Lorex Technology LNWDB1-C User Manual
Package Contents
Mounting Screws &
Anchors (×4)
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use and handling of the product.
• Use the product within given temperature, humidity and voltage levels noted in the
product’s specications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,
chemical-based cleaners.
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
HD Video Doorbell
LNWDB1 Series
Quick Start Guide
lorex.com
HD Video Doorbell
Chime Kit
Door Frame Screws (×3)
Power Port Screws (×2)
Screwdriver
Doorbell & Chime Cables
Wire Caps (×3)
Disclaimers
• Not intended for submersion
in water. Installation
in a sheltered location
recommended.
• This camera includes an Auto
Mechanical IR Cut Filter. When
the camera changes between
Day/Night viewing modes, an
audible clicking noise may
be heard from the camera.
This clicking is normal, and
indicates that the camera lter
is working.
• Audio recording without
consent is illegal in certain
jurisdictions. Lorex Corporation
assumes no liability for use
of its products that does not
conform with local laws.
Dimensions
2.4”
60mm
7. 4 ”
187mm
2.4”
60mm
FCC Notice
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
1
2
3
4
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specications and prices, without notice and without incurring
any obligation. E&OE. All rights reserved.
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
Click on the Downloads tab
Product Overview STEP 1: Preparation
Front Panel
PIR sensor
Camera
IR LEDs
Speaker
Call button
Microphone
Indicator LED strip
Behavior Meaning
Pulsing • Calling
Solid Talking
Flashing • Network issues
• Resetting
• Hotspot active
• Ready for setup
Back Panel
microSD slot
Reset button
Power ports
Before beginning setup, there are some essential preparations to
make.
To prepare for installation:
• TURN OFF THE POWER RUNNING TO YOUR EXISTING
DOORBELL AT THE BREAKER.
• Remove your existing doorbell and disconnect wiring.
TIP: Bend the power cables so they do not fall through the hole in
the wall.
• Remove the metal mounting plate from the back of the doorbell
by removing the pre-inserted security screw on the bottom using
the start end of the included screwdriver.
STEP 2: Secure the mounting bracket
Next, choose one of the following bracket installations based on where you are mounting the doorbell:
For installing on brick, stucco, or siding:
For both installations, ensure the power cables from the wall t
comfortably through the hole in the mounting bracket.
Use the included mounting
screws and plastic anchors
to secure the mounting
bracket to the wall.
For installing on a metal door frame:
Use the included door
frame screws to secure the
mounting bracket to the door
frame.
NOTE
LNWDB1_QSG_EN_R1
STEP 3: Wiring the doorbell
STEP 4: Wiring the chime
Lorex Home Overview
Next, you will complete the wiring for your new doorbell.
Loop the power cables around the
power ports of the doorbell.
1
Use the included screws (×2) to
secure the power cables.
NOTE
If the power cables in the wall are not long enough,
use the optional power cable connectors and wire caps.
You must determine the type of doorbell chime you
have in your home: electronic or mechanical.
2
Push the wiring through the hole in the
wall or door frame. Slide the doorbell
down so the plastic tab on the doorbell
locks into the notch on the mounting
3
bracket.
Not sure? If your doorbell chime is a classic
*ding-dong* sound, chances are your chime is
mechanical. If you are still not sure, remove the
cover panel of your chime box - if you nd spring-
loaded levers and a physical metal chime, you have
a mechanical chime.
For users with a mechanical chime, follow the extra
steps below to complete the installation.
3. Connect the included chime kit to the green terminal on
the end of the included wiring as shown below.
4. Connect the wiring from the chime kit to the FRONT
and TRANS connectors in the chime box. Ensure that
the existing wiring stays connected as well.
NOTE: You may connect either wire to either
connector.
Overview of the live viewing screen and controls in the Lorex Home
app. For complete instructions on using the app, see the Lorex Home
app manual on your product page at lorex.com.
Live viewing screen:Live viewing screen:
Back to
previous
screen
Device name
Device
settings
For mechanical chime owners:
1. Remove the cover panel of your doorbell chime
box.
2. Loosen the screws labeled FRONT and TRANS
using the Phillips end of the included screwdriver.
Do not remove the screws, and be sure not to
detach any connected wiring.
FRONT
REAR TRANS
5. Mount the chime kit to the inside of your chime box, or
along the cover plate, using the included double-sided
tape.
IMPORTANT: Ensure the chime kit and wires are not
touching the chimes or any moving components inside
the chime box, or the doorbell chime will not sound
correctly.
Play back
recorded
video
Snapshot
2-way audio: tap to speak, tap again to disable
Pause / Play FullscreenViewing
modes
Streaming
quality*
Manual
recording
Mute /
Unmute
STEP 5: Connecting to the Lorex Home app
Finalize the physical installation of the doorbell and begin setup
on the Lorex Home app.
1. Download and install the free Lorex Home app
from the App Store or Google Play Store.
2. Tap the Lorex Home icon to launch the app. Tap
Sign up, then follow the on screen prompts to
create an account. Record your account details
below:
Email:
Account Password:
3. Reconnect power to the doorbell at the breaker.
4. Once the status LED on the doorbell is solid blue, tap +.
5. Scan the QR code on the back of the doorbell using your mobile
device’s camera.
NOTE: If your mobile device cannot scan the QR code, tap
Manually enter Device ID.
6. Press the RESET button on the back of the doorbell to enable the
device hotspot.
7. Tap Next in the Lorex Home app once the hotspot is enabled and
the LED strip is pulsing.
8. The app will connect your mobile device to the doorbell’s
hotspot.
9. Create a secure password for the camera. Record your camera
password below:
Doorbell Password:
10. Select your Wi-Fi network from the list, then enter the password to
connect your doorbell to the Internet.
11. Once the status LED on the doorbell is solid blue, tap Next to add
the doorbell to your Lorex Home account.
12. Set a name for the doorbel and congure date & time preferences,
then tap Complete to nish the setup.
13. Insert the included security screw
through the mounting bracket and into
the screw hole on the bottom of the
doorbell. Fasten tightly using the starshaped end of the included screwdriver
to complete the installation.
* Change the streaming quality to SD (Standard Denition) to conserve bandwidth while
watching live video. This will not impact the quality of recorded video.
Calling screen:
Reject
Answer
LNWDB1_QSG_EN_R1
Loading...