LOREX Technology QLR1660 User Manual
MODEL:
QLR1660
Copyright © 2007 Lorex Technology Inc.
SURVEILLANCE SYSTEM
16 CHANNEL
DIGITAL NETWORK
Instruction Manual
English Version1.0
www.lorexcctv.com
QLR1660 User Manual
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
Operation of this equipment in a residential area is likely to cause harmful interference in which case that you will be
required to correct the interference at one’s own expense.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR
COM PLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
THIS DEVICE MAY NOT NOTE HARMFULL INTERFERENCE, AND
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY NOTE UNDERSIRED
OPERATION.
2
DIGITAL VIDEO RECORDER
Important Safety Instructions
1) Read & Retain Instructions
All the safety and operating instructions should be read before the appliance is operated.
The safety and operating instructions should be retained for future reference.
2) Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
3) Follow Instructions
All operating and use instructions should be followed.
4) Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning the unit. (Exception: A product that is meant for uninterrupted service and that for some specific
reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be
unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the product in the
cleaning description otherwise required in 5).
5) Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
6) Water and Moisture
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, or laundry tube in a wet
basement or near a swimming pool and the like.
7) Accessories
Do not place this product on an unstable cart, stand, tripod, bracket or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket or table recommended by the manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer's instructions, and should use a mounting accessory recommended by the
manufacturer.
8) Handling
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
9) Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from overheating and these openings must not be blocked or covered.
Placing the product on a bed, sofa, rug or other similar surface, should never block the openings. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
10) Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or
electric shock.
11) Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short
out parts that could result in a fire or electric shock. Never spill liquid of any kind on the receiver.
12) Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous volt-age
or other hazards. Refer all servicing to qualified service personnel.
13) Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
3
QLR1660 User Manual
CONTENTS
SECTION 1 - PRODUCT INFORMATION
Video Capture Card Specifications ….……………………………..…...…………..………………..............
1.
System Requirement …..……………………………………………………………….................................
2.
Package Contents………………………………………………………………………….………...................
3.
SECTION 2 - INSTALLATION INTRODUCTIONS
QLR1660 Hardware Installations………………………………………………………..............................
1.
Video Capture Card Installation………………………………………………………………………………...
1-1.
Camera Installation………………………………………………………………………………………………
1-2.
Audio & External Sensor/Relay Installation…………………………………………………………………...
1-3.
QLR1660 Device driver Installation………...…………………...............………………………................
2.
QLR1660 Software Installations ……..….............................................................................................
3.
SECTION 3 - HOW TO USE QLR1660 SERVER
Main Interface Window ……………………………………………………….…………………….................
1.
Local Setup Mode ………………………………………………………………............................................
2.
System Setup………………………………………………………………....................................................
2-1.
Camera Setup…………………………………………………………………………….................................
2-2
Schedule Record Setup…………………………………………………………………................................
2-3
Motion Setup…………………………………………………………............................................................
2-4.
Sensor Setup………………………………………………………………….................................................
2-5.
Speaker, Relay out Setup………………………………………………………….........................................
2-6.
Mail Setup…………….............................................................................................................................
2-7.
User Registration Setup…………………………………………………………………………………...……
2-8
SECTION 4 - HOW TO USE QLR1660 SEARCH
Main Interface Window ……………………………………………………….…………………….................
1.
Local Search Mode……………………………………………………………………………….....................
2.
Remote Search Mode………………... ……………………………………………………..…………...…….
3.
SECTION 5 - HOW TO USE QLR1660 CLIENT
Main Interface Window ……………………………………………………….…………………….................
1.
Remote View Mode............................................…………………………………............................………
2.
Local Setup Mode……………………………………………………………..………………….....................
2-1.
Connecting to the QLR1660 Server……………………………………………………………..................
2-2.
Remote Setup Mode………………………………………………………………………..…………………..
3.
APPENDIX
Pan/Tilt/Zoom Camera Installation…………………………………………………...……….................……
1.
External Sensor and Relay Installation …..……………………………………….......................................
2.
Trouble Shooting ………………………………………………………………………………………………...
3.
[NOTE] The default ID and password of administrator for Server program are ‘admin’ and ‘master’.
The default password for Client program is ‘1111’.
5
6
6
7
7
10
10
11
16
21
26
27
32
33
35
37
38
39
41
43
48
54
59
65
65
72
73
74
75
76
4
DIGITAL VIDEO RECORDER
d
(4pin)
SECTION 1 - PRODUCT INFORMATION
1. Video Capture Card Specifications
Audio/Sensor/Relay
I/O D-Sub Ports
Real Time Display
Card Connector
Tel e- swi tc h
Connection pin
(6pin)
IO boar
QLR1660 card
Product Video Card Video Input
QLR1660 1 card 4, 8, 16 120 / 100 4 8 4
QLR1660-2 2 SD cards 8, 16 240 / 200 8 16 8
* Recording Rate is the maximum frame rate in case of 320x240 resolution.
