Hardcase:

EC3 DYNC2005CA Prophet Sport LiPo 35W AC Charger Prophet Sport LiPo 35 W AC-Ladegerät Chargeur Prophet Sport AC Li-Po 35W Caricabatteria AC LiPo Prophet Sport 35 W LOS330002 Body Set, Clear: Rock Rey Karosserie Set: Rock Rey Rock Rey - Carrosserie, transparente LOS331001 Aluminum Steering Servo Mount: Baja Rey Aluminium Lenkservo Montage: Baja Rey Baja Rey - Support de servo de direction aluminium Supporto servocomando sterzo alluminio: Baja Rey LOS331002 Aluminum Bellcrank Servo Saver Set: Baja Rey Aluminium Umlenkhebel-Servo Sparset:

LOS331004 Aluminum Rear Upper Link & Space Set:

Baja Rey LOS331005 Aluminum Servo Arm, 23T: Baja Rey LOS331006 Aluminum Servo Arm, 24T: Baja Rey LOS331007 Aluminum Servo Arm, 25T: Baja Rey LOS332001 AL Lightened Hex Adapter Set, 12mm x 6mm:

Baja Rey LOS334002 AL Axle Housing Upper Track Rod Mount:

Baja Rey LOS334003 AL Upper/Lower Blkhd Track Rod Mount St:

Baja Rey LOS334004 Aluminum Rear Shock Tower Set: Baja Rey LOS334006 Aluminum Lower Rear Trailing Arm Set: Baja Rey Aluminium Hinterachsträgerset unten: Baja Rey Baja Rey - Bras arrière inférieur aluminium Braccetto longitudinale inf. alluminio: Baja Rey LOSA3570 1.0 Module Pitch Pinion, 10T: 8E, SCTE 1.0 Modul Getrieberad, 10T: 8E, SCTE 8E, SCTE - Pignon module 1.0, 10T Pignone 10T modulo 1: 8E, SCTE LOSA3571 1.0 Module Pitch Pinion, 11T: 8E, SCTE 1.0 Modul Getrieberad, 11T: 8E, SCTE 8E, SCTE - Pignon module 1.0, 11T Pignone 11T modulo 1: 8E, SCTE TLR76000 Tire Glue, Standard TLR76004 TLR Lok, Threadlock, Blue

Hardcasemit: EC3

Reaction 11,1 V 5000 mAh 3S 50C LiPo,

Hardcasemit: EC3

Baja Rey Aluminium hinteres oberes Glied- und

Abstandsset: Baja Rey

Servoarm, Aluminium, 23T: Baja Rey Baja Rey - Palonnier de servo, alu, 23T Squadretta servo, alluminio, 23T: Baja Rey Servoarm, Aluminium, 24T: Baja Rey Baja Rey - Palonnier de servo, alu, 24T Squadretta servo, alluminio, 24T: Baja Rey Servoarm, Aluminium, 25T: Baja Rey Baja Rey - Palonnier de servo, alu, 25T Squadretta servo, alluminio, 25T: Baja Rey

AL erleuchtetes Hex-Adapterset, 12 mm x 6 mm: Baja Rey

AL Achsgehäuse Obere Spurstangen-Montage: Baja Rey

AL Blkhd Spurstangen-Montage oben/unten St: Baja Rey

Heck Stoßdämpferbrücke Aluminium: Baja Rey Baja Rey - Support d’amortisseurs arrière en alu Torre ammortizzatore posteriore, allum: Baja Rey

Reifenkleber, Standard Colle à pneus, standard Colla pneumatici, standard TLR Lok, Schraubensicherung, Blau Frein ﬁlet TLR Lok, bleu Frenaﬁletti blu TLR Lok

Batterie Reaction Li-Po 2S 7,4V 5000mA 30C, boîtier rigide, prise EC3

Batterie Reaction Li-Po 3S 11,1V 5000mA 50C, boîtier rigide, prise EC3

Baja Rey - Sauve servo levier aluminium Set salvaservo squadrette alluminio: Baja Rey

Baja Rey - Tirant supérieur arrière et entretoise aluminium

Baja Rey - Hexagones aluminium, 12mm x 6mm Adattatore esagonale allum. alleggerito, 12 mm x

Baja Rey - Carter de pont supérieur aluminium Track Rod Mount

Baja Rey - Cellule supérieure/inférieure aluminium Track Rod Mount

Batteria LiPo hardcase Reaction 30C 2S 7,4 V 5000 mAh: EC3

Batteria LiPo hardcase Reaction 50C 3S 11,1 V 5000 mAh: EC3

Set carrozzeria trasparente

Set collegamento e distanziale superiore posteriore alluminio: Baja Rey

6 mm: Baja Rey Supporto tirante sterzo superiore allum.

alloggiamento asse: Baja Rey Supporto tirante sterzo allum. paratia sup./inf.:

