LOREX Technology LW2100 User Manual

www.lorexcctv.com

LW2 100 SER IES Ser ies Qui ck Star t Guide _R1 Pag e 1

COLOR DIGITAL WIRELESS SURVEILLANCE SYSTEM

WITH INDOOR/OUTDOOR NIGHT VISION CAMERA

LW2100 SERIES - QUICK START GUIDE

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Skill Level

Time

under 30 minutesunder 15 minutes under 60 minutes

Hand Tools Hardware

Router

Hi Speed

over 60 minutes

Time Tools Skills - Easy

Under 15 Minutes*

Hand Tools

Plug & Play connections,

On screen set up

* Installation time may vary based on

application and camera location

Connect power adapter to local 120V AC power outlet

B. Connect the Camera

A. Connect the Receiver

2

Connect one end of the
RCA Audio Video Cable
to the Receiver.

Connect the included
Wireless Antenna to
the receiver

1 3

View your Camera images on any Observation
Monitor with standard BNC inputs or TV with
RCA inputs**.

Connect the Video end of the RCA Cable to the
Female end of the included RCA/BNC Adaptor.
Connect the BNC Adaptor to your Observation
System or DVR with standard BNC inputs.
Connect the Audio end of the RCA cable to the
Audio input on your Observation System or DVR.

To view camera images on your TV, connect the
RCA Video and Audio ends of the RCA Audio/
Video cable to the Video and Audio inputs on
your TV.

1

2

Getting Started

** Requires viewing/recording device with RCA Video or BNC Video
input. Viewing/Recording device sold separately.

The Digital Wireless Surveillance System
comes with the following components:

• Digital Wireless Color Camera*

• Camera* Stands

• Slim Wireless Receiver

• Wireless Antenna’s for camera*
and receiver

• Power Adaptors* for camera* and
receiver

• Battery Adaptor Case for camera*

• RCA/BNC Adaptor

• RCA Audio/Video Cable*

• Instruction Manual

*Number of cameras may vary by model. Check your package for specific
content information.

*

Mount camera stand to
the wall

NOTE: Wireless cameras require a power source
(either an electrical outlet or battery power) to
operate. If you plan to permanently mount the
camera in a location, it is recommended to use
the included Camera Power adaptor to prevent
interruptions in the image, as the battery adaptor is
intended for a temporary power solution.

1

NOTE: Before you install a camera, carefully plan
where and how it will be positioned, and where you
will route the cable that connects the camera to the
power adaptor or battery adaptor. Before starting
permanent installation, verify its performance by
observing the image on a monitor when the camera
is positioned where it will be permanently installed.

4

Connect one end of the Camera Power
Adaptor to the camera and the other
end to an electrical outlet.

Connect the Wireless Antenna
to the camera.

2 3

Secure Camera to the
Stand.

NOTE: When adding cameras that were not included
in the original box, you will need to pair up the
camera with the receiver. Please refer to the Camera
Pairing Section of the User Manual.

LW2100 Series_QSG_EN_R1.indd 1 5/6/2008 5:04:56 PM

www.lorexcctv.com

LW2 100 SER IES Ser ies Qui ck Star t Guide _R1 Pag e 2

Digital Wireless Analog Wireless

 2.4 GHz Digital 2.4 GHz Analog

 Secure privacy ensured Non Secure, no privacy
 Interference FREE

Interference from

 Range up to 450 ft line of sight Up to 300 ft line of sight
 Pairing - hand shake between camera and receiver No Pairing - fixed channel allocation
 FHSS - Frequency Hopping Spread Spectrum Technology N/A
 Supports 2 resolutions

VGA: 640 x 480
QVGA: 320 x 240

Supports only one resolution

 Digital PTZ (Pan/Tilt/Zoom) N/A
 Signal strength Indicator N/A

NOTE: Decide whether the camera will be permanently wall
mounted or placed on a tabletop:

• If you decide to place the camera on a tabletop or other flat
surface (ensure to secure the camera with proper screws,
thereby preventing it from falling down and damaging the lens
and surface) the camera can easily be moved to different
locations as desired. (Using this option will allow you to use
the Battery adaptor, which provides flexibility by moving the
camera from room to room).

• If you decide to permanently mount the camera to a wall, make
sure to select a location close to a power outlet.

Did you know?

1. Connect camera to the Battery Adaptor.

You can move your camera around from one room to another with the use of the included
battery adaptor.

2

3

1

C. Receiver Function Buttons

Press the Left, Right, Up, Down buttons to navigate
in Menu Mode. Use these buttons to Pan/Tilt the
image in ZOOM Mode (QVGA Mode Only).

Press the M to enter or exit Menu Mode.

Press the ZOOM Button to Zoom In
(QVGA) or Zoom Out (VGA).

Press the CAM Button to switch to a
different Camera on the Receiver

About Digital Wireless

It’s all on the Web

For detailed setup information,
please refer to your User’s Manual.
For additional information, please
visit our website

www.lorexcctv.com/support

COLOR DIGITAL WIRELESS SURVEILLANCE SYSTEM

WITH INDOOR/OUTDOOR NIGHT VISION CAMERA

LW2100 SERIES - QUICK START GUIDE

WiFi

Bluetooth

Microwave

Cordless Phone

DIGITAL WIRELESS

The table above shows that Digital Wireless Technology offers many advantages over Analog wireless. When comparing a Digital Wireless solution to a wired solution,
it is important to be aware of the bandwidth limitations. Due to bandwidth constraints and depending on the signal strength the frame rate, which is measured in FPS
(Frames per Second) may be reduced. For example, a Digital Wireless camera in the highest resolution (VGA 640x480) will feature a lower frame rate compared to a
wired solution which provides 30 FPS. It is possible to achieve 30 FPS with Digital Wireless by using the lower resolution (QVGA 320x240). For specific Frame Rate
details, please refer to the Viewing Modes section in the User Manual.

WiFi

Bluetooth

MicrowaveCordless Phone

ANALOG WIRELESS

2. Slide open the Battery Adaptor Case to add batteries (not included).

3. Insert 4 x AA Batteries into the Battery Pack. Make sure to correctly
line up the Positive (+) and Negative (-) terminals of the batteries.

4. Slide the Battery Pack cover back on.

5. NOTE: It is recommended to remove the battery pack from the
camera when not in use.

©2008 Lorex Technology Inc.

As our product is subject to continuous improvement, Lorex Technology & subsidiaries reserve the right to modify product design, specifications & prices

without notice and without incurring any obligation. E&OE

LW2100 Series_QSG_EN_R1.indd 2 5/6/2008 5:05:35 PM