Video Input/Output
D-Sub Ports
Recording Rate
(NTSC / PAL)
Audio
Input
Sensor
Input
Relay
Output
Reset pin for
Watchdog
Resolution
320x240
640x240
640x480
5
QLR1660 User Manual
2. System Requirement
QLR1660 QLR1660-2
OS Windows 98SE / ME / 2000 / XP
CPU P-IV 1.6GHz or higher P-IV 3.0GHz or higher
Memory more than 256MB
HDD 5Gbyte or higher
VGA 32MB or higher *
* Recommended VGA: RIVA TNT 2, GeForce2 MX 100/200, GeForce2 MX 400,
[NOTE] You should use the VGA card with Hardware Acceleration function.
* A Standalone Grapics card (not integrated with the Motherboard) is essential for the correct functioning of the QLR1660
system. If you are unsure of your specific PC configuration, please refer to your hardware vendor for more information.
ATI XPERT 2000 Pro, ATI RADEON 7200
3. Package Contents
Your QLR1660 package includes the following：
1/2 Video Card(s) for QLR1660
QLR1660 Software CD (Including Driver, Application Software, and User Manual)
QLR1660 User Manual
26-pin D-sub type Video Input/Output Cable and 26-pin D-sub type I/O connection Cable
※ QLR1660 is designed with applying Original Certification System Code to prevent unauthorized Copy. Video
Capture card is also designed to operate after its authorized approval code is matched with Software program.
6
DIGITAL VIDEO RECORDER
(4pin)
SECTION 2 - INSTALLATION INSTRUCTIONS
1. QLR1660 Hardware Installations
[NOTE] Before installing the video capture card, turn off the computer’s power, unplug the power cable and
disconnect all other cables attached to the back of the computer.
1.1 Video Capture Card Installation
1.1.1 QLR1660 Installation
The QLR1660 uses a PCI interfaced video capture card that supports to 4, 8, 16 ports.
1. Remove the computer cover.
2. Insert the QLR1660 video capture card into the available PCI expansion slot.
3. Replace the computer cover and reconnect all cables.
4. Turn on the computer power. Windows will automatically detect the existing (QLR1660) card.
5. Now insert the CD and install the driver for QLR1660. (Refer to II-2. QLR1660 Driver Installation)
Audio/Sensor/Relay
I/O D-Sub Ports
Real Time Display
Card Connector
Tel e- swi tc h
Connection pin
(6pin)
QLR1660 card
Video Input/Output
D-Sub Ports
Reset pin for
Watchdog
7
QLR1660 User Manual
1.1.5 Watch-dog Installation for QLR1660
If the system is stopped by abnormal operation, watchdog will automatically reboot the computer. The watchdog
will restart the computer automatically if it did not receive any response from the system for more than 5 minutes.
Each QLR1660 video capture card has a Reset pin (4pin) for watch-dog. It should be connected to the
motherboard’s reset jumper and computer’s reset switch. Your motherboards’ RESET pin position might be
different from the illustration below. Please refer to your motherboard user manual for the actual
Reset pin for Watch-dog
(4pin)
QLR1660 video capture card
[NOTE] In case QLR1660-2 with two video capture cards, the cable should be connected to the
reset pin (4pin) for watch-dog of master card among two cards. Master card is that card is inserted in
slot located near to VGA card slot.
8
DIGITAL VIDEO RECORDER
1.2 Camera Installation
Cameras must be attached to the BNC connectors of the D-sub type video input/output cable connected to the video
capture cards in a specific order to avoid transmission problems. Cameras need to be installed according to the
numerical order marked on the BNC connector. Whether you use 4, 8 or 16 video input cables for 4, 8 or 16 channels
system, the pattern is the same - cameras will be installed to the numerical order marked on the BNC connector.
(For P/T/Z camera installation, refer to VI-1. Pan/Tilt/Zoom Camera Installation)
D-sub type 16ch Video Input/Output cable
[REFERENCE] Video Output is connected to CCTV monitor for spot and only ‘channel 1’ is displayed into monitor.
1.3 Audio & External Sensor/Relay Installation
Each system can come with D-sub type 26-pin I/O connector cable enabling user to connect audio inputs and sensor
inputs and relay outputs.
