LOREX Technology Quad Surveillance System User Manual

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Skill Level

Time

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Time Tools Skills - Easy

SHS-4QM SERIES

QUAD SURVEILLANCE SYSTEM

QUICK SET-UP GUIDE

WITH 4 CCD INDOOR/OUTDOOR CAMERAS*

STEP 1

Getting Started

The SHS System comes with the following components:

• Quad Processor

• 2 x Weatherproof Color Cameras with Stands

• 2 x Weatherproof Color Day/Night IR Cameras with Stands

• 4 x 60’ DIN Extension Cables

• DIN Video Cable

• Remote Control

• Power Adapter

Check your package to confirm that you have received the
complete system, including all components shown above.

Night Vision

Cameras

Day Use

Cameras

Under 10 Minutes*

* Installation time may vary based

on application and camera cabling

Hand Tools

Plug & Play connectors, On

screen set up

B. Connecting the DIN Video Cable

Connect the DIN end of the Video Cable to the Quad Processor. Connect the RCA VIdeo cable
to the TV, VCR or Monitor.

TV / VCR / MONITOR

Connect the Yellow RCA

connector to the TV Video IN

Port (yellow)

QUAD PROCESSOR

Connect the DIN Cable end

to the Video Output port

A. Connect Cameras

Before you install the camera, carefully plan where and how you will position the camera, and where you will route the cables

* IR illumination range up to 16 ft. (5M) under ideal conditions. Objects at or beyond this range may be partially or completely obscured,
depending on the camera application. Picture changes from Color to B&W under low light conditions.

* Note that the IR Night Vision Cameras have a black lens cover.

1

Connect the female end of the supplied 60’
extension’ cable to the camera.

NOTE: Confirm that the arrows
on the DIN Camera Cable and the
DIN Extension cable are aligned
when connecting the cable. If the
pins in the DIN Cable are bent, the
Camera will NOT function.

2

Connect the male end of the supplied 60’
extension cable to an open DIN channel on
the back of the Quad Processor. Continue
connecting additional DIN cameras.

NOTE: The arrow on
the DIN Connector
Connector should
be facing up when
connecting it to the
Quad Processor.

Connectivity Diagram

TV / VCR / MONITOR

SHS CABLE

RCA to DIN Cable

POWER ADAPTER

4 x CAMERAS

4 x 60’ EXTENSION CABLES

SHS-4QM SERIES Quick Set-Up Guide R1

www.lorexcctv.com

DIN CABLE

QUAD PROCESSOR

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Skill Level

Time

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Time Tools Skills - Easy

SHS-4QM SERIES

MENU, MOTION SENSING

QUICK SET-UP GUIDE

& EVENT SET-UP

STEP 2

Full Function Remote Control with Multiple Viewing Modes

PIP

Split

Dual PIP

Quad

Freeze

Zoom

A: Access the Menu System

Menu Set-up

• Press the MENU button for 3 seconds to
enter Menu Mode.

• Press the buttons to navigate
within the Menu and choose the desired
selection.

• Press the ENTER button to accept the
selection.

• Press the MENU button to Exit the Menu
Setup.

Under 20 Minutes*

* Installation time may vary based

on application and camera cabling

Hand Tools

Plug & Play connectors, On

screen set up

B: Enter the Motion Setup Menu

Motion Setup

• Use the arrows to move between
cameras.

• Use the arrows to move between
Menu Settings.

• Set the Motion Detection Time as
desired (Always ON, OFF or for a
specific timeframe).

• Set the Sensitivity (amount of motion
needed to trigger an alarm) and the
Velocity (speed of motion needed to
trigger an alarm).

• Set the Masking Area:

· Use the arrow keys to navigate
through grid.

· Press the ENTER button to select or
deselect a square on the grid.

· Areas set to detect motion are not
shaded. Masked areas in blue do not
detect motion.

· Each area (grid square) must be
selected individually.

• Press the MENU button to Exit. All
settings will be saved.

C: Access the Event Setup Menu

Event Setup

It’s all on the Web

www.lorexcctv.com

For detailed setup information, please

refer to your User’s Manual. For additional

information, please visit our website

www.lor excctv. com/sup port

SHS-4QM SERIES Quick Set-Up Guide R1

• Use the arrow keys to navigate

• Press ENTER to turn on ALARM EVENT
REPORTING for each camera detecting
Motion.

• Press ENTER to turn on MOTION EVENT
REPORTING for each camera detecting
Motion.

• When Motion is detected, the SHS
system will switch to the Camera, and an
audible alarm will sound.

www.lorexcctv.com