Baja Rey

ROCK REY ROCK RACER: 1:10 RTR, AVC • MANUALE DI ISTRUZIONI

ROCK REY ROCK RACER: 1:10 RTR, AVC

Page 13

EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE PARTI

LOS330001

TLR5913

LOS230030/ LOS230031

LOS230032

LOS230030/ LOS230031

LOS230013

LOS230030/

LOS230031

LOS235006

LOS230029

LOS235006

LOS230027

LOS235006

LOS235006LOS235006

LOS230029

LOS43012

LOS230029

TLR5913

LOS230028

TLR5909

ROCK REY ROCK RACER: 1:10 RTR, AVC

LOS230028

TLR5913

LOS230030/

LOS230031

LOS230027

LOS235006

LOS230029

LOS235006

Page 14

SPMSRS4220

TLR5904

TLR6352

TLR5909

LOS232002

TLR5904

TLR6352

LOS232007

DYN4955

LOS232007

LOSA6250

LOSA6937

LOSA3572

LOS232012

SPMS612HV

LOS232004

TLR6313

LOS232007

LOSA6956

LOS232004

LOS231008

LOSB3008

VTR236025

LOS231013

LOSB3008

LOS231013

LOS231008

TLR6313

LOSB3008

LOS231013

LOS231008

TLR6352

TLR5910

LOS231008

TLR6313

LOS234008

LOS235003

LOS232002

LOS231012

DYNS1614

LOSA6956

LOS232012

TLR6313

LOS231008

LOS234008

TLR6352

TLR5910

LOS235005

TLR6352

EXPLODED VIEW

EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE DES PIÈCES

VISTA ESPLOSA DELLE PARTI

TLR5910

LOS234007

ROCK REY ROCK RACER: 1:10 RTR, AVC • MANUALE DI ISTRUZIONI

ROCK REY ROCK RACER: 1:10 RTR, AVC

Page 15

LOS233001

LOS234008

LOS233001

LOS233002

LOS233001

LOS233004

LOS233001

TLR6312

LOS233003

LOS233005

LOS233002

LOS233001

LOS233003

LOS233001

LOS234008

TLR6313

LOS234014

LOS234008

TLR5911

LOS234013

LOS234008

VTR235015

TLR6313

LOS234013

LOS235005

LOS235001

LOS235008

LOS233006

LOS232009

LOSA6940

VTR246001

LOS235005

LOS234012

LOS234011

TLR6352

LOS232006

LOS235001

TLR5909

LOS234013

LOS235023

LOS232006

LOS234005

LOS235023

TLR5934

LOS235001

LOS235014

TLR5965

LOS232003

LOS232010

VTR246001

LOS234007

LOSA6937

LOS232020

LOS232012

VTR235015

LOS232019

LOS232021

TLR5911

LOSA6957

VTR246001

LOS232022

TLR5934

TLR5965

LOS232003

LOS235001

EXPLODED VIEW

EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE DES PIÈCES

VISTA ESPLOSA DELLE PARTI

ROCK REY ROCK RACER: 1:10 RTR, AVC

LOS234007

LOS235001

LOSA6957

VTR246001

LOS234007

LOS232004

LOS232022

LOS232004

LOS232019

Page 16

LOS235006

LOS234002

TLR5911

TLR5913

LOS231005

LOS235006

TLR5913

LOS235011

LOS234002

LOS230012

LOS231005

LOS235009

TLR5911

TLR6313

LOS235002

LOS231022

LOS235009

TLR5911

LOS232005

TLR5934

LOS231005

LOS235011

TLR5904

LOS234002

LOS230012

TLR5963

TLR5965

LOS234002

LOS234006

TLR6313

TLR5911

LOS234002

LOS235004

LOS234002

TLR6313

TLR5911

LOS234006

TLR5909

LOS235002

TLR5965

TLR6313

LOS234006

TLR5904

LOS232005

LOS231006

TLR5965

LOS234006

TLR6313

LOS235011

TLR6313

LOS234006

TLR5911

LOS234002

TLR5965

TLR5909

LOS234006

TLR6313

LOS231006

TLR5963

LOS231007

TLR5963

TLR5911

LOS231022

TLR5963

LOS231022

CHASSIS EXPLODED VIEW

CHASSIS EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE DU CHÂSSIS

VISTA ESPLOSA DEL TELAIO

TLR5934

TLR5910

TLR5911

TLR5903

LOS231022

LOS235002

TLR5910

LOS231021

LOS235002

LOS231021

LOS235001

LOS231006

TLR5910

TLR6352

LOS231008

TLR5935

TLR5961

LOS231011

TLR5663

TLR5961

LOS235009

TLR5963

TLR5961

LOS231010

LOS235009

TLR5963

LOS231010

LOS231011

ROCK REY ROCK RACER: 1:10 RTR, AVC • MANUALE DI ISTRUZIONI

ROCK REY ROCK RACER: 1:10 RTR, AVC

Page 17

LOS233001

LOS233004

LOS234008

LOS233001

LOS233004

LOS233002

LOS233001

LOS233005

LOS233002

TLR6312

LOS233001

LOS233003

TLR5909

LOS233001

LOS233004

LOS234008

LOS233004

TLR5911

TLR6313

TLR5911

LOS233001

TLR6313

TLR5904

LOS234008

LOS232001

LOSA6957

LOS232014

TLR5964

LOSA6940

LOS232006

LOS232001

VTR246001

LOS232006

LOS232014

TLR5964

TLR5911

LOS232014

LOSA6940

TLR5911

LOS232001

LOS234008

LOS232014

LOSA6957

LOS234008

LOS232011

LOS232019

LOS232004

TLR6313

LOSA6937

TLR5943

LOS234003

LOS232004

LOS232019

LOS232001

TLR5943

LOSA6937

TLR6313

LOS234003

LOS234008

LOS234003

LOS234008

TLR5964

LOS232006

LOSA6940

REAR EXPLODED VIEW

HECK EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE ARRIÈRE

VISTA ESPLOSA DELLA PARTE POSTERIORE

LOS232006

ROCK REY ROCK RACER: 1:10 RTR, AVC

LOS232001

LOS232014

VTR246001

TLR5911

LOS234008

LOS234003

LOS234008

LOS232005

Page 18

Notes

Page 19

Notes

Page 20

WWW.LOSI.COM

© 2017 Horizon Hobby, LLC. Losi, Rock Rey, DSM, DSM2, DSMR, AVC, Active Vehicle Control, EC3, Dynamite, Fuze, Prophet , Reaction and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. US 9,320,977. Other patents pending.

Upldated 04/17 51556.2 | LOS03009T1/T2