Audios, sensors and relays need to be connected according to the numerical order marked on the cable. Whether you
use various I/O connector cables for 4, 8 or 16 channels system, the pattern is the same.
(For detail sensor/relay installation, refer to VI-2. External Sensor and Relay Installation)
D-sub type I/O connector cable
- 4 audio inputs
- 8 sensor inputs
- 4 relay outputs
9
QLR1660 User Manual
2. QLR1660 Driver Installations
: Applied only to the QLR1660 Server Installation
* The screenshots shown below are taken from Windows XP and may vary slightly depending the Operating System
1) When you boot your computer after you have inserted the QLR1660 cards to the PCI slot, Windows will automatically
detect the existing card and the following message dialog appears automatically.
The first time you install the video card. Insert the QLR1660 Software CD and select Install from a list or specific
location (Advanced). Click the Next button.
2) Ensure that the driver CD is in the drive and select Search removable media. Click Next to continue
10
DIGITAL VIDEO RECORDER
3) The system will then find the video driver in the Software CD. Select the driver for your QLR1660 card from the list.
Click also Next button here.
Video driver for QLR1660, QLR1660-2: "WJ2160 Video Capture Device Ver5.0"
4) When the driver is located, the below screen will be shown. Click the Continue Anyway button to proceed.
11
QLR1660 User Manual
5) After the video driver installation finished, click the Finish button.
6) You need to continue installing the audio driver. Select Install the software automatically (Recommended) and click
the Next button.
Audio driver for QLR1660, QLR1660-2: "WJ2160 Audio Capture Device Ver5.0"
12
DIGITAL VIDEO RECORDER
8) When the driver is located, the below screen will be shown. Click the Continue Anyway button to proceed.
9) After the audio driver installation finished, click the Finish button.
For QLR1660 you are asked to repeat the procedures 4 times and for QLR1660-2, 8 times.
- Video driver for QLR1660, QLR1660-2: "WJ2160 Video Capture Device Ver5.0"
Audio driver for QLR1660, QLR1660-2: "WJ2160 Audio Capture Device Ver5.0"
13
QLR1660 User Manual
If you have installed QLR1660 , you will find the system’s device manager looking like the following figure.
3. QLR1660 Software Installations (Server, Client, Search)
[NOTE] You will need the product’s serial number to complete the installation of the software. The serial
1) Begin the software installation by double-clicking the Setup.exe icon in Install directory on the provided CD.
number may be found on the CD-ROM.
14
DIGITAL VIDEO RECORDER
2) In “VISTAPRO Version 1.0” dialog, click the Next button.
3) “Select Component” dialog appears. Choose one among 4 options that you want to install. Click Next button.
4) “Customer Information” dialog appears. Enter your (or your company’s) name and the product Serial Number. Click
Next button.
15
QLR1660 User Manual
5) “Choose Destination Location” dialog appears. Select folder where Setup will install files. Click Next button.
[CUASE] The default installation directory is C:\Program Files\VISTAPRO. When install is complete the following icons
will be displayed on the desktop
16
DIGITAL VIDEO RECORDER
6) “Select Program Folder” dialog appears. Choose a program folder name for this QLR1660 server system and click
Next button.
7) “Start Copying Files” dialog appears. Click the Next button.
8) If installing the files is finished, you choose whether or not register the QLR1660 Server on Startup Menu.
9) After this, if the following dialog appears, click the Yes button here.
[REFERENCE] If DirectX 8.1 software is already installed, it is installation procedure of from (9) to (12) will be omitted.
17
QLR1660 User Manual
10) Click also Yes button here.
11) Click also Yes button here.
12) Click OK button. Now you have successfully installed the DirectX8.1 for QLR1660 system.
[REFERENCE] If DirectX 8.1 software is first installed, your computer with Windows 98 or ME will be restarted.
18
DIGITAL VIDEO RECORDER
13) Before you use this QLR1660 program, must restart your computer.
Choose Yes, I want to restart my computer now and click OK button to finish setup.
14) After a moment, computer restarts and operates the QLR1660 Server system. And QLR1660 server will be displayed
automatically on the main screen.
* QLR1660 Server icon
, Client icon , Search icon .
19
QLR1660 User Manual
Channel Scree
SECTION 3 - HOW TO USE QLR1660 SERVER
1. Main Interface Window
When entering the Server Program, the main interface screen will open as shown below. There are several view modes
for efficient monitoring such as single channel, division screen (multi channel), and auto rotation view modes.
Launch the QLR1660 Server program by double-clicking the QLR1660 Server icon (
) on the desktop.
n
20
Screen
Window
■ Minimize button
■ System Status
Click to minimize the screen to the taskbar.
▶Date and Time Status Display (Current)
▶HDD Storage Status (% Used)
DIGITAL VIDEO RECORDER
: The Recycle HDD icon (
▶Client Connection Status
: Displays the Client connection status.
By double-clicking mouse here, you can see clients connected.
And, you can disconnect the clients using the administrator password.
[NOTE] The default password of administrator is ‘master’.
▶ Log View
: Shows event logs. You can see the details by double-clicking mouse on the viewer.
) is shown if in overwrite mode.
■ Setup button
■ Search button
You can see the log list by day because of saving list daily.
The operation information of start/end system, connection/disconnection, changing
system configuration, start/stop recording, etc. is recorded with time.
Click here to enter the Setup Mode.
[NOTE] The default ID and password of administrator are ‘admin’ and
Click here to enter the Search mode.
You can search recordings by camera number, date, time and event.
[NOTE] The default ID and password of administrator are ‘admin’ and ‘master’.
‘master’.
21
QLR1660 User Manual
■ Shutdown button
■ Relay On buttons
■ Pan/Tilt/Zoom
Control buttons
■ Color Control
buttons
■ Audio Speaker(On/Off)
/ Volume Control
buttons
Click this button to shutdown the main server application.
[NOTE] The default ID and password of administrator are ‘admin’ and ‘master’
If you click ‘RELAY’ tap, the relay on buttons appear.
- Clicking these buttons will activate the corresponding external relay
outputs.
(Refer to ‘SECTION 3-2-6. Speaker, Relay out Setup’ and ‘Appendix-2.
External Sensor and Relay Installation’.)
If you click ‘PTZ’ tap, the Pan/Tilt/Zoom control buttons appear.
- The following controls are available:
▪ Camera Selection to control Pan/Tilt/Zoom/Focus
▪ Tilt up/down (▲/▼)
▪ Pan left/right (◄/►)
▪ Zoom in/out (+/-)
▪ Focus in/out (+/-)
▪ Auxiliary (1,2,3)
(Refer to ‘Appendix -1.Pan/Tilt/Zoom Camera Installation’.)
Clicking the ‘Color’ tab brings up the picture adjustment controls.
.
- You are able to control the brightness, contrast, hue and saturation of
the video image.
Use for full-duplex audio communication with the QLR1660 Client system.
- Clicking the speaker button enables you to listen to the sound that is transmitted from the
connected QLR1660 Client.
- Control the volume by moving the volume control button.
[NOTE] For full-duplex audio communication with the QLR1660 Client system,
*Calling Message Window
: If the QLR1660 client tries to audio-communicate using ‘Call’ button (
the amplified microphone has to be connected to QLR1660 card and
an audio that microphone is connected actually has to be enabled at ‘Audio
recording and transferring' in System setup panel.
the ‘Calling message’ window is displayed as below.
),
If you click ‘OK’, the below window is displayed.
22
DIGITAL VIDEO RECORDER
■ Recording On/Off
buttons
■ Channel Select
buttons
If you click ‘OK’, the audio setup of the QLR1660 Server program is enabled.
- Audio Speaker button: On
- Audio recording and transferring: audio buttons are enabled
▶ Schedule Recording button (
: You can enable Schedule Recording according to Setup by clicking the ‘Schedule Rec.’
button.
[NOTE] If ‘Schedule Rec.’ button is off, all kind of recording (video and audio) components
configured in the Setup mode are disabled
▶ Group buttons (A,B)
: By clicking each group button (A,B), displays 8 channel recording buttons belongs to each
group
▶ Channel Recording buttons (1~16)
: Using these buttons, you are able to record each channel by clicking the desired channel.
The Continuous record icon (
)
) will be displayed on the camera screen.
▶ Group buttons (A,B)
: By clicking each group button (A,B), displays 8 channel select buttons belongs to each group
▶ Channel Select buttons (1~16)
: You are able to display each channel in the one-channel mode by clicking buttons
▶ Screen division buttons
: You can see the screen by various division modes of 1,4,6,9,10,13,16 channels with these
buttons.
▪
One channel screen (1-channel display)
4-division screen (4-channels display)
▪
▪
: Four 4-division screens of A(1~4ch), B(5~8ch), C(9~12ch), D(13~16ch) are
alternated by clicking.
*By double-clicking a channel on the screen, One channel screen of the channel and
4-division screen are changed alternately.
6-division screen (6-channels display)
: Three 6-division screens of A(1~6ch), B(6~11ch), C(11~16ch) are alternated by
clicking
*By double-clicking a small channel on the screen, the channel are displayed on the
left large screen.
23
Loading...